| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
On PowerPC it's very normal to not support all of the physical RAM in real mode.
To check if we're matching on the shared page or not, we need to know the limits
so we can restrain ourselves to that range.
So let's make it a define instead of open-coding it. And while at it, let's also
increase it.
Signed-off-by: Alexander Graf <agraf@suse.de>
v2 -> v3:
- RMO -> PAM (non-magic page)
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
When the guest turns on interrupts again, it needs to know if we have an
interrupt pending for it. Because if so, it should rather get out of guest
context and get the interrupt.
So we introduce a new field in the shared page that we use to tell the guest
that there's a pending interrupt lying around.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
While running in hooked code we need to store register contents out because
we must not clobber any registers.
So let's add some fields to the shared page we can just happily write to.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
When running in hooked code we need a way to disable interrupts without
clobbering any interrupts or exiting out to the hypervisor.
To achieve this, we have an additional critical field in the shared page. If
that field is equal to the r1 register of the guest, it tells the hypervisor
that we're in such a critical section and thus may not receive any interrupts.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
To communicate with KVM directly we need to plumb some sort of interface
between the guest and KVM. Usually those interfaces use hypercalls.
This hypercall implementation is described in the last patch of the series
in a special documentation file. Please read that for further information.
This patch implements stubs to handle KVM PPC hypercalls on the host and
guest side alike.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
When in kernel mode there are 4 additional registers available that are
simple data storage. Instead of exiting to the hypervisor to read and
write those, we can just share them with the guest using the page.
This patch converts all users of the current field to the shared page.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
The SRR0 and SRR1 registers contain cached values of the PC and MSR
respectively. They get written to by the hypervisor when an interrupt
occurs or directly by the kernel. They are also used to tell the rfi(d)
instruction where to jump to.
Because it only gets touched on defined events that, it's very simple to
share with the guest. Hypervisor and guest both have full r/w access.
This patch converts all users of the current field to the shared page.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
The DAR register contains the address a data page fault occured at. This
register behaves pretty much like a simple data storage register that gets
written to on data faults. There is no hypervisor interaction required on
read or write.
This patch converts all users of the current field to the shared page.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
The DSISR register contains information about a data page fault. It is fully
read/write from inside the guest context and we don't need to worry about
interacting based on writes of this register.
This patch converts all users of the current field to the shared page.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
One of the most obvious registers to share with the guest directly is the
MSR. The MSR contains the "interrupts enabled" flag which the guest has to
toggle in critical sections.
So in order to bring the overhead of interrupt en- and disabling down, let's
put msr into the shared page. Keep in mind that even though you can fully read
its contents, writing to it doesn't always update all state. There are a few
safe fields that don't require hypervisor interaction. See the documentation
for a list of MSR bits that are safe to be set from inside the guest.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
For transparent variable sharing between the hypervisor and guest, I introduce
a shared page. This shared page will contain all the registers the guest can
read and write safely without exiting guest context.
This patch only implements the stubs required for the basic structure of the
shared page. The actual register moving follows.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (71 commits)
powerpc/44x: Update ppc44x_defconfig
powerpc/watchdog: Make default timeout for Book-E watchdog a Kconfig option
fsl_rio: Add comments for sRIO registers.
powerpc/fsl-booke: Add e55xx (64-bit) smp defconfig
powerpc/fsl-booke: Add p5020 DS board support
powerpc/fsl-booke64: Use TLB CAMs to cover linear mapping on FSL 64-bit chips
powerpc/fsl-booke: Add support for FSL Arch v1.0 MMU in setup_page_sizes
powerpc/fsl-booke: Add support for FSL 64-bit e5500 core
powerpc/85xx: add cache-sram support
powerpc/85xx: add ngPIXIS FPGA device tree node to the P1022DS board
powerpc: Fix compile error with paca code on ppc64e
powerpc/fsl-booke: Add p3041 DS board support
oprofile/fsl emb: Don't set MSR[PMM] until after clearing the interrupt.
powerpc/fsl-booke: Add PCI device ids for P2040/P3041/P5010/P5020 QoirQ chips
powerpc/mpc8xxx_gpio: Add support for 'qoriq-gpio' controllers
powerpc/fsl_booke: Add support to boot from core other than 0
powerpc/p1022: Add probing for individual DMA channels
powerpc/fsl_soc: Search all global-utilities nodes for rstccr
powerpc: Fix invalid page flags in create TLB CAM path for PTE_64BIT
powerpc/mpc83xx: Support for MPC8308 P1M board
...
