| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Enable hdmi bridge sii9022 & display controller.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Fixes for omap variants
Three fixes mostly for dra7 SoC variants that have some devices disabled
compared to the base SoC. These got broken by the change of making devices
probe with ti-sysc interconnect target module and went unnnoticed for a
while. And there is no clkcel bit for timer12 unlike timer1. Also included
is a GPIO direction fix for phytec SDIO card detection.
* tag 'omap-for-v5.2/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x phytec boards: Fix cd-gpios active level
ARM: dts: dra72x: Disable usb4_tm target module
ARM: dts: Drop bogus CLKSEL for timer12 on dra7
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
DaVinci fixes for v5.2 kernel.
This addresses an issue with probe of IO expander on DA850 EVM. There is
also a WARN_ON() fix on DA850 and DA830 devices.
* tag 'davinci-fixes-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: da8xx: specify dma_coherent_mask for lcdc
ARM: davinci: da850-evm: call regulator_has_full_constraints()
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
mvebu fixes for 5.2 (part 1)
Fixing defconfig allowing to use Ethernet again on Armada 38x based
boards
* tag 'mvebu-fixes-5.2-1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu_v7_defconfig: fix Ethernet on Clearfog
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.2-rc1, please pull the following:
- Florian fixes the remaining Broadcom DTS files to have a valid
device_type = "memory" property which was missed during the removal of
skeleton.dtsi
* tag 'arm-soc/for-5.2/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm: Add missing device_type = "memory" property
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Fixes for omap variants for dra7 mmc voltage and boot issues
This series contains dra7 mmc voltage fixes, and fixes to the recent
changes to probe devices with device tree data insteas of legacy
platform data:
- Two fixes for dra7 mmc that needs 1.8V mode disabled as in case of a
reset, the bootrom will try to access the mmc card at 3.3V potentially
damaging the card
- Two regression fixes for am335x d_can. We must allow devices with no
control registers for ti-sysc interconnect target module driver for
at least d_can, and we remove the incorrect control registers for
d_can. And we must configure the osc clock for d_can as otherwise
register access may fail depending on the bootloader version
- Four regression fixes for dra7 variant dts files to tag rtc and usb4
as disabled for dra71x and dra76x. These SoC variants do not have
these devices, and got accidentally enabled when the L4 interconnect
got defined in the dra7-l4.dtsi for the dra7 SoC family
* tag 'omap-for-v5.2/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra71x: Disable usb4_tm target module
ARM: dts: dra71x: Disable rtc target module
ARM: dts: dra76x: Disable usb4_tm target module
ARM: dts: dra76x: Disable rtc target module
ARM: dts: dra76x: Update MMC2_HS200_MANUAL1 iodelay values
ARM: dts: am57xx-idk: Remove support for voltage switching for SD card
bus: ti-sysc: Handle devices with no control registers
ARM: dts: Configure osc clock for d_can on am335x
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
i.MX fixes for 5.2:
- A build fix for soc-imx8 driver which needs SOC_BUS support. To
avoid dealing with the dependency for every single i.MX SoC bus
driver, we selects at from architecture level.
- A fix on i.MX SCU firmware driver to ensure SCU irq is enabled only
after IPC is ready.
- A regression fix on cpuidle-imx6sx driver, which causes some
characters loss on serial communication.
* tag 'imx-fixes-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: cpuidle-imx6sx: Restrict the SW2ISO increase to i.MX6SX
firmware: imx: SCU irq should ONLY be enabled after SCU IPC is ready
arm64: imx: Fix build error without CONFIG_SOC_BUS
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add support for USB networking as a module to qcom_defconfig since its
a useful feature to have for development purposes.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add the CMA (Contiguous Memory Allocator) for the MSM DRM/KMS driver,
the simple panel, and the TI LM3630A driver in order to support the
display on the LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add initial support for the display found on the LG Nexus 5 (hammerhead)
phone. This is based on work from Jonathan Marek.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add the MDP5, DSI and DSI PHY blocks for the display found on the
msm8974 SoCs. This is based on work from msm8916.dtsi and Jonathan
Marek.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add necessary device tree nodes for the main LCD backlight.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add support for the Synaptics RMI4 touchscreen that is found on the
Nexus 5.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Convert kdump documentation to ReST and add it to the
user faced manual, as the documents are mainly focused on
sysadmins that would be enabling kdump.
