| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull networking updates from David Miller:
"Most notable changes in here:
1) By far the biggest accomplishment, thanks to a large range of
contributors, is the addition of multi-send for transmit. This is
the result of discussions back in Chicago, and the hard work of
several individuals.
Now, when the ->ndo_start_xmit() method of a driver sees
skb->xmit_more as true, it can choose to defer the doorbell
telling the driver to start processing the new TX queue entires.
skb->xmit_more means that the generic networking is guaranteed to
call the driver immediately with another SKB to send.
There is logic added to the qdisc layer to dequeue multiple
packets at a time, and the handling mis-predicted offloads in
software is now done with no locks held.
Finally, pktgen is extended to have a "burst" parameter that can
be used to test a multi-send implementation.
Several drivers have xmit_more support: i40e, igb, ixgbe, mlx4,
virtio_net
Adding support is almost trivial, so export more drivers to
support this optimization soon.
I want to thank, in no particular or implied order, Jesper
Dangaard Brouer, Eric Dumazet, Alexander Duyck, Tom Herbert, Jamal
Hadi Salim, John Fastabend, Florian Westphal, Daniel Borkmann,
David Tat, Hannes Frederic Sowa, and Rusty Russell.
2) PTP and timestamping support in bnx2x, from Michal Kalderon.
3) Allow adjusting the rx_copybreak threshold for a driver via
ethtool, and add rx_copybreak support to enic driver. From
Govindarajulu Varadarajan.
4) Significant enhancements to the generic PHY layer and the bcm7xxx
driver in particular (EEE support, auto power down, etc.) from
Florian Fainelli.
5) Allow raw buffers to be used for flow dissection, allowing drivers
to determine the optimal "linear pull" size for devices that DMA
into pools of pages. The objective is to get exactly the
necessary amount of headers into the linear SKB area pre-pulled,
but no more. The new interface drivers use is eth_get_headlen().
From WANG Cong, with driver conversions (several had their own
by-hand duplicated implementations) by Alexander Duyck and Eric
Dumazet.
6) Support checksumming more smoothly and efficiently for
encapsulations, and add "foo over UDP" facility. From Tom
Herbert.
7) Add Broadcom SF2 switch driver to DSA layer, from Florian
Fainelli.
8) eBPF now can load programs via a system call and has an extensive
testsuite. Alexei Starovoitov and Daniel Borkmann.
9) Major overhaul of the packet scheduler to use RCU in several major
areas such as the classifiers and rate estimators. From John
Fastabend.
10) Add driver for Intel FM10000 Ethernet Switch, from Alexander
Duyck.
11) Rearrange TCP_SKB_CB() to reduce cache line misses, from Eric
Dumazet.
12) Add Datacenter TCP congestion control algorithm support, From
Florian Westphal.
13) Reorganize sk_buff so that __copy_skb_header() is significantly
faster. From Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1558 commits)
netlabel: directly return netlbl_unlabel_genl_init()
net: add netdev_txq_bql_{enqueue, complete}_prefetchw() helpers
net: description of dma_cookie cause make xmldocs warning
cxgb4: clean up a type issue
cxgb4: potential shift wrapping bug
i40e: skb->xmit_more support
net: fs_enet: Add NAPI TX
net: fs_enet: Remove non NAPI RX
r8169:add support for RTL8168EP
net_sched: copy exts->type in tcf_exts_change()
wimax: convert printk to pr_foo()
af_unix: remove 0 assignment on static
ipv6: Do not warn for informational ICMP messages, regardless of type.
Update Intel Ethernet Driver maintainers list
bridge: Save frag_max_size between PRE_ROUTING and POST_ROUTING
tipc: fix bug in multicast congestion handling
net: better IFF_XMIT_DST_RELEASE support
net/mlx4_en: remove NETDEV_TX_BUSY
3c59x: fix bad split of cpu_to_le32(pci_map_single())
net: bcmgenet: fix Tx ring priority programming
...
|
|
Pull KVM updates from Paolo Bonzini:
"Fixes and features for 3.18.
Apart from the usual cleanups, here is the summary of new features:
- s390 moves closer towards host large page support
- PowerPC has improved support for debugging (both inside the guest
and via gdbstub) and support for e6500 processors
- ARM/ARM64 support read-only memory (which is necessary to put
firmware in emulated NOR flash)
- x86 has the usual emulator fixes and nested virtualization
improvements (including improved Windows support on Intel and
Jailhouse hypervisor support on AMD), adaptive PLE which helps
overcommitting of huge guests. Also included are some patches that
make KVM more friendly to memory hot-unplug, and fixes for rare
caching bugs.
Two patches have trivial mm/ parts that were acked by Rik and Andrew.