Fix up conflict with the generic irq_work changes in arch/powerpc/kernel/time.c
|
|
* 'core-memblock-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (74 commits)
x86-64: Only set max_pfn_mapped to 512 MiB if we enter via head_64.S
xen: Cope with unmapped pages when initializing kernel pagetable
memblock, bootmem: Round pfn properly for memory and reserved regions
memblock: Annotate memblock functions with __init_memblock
memblock: Allow memblock_init to be called early
memblock/arm: Fix memblock_region_is_memory() typo
x86, memblock: Remove __memblock_x86_find_in_range_size()
memblock: Fix wraparound in find_region()
x86-32, memblock: Make add_highpages honor early reserved ranges
x86, memblock: Fix crashkernel allocation
arm, memblock: Fix the sparsemem build
memblock: Fix section mismatch warnings
powerpc, memblock: Fix memblock API change fallout
memblock, microblaze: Fix memblock API change fallout
x86: Remove old bootmem code
x86, memblock: Use memblock_memory_size()/memblock_free_memory_size() to get correct dma_reserve
x86: Remove not used early_res code
x86, memblock: Replace e820_/_early string with memblock_
x86: Use memblock to replace early_res
x86, memblock: Use memblock_debug to control debug message print out
...
Fix up trivial conflicts in arch/x86/kernel/setup.c and kernel/Makefile
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-irqflags:
Fix IRQ flag handling naming
MIPS: Add missing #inclusions of <linux/irq.h>
smc91x: Add missing #inclusion of <linux/irq.h>
Drop a couple of unnecessary asm/system.h inclusions
SH: Add missing consts to sys_execve() declaration
Blackfin: Rename IRQ flags handling functions
Blackfin: Add missing dep to asm/irqflags.h
Blackfin: Rename DES PC2() symbol to avoid collision
Blackfin: Split the BF532 BFIN_*_FIO_FLAG() functions to their own header
Blackfin: Split PLL code from mach-specific cdef headers
|
|
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (29 commits)
sched: Export account_system_vtime()
sched: Call tick_check_idle before __irq_enter
sched: Remove irq time from available CPU power
sched: Do not account irq time to current task
x86: Add IRQ_TIME_ACCOUNTING
sched: Add IRQ_TIME_ACCOUNTING, finer accounting of irq time
sched: Add a PF flag for ksoftirqd identification
sched: Consolidate account_system_vtime extern declaration
sched: Fix softirq time accounting
sched: Drop group_capacity to 1 only if local group has extra capacity
sched: Force balancing on newidle balance if local group has capacity
sched: Set group_imb only a task can be pulled from the busiest cpu
sched: Do not consider SCHED_IDLE tasks to be cache hot
sched: Drop all load weight manipulation for RT tasks
sched: Create special class for stop/migrate work
sched: Unindent labels
sched: Comment updates: fix default latency and granularity numbers
tracing/sched: Add sched_pi_setprio tracepoint
sched: Give CPU bound RT tasks preference
sched: Try not to migrate higher priority RT tasks
...
|
|
Just a minor cleanup patch that makes things easier to the following patches.
No functionality change in this patch.
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1286237003-12406-3-git-send-email-venki@google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Provide a mechanism that allows running code in IRQ context. It is
most useful for NMI code that needs to interact with the rest of the
system -- like wakeup a task to drain buffers.
Perf currently has such a mechanism, so extract that and provide it as
a generic feature, independent of perf so that others may also
benefit.
The IRQ context callback is generated through self-IPIs where
possible, or on architectures like powerpc the decrementer (the
built-in timer facility) is set to generate an interrupt immediately.