Note: the vmcoreinfo.rst has one very long title on one of its
sub-sections:
PG_lru|PG_private|PG_swapcache|PG_swapbacked|PG_slab|PG_hwpoision|PG_head_mask|PAGE_BUDDY_MAPCOUNT_VALUE(~PG_buddy)|PAGE_OFFLINE_MAPCOUNT_VALUE(~PG_offline)
I opted to break this one, into two entries with the same content,
in order to make it easier to display after being parsed in html and PDF.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
We need to pick up post-rc1 changes to various document files so they don't
get lost in Mauro's massive RST conversion push.
|
|
This sets CONFIG_CPUFREQ_DT=m in davinci_all_defconfig. This is used for
frequency scaling on device tree boards.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Enable cpufreq-dt support for da850-evm. The cvdd is supplied by the
tps65070 pmic with configurable output voltage. By default da850-evm
boards support frequencies up to 375MHz so enable this operating
point.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Add a fixed regulator for the da850-lcdk board along with board-specific
CPU configuration.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Add a fixed regulator for the LEGO EV3 board along with board-specific
CPU configuration.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
This adds a cpu node and operating points to the common da850.dtsi file.
All operating points above 300MHz are disabled by default.
Regulators need to be hooked up on a per-board basis.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
The lcdc device is missing the dma_coherent_mask definition causing the
following warning on da850-evm:
da8xx_lcdc da8xx_lcdc.0: found Sharp_LK043T1DG01 panel
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at kernel/dma/mapping.c:247 dma_alloc_attrs+0xc8/0x110
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 5.2.0-rc3-00077-g16d72dd4891f #18
Hardware name: DaVinci DA850/OMAP-L138/AM18x EVM
[<c000fce8>] (unwind_backtrace) from [<c000d900>] (show_stack+0x10/0x14)
[<c000d900>] (show_stack) from [<c001a4f8>] (__warn+0xec/0x114)
[<c001a4f8>] (__warn) from [<c001a634>] (warn_slowpath_null+0x3c/0x48)
[<c001a634>] (warn_slowpath_null) from [<c0065860>] (dma_alloc_attrs+0xc8/0x110)
[<c0065860>] (dma_alloc_attrs) from [<c02820f8>] (fb_probe+0x228/0x5a8)
[<c02820f8>] (fb_probe) from [<c02d3e9c>] (platform_drv_probe+0x48/0x9c)
[<c02d3e9c>] (platform_drv_probe) from [<c02d221c>] (really_probe+0x1d8/0x2d4)
[<c02d221c>] (really_probe) from [<c02d2474>] (driver_probe_device+0x5c/0x168)
[<c02d2474>] (driver_probe_device) from [<c02d2728>] (device_driver_attach+0x58/0x60)
[<c02d2728>] (device_driver_attach) from [<c02d27b0>] (__driver_attach+0x80/0xbc)
[<c02d27b0>] (__driver_attach) from [<c02d047c>] (bus_for_each_dev+0x64/0xb4)
[<c02d047c>] (bus_for_each_dev) from [<c02d1590>] (bus_add_driver+0xe4/0x1d8)
[<c02d1590>] (bus_add_driver) from [<c02d301c>] (driver_register+0x78/0x10c)
[<c02d301c>] (driver_register) from [<c000a5c0>] (do_one_initcall+0x48/0x1bc)
[<c000a5c0>] (do_one_initcall) from [<c05cae6c>] (kernel_init_freeable+0x10c/0x1d8)
[<c05cae6c>] (kernel_init_freeable) from [<c048a000>] (kernel_init+0x8/0xf4)
[<c048a000>] (kernel_init) from [<c00090e0>] (ret_from_fork+0x14/0x34)
Exception stack(0xc6837fb0 to 0xc6837ff8)
7fa0: 00000000 00000000 00000000 00000000
7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
7fe0: 00000000 00000000 00000000 00000000 00000013 00000000
---[ end trace 8a8073511be81dd2 ]---
Add a 32-bit mask to the platform device's definition.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
The BB expander at 0x21 i2c bus 1 fails to probe on da850-evm because
the board doesn't set has_full_constraints to true in the regulator
API.
