| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
A couple of fixes for GPIO polarity and regulators on the A64
olinuxino.
* tag 'sunxi-fixes-for-5.5' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a83t: Correct USB3503 GPIOs polarity
arm64: dts: allwinner: a64: olinuxino: Fix SDIO supply regulator
arm64: dts: allwinner: a64: olinuxino: Fix eMMC supply regulator
Link: https://lore.kernel.org/r/582f4fda-38af-43e8-af58-957aee5b9dd8.lettre@localhost
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
i.MX fixes for 5.5, round 2:
- Fix i.MX8MM SDMA1 AHB clock setting to remove a "Timeout waiting for CH0"
error seen with UART1.
- Correct compatible of RV3029 RTC device on imx6q-dhcom board.
- Correct interrupt trigger type for magnetometer on board
imx8mq-librem5-devkit.
- A series from Anson Huang to fix vdd3p0 power supplier for a few NXP
development board.
- Fix imx6q-icore-mipi board to use 1.5 version of i.Core MX6DL, so
that Ethernet interface on the board works properly.
- Fix Toradex Colibri board to get NAND flash support back.
- Fix SGTL5000 VDDIO regulator connection for imx6q-dhcom, which
is connected to PMIC SW2 output rather than a fixed 3V3 rail.
- Fix 'reg' of CPU node on imx7ulp to get rid of a warning given by
kernel.
- Fix endian setting for DCFG on LS1028A SoC, so that register access
of DCFG becomes correct.
* tag 'imx-fixes-5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx7: Fix Toradex Colibri iMX7S 256MB NAND flash support
ARM: dts: imx6sll-evk: Remove incorrect power supply assignment
ARM: dts: imx6sl-evk: Remove incorrect power supply assignment
ARM: dts: imx6sx-sdb: Remove incorrect power supply assignment
ARM: dts: imx6qdl-sabresd: Remove incorrect power supply assignment
ARM: dts: imx6q-icore-mipi: Use 1.5 version of i.Core MX6DL
arm64: dts: imx8mq-librem5-devkit: use correct interrupt for the magnetometer
ARM: dts: imx6q-dhcom: Fix SGTL5000 VDDIO regulator connection
ARM: dts: imx7ulp: fix reg of cpu node
arm64: dts: imx8mm: Change SDMA1 ahb clock for imx8mm
arm64: dts: ls1028a: fix endian setting for dcfg
ARM: dts: imx6q-dhcom: fix rtc compatible
Link: https://lore.kernel.org/r/20200110011836.GW4456@T480
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
arm-soc: Amlogic fixes for v5.5-rc
* tag 'amlogic-fixes' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson-sm1-sei610: add gpio bluetooth interrupt
dt-bindings: reset: meson8b: fix duplicate reset IDs
soc: amlogic: meson-ee-pwrc: propagate errors from pm_genpd_init()
soc: amlogic: meson-ee-pwrc: propagate PD provider registration errors
ARM: dts: meson8: fix the size of the PMU registers
arm64: dts: meson-sm1-sei610: gpio-keys: switch to IRQs
Link: https://lore.kernel.org/r/7hmuaweavi.fsf@baylibre.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Use of_device_id array to find the proper shdwc compatibile node.
SAM9X60's shdwc changes were not integrated when
commit eaedc0d379da ("ARM: at91: pm: add ULP1 support for SAM9X60")
was integrated.
Fixes: eaedc0d379da ("ARM: at91: pm: add ULP1 support for SAM9X60")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1576062248-18514-3-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
SAM9X60 PMC's has a different PMC. It was not integrated at the moment
commit 01c7031cfa73 ("ARM: at91: pm: initial PM support for SAM9X60")
was published.
Fixes: 01c7031cfa73 ("ARM: at91: pm: initial PM support for SAM9X60")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1576062248-18514-2-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Enable config flags for SAM9X60 SoC. This includes SoC flag
(CONFIG_SOC_SAM9X60) and IP/board specific flags as follows:
- atmel maxtouch
- flexcom
- XDMA
- I2S Multi-channel
- mikroelectronica proto board
- SAMA5D2's ADC
- atmel QSPI
- classd
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/1575035505-6310-10-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Use savedefconfig.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1575035505-6310-9-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The clock rate range for the TCB1 clock is missing. define it in the device
tree.
