| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The goal is to avoid adding overhead to MMIO when only PIO is needed
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The DSCR (aka Data Stream Control Register) is supported on some
server PowerPC chips and allow some control over the prefetch
of data streams.
This patch allows the value to be specified per thread by emulating
the corresponding mfspr and mtspr instructions. Children of such
threads inherit the value. Other threads use a default value that
can be specified in sysfs - /sys/devices/system/cpu/dscr_default.
If a thread starts with non default value in the sysfs entry,
all children threads inherit this non default value even if
the sysfs value is changed later.
Signed-off-by: Alexey Kardashevskiy <aik@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
When we set up the TLB for ourselves on Book3E, we need to flush out any
old mappings established by the firmware or bootloader. At present we
attempt this with a tlbilx to flush everything, but this will leave behind
any entries with the IPROT bit set.
There are several good reason firmware might establish mappings with IPROT,
and in fact ePAPR compliant firmwares are required to establish their
initial mapped area with IPROT.
This patch, therefore adds more complex code to scan through the TLB upon
entry and flush away any entries that are not our own.
Signed-off-by: Jack Miller <jack@codezen.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Add the cputable entry, regs and setup & restore entries for
the PowerPC A2 core.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
mac-fec.c was setting individual UDP address registers instead of multicast
group address registers when joining a multicast group.
This prevented from correctly receiving UDP multicast packets.
According to datasheet, replaced hash_table_high and hash_table_low
with grp_hash_table_high and grp_hash_table_low respectively.
Also renamed hash_table_* with grp_hash_table_* in struct fec declaration
for 8xx: these registers are used only for multicast there.
Tested on a MPC5121 based board.
Build tested also against mpc866_ads_defconfig.
Signed-off-by: Andrea Galbusera <gizero@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An upcoming new ics backend will need to implement different matching
semantics to the current ones, which are essentially the RTAS ics
backends. So move the current match into the RTAS backend, and allow
other ics backends to override.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
SCOM is a side-band configuration bus implemented on some processors.
This code provides a way for code to map and operate on devices via
SCOM, while the details of how that is implemented is left up to a
SCOM "controller" in the platform code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
When we start a cpu we use smp_ops->kick_cpu(), which currently
returns void, it should be able to fail. Convert it to return
int, and update all uses.
Convert all the current error cases to return -ENOENT, which is
what would eventually be returned by __cpu_up() currently when
it doesn't detect the cpu as coming up in time.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
On Book3E, MMU_NO_CONTEXT != 0, but the slice_mm_new_context()
macro assumes that it is. This means that the map of the
page sizes for each slice is always initialized to zeroes
(which happens to be 4k pages), rather than to the correct
default base page size value - which might be 64k.
This patch corrects the problem.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Use MMU_NO_CONTEXT as the initialiser for mm_context.id on
nohash and hash64.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Wakeup comes from the system reset handler with a potential loss of
the non-hypervisor CPU state. We save the non-volatile state on the
stack and a pointer to it in the PACA, which the system reset handler
uses to restore things
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We need to wait a bit for them to have done their CPU setup
or we might end up with translation and EE on with different
LPCR values between threads
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This uses feature sections to arrange that we always use HSPRG1
as the scratch register in the interrupt entry code rather than
SPRG2 when we're running in hypervisor mode on POWER7. This will
ensure that we don't trash the guest's SPRG2 when we are running
KVM guests. To simplify the code, we define GET_SCRATCH0() and
SET_SCRATCH0() macros like the GET_PACA/SET_PACA macros.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Rework exception macros a bit to split offset from vector and add
some basic support for HDEC, HDSI, HISI and a few more.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Pass the register type to the prolog, also provides alternate "HV"
version of hardware interrupt (0x500) and adjust LPES accordingly
We tag those interrupts by setting bit 0x2 in the trap number
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
When running in Hypervisor mode (arch 2.06 or later), we store the PACA
in HSPRG0 instead of SPRG1. The architecture specifies that SPRGs may be
lost during a "nap" power management operation (though they aren't
currently on POWER7) and this enables use of SPRG1 by KVM guests.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This bit indicates that we are operating in hypervisor mode on a CPU
compliant to architecture 2.06 or later (currently server only).