Call regulator_has_full_constraints() at the end of board registration
just like we do in da850-lcdk and da830-evm.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
This enables wake up on Bluetooth activity when the device is
suspended. The BT_HOST_WAKE signal is only connected on devices
with BT module that are connected through UART.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Run savedefconfig to cleanup and reorganize the configs. Most entries
are only moved around and few options disappear because of defaults.
However this removes the already disabled OSS Emulation and OSS
Sequencer API (SND_MIXER_OSS, SND_PCM_OSS, SND_SEQUENCER_OSS). These
were already disabled (hidden by missing SND_OSSEMUL and SND_SEQUENCER)
and are not strictly hardware related, therefore they are not necessary
for providing reference hardware config.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add crypto node in device tree for CAAM support.
Noteworthy is that on 7ulp the interrupt line is shared
between the two job rings.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Constify the ctx and iv arguments to crypto_chacha_init() and the
various chacha*_stream_xor() functions. This makes it clear that they
are not modified.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Enable ECSPI2 and bind CPLD to both chip selects.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The LS1021A-TSN is a development board built by VVDN/Argonboards in
partnership with NXP.
It features the LS1021A SoC and the first-generation SJA1105T Ethernet
switch for prototyping implementations of a subset of IEEE 802.1 TSN
standards.
It has two regular Ethernet ports and four switched, TSN-capable ports.
It also features:
- One Arduino header
- One expansion header
- Two USB 3.0 ports
- One mini PCIe slot
- One SATA interface
- Accelerometer, gyroscope, temperature sensors
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
With
commit 6104c37094e729f3d4ce65797002112735d49cd1
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Aug 1 17:32:07 2017 +0200
fbcon: Make fbcon a built-time depency for fbdev
we have a static dependency between fbcon and fbdev, and we can
replace the indirection through the notifier chain with a function
call.
v2: Sam Ravnborg noticed that mach-pxa/am200epd.c has a notifier too,
and listens to this.
...
Looking at the code it seems to wait for some fb to show up, so that
it can get the framebuffer base address from the fb_info struct. I
suspect his is some firmware fbdev. Then it uses that information to
let the real fbdev driver (metronomefb.c by the looks) get at the
framebuffer memory.
This doesn't looke like it's easy to fix (except by deleting the
entire thing, seems untouched since 2008, we might be able to get away
with that), so let's just stuff a few #ifdef into fb.h and fbmem.c and
cry over them for a bit.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Cc: Yisheng Xie <ysxie@foxmail.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Konstantin Khorenko <khorenko@virtuozzo.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Steve Sakoman <steve@sakoman.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190528090304.9388-11-daniel.vetter@ffwll.ch
|
|
Allows to use the SD interface at a higher speed mode if the card
supports it. For this the signaling voltage is switched from 3.3V to
1.8V under the usdhc1's drivers control.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This converts the Wolfson Micro WM831x DCDC converter to use
a GPIO descriptor for the GPIO driving the DVS pin.
There is just one (non-DT) machine in the kernel using this, and
that is the Wolfson Micro (now Cirrus) Cragganmore 6410 so we
patch this board to pass a descriptor table and fix up the driver
accordingly.
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: Richard Fitzgerald <rf@opensource.cirrus.com>
Cc: patches@opensource.cirrus.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The IOP3xx has some elaborate code to directly slam the
GPIO lines multiplexed with I2C down low before enablement,
apparently a workaround for a hardware bug found in the
early chips.
After consulting the developer documentation for IOP80321
and IOP80331 I can clearly see that this may be useful for
IOP80321 family (mach-iop32x) but it is highly dubious for
any 80331 series or later chip: in these chips the lines
are not multiplexed for UARTs.
