| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The dma_mask and coherent_dma_mask values were never set.
This prevented the media omap_vout driver from loading successfully.
Tested on a Pandaboard and Beagle XM board.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Move the native-mode property inside the display-timings node.
According to
Documentation/devicetree/bindings/display/panel/display-timing.txt.
native-mode is a property of the display-timings node.
If it's located outside of display-timings, the native-mode setting is
ignored and the first display timing is used (which is a problem only if
someone adds another display timing).
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move the native-mode property inside the display-timings node.
According to
Documentation/devicetree/bindings/display/panel/display-timing.txt.
native-mode is a property of the display-timings node.
If it's located outside of display-timings, the native-mode setting is
ignored and the first display timing is used (which is a problem only if
someone adds another display timing).
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move the native-mode property inside the display-timings node.
According to
Documentation/devicetree/bindings/display/panel/display-timing.txt.
native-mode is a property of the display-timings node.
If it's located outside of display-timings, the native-mode setting is
ignored and the first display timing is used (which is a problem only if
someone adds another display timing).
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move the native-mode property inside the display-timings node.
According to
Documentation/devicetree/bindings/display/panel/display-timing.txt.
native-mode is a property of the display-timings node.
If it's located outside of display-timings, the native-mode setting is
ignored and the first display timing is used (which is a problem only if
someone adds another display timing).
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move the native-mode property inside the display-timings node.
According to
Documentation/devicetree/bindings/display/panel/display-timing.txt.
native-mode is a property of the display-timings node.
If it's located outside of display-timings, the native-mode setting is
ignored and the first display timing is used (which is a problem only if
someone adds another display timing).
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move the native-mode property inside the display-timings node.
According to
Documentation/devicetree/bindings/display/panel/display-timing.txt.
native-mode is a property of the display-timings node.
If it's located outside of display-timings, the native-mode setting is
ignored and the first display timing is used (which is a problem only if
someone adds another display timing).
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move the native-mode property inside the display-timings node.
According to
Documentation/devicetree/bindings/display/panel/display-timing.txt.
native-mode is a property of the display-timings node.
If it's located outside of display-timings, the native-mode setting is
ignored and the first display timing is used (which is a problem only if
someone adds another display timing).
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move the native-mode property inside the display-timings node.
According to
Documentation/devicetree/bindings/display/panel/display-timing.txt.
native-mode is a property of the display-timings node.
If it's located outside of display-timings, the native-mode setting is
ignored and the first display timing is used (which is a problem only if
someone adds another display timing).
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The driver uses hardwire MMIO addresses instead of the data
that is passed in device tree. Change it over to only
hardcode the register offset values and allow compile-testing.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Tested-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
All the way back to introducing dma_common_mmap we've defaulted to mark
the pages as uncached. But this is wrong for DMA coherent devices.
Later on DMA_ATTR_WRITE_COMBINE also got incorrect treatment as that
flag is only treated special on the alloc side for non-coherent devices.
Introduce a new dma_pgprot helper that deals with the check for coherent
devices so that only the remapping cases ever reach arch_dma_mmap_pgprot
and we thus ensure no aliasing of page attributes happens, which makes
the powerpc version of arch_dma_mmap_pgprot obsolete and simplifies the
remaining ones.
Note that this means arch_dma_mmap_pgprot is a bit misnamed now, but
we'll phase it out soon.
Fixes: 64ccc9c033c6 ("common: dma-mapping: add support for generic dma_mmap_* calls")
Reported-by: Shawn Anastasio <shawn@anastas.io>
Reported-by: Gavin Li <git@thegavinli.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com> # arm64
|
|
Pull fall-through fixes from Gustavo A. R. Silva:
"Mark more switch cases where we are expecting to fall through, fixing
fall-through warnings in arm, sparc64, mips, i386 and s390"
* tag 'Wimplicit-fallthrough-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
ARM: ep93xx: Mark expected switch fall-through
scsi: fas216: Mark expected switch fall-throughs
pcmcia: db1xxx_ss: Mark expected switch fall-throughs
video: fbdev: omapfb_main: Mark expected switch fall-throughs
watchdog: riowd: Mark expected switch fall-through
s390/net: Mark expected switch fall-throughs
crypto: ux500/crypt: Mark expected switch fall-throughs
watchdog: wdt977: Mark expected switch fall-through
watchdog: scx200_wdt: Mark expected switch fall-through
watchdog: Mark expected switch fall-throughs
ARM: signal: Mark expected switch fall-through
mfd: omap-usb-host: Mark expected switch fall-throughs
mfd: db8500-prcmu: Mark expected switch fall-throughs
ARM: OMAP: dma: Mark expected switch fall-throughs
ARM: alignment: Mark expected switch fall-throughs
ARM: tegra: Mark expected switch fall-through
ARM/hw_breakpoint: Mark expected switch fall-throughs
|
|
Mark switch cases where we are expecting to fall through.
