| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The ISA specifies power save wakeup due to a machine check exception can
cause a machine check interrupt (rather than the usual system reset
interrupt).
The machine check handler copes with this by doing low level machine
check recovery without restoring full state from idle, then queues up a
machine check event for logging, then directly executes the same idle
instruction it woke from. This minimises the work done before recovery
is performed.
The problem is that it requires machine specific instructions and
knowledge of the book3s idle code. Currently it only has code to handle
POWER8 idle, so POWER9 crashes when trying to execute the P8 idle
instructions which don't exist in ISAv3.0B.
cpu 0x0: Vector: e40 (Emulation Assist) at [c0000000008f3810]
pc: c000000000008380: machine_check_handle_early+0x130/0x2f0
lr: c00000000053a098: stop_loop+0x68/0xd0
sp: c0000000008f3a90
msr: 9000000000081001
current = 0xc0000000008a1080
paca = 0xc00000000ffd0000 softe: 0 irq_happened: 0x01
pid = 0, comm = swapper/0
Instead of going to sleep after recovery, do the usual idle wakeup and
state restoration by calling into the normal idle wakeup path. This
reuses the normal idle wakeup paths.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Mahesh J Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The POWER8 idle code has a neat trick of programming the power on engine
to restore a low bit into HSPRG0, so idle wakeup code can test and see
if it has been programmed this way and therefore lost all state. Restore
time can be reduced if winkle has not been reached.
However this messes with our r13 PACA pointer, and requires HSPRG0 to be
written to. It also optimizes the slowest and most uncommon case at the
expense of another SPR write in the common nap state wakeup.
Remove this complexity and assume winkle sleeps always require a state
restore. This speedup could be made entirely contained within the winkle
idle code by counting per-core winkles and setting a thread bitmap when
all have gone to winkle.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The system reset idle handler system_reset_idle_common is relocated, so
relocation is not required to branch to kvm_start_guest. The superfluous
relocation does not result in incorrect code, but it does not compile
outside of exception-64s.S (with fixed section definitions).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The default implementation of ioremap_cache() is aliased to ioremap().
On powerpc ioremap() creates cache-inhibited mappings by default which
is almost certainly not what you wanted.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The macro is now pretty long and ugly on powerpc. In the light of further
changes needed here, convert it to a __weak variant to be over-ridden with a
nicer looking function.
Suggested-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Hypervisor Virtualization and Directed Hypervisor Doorbell interrupt handlers
use the macro EXC_VIRT_OOL_MASKABLE_HV for their relocation-on handlers, which
calls MASKABLE_RELON_EXCEPTION_HV_OOL, which uses the *real mode* interrupt
prolog. This means we needlessly rfid from virtual mode to virtual mode.
For POWER8 it only affects doorbell IPIs. Context switch microbenchmark between
threads with snooze disabled (which causes IPI) gets about 3% faster, about 370
cycles. Should be more important on POWER9 with global doorbells and HVI for
host interrupts.
Use the RELON variant instead to reduce overhead.
Fixes: 1707dd1613 ("powerpc: Save CFAR before branching in interrupt entry paths")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Fold some more detail into the change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This allows the host kernel to handle H_PUT_TCE, H_PUT_TCE_INDIRECT
and H_STUFF_TCE requests targeted an IOMMU TCE table used for VFIO
without passing them to user space which saves time on switching
to user space and back.
This adds H_PUT_TCE/H_PUT_TCE_INDIRECT/H_STUFF_TCE handlers to KVM.
KVM tries to handle a TCE request in the real mode, if failed
it passes the request to the virtual mode to complete the operation.
If it a virtual mode handler fails, the request is passed to
the user space; this is not expected to happen though.
To avoid dealing with page use counters (which is tricky in real mode),
this only accelerates SPAPR TCE IOMMU v2 clients which are required
to pre-register the userspace memory. The very first TCE request will
be handled in the VFIO SPAPR TCE driver anyway as the userspace view
of the TCE table (iommu_table::it_userspace) is not allocated till
the very first mapping happens and we cannot call vmalloc in real mode.
If we fail to update a hardware IOMMU table unexpected reason, we just
clear it and move on as there is nothing really we can do about it -
for example, if we hot plug a VFIO device to a guest, existing TCE tables
will be mirrored automatically to the hardware and there is no interface
to report to the guest about possible failures.
