| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
There are two front-panel LEDs on MPC837xRDB and MPC8315RDB boards: PWR
and HDD. After adding appropriate nodes we can program these LEDs from
kernel and user space.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Since USB2 is shared with local bus, either local bus or USB2
should be disabled. By default U-Boot enables local bus, so we
have to disable USB2, otherwise kernel hangs:
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: irq 28, io base 0xffe22000
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
<hangs here>
Note that U-Boot doesn't clear 'status' property when it enables
USB2, so we have to comment out the whole node.
To enable USB2, one can issue
'setenv hwconfig usb2:dr_mode=<host|peripheral>' command at the
U-Boot prompt.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This patch adds support for eTSEC 2.0 as found in P1020.
The changes include introduction of the group nodes for
the etsec nodes.
Signed-off-by: Sandeep Gopalpet <sandeep.kumar@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Technically, whilst SEC v3.3 h/w honours the tls_ssl_stream descriptor
type, it lacks the ARC4 algorithm execution unit required to be able
to execute anything meaningful with it. Change the node to agree with
the documentation that declares that the sec3.3 really doesn't have such
a descriptor type.
Reported-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This is a trivial 4xx plaform that uses the new simple bsp from
Josh and is handy to use in simulators such as ISS or even Mambo
who don't properly implement most of the actual devices in the
SoC but really only the core.
Signed-off-by: Torez Smith <lnxtorez@linux.vnet.ibm.com>
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
The maple platform failed to load because it's firmware could not take a
link address of 0x4000000. A new platform type with a link address of
0x400000 had to be created for the maple.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/booke: Fix breakpoint/watchpoint one-shot behavior
powerpc: Reduce printk from pseries_mach_cpu_die()
powerpc: Move checks in pseries_mach_cpu_die()
powerpc: Reset kernel stack on cpu online from cede state
powerpc: Fix G5 thermal shutdown
powerpc/pseries: Pass CPPR value to H_XIRR hcall
powerpc/booke: Fix a couple typos in the advanced ptrace code
powerpc: Fix SMP build with disabled CPU hotplugging.
powerpc: Dynamically allocate pacas
powerpc/perf: e500 support
powerpc/perf: Build callchain code regardless of hardware event support.
powerpc/cpm2: Checkpatch cleanup
powerpc/86xx: Renaming following split of GE Fanuc joint venture
powerpc/86xx: Convert gef_pic_lock to raw_spinlock
powerpc/qe: Convert qe_ic_lock to raw_spinlock
powerpc/82xx: Convert pci_pic_lock to raw_spinlock
powerpc/85xx: Convert socrates_fpga_pic_lock to raw_spinlock
|
|
|
|
Conflicts:
Documentation/filesystems/proc.txt
arch/arm/mach-u300/include/mach/debug-macro.S
drivers/net/qlge/qlge_ethtool.c
drivers/net/qlge/qlge_main.c
drivers/net/typhoon.c
|
|
This patch renames GE Fanuc boards following the split-up of the GE Fanuc
joint venture. These boards are now made by GE Intelligent platorms.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Conflicts:
drivers/firmware/iscsi_ibft.c
|
|
|
|
This patch adds NOR Flash, LEDs and PIB support for MPC8568E-MDS
boards. Plus, move bcsr node into localbus node, and add bcsr5
gpio-controller node.
Some platform code modifications were also needed.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add the MSI section to the DTS file for the GE PPC9A.
Signed-off-by: Malcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Support for the SBC610 VPX Single Board Computer from GE (PowerPC MPC8641D).
This patch adds basic support for the on-board flash.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add the MSI section to the DTS file for the GE SBC610.
Signed-off-by: Malcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Correction to interrupt map mask for GE SBC310 XMC site and addition of
alias.
Signed-off-by: Malcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add the MSI section to the DTS file for the GE SBC310.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The DIU driver should bind against "fsl,mpc5121-diu"
directly. Add this compatible property to the match
table and fix DTS and platform code accordingly.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Collects several changes needed after applying
previous mpc5121 platform and driver patches:
- Add mpc5121 reset module node
- Clean up and fix NAND description, remove unused properties
here and correct NAND flash chip size.
- Clean up I2C nodes: remove obsolete "cell-index" properties,
add "fsl,preserve-clocking" property
- Add I2C RTC node for m41t61 RTC
- Add I2C nodes for AD7414 temperature sensor and AT24C32CD3 EEPROM
- Fix compatible property in DMA node
- Clean up CAN nodes, remove unused "cell-index" properties
- Fix compatible property in DIU node
- USB node changes:
- use "fsl,mpc5121-usb2-dr" compatible property only
- remove "port0" and "port1" properties as these are only used
for multi-port host(MHP) module which is not available
on MPC5121.
- use 'fsl,invert-drvvbus' and 'fsl,invert-pwr-fault' in
USB node for internal PHY to specify polarities
of the appropriate port pins.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Sync Glacier dts with latest Canyonlands version:
- Add l2 cache support
- Add NDFC support
- Add RTC support
- Add AD7414 hwmon support
- Change EMAC compatible node from emac4 to emac4sync and correct the
register size
- Add support for ISA holes on 4xx PCI/X/E
(as done in Benjamin Herrenschmidt's patch for Canyonlands)
- Add Crypto device node
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
Sync Arches dts with latest Canyonlands version:
- Add 16k FIFO size to supported EMAC nodes
- Add next-level-cache property
- Add Crypto device node
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
This patch adds NOR FLASH MTD support to the Katmai (440SPe) dts file.
For this the OPB ranges address is mapped differently (base 0x00000000
-> 0xe0000000). This results in the address being identical to the lower
32bit of its physical address. This is needed for the MTD mapping to work
correctly, since U-Boot will insert the physical addresses of the EBC
chip selects into the EBC ranges property. This is the way its done in
most other 4xx dts files as well.