Fix the following warnings (Building: arm-ep93xx_defconfig arm):
arch/arm/mach-ep93xx/crunch.c: In function 'crunch_do':
arch/arm/mach-ep93xx/crunch.c:46:3: warning: this statement may
fall through [-Wimplicit-fallthrough=]
memset(crunch_state, 0, sizeof(*crunch_state));
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/arm/mach-ep93xx/crunch.c:53:2: note: here
case THREAD_NOTIFY_EXIT:
^~~~
Notice that, in this particular case, the code comment is
modified in accordance with what GCC is expecting to find.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
|
|
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning:
arch/arm/kernel/signal.c: In function 'do_signal':
arch/arm/kernel/signal.c:598:12: warning: this statement may fall through [-Wimplicit-fallthrough=]
restart -= 2;
~~~~~~~~^~~~
arch/arm/kernel/signal.c:599:3: note: here
case -ERESTARTNOHAND:
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
|
|
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings:
arch/arm/plat-omap/dma.c: In function 'omap_set_dma_src_burst_mode':
arch/arm/plat-omap/dma.c:384:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (dma_omap2plus()) {
^
arch/arm/plat-omap/dma.c:393:2: note: here
case OMAP_DMA_DATA_BURST_16:
^~~~
arch/arm/plat-omap/dma.c:394:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (dma_omap2plus()) {
^
arch/arm/plat-omap/dma.c:402:2: note: here
default:
^~~~~~~
arch/arm/plat-omap/dma.c: In function 'omap_set_dma_dest_burst_mode':
arch/arm/plat-omap/dma.c:473:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (dma_omap2plus()) {
^
arch/arm/plat-omap/dma.c:481:2: note: here
default:
^~~~~~~
Notice that, in this particular case, the code comment is
modified in accordance with what GCC is expecting to find.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
|
|
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings:
arch/arm/mm/alignment.c: In function 'thumb2arm':
arch/arm/mm/alignment.c:688:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if ((tinstr & (3 << 9)) == 0x0400) {
^
arch/arm/mm/alignment.c:700:2: note: here
default:
^~~~~~~
arch/arm/mm/alignment.c: In function 'do_alignment_t32_to_handler':
arch/arm/mm/alignment.c:753:15: warning: this statement may fall through [-Wimplicit-fallthrough=]
poffset->un = (tinst2 & 0xff) << 2;
~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~
arch/arm/mm/alignment.c:754:2: note: here
case 0xe940:
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
|
|
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning:
arch/arm/mach-tegra/reset.c: In function 'tegra_cpu_reset_handler_enable':
arch/arm/mach-tegra/reset.c:72:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
tegra_cpu_reset_handler_set(reset_address);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/arm/mach-tegra/reset.c:74:2: note: here
case 0:
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
|
|
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings:
arch/arm/kernel/hw_breakpoint.c: In function 'hw_breakpoint_arch_parse':
arch/arm/kernel/hw_breakpoint.c:609:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (hw->ctrl.len == ARM_BREAKPOINT_LEN_2)
^
arch/arm/kernel/hw_breakpoint.c:611:2: note: here
case 3:
^~~~
arch/arm/kernel/hw_breakpoint.c:613:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (hw->ctrl.len == ARM_BREAKPOINT_LEN_1)
^
arch/arm/kernel/hw_breakpoint.c:615:2: note: here
default:
^~~~~~~
arch/arm/kernel/hw_breakpoint.c: In function 'arch_build_bp_info':
arch/arm/kernel/hw_breakpoint.c:544:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if ((hw->ctrl.type != ARM_BREAKPOINT_EXECUTE)
^
arch/arm/kernel/hw_breakpoint.c:547:2: note: here
default:
^~~~~~~
In file included from include/linux/kernel.h:11,
from include/linux/list.h:9,
from include/linux/preempt.h:11,
from include/linux/hardirq.h:5,
from arch/arm/kernel/hw_breakpoint.c:16:
arch/arm/kernel/hw_breakpoint.c: In function 'hw_breakpoint_pending':
include/linux/compiler.h:78:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
# define unlikely(x) __builtin_expect(!!(x), 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
include/asm-generic/bug.h:136:2: note: in expansion of macro 'unlikely'