Architectures that don't have anything like this get to do with a
callback from the timer tick. These architectures can call
irq_work_run() at the tail of any IRQ handlers that might enqueue such
work (like the perf IRQ handler) to avoid undue latencies in
processing the work.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[ various fixes ]
Signed-off-by: Huang Ying <ying.huang@intel.com>
LKML-Reference: <1287036094.7768.291.camel@yhuang-dev>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The patch below updates broken web addresses in the arch directory.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Update setup_page_sizes() to support for a MMU v1.0 FSL style MMU
implementation. In such a processor, we don't have TLB0PS or EPTCFG
registers (and access to these registers may cause exceptions). We need
to parse the older format of TLBnCFG for page size support. Additionaly,
assume since we are an FSL implementation that we have 2 TLB arrays and
the second array contains the variable size pages.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
It adds cache-sram support in P1/P2 QorIQ platforms as under:
* A small abstraction over powerpc's remote heap allocator
* Exports mpc85xx_cache_sram_alloc()/free() APIs
* Supports only one contiguous SRAM window
* Drivers can do the following in Kconfig to use these APIs
"select FSL_85XX_CACHE_SRAM if MPC85xx"
* Required SRAM size and the offset where SRAM should be mapped must be
provided at kernel command line as :
cache-sram-size=<value>
cache-sram-offset=<offset>
Signed-off-by: Harninder Rai <harninder.rai@freescale.com>
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
There exists a four line chunk of code, which when configured for
64 bit address space, can incorrectly set certain page flags during
the TLB creation. It turns out that this is code which isn't used,
but might still serve a purpose. Since it isn't obvious why it exists
or why it causes problems, the below description covers both in detail.
For powerpc bootstrap, the physical memory (at most 768M), is mapped
into the kernel space via the following path:
MMU_init()
|
+ adjust_total_lowmem()
|
+ map_mem_in_cams()
|
+ settlbcam(i, virt, phys, cam_sz, PAGE_KERNEL_X, 0);
On settlbcam(), the kernel will create TLB entries according to the flag,
PAGE_KERNEL_X.
settlbcam()
{
...
TLBCAM[index].MAS1 = MAS1_VALID
| MAS1_IPROT | MAS1_TSIZE(tsize) | MAS1_TID(pid);
^
These entries cannot be invalidated by the
kernel since MAS1_IPROT is set on TLB property.
...
if (flags & _PAGE_USER) {
TLBCAM[index].MAS3 |= MAS3_UX | MAS3_UR;
TLBCAM[index].MAS3 |= ((flags & _PAGE_RW) ? MAS3_UW : 0);
}
For classic BookE (flags & _PAGE_USER) is 'zero' so it's fine.
But on boards like the the Freescale P4080, we want to support 36-bit
physical address on it. So the following options may be set:
CONFIG_FSL_BOOKE=y
CONFIG_PTE_64BIT=y
CONFIG_PHYS_64BIT=y
As a result, boards like the P4080 will introduce PTE format as Book3E.
As per the file: arch/powerpc/include/asm/pgtable-ppc32.h
* #elif defined(CONFIG_FSL_BOOKE) && defined(CONFIG_PTE_64BIT)
* #include <asm/pte-book3e.h>
So PAGE_KERNEL_X is __pgprot(_PAGE_BASE | _PAGE_KERNEL_RWX) and the
book3E version of _PAGE_KERNEL_RWX is defined with:
(_PAGE_BAP_SW | _PAGE_BAP_SR | _PAGE_DIRTY | _PAGE_BAP_SX)
Note the _PAGE_BAP_SR, which is also defined in the book3E _PAGE_USER:
#define _PAGE_USER (_PAGE_BAP_UR | _PAGE_BAP_SR) /* Can be read */
So the possibility exists to wrongly assign the user MAS3_U<RWX> bits
to kernel (PAGE_KERNEL_X) address space via the following code fragment:
if (flags & _PAGE_USER) {
TLBCAM[index].MAS3 |= MAS3_UX | MAS3_UR;
TLBCAM[index].MAS3 |= ((flags & _PAGE_RW) ? MAS3_UW : 0);
}
Here is a dump of the TLB info from Simics with the above code present:
------
L2 TLB1
GT SSS UUU V I
Row Logical Physical SS TLPID TID WIMGE XWR XWR F P V
----- ----------------- ------------------- -- ----- ----- ----- --- --- - - -
0 c0000000-cfffffff 000000000-00fffffff 00 0 0 M XWR XWR 0 1 1
1 d0000000-dfffffff 010000000-01fffffff 00 0 0 M XWR XWR 0 1 1
2 e0000000-efffffff 020000000-02fffffff 00 0 0 M XWR XWR 0 1 1
Actually this conditional code was used for two legacy functions:
1: support KGDB to set break point.