This adds new attribute - KVM_DEV_VFIO_GROUP_SET_SPAPR_TCE - to
the VFIO KVM device. It takes a VFIO group fd and SPAPR TCE table fd
and associates a physical IOMMU table with the SPAPR TCE table (which
is a guest view of the hardware IOMMU table). The iommu_table object
is cached and referenced so we do not have to look up for it in real mode.
This does not implement the UNSET counterpart as there is no use for it -
once the acceleration is enabled, the existing userspace won't
disable it unless a VFIO container is destroyed; this adds necessary
cleanup to the KVM_DEV_VFIO_GROUP_DEL handler.
This advertises the new KVM_CAP_SPAPR_TCE_VFIO capability to the user
space.
This adds real mode version of WARN_ON_ONCE() as the generic version
causes problems with rcu_sched. Since we testing what vmalloc_to_phys()
returns in the code, this also adds a check for already existing
vmalloc_to_phys() call in kvmppc_rm_h_put_tce_indirect().
This finally makes use of vfio_external_user_iommu_id() which was
introduced quite some time ago and was considered for removal.
Tests show that this patch increases transmission speed from 220MB/s
to 750..1020MB/s on 10Gb network (Chelsea CXGB3 10Gb ethernet card).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
This reworks helpers for checking TCE update parameters in way they
can be used in KVM.
This should cause no behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
The guest view TCE tables are per KVM anyway (not per VCPU) so pass kvm*
there. This will be used in the following patches where we will be
attaching VFIO containers to LIOBNs via ioctl() to KVM (rather than
to VCPU).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
This merges in the commits in the topic/ppc-kvm branch of the powerpc
tree to get the changes to arch/powerpc which subsequent patches will
rely on.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
PR KVM page fault handler performs eaddr to pte translation for a guest,
however kvmppc_mmu_book3s_64_xlate() does not preserve WIMG bits
(storage control) in the kvmppc_pte struct. If PR KVM is running as
a second level guest under HV KVM, and PR KVM tries inserting HPT entry,
this fails in HV KVM if it already has this mapping.
This preserves WIMG bits between kvmppc_mmu_book3s_64_xlate() and
kvmppc_mmu_map_page().
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
For completeness, this adds emulation of the lfiwax and lfiwzx
instructions. With this, all floating-point load and store instructions
as of Power ISA V2.07 are emulated.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
This adds emulation for the following integer loads and stores,
thus enabling them to be used in a guest for accessing emulated
MMIO locations.
- lhaux
- lwaux
- lwzux
- ldu
- lwa
- stdux
- stwux
- stdu
- ldbrx
- stdbrx
Previously, most of these would cause an emulation failure exit to
userspace, though ldu and lwa got treated incorrectly as ld, and
stdu got treated incorrectly as std.
This also tidies up some of the formatting and updates the comment
listing instructions that still need to be implemented.
With this, all integer loads and stores that are defined in the Power
ISA v2.07 are emulated, except for those that are permitted to trap
when used on cache-inhibited or write-through mappings (and which do
in fact trap on POWER8), that is, lmw/stmw, lswi/stswi, lswx/stswx,
lq/stq, and l[bhwdq]arx/st[bhwdq]cx.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
This adds missing stdx emulation for emulated MMIO accesses by KVM
guests. This allows the Mellanox mlx5_core driver from recent kernels
to work when MMIO emulation is enforced by userspace.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
This patch provides the MMIO load/store emulation for instructions
of 'double & vector unsigned char & vector signed char & vector
unsigned short & vector signed short & vector unsigned int & vector
signed int & vector double '.
The instructions that this adds emulation for are:
- ldx, ldux, lwax,
- lfs, lfsx, lfsu, lfsux, lfd, lfdx, lfdu, lfdux,
- stfs, stfsx, stfsu, stfsux, stfd, stfdx, stfdu, stfdux, stfiwx,
- lxsdx, lxsspx, lxsiwax, lxsiwzx, lxvd2x, lxvw4x, lxvdsx,
- stxsdx, stxsspx, stxsiwx, stxvd2x, stxvw4x
[paulus@ozlabs.org - some cleanups, fixes and rework, make it
compile for Book E, fix build when PR KVM is built in]
Signed-off-by: Bin Lu <lblulb@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
This provides functions that can be used for generating interrupts
indicating that a given functional unit (floating point, vector, or
VSX) is unavailable. These functions will be used in instruction
emulation code.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
Override pcibios_default_alignment() to set default alignment to PAGE_SIZE
for all PCI devices on PowerNV platform. Thus sub-page BARs would not
share a page and could be mapped into guest when VFIO passthrough them.