unlikely(__ret_warn_on); \
^~~~~~~~
arch/arm/kernel/hw_breakpoint.c:863:3: note: in expansion of macro 'WARN'
WARN(1, "Asynchronous watchpoint exception taken. Debugging results may be unreliable\n");
^~~~
arch/arm/kernel/hw_breakpoint.c:864:2: note: here
case ARM_ENTRY_SYNC_WATCHPOINT:
^~~~
arch/arm/kernel/hw_breakpoint.c: In function 'core_has_os_save_restore':
arch/arm/kernel/hw_breakpoint.c:910:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (oslsr & ARM_OSLSR_OSLM0)
^
arch/arm/kernel/hw_breakpoint.c:912:2: note: here
default:
^~~~~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
|
|
Pull kvm fixes from Paolo Bonzini:
"Bugfixes (arm and x86) and cleanups"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
selftests: kvm: Adding config fragments
KVM: selftests: Update gitignore file for latest changes
kvm: remove unnecessary PageReserved check
KVM: arm/arm64: vgic: Reevaluate level sensitive interrupts on enable
KVM: arm: Don't write junk to CP15 registers on reset
KVM: arm64: Don't write junk to sysregs on reset
KVM: arm/arm64: Sync ICH_VMCR_EL2 back when about to block
x86: kvm: remove useless calls to kvm_para_available
KVM: no need to check return value of debugfs_create functions
KVM: remove kvm_arch_has_vcpu_debugfs()
KVM: Fix leak vCPU's VMCS value into other pCPU
KVM: Check preempted_in_kernel for involuntary preemption
KVM: LAPIC: Don't need to wakeup vCPU twice afer timer fire
arm64: KVM: hyp: debug-sr: Mark expected switch fall-through
KVM: arm64: Update kvm_arm_exception_class and esr_class_str for new EC
KVM: arm: vgic-v3: Mark expected switch fall-through
arm64: KVM: regmap: Fix unexpected switch fall-through
KVM: arm/arm64: Introduce kvm_pmu_vcpu_init() to setup PMU counter index
|
|
Support has been added to the OMAP IOMMU driver to fix a boot hang
issue on OMAP remoteprocs with AMMU/Unicache, caused by an improper
AMMU/Unicache state upon initial deassertion of the processor reset.
The issue is described in detail in the next three paragraphs.
All the Cortex M3/M4 IPU processor subsystems in OMAP SoCs have a
AMMU/Unicache IP that dictates the memory attributes for addresses
seen by the processor cores. The AMMU/Unicache is configured/enabled
by the SCACHE_CONFIG.BYPASS bit - a value of 1 enables the cache and
mandates all addresses accessed by M3/M4 be defined in the AMMU. This
bit is not programmable from the host processor. The M3/M4 boot
sequence starts out with the AMMU/Unicache in disabled state, and
SYS/BIOS programs the AMMU regions and enables the Unicache during
one of its initial boot steps. This SCACHE_CONFIG.BYPASS bit is
however enabled by default whenever a RET reset is applied to the IP,
irrespective of whether it was previously enabled or not. The AMMU
registers lose their context whenever this reset is applied. The reset
is effective as long as the MMU portion of the subsystem is enabled
and clocked. This behavior is common to all the IPU and DSP subsystems
that have an AMMU/Unicache.
The IPU boot sequence involves enabling and programming the MMU, and
loading the processor and releasing the reset(s) for the processor.
The PM setup code currently sets the target state for most of the
power domains to RET. The L2 MMU can be enabled, programmed and
accessed properly just fine with the domain in hardware supervised
mode, while the power domain goes through a RET->ON->RET transition
during the programming sequence. However, the ON->RET transition
asserts a RET reset, and the SCACHE_CONFIG.BYPASS bit gets auto-set.
An AMMU fault is thrown immediately when the M3/M4 core's reset is
released since the first instruction address itself will not be
defined in any valid AMMU regions. The ON->RET transition happens
automatically on the power domain after enabling the iommu due to
the hardware supervised mode.
This patch adds and invokes the .set_pwrdm_constraint pdata ops, if
present, during the OMAP IOMMU enable and disable functions to resolve
the above boot hang issue. The ops will allow to invoke a mach-omap2
layer API pwrdm_set_next_pwrst() in a multi-arch kernel environment.