Reported-by: Karl Rudbæk Olsen <karl@micro-technic.com>
Fixes: d2e8190b7916 ("ARM: at91/dt: define sama5d3 clocks")
Link: https://lore.kernel.org/r/20200110172007.1253659-2-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Currently the maximum rate for peripheral clock is calculated based on a
typical 133MHz MCK. The maximum frequency is defined in the datasheet as a
ratio to MCK. Some sama5d3 platforms are using a 166MHz MCK. Update the
device trees to match the maximum rate based on 166MHz.
Reported-by: Karl Rudbæk Olsen <karl@micro-technic.com>
Fixes: d2e8190b7916 ("ARM: at91/dt: define sama5d3 clocks")
Link: https://lore.kernel.org/r/20200110172007.1253659-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
sama5d3_lcd.dtsi is already included by sama5d31.dtsi, itself included by
at91-linea.dtsi.
Link: https://lore.kernel.org/r/20191229203503.336593-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
PAZ00 board has two variants of DDR2 SDRAM devices for External Memory:
one is Hynix HY5PS1G831CLFP-Y5 and the other is Micron MT47H128M8CF-25:H.
The Micron variant doesn't have official timings in the wild, hence only
timings for the Hynix are added. The memory frequency-scaling was tested
using the Tegra20 devfreq driver.
Tested-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Rename the EMC node to external-memory-controller according to device
tree best practices.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The EMC hardware block needs access to the EMC clock in order to scale
the external memory frequency. Add the clocks property so that drivers
for the EMC can acquire a reference to the EMC clock.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add a fixed regulator and use it as power supply for RBG panel.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Add a fixed regulator and use it as power supply for DSI panel.
Fixes: 18c8866266 ("ARM: dts: stm32: Add display support on stm32f469-disco")
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Change non volatile node name from nvmem to efuse to be compliant
with yaml schema.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Change non volatile node name from nvmem to efuse to be compliant
with yaml schema.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Update of the mlahb node according to to DT bindings using json-schema
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Modify dma controller nodes name to fit with the standard naming.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Modify dma controller nodes name to fit with the standard naming.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Modify dma controller nodes name to fit with the standard naming.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
phy-names is required by usbotg_hs driver to get the phy, otherwise, it
considers that there is no phys property.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch enables USB OTG HS on stm32mp15 dkx in Peripheral mode.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch enables USB Host (USBH) EHCI controller on stm32mp15 dk boards.
As a hub is used between USBH and USB connectors, no need to enable
USBH OHCI controller: all low- and full-speed traffic is managed by the
hub.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch enables USBPHYC (USB PHY Controller on stm32mp15 DKx boards.
This enables the two usbphyc usb2 ports, which require 3 supplies:
3v3, 1v1 and 1v8.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Turns out when introducing the eMMC version the gpmi node required for
NAND flash support got enabled exclusively on Colibri iMX7D 512MB.
Fixes: f928a4a377e4 ("ARM: dts: imx7: add Toradex Colibri iMX7D 1GB (eMMC) support")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX7D is supported for either the v7-A or the v7-M cores,
but the latter causes a warning:
WARNING: unmet direct dependencies detected for ARM_ERRATA_814220
Depends on [n]: CPU_V7 [=n]
Selected by [y]:
- SOC_IMX7D [=y] && ARCH_MXC [=y] && (ARCH_MULTI_V7 [=n] || ARM_SINGLE_ARMV7M [=y])
Make the select statement conditional.
Fixes: 4562fa4c86c9 ("ARM: imx: Enable ARM_ERRATA_814220 for i.MX6UL and i.MX7D")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
imx6ul-14x14-evk does not have a GPIO dedicated for reading the card
detect pin on the eSDHC2 micro-SD port.
Pass the "broken-cd" property to describe the absence of the card detect
GPIO so that polling must be used.
According to Documentation/devicetree/bindings/mmc/mmc-controller.yaml:
broken-cd:
$ref: /schemas/types.yaml#/definitions/flag
description:
There is no card detection available; polling must be used.