Note: I will soon switch to a subkey for signing purposes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (157 commits)
kvm: do not handle APIC access page if in-kernel irqchip is not in use
KVM: s390: count vcpu wakeups in stat.halt_wakeup
KVM: s390/facilities: allow TOD-CLOCK steering facility bit
KVM: PPC: BOOK3S: HV: CMA: Reserve cma region only in hypervisor mode
arm/arm64: KVM: Report correct FSC for unsupported fault types
arm/arm64: KVM: Fix VTTBR_BADDR_MASK and pgd alloc
kvm: Fix kvm_get_page_retry_io __gup retval check
arm/arm64: KVM: Fix set_clear_sgi_pend_reg offset
kvm: x86: Unpin and remove kvm_arch->apic_access_page
kvm: vmx: Implement set_apic_access_page_addr
kvm: x86: Add request bit to reload APIC access page address
kvm: Add arch specific mmu notifier for page invalidation
kvm: Rename make_all_cpus_request() to kvm_make_all_cpus_request() and make it non-static
kvm: Fix page ageing bugs
kvm/x86/mmu: Pass gfn and level to rmapp callback.
x86: kvm: use alternatives for VMCALL vs. VMMCALL if kernel text is read-only
kvm: x86: use macros to compute bank MSRs
KVM: x86: Remove debug assertion of non-PAE reserved bits
kvm: don't take vcpu mutex for obviously invalid vcpu ioctls
kvm: Faults which trigger IO release the mmap_sem
...
|
|
Pull "trivial tree" updates from Jiri Kosina:
"Usual pile from trivial tree everyone is so eagerly waiting for"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
Remove MN10300_PROC_MN2WS0038
mei: fix comments
treewide: Fix typos in Kconfig
kprobes: update jprobe_example.c for do_fork() change
Documentation: change "&" to "and" in Documentation/applying-patches.txt
Documentation: remove obsolete pcmcia-cs from Changes
Documentation: update links in Changes
Documentation: Docbook: Fix generated DocBook/kernel-api.xml
score: Remove GENERIC_HAS_IOMAP
gpio: fix 'CONFIG_GPIO_IRQCHIP' comments
tty: doc: Fix grammar in serial/tty
dma-debug: modify check_for_stack output
treewide: fix errors in printk
genirq: fix reference in devm_request_threaded_irq comment
treewide: fix synchronize_rcu() in comments
checkstack.pl: port to AArch64
doc: queue-sysfs: minor fixes
init/do_mounts: better syntax description
MIPS: fix comment spelling
powerpc/simpleboot: fix comment
...
|
|
We use cma reserved area for creating guest hash page table.
Don't do the reservation in non-hypervisor mode. This avoids unnecessary
CMA reservation when booting with limited memory configs like
fadump and kdump.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Patch queue for ppc - 2014-09-24
New awesome things in this release:
- E500: e6500 core support
- E500: guest and remote debug support
- Book3S: remote sw breakpoint support
- Book3S: HV: Minor bugfixes
Alexander Graf (1):
KVM: PPC: Pass enum to kvmppc_get_last_inst
Bharat Bhushan (8):
KVM: PPC: BOOKE: allow debug interrupt at "debug level"
KVM: PPC: BOOKE : Emulate rfdi instruction
KVM: PPC: BOOKE: Allow guest to change MSR_DE
KVM: PPC: BOOKE: Clear guest dbsr in userspace exit KVM_EXIT_DEBUG
KVM: PPC: BOOKE: Guest and hardware visible debug registers are same
KVM: PPC: BOOKE: Add one reg interface for DBSR
KVM: PPC: BOOKE: Add one_reg documentation of SPRG9 and DBSR
KVM: PPC: BOOKE: Emulate debug registers and exception
Madhavan Srinivasan (2):
powerpc/kvm: support to handle sw breakpoint
powerpc/kvm: common sw breakpoint instr across ppc
Michael Neuling (1):
KVM: PPC: Book3S HV: Add register name when loading toc
Mihai Caraman (10):
powerpc/booke: Restrict SPE exception handlers to e200/e500 cores
powerpc/booke: Revert SPE/AltiVec common defines for interrupt numbers
KVM: PPC: Book3E: Increase FPU laziness
KVM: PPC: Book3e: Add AltiVec support
KVM: PPC: Make ONE_REG powerpc generic
KVM: PPC: Move ONE_REG AltiVec support to powerpc
KVM: PPC: Remove the tasklet used by the hrtimer
KVM: PPC: Remove shared defines for SPE and AltiVec interrupts
KVM: PPC: e500mc: Add support for single threaded vcpus on e6500 core
KVM: PPC: Book3E: Enable e6500 core
Paul Mackerras (2):
KVM: PPC: Book3S HV: Increase timeout for grabbing secondary threads
KVM: PPC: Book3S HV: Only accept host PVR value for guest PVR
|
|
|
|
Commit df568d8e ("scsi: Use 'depends' with LIBFC instead of
'select'.") removed what happened to be the only instance of 'select
NET'. Defconfigs that were relying on the select now lack networking
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This will be used to let the guest run while the APIC access page is
not pinned. Because subsequent patches will fill in the function
for x86, place the (still empty) x86 implementation in the x86.c file
instead of adding an inline function in kvm_host.h.