The ops also returns the current power domain state while enforcing
the constraint so that the driver can store it and use it to set back
the power domain state while releasing the constraint. The pdata ops
implementation restricts the target power domain to ON during enable,
and back to the original power domain state during disable, and thereby
eliminating the conditions for the boot issue. The implementation is
effective only when the original power domain state is either RET or
OFF, and is a no-op when it is ON or INACTIVE.
The .set_pwrdm_constraint ops need to be plugged in pdata-quirks
for the affected remote processors to be able to boot properly.
Note that the current issue is seen only on kernels with the affected
power domains programmed to enter RET. For eg., IPU1 on DRA7xx is in a
separate domain and is susceptible to this bug, while the IPU2 subsystem
is within CORE power domain, and CORE RET is not supported on this SoC.
IPUs on OMAP4 and OMAP5 are also susceptible since they are in CORE power
domain, and CORE RET is a valid power target on these SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
At the moment, the way we reset CP15 registers is mildly insane:
We write junk to them, call the reset functions, and then check that
we have something else in them.
The "fun" thing is that this can happen while the guest is running
(PSCI, for example). If anything in KVM has to evaluate the state
of a CP15 register while junk is in there, bad thing may happen.
Let's stop doing that. Instead, we track that we have called a
reset function for that register, and assume that the reset
function has done something.
In the end, the very need of this reset check is pretty dubious,
as it doesn't check everything (a lot of the CP15 reg leave outside
of the cp15_regs[] array). It may well be axed in the near future.
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
We now have a proper clocksource driver for davinci. Switch the dm355
platform to using it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Boards from the dm* family rely on register offset definitions from
arch/arm/mach-davinci/include/mach/time.h. We'll be removing this file
soon, so move the required defines to davinci.h where the rest of such
constants live.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
We now have a proper clocksource driver for davinci. Switch the da830
platform to using it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
We now have a proper clocksource driver for davinci. Switch the da850
platform to using it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Currently the timer code checks if the clock pointer passed to it is
good (!IS_ERR(clk)). The new clocksource driver expects the clock to
be functional and doesn't perform any checks so emit a warning if
clk_get() fails. Apply this to all davinci platforms.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Switch all davinci boards supporting device tree to using the new
clocksource driver: remove the previous OF_TIMER_DECLARE() from
mach-davinci and select davinci-timer for ARCH_DAVINCI.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Exynos5250-based Arndale board has one eSATA port, so enable AHCI-platform
driver, which handles it.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Exynos AHCI (SATA) controller has only one port for SATA device. According
to AHCI driver bindings (ata/ahci-platform.txt), if the bootloader doesn't
program the PORTS_IMPL register to proper value, the available port map has
to be provided by 'ports-implemented' device tree property. This fixes
SATA operation on Exynos5250-based boards since Linux v4.5.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Replace tab with space after assignment operator.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The VDDEE regulator is basically a copy of the VCCK regulator. VDDEE
supplies for example the Mali GPU and is controlled by PWM_D instead of
PWM_C.
Add the VDDEE PWM regulator and make it the supply of the Mali GPU.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The VDDEE regulator is basically a copy of the VCCK regulator. VDDEE
supplies for example the Mali GPU and is controlled by PWM_D instead of
PWM_C.
Add the VDDEE PWM regulator and make it the supply of the Mali GPU.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The VDDEE regulator is basically a copy of the VCCK regulator. VDDEE
supplies for example the Mali GPU and is controlled by PWM_D instead of
PWM_C.
Add the VDDEE PWM regulator and make it the supply of the Mali GPU.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The PWM_D output is used for the VDDEE PWM regulator which supplies for
example the Mali GPU on the EC-100 and Odroid-C1 boards. Add the output
pin the VDDEE regulators can be added.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
If unspecified in DT, the fifo sizes are not automatically detected by
the dwmac1000 dma driver and the reported fifo sizes default to 0.
Because of this, flow control will be turned off on the device.
Add the fifo sizes provided by the datasheet in the SoC in DT so
flow control may be enabled if necessary.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Update the panel node with latest version of the panel used on the system.
Add missing pincontrol phandle to the panel node.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Before this change the device tree description of qspi node for
second memory on BK4 board was wrong (applicable to old, removed
fsl-quadspi.c driver).
As a result this memory was not recognized correctly when used
with the new spi-fsl-qspi.c driver.
From the dt-bindings:
"Required SPI slave node properties:
- reg: There are two buses (A and B) with two chip selects each.
This encodes to which bus and CS the flash is connected:
<0>: Bus A, CS 0
<1>: Bus A, CS 1
<2>: Bus B, CS 0
<3>: Bus B, CS 1"
According to above with new driver the second SPI-NOR memory shall
have reg=<2> as it is connected to Bus B, CS 0.