Even though no error is oberved in the kernel, the lack of the
'broken-cd' property caused the micro-SD to not be detected in U-Boot,
so let's improve the device tree description to make it more accurate.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes: 96a9169cf621 ("ARM: dts: imx6sll-evk: Assign corresponding power supply for vdd3p0")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes: 3feea8805d6f ("ARM: dts: imx6sl-evk: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes: 37a4bdead109 ("ARM: dts: imx6sx-sdb: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes: 93385546ba36 ("ARM: dts: imx6qdl-sabresd: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for the VXT VL050-8048NT-C01 panel connected through
the 24 bit parallel LCDIF interface.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The EDIMM STARTER KIT i.Core 1.5 MIPI Evaluation is based on
the 1.5 version of the i.Core MX6 cpu module. The 1.5 version
differs from the original one for a few details, including the
ethernet PHY interface clock provider.
With this commit, the ethernet interface works properly:
SMSC LAN8710/LAN8720 2188000.ethernet-1:00: attached PHY driver
While before using the 1.5 version, ethernet failed to startup
do to un-clocked PHY interface:
fec 2188000.ethernet eth0: could not attach to PHY
Similar fix has merged for i.Core MX6Q but missed to update for DL.
Fixes: a8039f2dd089 ("ARM: dts: imx6dl: Add Engicam i.CoreM6 1.5 Quad/Dual MIPI starter kit support")
Cc: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
LAN8720 needs a reset of every clock enable. The reset needs
to be done at device level, due the flag PHY_RST_AFTER_CLK_EN.
So, add phy-handle by creating mdio child node inside fec.
This will eventually move the phy-reset-gpio which is defined
in fec node.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Engicam i.CoreM6 1.5 Quad/Dual MIPI dtsi is reusing fec node
from Engicam i.CoreM6 dtsi but have sampe copy of phy-reset-gpio
and phy-mode properties.
So, drop this phy reset methods from imx6qdl-icore-1.5 dsti file.
Cc: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The following warning is seen when building with W=1:
arch/arm/boot/dts/imx7s.dtsi:551.39-553.7: Warning (unique_unit_address): /soc/aips-bus@30000000/ocotp-ctrl@30350000/temp-grade@10: duplicate unit-address (also used in node /soc/aips-bus@30000000/ocotp-ctrl@30350000/speed-grade@10)
Since temp-grade and speed-grade point to the same node, replace them by
a single one to avoid the duplicate unit-address warning.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Without the onkey device it isn't possible to power off the system using
the X_PMIC_nONKEY signal which is routed to the SoM pin header.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The CRYPTO_TFM_RES_* flags were apparently meant as a way to make the
->setkey() functions provide more information about errors. But these
flags weren't actually being used or tested, and in many cases they
weren't being set correctly anyway. So they've now been removed.
Also, if someone ever actually needs to start better distinguishing
->setkey() errors (which is somewhat unlikely, as this has been unneeded
for a long time), we'd be much better off just defining different return
values, like -EINVAL if the key is invalid for the algorithm vs.
-EKEYREJECTED if the key was rejected by a policy like "no weak keys".
That would be much simpler, less error-prone, and easier to test.
So just remove CRYPTO_TFM_RES_MASK and all the unneeded logic that
propagates these flags around.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The CRYPTO_TFM_RES_BAD_KEY_LEN flag was apparently meant as a way to
make the ->setkey() functions provide more information about errors.
However, no one actually checks for this flag, which makes it pointless.
Also, many algorithms fail to set this flag when given a bad length key.
Reviewing just the generic implementations, this is the case for
aes-fixed-time, cbcmac, echainiv, nhpoly1305, pcrypt, rfc3686, rfc4309,
rfc7539, rfc7539esp, salsa20, seqiv, and xcbc. But there are probably
many more in arch/*/crypto/ and drivers/crypto/.
Some algorithms can even set this flag when the key is the correct
length. For example, authenc and authencesn set it when the key payload
is malformed in any way (not just a bad length), the atmel-sha and ccree
drivers can set it if a memory allocation fails, and the chelsio driver
sets it for bad auth tag lengths, not just bad key lengths.
So even if someone actually wanted to start checking this flag (which
seems unlikely, since it's been unused for a long time), there would be
a lot of work needed to get it working correctly. But it would probably
be much better to go back to the drawing board and just define different
return values, like -EINVAL if the key is invalid for the algorithm vs.
