| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Remove the child nodes of the sckc as they are not necessary anymore.
Also, switch to the new atmel,sama5d3-sckc compatible string to use the
proper startup time for the RC oscillator (500 µs instead of 75).
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Remove the child nodes of the sckc as they are not necessary anymore.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Remove the child nodes of the sckc as they are not necessary anymore.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Remove the child nodes of the sckc as they are not necessary anymore.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The SPI controller bindings require an address cell size of 1, and a size
cell size of 0. Let's put it at the DTSI level to make sure that's properly
enforced.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The chosen clocksource and clockevent bindings have never been accepted and
parsed, remove them.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Append I2C 1 for stm32mp157c-dk1.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Enable OV5640 camera sensor driver of MB1379A extension
board connected on CN7 connector of stm32mp157c-ev1 board:
bus-width is set to 8, data-shift is set to 2 (lines 9:2 are used),
hsync-active is set to 0 for horizontal synchro line active low,
vsync-active is set to 0 for vertical synchro line active low and
pclk-sample is set to 1 for pixel clock polarity sampling data
on rising edge of the pixel clock signal.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Add DCMI pins to stm32mp157c.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Add DCMI camera interface support on stm32mp157c.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Based on 1 normalized pattern(s):
the code contained herein is licensed under the gnu general public
license you may obtain a copy of the gnu general public license
version 2 or later at the following locations
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 4 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154042.707528683@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
licensed under gplv2 or later
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 118 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154040.961286471@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 or
later as published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 9 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154040.848507137@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
51 franklin street fifth floor boston ma 02110 1301 usa
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option [no]_[pad]_[ctrl] any later version this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin street fifth floor boston ma
02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 176 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154040.652910950@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Enable Vivante GPU driver for stm32mp157a-dk1 and dk2 boards.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Enable Vivante GPU driver for stm32mp157c-ed1 board.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Append Vivante GPU DT configuration.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add I2S pins muxing to stm32mp157.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds support of STM32 I2S on stm32mp157c.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Add SAI pins muxing to stm32mp157.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds support of STM32 SAI on stm32mp157c.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds jedec compatible for spi-nor flash
on stm32mp157c-ev1 (needed with new spi-mem interface).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds pinctrl sleep config for qspi on stm32mp157c-ev1
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
The joystick (B1) on stm32mp157c-ev1 uses gpios on STMFX gpio expander.
These gpios need a pin configuration (push-pull and bias-pull-down),
described under stmfx_pinctrl node.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds support for STMicroelectronics Multi-Function eXpander
(STMFX) on stm32mp157c-ev1. It is connected on i2c2.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Orange (LD2) and blue (LD4) leds on stm32746g-eval are connected on
STMFX gpio expander, offset 17 and 19.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
The joystick (B3) on stm32746g-eval uses gpios on STMFX gpio expander.
These gpios need a pin configuration (push-pull and bias-pull-up),
described under stmfx_pinctrl node.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds support for STMicroelectronics Multi-Function eXpander
(STMFX) on stm32746g-eval. It is connected on i2c1.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Four packages exist for stm32mp157 die. As ball-out is different between
them, this patch covers those differences by creating dedicated pinctrl
dtsi files. Each dtsi pinctrl package file describes the package ball-out
through gpio-ranges.
stm32mp157a-dk1 / dk2 boards embed a STM32MP_PKG_AC (TFBGA361 (12*12))
package.
stm32mp157c-ed1 / ev1 boards embed a STM32MP_PKG_AA (LFBGA448 (18*18))
package.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Amlogic's vendor kernel defines an OPP for the GPU on Meson8b boards
with a voltage of 1.15V. It turns out that the vendor kernel relies on
the bootloader to set up the voltage. The bootloader however sets a
fixed voltage of 1.10V.
Amlogic's patched u-boot sources (uboot-2015-01-15-23a3562521) confirm
this:
$ grep -oiE "VDD(EE|AO)_VOLTAGE[ ]+[0-9]+" board/amlogic/configs/m8b_*
board/amlogic/configs/m8b_m100_v1.h:VDDAO_VOLTAGE 1100
board/amlogic/configs/m8b_m101_v1.h:VDDAO_VOLTAGE 1100
board/amlogic/configs/m8b_m102_v1.h:VDDAO_VOLTAGE 1100
board/amlogic/configs/m8b_m200_v1.h:VDDAO_VOLTAGE 1100
board/amlogic/configs/m8b_m201_v1.h:VDDEE_VOLTAGE 1100
board/amlogic/configs/m8b_m201_v1.h:VDDEE_VOLTAGE 1100
board/amlogic/configs/m8b_m202_v1.h:VDDEE_VOLTAGE 1100
Another hint at this is the VDDEE voltage on the EC-100 and Odroid-C1
boards. The VDDEE regulator supplies the Mali GPU. It's basically a copy
of the VCCK (CPU supply) which means it's limited to 0.86V to 1.14V.