KGDB already dropped this; now uses its core write to set break point.
2: io_block_mapping() to create TLB in segmentation size (not PAGE_SIZE)
for device IO space.
This use case is also removed from the latest PowerPC kernel.
However, there may still be a use case for it in the future, like
large user pages, so we can't remove it entirely. As an alternative,
we match on all bits of _PAGE_USER instead of just any bits, so the
case where just _PAGE_BAP_SR is set can't sneak through.
With this done, the TLB appears without U having XWR as below:
-------
L2 TLB1
GT SSS UUU V I
Row Logical Physical SS TLPID TID WIMGE XWR XWR F P V
----- ----------------- ------------------- -- ----- ----- ----- --- --- - - -
0 c0000000-cfffffff 000000000-00fffffff 00 0 0 M XWR 0 1 1
1 d0000000-dfffffff 010000000-01fffffff 00 0 0 M XWR 0 1 1
2 e0000000-efffffff 020000000-02fffffff 00 0 0 M XWR 0 1 1
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Right now just the kexec crash pathway turns turns off the interrupts.
Pull that out and make a generic version for use elsewhere
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
BUID_HI and BUID_LO are used to pass data to call_rtas, which expects
ints or u32s. But the macro doesn't cast the return, so the result is
still u64. Use the upper_32_bits and lower_32_bits macros that have been
added to kernel.h.
Found by getting printf format errors trying to debug print the args, no
actual code change for 64 bit kernels where the macros are actually
used.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Export the rtas_ibm_suspend_me() routine. This is needed to perform
partition migration in the kernel.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
|
|
Merge reason: Update from -rc3 to -rc7.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Now that the generic DMAEngine API has support for scatterlist to
scatterlist copying, the device_prep_slave_sg() portion of the
DMA_SLAVE API is no longer necessary and has been removed.
However, the device_control() portion of the DMA_SLAVE API is still
useful to control device specific parameters, such as externally
controlled DMA transfers and maximum burst length.
A special dma_ctrl_cmd has been added to enable externally controlled
DMA transfers. This is currently specific to the Freescale DMA
controller, but can easily be made generic when another user is found.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Fix the IRQ flag handling naming. In linux/irqflags.h under one configuration,
it maps:
local_irq_enable() -> raw_local_irq_enable()
local_irq_disable() -> raw_local_irq_disable()
local_irq_save() -> raw_local_irq_save()
...
and under the other configuration, it maps:
raw_local_irq_enable() -> local_irq_enable()
raw_local_irq_disable() -> local_irq_disable()
raw_local_irq_save() -> local_irq_save()
...
This is quite confusing. There should be one set of names expected of the
arch, and this should be wrapped to give another set of names that are expected
by users of this facility.
Change this to have the arch provide:
flags = arch_local_save_flags()
flags = arch_local_irq_save()
arch_local_irq_restore(flags)
arch_local_irq_disable()
arch_local_irq_enable()
arch_irqs_disabled_flags(flags)
arch_irqs_disabled()
arch_safe_halt()
Then linux/irqflags.h wraps these to provide:
raw_local_save_flags(flags)
raw_local_irq_save(flags)
raw_local_irq_restore(flags)
raw_local_irq_disable()
raw_local_irq_enable()
raw_irqs_disabled_flags(flags)
raw_irqs_disabled()
raw_safe_halt()
with type checking on the flags 'arguments', and then wraps those to provide:
local_save_flags(flags)
local_irq_save(flags)
local_irq_restore(flags)
local_irq_disable()
local_irq_enable()
irqs_disabled_flags(flags)
irqs_disabled()
safe_halt()
with tracing included if enabled.