We convert the code to pass optional GPIO descriptors
and register these only on the 80321-based boards where
it makes sense, optionally obtain them in the driver and
use the gpiod_set_raw_value() to ascertain the line gets
driven low when needed.
The GPIO driver does not give the GPIO chip a reasonable
label so the patch also adds that so that these machine
descriptor tables can be used.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
According to latest docs imx7d chips can go from 800 to 1200 mhz.
Maximum frequency is determined from two speed grading bits present in
OCOTP fuses at same location as other imx chips.
Also update to "typical" voltages from latest datasheet, 25mv higher
than current dts.
All imx7s parts are still fixed at 800mhz
Based on:
* IMX7DCEC Rev. 6, 03/2019
* IMX7SCEC Rev. 6, 03/2019
* IMX7DRM Rev. 1, 01/2018 Page 1102
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The imx-cpufreq-dt driver can handle speed grading bits on imx7d just
like on imx8mq and imx8mm.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
|
|
Compared to kernel 5.0, patches merged for 5.1 added support for A38x'
PHY guarded by a config option which was not enabled by default. As a
result, there was no eth1 and eth2 on a Solid Run Clearfog Base.
Ensure that A38x PHY is enabled on mvebu.
[gregory: issue appeared in 5.1 not in 5.2 and added Fixes tag]
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: David S. Miller <davem@davemloft.net>
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Fixes: a10c1c8191e0 ("net: marvell: neta: add comphy support")
Cc: stable@kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This updates the WL1831 bluetooth to use the serial serdev driver
interface.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i2c2 bus has a external plug which enables the easy connection of external
"bricks" with sensors of various kinds, while i2c4 on the Extended/Full boards
has a pair of on board motion sensors, accelerometer and magnetometer on one chip
and gyroscope on another so it makes sense to enable these i2c buses for use.
Tested on UDOO Neo Full.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use the SPDX License Identifier for GPL-2.0+ OR X11
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
|
|
Baltos 5221/3220 devices provide CD signal on GPIO2_18.
Baltos 2110 device provides CD signal on GPIO1_15.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The PHY must add both tx and rx delay and not only on the tx clock.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
ARCH_BRCMSTB needs to use the BCM2835 pin controller for chips like
BCM7211 which adopted that pin controller for GPIO.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Allow the use of reset controllers on ARCH_BRCMSTB such as the
recently introduced RESET_BRCMSTB driver.
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Move the ADC from exynos5420.dtsi to a shared file between Exynos5410 and
Exynos542x: exynos54xx.dtsi. Enable the ADC on Odroid XU board.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
There's no reason why we can't enable chained scatterlist for RiscPC,
we already support chained scatterlists in the IOMD DMA support code.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Reduce the amount of IRQ handling code that RiscPC requires; there's no
need for this duplication if we place the virtual iomem base address for
each bank directly in the irq_data structure. Provide helpers to get
the base address, and setup the base address and register mask.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Move the assembly files for RiscPC from arch/arm/lib to mach-rpc so
that we contain RiscPC bits in one subdirectory.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Correctly parse the video information from the tagged list, so that we
end up with the right bytes-per-char values. When booting with a
tagged list rather than a param block, this allows the decompressor to
display its messages during boot on the screen.
(Boot loaders normally pass a param block on this platform, but the
latest boot loader version recently released does not.)
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Atomwide 3port serial cards seem to leave their interrupts active when
exiting RISC OS, resulting in an interrupt storm during boot, and the
expansion card interrupt being disabled. Avoid this by manually
disabling the interrupt on each serial port via a custom quirk function.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
Yannick Fertré
Olof Johansson
Brian Masney
Jonathan Marek
Mauro Carvalho Chehab
Jonathan Corbet
David Lechner
Bartosz Golaszewski
Douglas Anderson
Krzysztof Kozlowski
Iuliana Prodan
Eric Biggers
Marek Vasut
Vladimir Oltean
Daniel Vetter
Igor Opaniuk
Linus Walleij
Leonard Crestez
Tony Lindgren
Jan Kundrát
Peter Robinson
Yegor Yefremov
Doug Berger
Jim Quinlan
Russell King