Additionally with a small whitespace cleanup.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
|
|
After these change, when need to work in rtbi mode,
just change phy-connection-type to "rtbi".
Also, this work can be done by u-boot.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mkuboot.sh provides a basic wrapper for the 'mkimage' utility. Using
mkuboot.sh provides clearer error reporting and allows a toolchain to
use its own 'mkimage' executable specified by ${CROSS_COMPILE}mkimage.
Additionally, this brings PowerPC in line with other architectures
which already call mkimage via mkuboot.sh.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
|
|
|
|
The retry logic in ug_putc() is broken.
If the TX fifo is not ready and the counter runs out it will have a
value of -1 and no transfer should be attempted. Also, a counter
with a value of 0 means that the TX fifo got ready in the last try
and the transfer should be attempted.
Reported-by: "Juha Leppanen" <juha_motorsportcom@luukku.com>
Signed-off-by: "Juha Leppanen" <juha_motorsportcom@luukku.com>
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
* 'next' of git://git.secretlab.ca/git/linux-2.6: (23 commits)
powerpc: fix up for mmu_mapin_ram api change
powerpc: wii: allow ioremap within the memory hole
powerpc: allow ioremap within reserved memory regions
wii: use both mem1 and mem2 as ram
wii: bootwrapper: add fixup to calc useable mem2
powerpc: gamecube/wii: early debugging using usbgecko
powerpc: reserve fixmap entries for early debug
powerpc: wii: default config
powerpc: wii: platform support
powerpc: wii: hollywood interrupt controller support
powerpc: broadway processor support
powerpc: wii: bootwrapper bits
powerpc: wii: device tree
powerpc: gamecube: default config
powerpc: gamecube: platform support
powerpc: gamecube/wii: flipper interrupt controller support
powerpc: gamecube/wii: udbg support for usbgecko
powerpc: gamecube/wii: do not include PCI support
powerpc: gamecube/wii: declare as non-coherent platforms
powerpc: gamecube/wii: introduce GAMECUBE_COMMON
...
Fix up conflicts in arch/powerpc/mm/fsl_booke_mmu.c.
Hopefully even close to correctly.
|
|
The top portion of MEM2 (the second 64MB memory block) in the Nintendo
Wii video game console is used by the firmware running on the Starlet
processor.
Add code to calculate the portion of MEM2 safely useable by the
Broadway processor. When running under the 'mini' firmware this is
easily determined from an in-memory header. Otherwise, a safe default
is used.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Add support for the Nintendo Wii video game console to the powerpc
bootwrapper.
dtbImage.wii is a wrapped image that contains a flat device tree,
an entry point compatible with the Homebrew Channel and BootMii,
and an optional initrd.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Add a device tree source file for the Nintendo Wii video game console.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Add support for the Nintendo GameCube video game console to the powerpc
bootwrapper.
dtbImage.gamecube is a wrapped image that contains a flat device tree,
an entry point compatible with SDload, and an optional initrd.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Add a device tree source file for the Nintendo GameCube video game console.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Add support for using the USB Gecko adapter as a bootwrapper console on
the Nintendo GameCube and Wii video game consoles.
The USB Gecko is a 3rd party memory card interface adapter that provides
a EXI (External Interface) to USB serial converter.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Newer revs of the FPGA have a larger SD buffer.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
Add nodes for PPC440SPe DMA, I2O, XOR engines and Memory
Queue module which are used in the updated PPC440SPe ADMA
driver. Also extend plb ranges property to specify address
ranges for DMA0/1 and I2O engines.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
- Add nodes for PMC and GTM controllers. GTM4 can be used as a wakeup
source;
- Add fsl,magic-packet properties to eTSEC nodes, i.e. wake-on-lan
support. Unlike MPC8313 processors, MPC8315 can resume from deep
sleep upon magic packet reception.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Describe all LocalBus chipselects on MPC8349E-MITX board. Also add flash
bindings.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add OF descriptions of EEPROM, two GPIO extenders and SPD hanging on I2C
on this board.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
mpc8349 bears two GPIO controllers. Enable support for them.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The stanza for PCI was copied from Bamboo which has four PCI slots. Yosemite
only has one PCI slot which is mapped to IDSEL 12, ADDR 22, IRQ2 Vector 25,
INTA.
Signed-off-by: Curtis Wald <cwald@watchguardvideo.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
Set PCI-E node inbound DMA ranges size to 4GB for correct boot up of Katmai.
Signed-off-by: Pravin Bathija <pbathija@amcc.com>
Acked-by: Feng Kan <fkan@amcc.com>
Acked-by: Prodyut Hazarika <phazarika@amcc.com>
Acked-by: Loc Ho <lho@amcc.com>
Acked-by: Tirumala Reddy Marri <tmarri@amcc.com>
Acked-by: Victor Gallardo <vgallardo@amcc.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
|
|
|
|
Add basic support for the P4080 DS reference board. None of the data
path devices (ethernet, crypto, pme) are support at this time.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add support for NVRAM on GE Fanuc's PPC9A.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
Anton Vorontsov
Kim Phillips
Torez Smith
Corey Minyard
Linus Torvalds
Benjamin Herrenschmidt
Jiri Kosina
Martyn Welch
David S. Miller
Anton Vorontsov
Malcolm Crossley
Martyn Welch
Anatolij Gustschin
Stefan Roese
Daniel Mack
Liu Yu-B13201
Peter Tyser
Albert Herranz
Sean MacLennan
Dmitry Eremin-Solenikov
Curtis Wald
pbathija@amcc.com
Kumar Gala