The arch functions can now all be inline functions rather than some of them
having to be macros.
Signed-off-by: David Howells <dhowells@redhat.com> [X86, FRV, MN10300]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> [Tile]
Signed-off-by: Michal Simek <monstr@monstr.eu> [Microblaze]
Tested-by: Catalin Marinas <catalin.marinas@arm.com> [ARM]
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> [AVR]
Acked-by: Tony Luck <tony.luck@intel.com> [IA-64]
Acked-by: Hirokazu Takata <takata@linux-m32r.org> [M32R]
Acked-by: Greg Ungerer <gerg@uclinux.org> [M68K/M68KNOMMU]
Acked-by: Ralf Baechle <ralf@linux-mips.org> [MIPS]
Acked-by: Kyle McMartin <kyle@mcmartin.ca> [PA-RISC]
Acked-by: Paul Mackerras <paulus@samba.org> [PowerPC]
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [S390]
Acked-by: Chen Liqin <liqin.chen@sunplusct.com> [Score]
Acked-by: Matt Fleming <matt@console-pimps.org> [SH]
Acked-by: David S. Miller <davem@davemloft.net> [Sparc]
Acked-by: Chris Zankel <chris@zankel.net> [Xtensa]
Reviewed-by: Richard Henderson <rth@twiddle.net> [Alpha]
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp> [H8300]
Cc: starvik@axis.com [CRIS]
Cc: jesper.nilsson@axis.com [CRIS]
Cc: linux-cris-kernel@axis.com
|
|
compat_alloc_user_space() expects the caller to independently call
access_ok() to verify the returned area. A missing call could
introduce problems on some architectures.
This patch incorporates the access_ok() check into
compat_alloc_user_space() and also adds a sanity check on the length.
The existing compat_alloc_user_space() implementations are renamed
arch_compat_alloc_user_space() and are used as part of the
implementation of the new global function.
This patch assumes NULL will cause __get_user()/__put_user() to either
fail or access userspace on all architectures. This should be
followed by checking the return value of compat_access_user_space()
for NULL in the callers, at which time the access_ok() in the callers
can also be removed.
Reported-by: Ben Hawkes <hawkes@sota.gen.nz>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: James Bottomley <jejb@parisc-linux.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: <stable@kernel.org>
|
|
The slab.h header is required to use the kmalloc() family of functions.
Due to recent kernel changes, this header must be directly included by
code that calls into the memory allocator.
Without this patch, any code which includes this header fails to build.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch wires up the various socket system calls on PowerPC so that
userspace can call them directly, rather than by going through the
multiplexed socketcall system call.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Some platforms may want to override dma_set_mask() to take into
account some specific "features" such as the availability of
a direct-map window in addition to an iommu.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This patch removes all explicit tests for the TIF_32BIT flag
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Neither lfs nor stfs touch the fpscr, so remove the restore/save of it
around them.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Since the cpu accounting code uses the hypervisor dispatch trace log
now when CONFIG_VIRT_CPU_ACCOUNTING = y, the previous commit disabled
access to it via files in the /sys/kernel/debug/powerpc/dtl/ directory
in that case. This restores those files.
To do this, we now have a hook that the cpu accounting code will call
as it processes each entry from the hypervisor dispatch trace log.
The code in dtl.c now uses that to fill up its ring buffer, rather
than having the hypervisor fill the ring buffer directly.
This also fixes dtl_file_read() to handle overflow conditions a bit
better and adds a spinlock to ensure that race conditions (multiple
processes opening or reading the file concurrently) are handled
correctly.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Currently, when CONFIG_VIRT_CPU_ACCOUNTING is enabled, we use the
PURR register for measuring the user and system time used by
processes, as well as other related times such as hardirq and
softirq times. This turns out to be quite confusing for users
because it means that a program will often be measured as taking
less time when run on a multi-threaded processor (SMT2 or SMT4 mode)
than it does when run on a single-threaded processor (ST mode), even
though the program takes longer to finish. The discrepancy is
accounted for as stolen time, which is also confusing, particularly
when there are no other partitions running.