Signed-off-by: Yongji Xie <elohimes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Power9 DD1 does not implement SAO. Although it's not widely used, its presence
or absence is visible to user space via arch_validate_prot() so it's moderately
important that we get the value right.
Fixes: 7dccfbc325bb ("powerpc/book3s: Add a cpu table entry for different POWER9 revs")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Power9 does not implement the icswx instruction. This CPU feature is not visible
to userspace and is only used in the CONFIG_PPC_ICSWX code, which is generally
not enabled, and can only be triggered by other code using icswx, which should
not happen on Power9 systems in the first place. So impact should be minimal.
Fixes: c3ab300ea5 ("powerpc: Add POWER9 cputable entry")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Threshold feature when used with MMCRA [Threshold Event Counter Event],
MMCRA[Threshold Start event] and MMCRA[Threshold End event] will update
MMCRA[Threashold Event Counter Exponent] and MMCRA[Threshold Event
Counter Multiplier] with the corresponding threshold event count values.
Patch to export MMCRA[TECX/TECM] to userspace in 'weight' field of
struct perf_sample_data.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The LDST field and DATA_SRC in SIER identifies the memory hierarchy level
(eg: L1, L2 etc), from which a data-cache miss for a marked instruction
was satisfied. Use the 'perf_mem_data_src' object to export this
hierarchy level to user space.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This is relatively esoteric, and knowing that we don't have it makes life
easier in some cases rather than just an eventual -EINVAL from
pci_mmap_page_range().
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
We can declare it <linux/pci.h> even on platforms where it isn't going to
be defined. There's no need to have it littered through the various
<asm/pci.h> files.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Most of the almost-identical versions of pci_mmap_page_range() silently
ignore the 'write_combine' argument and give uncached mappings.
Yet we allow the PCIIOC_WRITE_COMBINE ioctl in /proc/bus/pci, expose the
'resourceX_wc' file in sysfs, and allow an attempted mapping to apparently
succeed.
To fix this, introduce a macro arch_can_pci_mmap_wc() which indicates
whether the platform can do a write-combining mapping. On x86 this ends up
being pat_enabled(), while the few other platforms that support it can just
set it to a literal '1'.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Prior to commit 2337d207288f ("powerpc/64: CONFIG_RELOCATABLE support for hmi
interrupts"), the branch from hmi_exception_early() to hmi_exception_realmode()
was just a bl hmi_exception_realmode, which the linker would turn into a bl to
the local entry point of hmi_exception_realmode. This was broken when
CONFIG_RELOCATABLE=y because hmi_exception_realmode() is not in the low part of
the kernel text that is copied down to 0x0.
But in fixing that, we added a new bug on little endian kernels. Because the
branch is now a bctrl when CONFIG_RELOCATABLE=y, we branch to the global entry
point of hmi_exception_realmode(). The global entry point must be called with
r12 containing the address of hmi_exception_realmode(), because it uses that
value to calculate the TOC value (r2).
This may manifest as a checkstop, because we take a junk value from r12 which
came from HSRR1, add a small constant to it and then use that as the TOC
pointer. The HSRR1 value will have 0x9 as the top nibble, which puts it above
RAM and somewhere in MMIO space.
Fix it by changing the BRANCH_LINK_TO_FAR() macro to always use r12 to load the
label we're branching to. This means r12 will be setup correctly on LE, fixing
this bug, and r12 is also volatile across function calls on BE so it's a good
choice anyway.
Fixes: 2337d207288f ("powerpc/64: CONFIG_RELOCATABLE support for hmi interrupts")
Reported-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Currently powerpc's asm/io.h includes linux/io.h, and linux/io.h
includes asm/io.h.
This can cause problems because depending on which is included first the
order of definitions between the two files will change.
The include of linux/io.h was added back in 2008 in commit b41e5fffe8b8
("[POWERPC] devres: Add devm_ioremap_prot()"). It's not entirely clear
it was needed then, but devm_ioremap_prot() has since been removed
entirely as unused, in dedd24a12fe6 ("powerpc: Remove unused
devm_ioremap_prot()").
So it seems to be unnecessary and can potentially cause problems, so
remove the include of linux/io.h from asm/io.h
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
POWER9 requires msgsync for receiver-side synchronization, and a DD1
workaround restricts IPIs to core-local.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Drop no longer needed asm feature macro changes]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
IPIs are a pretty hot path and we already have the ability to do asm feature
patching, so use it.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Change log detail]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
POWER9 changes requirements and adds new instructions for
synchronization.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Change the doorbell callers to know about their msgsnd addressing,
rather than have them set a per-cpu target data tag at boot that gets
sent to the cause_ipi functions. The data is only used for doorbell IPI
functions, no other IPI types, so it makes sense to keep that detail
local to doorbell.