Fixes: a67d2c52a82f ("ARM: dts: Add support for Liebherr's BK4 device (vf610 based)")
Suggested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move the native-mode property inside the display-timings node.
According to
Documentation/devicetree/bindings/display/panel/display-timing.txt.
native-mode is a property of the display-timings node.
If it's located outside of display-timings, the native-mode setting is
ignored and the first display timing is used (which is a problem only if
someone adds another display timing).
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use a space before and after assignment operator to have consistent
style.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The "vqmmc-1-8-v" and "ocr-limit" properties are not documented
anywhere, so just remove them.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
OV5645 camera sensor can be used on several i.MX boards, such as
imx6qdl-wandboard, imx7d-pico, imx6ul-pico, etc.
Select the OV5645 driver by default.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
imx6qdl-wandboard can be connected to a OV5645 camera via
MIPI CSI port. Add support for it.
PAD_GPIO_6 has been originally used for the Ethernet FEC
ERR006687 workaround, but it needs to be used to provide the
camera sensor clock, so adjust it accordingly.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This is like commit 0ca87bd5baa6 ("ARM: dts: rockchip: Add pin names
for rk3288-veyron-jerry") and other similar commits, but for the
veyron fievel board (and tiger, which includes the fievel .dtsi).
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Fix/improve a few things for veyron fievel/tiger:
- move 'vccsys' regulator from tiger to fievel, both boards
have it (and tiger includes the fievel .dtsi)
- move 'ext_gmac' node below regulators
- fix GPIO ids of vcc5_host1 and vcc5_host2 regulators
- remove reset configuration from 'gmac' node, this is already done
in rk3288.dtsi
- fixed style issues of some multi-line comments
- switch 'vcc18_lcdt', 'vdd10_lcd' and 'vcc33_ccd' regulators off
during suspend
- no pull-up on the Bluetooth wake-up pin, there is an external
pull-up. The signal is active low, add the 'bt_host_wake_l'
pinctrl config
- move BC 1.2 pins up in the pinctrl config to keep 'wake only' pins
separate
- add BC 1.2 pins to sleep config
Fixes: 0067692b662e ("ARM: dts: rockchip: add veyron-fievel board")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Pull arm swiotlb support from Christoph Hellwig:
"This fixes a cascade of regressions that originally started with the
addition of the ia64 port, but only got fatal once we removed most
uses of block layer bounce buffering in Linux 4.18.
The reason is that while the original i386/PAE code that was the first
architecture that supported > 4GB of memory without an iommu decided
to leave bounce buffering to the subsystems, which in those days just
mean block and networking as no one else consumed arbitrary userspace
memory.
Later with ia64, x86_64 and other ports we assumed that either an
iommu or something that fakes it up ("software IOTLB" in beautiful
Intel speak) is present and that subsystems can rely on that for
dealing with addressing limitations in devices. Except that the ARM
LPAE scheme that added larger physical address to 32-bit ARM did not
follow that scheme and thus only worked by chance and only for block
and networking I/O directly to highmem.
Long story, short fix - add swiotlb support to arm when build for LPAE
platforms, which actuallys turns out to be pretty trivial with the
modern dma-direct / swiotlb code to fix the Linux 4.18-ish regression"
* tag 'arm-swiotlb-5.3' of git://git.infradead.org/users/hch/dma-mapping:
arm: use swiotlb for bounce buffering on LPAE configs
dma-mapping: check pfn validity in dma_common_{mmap,get_sgtable}
|
|
Enable support for QSPI block on STM32 SoCs.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This enables the driver for STM32 booster regulator found on stm32mp1.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds FMC2 NAND controller support used by STM32MP SOCs.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch removes "ngpios" and "gpio-ranges" information from
stm32mp157-pinctrl.dtsi file as it is now filled in stm32mp157 pinctrl
package files.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
Hans Verkuil
Martin Kaiser
Arnd Bergmann
Greg Kroah-Hartman
Christoph Hellwig
Linus Torvalds
Gustavo A. R. Silva
Suman Anna
Marc Zyngier
Bartosz Golaszewski
Marek Szyprowski
Krzysztof Kozlowski
Martin Blumenstingl
Jerome Brunet
Marek Vasut
Lukasz Majewski
Fabio Estevam
Ezequiel Garcia
Matthias Kaehlcke
Patrice Chotard
Fabrice Gasnier
Christophe Kerello
Alexandre Torgue