This changes the accounting to use the timebase instead, meaning that
the reported user and system times are the actual number of real-time
seconds that the program was executing on the processor thread,
regardless of which SMT mode the processor is in. Thus a program will
generally show greater user and system times when run on a
multi-threaded processor than on a single-threaded processor.
On pSeries systems on POWER5 or later processors, we measure the
stolen time (time when this partition wasn't running) using the
hypervisor dispatch trace log. We check for new entries in the
log on every entry from user mode and on every transition from
kernel process context to soft or hard IRQ context (i.e. when
account_system_vtime() gets called). So that we can correctly
distinguish time stolen from user time and time stolen from system
time, without having to check the log on every exit to user mode,
we store separate timestamps for exit to user mode and entry from
user mode.
On systems that have a SPURR (POWER6 and POWER7), we read the SPURR
in account_system_vtime() (as before), and then apportion the SPURR
ticks since the last time we read it between scaled user time and
scaled system time according to the relative proportions of user
time and system time over the same interval. This avoids having to
read the SPURR on every kernel entry and exit. On systems that have
PURR but not SPURR (i.e., POWER5), we do the same using the PURR
rather than the SPURR.
This disables the DTL user interface in /sys/debug/kernel/powerpc/dtl
for now since it conflicts with the use of the dispatch trace log
by the time accounting code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This arranges for the lppaca structs for most cpus to be dynamically
allocated in the same manner as the paca structs. If we don't include
support for legacy iSeries, only the first lppaca is statically
allocated; the rest are dynamically allocated. If we include legacy
iSeries support, then we statically allocate the first 64 lppaca
structs, since the iSeries hypervisor requires that the lppaca
structs be present in the data section of the kernel image, but
legacy iSeries supports at most 64 cpus.
With CONFIG_NR_CPUS, the kernel image size for a typical pSeries config
went from:
text data bss dec hex filename
9524478 4734564 8469944 22728986 15ad11a ../test-1024/vmlinux
to:
text data bss dec hex filename
9524482 3751508 8469944 21745934 14bd10e ../test-1024/vmlinux
a reduction of 983052 bytes overall.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Currently we have the lppaca structs as a simple array of NR_CPUS
entries, taking up space in the data section of the kernel image.
In future we would like to allocate them dynamically, so this
abstracts out the accesses to the array, making it easier to
change how we locate the lppaca for a given cpu in future.
Specifically, lppaca[cpu] changes to lppaca_of(cpu).
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The POWER architecture does not require stcx to check that it is operating
on the same address as the larx. This means it is possible for an
an exception handler to execute a larx, get a reservation, decide
not to do the stcx and then return back with an active reservation. If the
interrupted code was in the middle of a larx/stcx sequence the stcx could
incorrectly succeed.
All recent POWER CPUs check the address before letting the stcx succeed
so we can create a CPU feature and nop it out. As Ben suggested, we can
only do this in our syscall path because there is a remote possibility
some kernel code gets interrupted by an exception that ends up operating
on the same cacheline.
Thanks to Paul Mackerras and Derek Williams for the idea.
To test this I used a very simple null syscall (actually getppid) testcase
at http://ozlabs.org/~anton/junkcode/null_syscall.c
I tested against 2.6.35-git10 with the following changes against the
pseries_defconfig:
CONFIG_VIRT_CPU_ACCOUNTING=n
CONFIG_AUDIT=n
CONFIG_PPC_4K_PAGES=n
CONFIG_PPC_64K_PAGES=y
CONFIG_FORCE_MAX_ZONEORDER=9
CONFIG_PPC_SUBPAGE_PROT=n
CONFIG_FUNCTION_TRACER=n
CONFIG_FUNCTION_GRAPH_TRACER=n
CONFIG_IRQSOFF_TRACER=n
CONFIG_STACK_TRACER=n
to remove the overhead of virtual CPU accounting, syscall auditing and
the ftrace mcount tracers. 64kB pages were enabled to minimise TLB misses.