We set it on POWER7 and have a boot-time CPU setup function that
clears it if MSR:HV isn't set (booting under a hypervisor).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This adds more SPR definitions used on newer processors when running
in hypervisor mode. Along with some other P7 specific bits and pieces
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This is a significant rework of the XICS driver, too significant to
conveniently break it up into a series of smaller patches to be honest.
The driver is moved to a more generic location to allow new platforms
to use it, and is broken up into separate ICP and ICS "backends". For
now we have the native and "hypervisor" ICP backends and one common
RTAS ICS backend.
The driver supports one ICP backend instanciation, and many ICS ones,
in order to accomodate future platforms with multiple possibly different
interrupt "sources" mechanisms.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This problem was noticed on an MPC855T platform. Ftrace did oops
when trying to write to the kernel text segment.
Many thanks to Joakim for finding the root cause of this problem.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
|
|
e500mc does not support the HID0/MSR mechanism that is used by e500_idle
(and there are also issues with waking on certain types of interrupts).
Further, even if napping is never actually enabled, just having
CPU_FTR_CAN_NAP will cause machine_init() to overwrite the board's supplied
ppc_md.power_save().
We drop CPU_FTR_MAYBE_CAN_DOZE becuase we should use 'wait' instead on
e500mc.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The CPU_FTRS_POSSIBLE and CPU_FTRS_ALWAYS defines did not encompass
e5500 CPU features when built for 64-bit. This causes issues with
cpu_has_feature() as it utilizes the POSSIBLE & ALWAYS defines as part
of its check.
Create a unique CPU_FTRS_E5500 (as its different from CPU_FTRS_E500MC),
created a new group for 64-bit Book3e based CPUs and add CPU_FTRS_E5500
to that group.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
* 'for-linus2' of git://git.profusion.mobi/users/lucas/linux-2.6:
Fix common misspellings
|
|
Instead, keep it static, expose an accessor and use that from
the PowerMac code. Avoids easy namespace collisions and will
make it easier to consolidate with other implementations.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This allows us to stop abusing smp_ops->setup_cpu() for cleanup
tasks that have to take place after the initial boot time CPU
bringup.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The current code soft-disables, and then goes to NAP mode which
turns interrupts on. That means that if an interrupt occurs, we
will hit the masked interrupt code path which isn't what we want,
as it will return with EE off, which will either get us out of
NAP mode, or fail to enter it (according to spec).
Instead, let's just rely on the fact that it is safe to take
decrementer interrupts on an offline CPU and leave interrupts
enabled. We can also get rid of the special case in asm for
power4_cpu_offline_powersave() and just use power4_idle().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Use generic cpu_state, call idle_task_exit() properly, and
remove smp_core99_cpu_die() which isn't useful, the generic
function does the job just fine.
|
|
Remove the last remnants of cpu_enable(), everybody uses the normal
__cpu_up() path now
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Nobody uses it, besides we should always use the normal __cpu_up
path anyways
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Various thing are torn down when a CPU is hot-unplugged. That CPU
is expected to go back to start_secondary when re-plugged to re
initialize everything, such as clock sources, maps, ...
Some implementations just return from cpu_die() callback
in the idle loop when the CPU is "re-plugged". This is not enough.
We fix it using a little asm trampoline which resets the stack
and calls back into start_secondary as if we were all fresh from
boot. The trampoline already existed on ppc64, but we add it for
ppc32
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
avr32: Fix missing irq namespace conversion
powerpc: qe_ic: Rename get_irq_desc_data and get_irq_desc_chip
genirq: Remove the now obsolete config options and select statements
arm: versatile : Fix typo introduced in irq namespace cleanup
sound: Fixup the last user of the old irq functions
genirq: Remove obsolete comment
genirq: Remove now obsolete set_irq_wake()
sh: Fix irq cleanup fallout
x86: apb_timer: Fixup genirq fallout
genirq: Fix misnamed label in handle_edge_eoi_irq
Fix up crazy conflict in arch/powerpc/include/asm/qe_ic.h:
- commit eead4d5c63ff ("powerpc: qe_ic: Rename get_irq_desc_data and
get_irq_desc_chip") made the helper functions use
irq_desc_get_handler_data() instead of the legacy (and no longer
existing) get_irq_desc_data.