-EKEYREJECTED if the key was rejected by a policy like "no weak keys".
That would be much simpler, less error-prone, and easier to test.
So just remove this flag.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The recovery mode pin is currently named 'REC_MODE_L', which is
how the signal is called in the schematics. The Chrome OS ABI
requires the pin to be named 'RECOVERY_SW_L', which is also how
it is called on all other veyron devices. Rename the pin to match
the ABI.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200108092908.1.I3afd3535b65460e79f3976e9ebfa392a0dd75e01@changeid
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Enable fimd device node which is a display controller, and add panel
node required by it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The clock setup on Meson8 cannot achieve a Mali frequency of exactly
182.15MHz. The vendor driver uses "FCLK_DIV7 / 1" for this frequency,
which translates to 2550MHz / 7 / 1 = 364285714Hz.
Update the GPU operating point to that specific frequency to not confuse
myself when comparing the frequency from the .dts with the actual clock
rate on the system.
Fixes: c3ea80b6138cae ("ARM: dts: meson8b: add the Mali-450 MP2 GPU")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The clock setup on Meson8 cannot achieve a Mali frequency of exactly
182.15MHz. The vendor driver uses "FCLK_DIV7 / 2" for this frequency,
which translates to 2550MHz / 7 / 2 = 182142857Hz.
Update the GPU operating point to that specific frequency to not confuse
myself when comparing the frequency from the .dts with the actual clock
rate on the system.
Fixes: 7d3f6b536e72c9 ("ARM: dts: meson8: add the Mali-450 MP6 GPU")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The Meson8b clock controller is an evolution of the Meson8 clock
controller. The clock controller on Meson8b contains two identical mali
clock trees for glitch-free rate switching.
Use the correct compatible string to make use of the glitch free mux.
Fixes: b6db3936f2833c ("ARM: dts: meson: switch the clock controller to the HHI register area")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
ASPEED device tree fixes for 5.5
Fixes for some badly applied patches that went in to 5.5. There is also
a fix for an incorrect i2c address.
* tag 'aspeed-5.5-devicetree-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: aspeed: rainier: Fix fan fault and presence
ARM: dts: aspeed: rainier: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Remove duplicate flash nodes
ARM: dts: aspeed: tacoma: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Fix fsi master node
ARM: dts: aspeed-g6: Fix FSI master location
Link: https://lore.kernel.org/r/CACPK8XcjazgORXNZBU1ECMukXG4HA8D9VeDxiSPifDk_iB7_dw@mail.gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
With the new omap_prm driver added unconditionally, omap2 builds
fail when the reset controller subsystem is disabled:
drivers/soc/ti/omap_prm.o: In function `omap_prm_probe':
omap_prm.c:(.text+0x2d4): undefined reference to `devm_reset_controller_register'
Link: https://lore.kernel.org/r/20191216132132.3330811-1-arnd@arndb.de
Fixes: 3e99cb214f03 ("soc: ti: add initial PRM driver with reset control support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Selecting RESET_CONTROLLER is actually required, otherwise we
can get a link failure in the clock driver:
drivers/clk/davinci/psc.o: In function `__davinci_psc_register_clocks':
psc.c:(.text+0x9a0): undefined reference to `devm_reset_controller_register'
drivers/clk/davinci/psc-da850.o: In function `da850_psc0_init':
psc-da850.c:(.text+0x24): undefined reference to `reset_controller_add_lookup'
Link: https://lore.kernel.org/r/20191210195202.622734-1-arnd@arndb.de
Fixes: f962396ce292 ("ARM: davinci: support multiplatform build for ARM v5")
Cc: <stable@vger.kernel.org> # v5.4
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
Olof Johansson
Claudiu Beznea
Ingo Molnar
Alexandre Belloni
Dmitry Osipenko
Thierry Reding
Benjamin Gaignard
Arnaud Pouliquen
Amelie Delaunay
Marcel Ziswiler
Arnd Bergmann
Fabio Estevam
Anson Huang
Jagan Teki
Michael Trimarchi
Marco Felsch
Eric Biggers
Matthias Kaehlcke
Yangtao Li
Martin Blumenstingl