Have the platform code understand doorbell IPIs, rather than the
interrupt controller code understand them. Platform code can look at
capabilities it has available and decide which to use.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Add the bit definition and use it in facility_unavailable_exception() so we can
intelligently report the cause if we take a fault for SCV. This doesn't actually
enable SCV.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Drop whitespace changes to the existing entries, flush out change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Currently sys_mmap() and sys_mmap2() (32-bit only), are not visible to the
syscall tracing machinery. This means users are not able to see the execution of
mmap() syscalls using the syscall tracer.
Fix that by using SYSCALL_DEFINE6 for sys_mmap() and sys_mmap2() so that the
meta-data associated with these syscalls is visible to the syscall tracer.
A side-effect of this change is that the return type has changed from unsigned
long to long. However this should have no effect, the only code in the kernel
which uses the result of these syscalls is in the syscall return path, which is
written in asm and treats the result as unsigned regardless.
Example output:
cat-3399 [001] .... 196.542410: sys_mmap(addr: 7fff922a0000, len: 20000, prot: 3, flags: 812, fd: 3, offset: 1b0000)
cat-3399 [001] .... 196.542443: sys_mmap -> 0x7fff922a0000
cat-3399 [001] .... 196.542668: sys_munmap(addr: 7fff922c0000, len: 6d2c)
cat-3399 [001] .... 196.542677: sys_munmap -> 0x0
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[mpe: Massage change log, add detail on return type change]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Recently in commit f6eedbba7a26 ("powerpc/mm/hash: Increase VA range to 128TB"),
we increased H_PGD_INDEX_SIZE to 15 when we're building with 64K pages. This
makes it larger than RADIX_PGD_INDEX_SIZE (13), which means the logic to
calculate MAX_PGD_INDEX_SIZE in book3s/64/pgtable.h is wrong.
The end result is that the PGD (Page Global Directory, ie top level page table)
of the kernel (aka. swapper_pg_dir), is too small.
This generally doesn't lead to a crash, as we don't use the full range in normal
operation. However if we try to dump the kernel pagetables we can trigger a
crash because we walk off the end of the pgd into other memory and eventually
try to dereference something bogus:
$ cat /sys/kernel/debug/kernel_pagetables
Unable to handle kernel paging request for data at address 0xe8fece0000000000
Faulting instruction address: 0xc000000000072314
cpu 0xc: Vector: 380 (Data SLB Access) at [c0000000daa13890]
pc: c000000000072314: ptdump_show+0x164/0x430
lr: c000000000072550: ptdump_show+0x3a0/0x430
dar: e802cf0000000000
seq_read+0xf8/0x560
full_proxy_read+0x84/0xc0
__vfs_read+0x6c/0x1d0
vfs_read+0xbc/0x1b0
SyS_read+0x6c/0x110
system_call+0x38/0xfc
The root cause is that MAX_PGD_INDEX_SIZE isn't actually computed to be
the max of H_PGD_INDEX_SIZE or RADIX_PGD_INDEX_SIZE. To fix that move
the calculation into asm-offsets.c where we can do it easily using
max().
Fixes: f6eedbba7a26 ("powerpc/mm/hash: Increase VA range to 128TB")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This merges the arch part of the XIVE support, leaving the final commit
with the KVM specific pieces dangling on the branch for Paul to merge
via the kvm-ppc tree.
|
|
POWER9 DD1.0 hardware has a bug where the SPRs of a thread waking up
from stop 0,1,2 with ESL=1 can endup being misplaced in the core. Thus
the HSPRG0 of a thread waking up from can contain the paca pointer of
its sibling.
This patch implements a context recovery framework within threads of a
core, by provisioning space in paca_struct for saving every sibling
threads's paca pointers. Basically, we should be able to arrive at the
right paca pointer from any of the thread's existing paca pointer.
At bootup, during powernv idle-init, we save the paca address of every
CPU in each one its siblings paca_struct in the slot corresponding to
this CPU's index in the core.
On wakeup from a stop, the thread will determine its index in the core
from the TIR register and recover its PACA pointer by indexing into
the correct slot in the provisioned space in the current PACA.
Furthermore, ensure that the NVGPRs are restored from the stack on the
way out by setting the NAPSTATELOST in paca.