- commit d4db35e8dc96 ("powerpc/qe_ic: Fix another breakage from the
irq_data conversion") used irq_desc_get_chip_data() instead.
According to Thomas, the former is the correct direct conversion, but it
does look like both should work (arch/powerpc/sysdev/qe_lib/qe_ic.c
seems to initialize both to the same thing), and the chip data in some
ways is the more logical. Somebody should really decide on one of the
other.
This merge picks irq_desc_get_handler_data() as the straightforward pure
conversion to new names, as per Thomas.
|
|
These two functions disappeared in commit
0c6f8a8b917ad361319c8ace3e9f28e69bfdb4c1
"genirq: Remove compat code"
but they still exist in qe_ic.h.
This patch renames the function to their new names.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Lennert Buytenhek <buytenh@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
LKML-Reference: <20110330132504.GA31832@riccoc20.at.omicron.at>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Recent upstream builds with allmodconfig fail due to lack of space
between 0x3000 and 0x6000. We have a hard block at 0x7000 but we can
spare a page by moving the STAB0 from 0x6000 to 0x8000.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
These syscalls have been added recently:
name_to_handle_at
open_by_handle_at
clock_adjtime
syncfs
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
339 is the SPR number for MAS5 documented by Power ISA 2.06, and
implemented by e500mc. It is not yet used anywhere in the kernel,
so nothing should be relying on the wrong number.
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
pfns are unsigned long, but MEMORY_START is phys_addr_t. This leads
to page_to_pfn() returning phys_addr_t, and thus type mismatches in a few
print statements.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This is used by Alsa to mmap buffers allocated with dma_alloc_coherent()
into userspace. We need a special variant to handle machines with
non-coherent DMAs as those buffers have "special" virt addresses and
require non-cachable mappings
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
There is no user now.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: David Miller <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
minix bit operations are only used by minix filesystem and useless by
other modules. Because byte order of inode and block bitmaps is different
on each architecture like below:
m68k:
big-endian 16bit indexed bitmaps
h8300, microblaze, s390, sparc, m68knommu:
big-endian 32 or 64bit indexed bitmaps
m32r, mips, sh, xtensa:
big-endian 32 or 64bit indexed bitmaps for big-endian mode
little-endian bitmaps for little-endian mode
Others:
little-endian bitmaps
In order to move minix bit operations from asm/bitops.h to architecture
independent code in minix filesystem, this provides two config options.
CONFIG_MINIX_FS_BIG_ENDIAN_16BIT_INDEXED is only selected by m68k.
CONFIG_MINIX_FS_NATIVE_ENDIAN is selected by the architectures which use
native byte order bitmaps (h8300, microblaze, s390, sparc, m68knommu,
m32r, mips, sh, xtensa). The architectures which always use little-endian
bitmaps do not select these options.
Finally, we can remove minix bit operations from asm/bitops.h for all
architectures.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As the result of conversions, there are no users of ext2 non-atomic bit
operations except for ext2 filesystem itself. Now we can put them into
architecture independent code in ext2 filesystem, and remove from
asm/bitops.h for all architectures.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Introduce little-endian bit operations by renaming existing powerpc native
little-endian bit operations and changing them to take any pointer types.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This makes the little-endian bitops take any pointer types by changing the
prototypes and adding casts in the preprocessor macros.
That would seem to at least make all the filesystem code happier, and they
can continue to do just something like
#define ext2_set_bit __test_and_set_bit_le
(or whatever the exact sequence ends up being).
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
Michael Ellerman
Alexey Kardashevskiy
Jack Miller
Benjamin Herrenschmidt
Andrea Galbusera
Michael Ellerman
Paul Mackerras
Stefan Roese
Scott Wood
Kumar Gala
Linus Torvalds
Lucas De Marchi
Richard Cochran
Stephen Rothwell
Varun Sethi
FUJITA Tomonori
Akinobu Mita