POWER6: +8.2%
POWER7: +7.0%
Another suggestion was to use a larx to something in the L1 instead of a stcx.
This was almost as fast as removing the larx on POWER6, but only 3.5% faster
on POWER7. We can use this to speed up the reservation clear in our
exception exit code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This adds the equivalent of csum_and_copy_from_user for the receive side so we
can copy and checksum in one pass. It is modelled on the generic checksum
routine.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We use the same core loop as the new csum_partial, adding in the
stores and exception handling code. To keep things simple we do all the
exception fixup in csum_and_copy_from_user. This wrapper function is
modelled on the generic checksum code and is careful to always calculate
a complete checksum even if we only copied part of the data to userspace.
To test this I forced checksumming on over loopback and ran socklib (a
simple TCP benchmark). On a POWER6 575 throughput improved by 19% with
this patch. If I forced both the sender and receiver onto the same cpu
(with the hope of shifting the benchmark from being cache bandwidth limited
to cpu limited), adding this patch improved performance by 55%
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Conflicts:
arch/x86/kernel/trampoline.c
mm/memblock.c
Merge reason: Resolve the conflicts, update to latest upstream.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
I'm sick of seeing ppc64_runlatch_off in our profiles, so inline it
into the callers. To avoid a mess of circular includes I didn't add
it as an inline function.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The code is wrapped in an #if 0, but it's wrong so we may as well fix it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This makes the 64-bit kernel use 64-bit signed integers for the counter
(effectively supporting 32-bit of active count in the semaphore), thus
avoiding things like overflow of the mmap_sem if you use a really crazy
number of threads
Note: Ideally the type in the structure should be atomic_long_t rather
than "long". However, there's some nasty issues with that. It needs to
be initialized statically -and- lib/rwsem.c does things like
sem->count = RWSEM_UNLOCKED_VALUE;
Now, if you mix in the fact that atomic_* types are actually structures
with one member and note typedefs of a scalar, it makes its really nasty.
So I stuck to what we did before using a long and casts for now.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Fairly simple conflicts, the most serious ones are the i.MX ones which I
suspect now need another rename.
Conflicts:
arch/arm/mach-mx2/clock_imx27.c
arch/arm/mach-mx2/devices.c
arch/arm/mach-omap2/board-rx51-peripherals.c
arch/arm/mach-omap2/board-zoom2.c
sound/soc/fsl/mpc5200_dma.c
sound/soc/fsl/mpc5200_dma.h
sound/soc/fsl/mpc8610_hpcd.c
sound/soc/pxa/spitz.c
|
|
unifdef-y and header-y have same semantic, so drop unifdef-y
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
|
|
The immap_86xx.h header file only defines one data structure: the "global
utilities" register set found on Freescale PowerPC SOCs. Rename this file
to fsl_guts.h to reflect its true purpose, and extend it to cover the "GUTS"
register set on 85xx chips.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
Architectures implement dma_is_consistent() in different ways (some
misinterpret the definition of API in DMA-API.txt). So it hasn't been so
useful for drivers. We have only one user of the API in tree. Unlikely
out-of-tree drivers use the API.
Even if we fix dma_is_consistent() in some architectures, it doesn't look
useful at all. It was invented long ago for some old systems that can't
allocate coherent memory at all. It's better to export only APIs that are
definitely necessary for drivers.
Let's remove this API.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
Alexander Graf
Linus Torvalds
Venkatesh Pallipadi
Peter Zijlstra
Justin P. Mattock
Kumar Gala
Harninder Rai
Paul Gortmaker
Matthew McClintock
Nishanth Aravamudan
Nathan Fontenot
Benjamin Herrenschmidt
Ingo Molnar
Ira Snyder
David Howells
H. Peter Anvin
Ian Munsie
Denis Kirjanov
Andreas Schwab
Paul Mackerras
Anton Blanchard
Mark Brown
Sam Ravnborg
Timur Tabi
FUJITA Tomonori