Update the operating voltage of the Mali GPU on Meson8b to 1.10V so it
matches with what the vendor u-boot sets.
Fixes: c3ea80b6138cae ("ARM: dts: meson8b: add the Mali-450 MP2 GPU")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Drop the undocumented "switch-delay" which is a left-over from my
experiments with an early lima kernel driver when it was still
out-of-tree and required this property on Amlogic SoCs.
Fixes: c3ea80b6138cae ("ARM: dts: meson8b: add the Mali-450 MP2 GPU")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The interrupts in Amlogic's vendor kernel sources are all contiguous.
There are two typos leading to pp2 and pp4 as well as ppmmu2 and ppmmu4
incorrectly sharing the same interrupt line.
Fix this by using interrupt 170 for pp2 and 171 for ppmmu2.
Also drop the undocumented "switch-delay" which is a left-over from my
experiments with an early lima kernel driver when it was still
out-of-tree and required this property on Amlogic SoCs.
Fixes: 7d3f6b536e72c9 ("ARM: dts: meson8: add the Mali-450 MP6 GPU")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The call to of_get_next_child returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./arch/arm/mach-bcm/board_bcm281xx.c:43:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 35, but without a corresponding object release within this function.
./arch/arm/mach-bcm/platsmp-brcmstb.c:337:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 329, but without a corresponding object release within this function.
./arch/arm/mach-bcm/platsmp-brcmstb.c:341:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 329, but without a corresponding object release within this functio
./arch/arm/mach-bcm/bcm63xx_smp.c:150:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 130, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Gregory Fong <gregory.0xf0@gmail.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
During the removal of the skeleton.dtsi file with commit abe60a3a7afb
("ARM: dts: Kill off skeleton{64}.dtsi") a number of Broadcom SoCs were
converted, but a few were left unoticed, now causing boot failures with
v5.1 since the kernel cannot find suitable memory.
Updating the .dtsi files with the property will be done next, since
there are some memory nodes that do not follow the proper naming
convention and lack an unit name.
Fixes: abe60a3a7afb ("ARM: dts: Kill off skeleton{64}.dtsi")
Reported-by: Kevin Hilman <khilman@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
|
|
|
|
usb4_tm is unsed on dra71 and accessing the module
with ti,sysc is causing a boot crash hence disable its target
module.
Fixes: 549fce068a3112 ("ARM: dts: dra7: Add l4 interconnect hierarchy and ti-sysc data")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Introduce dra71x.dtsi to include dra71x specific changes.
rtc is fused out on dra71 and accessing target module
register is causing a boot crash hence disable it.
Fixes: 549fce068a3112 ("ARM: dts: dra7: Add l4 interconnect hierarchy and ti-sysc data")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
usb4_tm is unsed on dra76 and accessing the module
with ti,sysc is causing a boot crash hence disable its target
module.
Fixes: 549fce068a3112 ("ARM: dts: dra7: Add l4 interconnect hierarchy and ti-sysc data")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
rtc is fused out on dra76 and accessing target module
register is causing a boot crash hence disable it.
Fixes: 549fce068a3112 ("ARM: dts: dra7: Add l4 interconnect hierarchy and ti-sysc data")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The call to of_get_next_child returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./arch/arm/mach-versatile/versatile_dt.c:315:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 302, but without a corresponding object release within this function.
./arch/arm/mach-versatile/versatile_dt.c:320:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 302, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This activates the AFS partition parsing on the Versatile
Express family.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This activates the AFS partition parsing on the RealView
family.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This activates the AFS partition parsing on the Versatile.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This activates the code for AFS partition parsing on
the Integrator.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Enable USB Host support for both the Type-C connector on the CPU board
and the Type-A plug on the sub board.
Both boards are also capable of USB Device operation as well after the
appropriate Device Tree modifications.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add USB Device support for RZ/A2.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
Alexandre Belloni
Maxime Ripard
Yannick Fertré
Hugues Fruchet
Thomas Gleixner
Pierre-Yves MORDRET
Olivier Moysan
Ludovic Barre
Amelie Delaunay
Alexandre Torgue
Martin Blumenstingl
Wen Yang
Florian Fainelli
Tony Lindgren
Keerthy
Linus Walleij
Chris Brandt