[Changelog written with inputs from svaidy@linux.vnet.ibm.com]
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Call it a bug]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Move the piece of code in powernv/smp.c::pnv_smp_cpu_kill_self() which
transitions the CPU to the deepest available platform idle state to a
new function named pnv_cpu_offline() in powernv/idle.c. The rationale
behind this code movement is that the data required to determine the
deepest available platform state resides in powernv/idle.c.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
powerpc_debugfs_root is the dentry representing the root of the
"powerpc" directory tree in debugfs.
Currently it sits in asm/debug.h, a long with some other things that
have "debug" in the name, but are otherwise unrelated.
Pull it out into a separate header, which also includes linux/debugfs.h,
and convert all the users to include debugfs.h instead of debug.h.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We need to set LPES in order for normal external interrupts (0x500)
to be directed to the guest while running in guest state.
We also need HEIC set to prevent them to be sent to the host while
in host state.
With XIVE the host never gets one of these and wouldn't know how to
handle it. All host external interrupts come in via the new
hypervisor virtualization interrupts vector.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We have all sort of variants of MMIO accessors for the real mode
instructions. This creates a clean set of accessors based on
Linux normal naming conventions, replacing all occurrences of
the old ones in the tree.
I have purposefully removed the "out/in" variants in favor of
only including __raw variants. Any code using these is already
pretty much hand tuned to operate in a very specific environment.
I've fixed up the 2 users (only one of them actually needed
a barrier in the first place).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The function doesn't exist anymore
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
It's only used within the same file it's defined
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The XIVE interrupt controller is the new interrupt controller
found in POWER9. It supports advanced virtualization capabilities
among other things.
Currently we use a set of firmware calls that simulate the old
"XICS" interrupt controller but this is fairly inefficient.
This adds the framework for using XIVE along with a native
backend which OPAL for configuration. Later, a backend allowing
the use in a KVM or PowerVM guest will also be provided.
This disables some fast path for interrupts in KVM when XIVE is
enabled as these rely on the firmware emulation code which is no
longer available when the XIVE is used natively by Linux.
A latter patch will make KVM also directly exploit the XIVE, thus
recovering the lost performance (and more).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Fixup pr_xxx("XIVE:"...), don't split pr_xxx() strings,
tweak Kconfig so XIVE_NATIVE selects XIVE and depends on POWERNV,
fix build errors when SMP=n, fold in fixes from Ben:
Don't call cpu_online() on an invalid CPU number
Fix irq target selection returning out of bounds cpu#
Extra sanity checks on cpu numbers
]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Its value has never changed; we might as well make it part of the ABI instead
of using the return value of KVM_CHECK_EXTENSION(KVM_CAP_COALESCED_MMIO).
Because PPC does not always make MMIO available, the code has to be made
dependent on CONFIG_KVM_MMIO rather than KVM_COALESCED_MMIO_PAGE_OFFSET.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
Some powerpc platforms use this to move IRQs away from a CPU being
unplugged. This function has several bugs such as not taking the right
locks or failing to NULL check pointers.
There's a new generic function doing exactly the same thing without all
the bugs, so let's use it instead.
mpe: The obvious place for the select of GENERIC_IRQ_MIGRATION is on
HOTPLUG_CPU, but that doesn't work. On some configs PM_SLEEP_SMP will
select HOTPLUG_CPU even though its dependencies are not met, which means
the select of GENERIC_IRQ_MIGRATION doesn't happen. That leads to the
build breaking. Fix it by moving the select of GENERIC_IRQ_MIGRATION to
SMP.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
backmerge of mainline ia64 fix
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
backmerge of sorting the arch/powerpc/Kconfig
|
|
Some platforms (will) need to perform allocations before bringing
a new CPU online. Doing it from smp_ops->setup_cpu is the wrong
thing to do:
- It has no useful failure path (too late)
- Calling any allocator will enable interrupts prematurely
causing problems with large decrementer among others
Instead, add a new callback that is called from __cpu_up (so from
the context trying to online the new CPU) at a point where we
can safely allocate and handle failures.
This will be used by XIVE support.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Add 32 and 8 bit variants
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
Nicholas Piggin
Oliver O'Halloran
Naveen N. Rao
Alexey Kardashevskiy
Paul Mackerras
Bin Lu
Yongji Xie
Madhavan Srinivasan
David Woodhouse
Michael Ellerman
Balbir Singh
Gautham R. Shenoy
Benjamin Herrenschmidt
Paolo Bonzini
Al Viro