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
1. We were calling clear_flush_young_notify in unmap_one, but we are
within an mmu notifier invalidate range scope. The spte exists no more
(due to range_start) and the accessed bit info has already been
propagated (due to kvm_pfn_set_accessed). Simply call
clear_flush_young.
2. We clear_flush_young on a primary MMU PMD, but this may be mapped
as a collection of PTEs by the secondary MMU (e.g. during log-dirty).
This required expanding the interface of the clear_flush_young mmu
notifier, so a lot of code has been trivially touched.
3. In the absence of shadow_accessed_mask (e.g. EPT A bit), we emulate
the access bit by blowing the spte. This requires proper synchronizing
with MMU notifier consumers, like every other removal of spte's does.
Signed-off-by: Andres Lagar-Cavilla <andreslc@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The kvmppc_get_last_inst function recently received a facelift that allowed
us to pass an enum of the type of instruction we want to read into it rather
than an unreadable boolean.
Unfortunately, not all callers ended up passing the enum. This wasn't really
an issue as "true" and "false" happen to match the two enum values we have,
but it's still hard to read.
Update all callers of kvmppc_get_last_inst() to follow the new calling
convention.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This patch extends the use of illegal instruction as software
breakpoint instruction across the ppc platform. Patch extends
booke program interrupt code to support software breakpoint.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
[agraf: Fix bookehv]
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This patch adds kernel side support for software breakpoint.
Design is that, by using an illegal instruction, we trap to hypervisor
via Emulation Assistance interrupt, where we check for the illegal instruction
and accordingly we return to Host or Guest. Patch also adds support for
software breakpoint in PR KVM.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Now that AltiVec and hardware thread support is in place enable e6500 core.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
ePAPR represents hardware threads as cpu node properties in device tree.
So with existing QEMU, hardware threads are simply exposed as vcpus with
one hardware thread.
The e6500 core shares TLBs between hardware threads. Without tlb write
conditional instruction, the Linux kernel uses per core mechanisms to
protect against duplicate TLB entries.
The guest is unable to detect real siblings threads, so it can't use the
TLB protection mechanism. An alternative solution is to use the hypervisor
to allocate different lpids to guest's vcpus that runs simultaneous on real
siblings threads. On systems with two threads per core this patch halves
the size of the lpid pool that the allocator sees and use two lpids per VM.
Use even numbers to speedup vcpu lpid computation with consecutive lpids
per VM: vm1 will use lpids 2 and 3, vm2 lpids 4 and 5, and so on.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: fix spelling]
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Since the guest can read the machine's PVR (Processor Version Register)
directly and see the real value, we should disallow userspace from
setting any value for the guest's PVR other than the real host value.
Therefore this makes kvm_arch_vcpu_set_sregs_hv() check the supplied
PVR value and return an error if it is different from the host value,
which has been put into vcpu->arch.pvr at vcpu creation time.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Occasional failures have been seen with split-core mode and migration
where the message "KVM: couldn't grab cpu" appears. This increases
the length of time that we wait from 1ms to 10ms, which seems to
work around the issue.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
We currently decide at compile-time which of the SPE or AltiVec units to
support exclusively. Guard kernel defines with CONFIG_SPE_POSSIBLE and
CONFIG_PPC_E500MC and remove shared defines.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Powerpc timer implementation is a copycat version of s390. Now that they removed
the tasklet with commit ea74c0ea1b24a6978a6ebc80ba4dbc7b7848b32d follow this
optimization.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This patch emulates debug registers and debug exception
to support guest using debug resource. This enables running
gdb/kgdb etc in guest.
On BOOKE architecture we cannot share debug resources between QEMU and
guest because:
When QEMU is using debug resources then debug exception must
be always enabled. To achieve this we set MSR_DE and also set
MSRP_DEP so guest cannot change MSR_DE.
When emulating debug resource for guest we want guest
to control MSR_DE (enable/disable debug interrupt on need).
So above mentioned two configuration cannot be supported
at the same time. So the result is that we cannot share
debug resources between QEMU and Guest on BOOKE architecture.
In the current design QEMU gets priority over guest, this means that if
QEMU is using debug resources then guest cannot use them and if guest is
using debug resource then QEMU can overwrite them.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Move ONE_REG AltiVec support to powerpc generic layer.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Make ONE_REG generic for server and embedded architectures by moving
kvm_vcpu_ioctl_get_one_reg() and kvm_vcpu_ioctl_set_one_reg() functions
to powerpc layer.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Add AltiVec support in KVM for Book3e. FPU support gracefully reuse host
infrastructure so follow the same approach for AltiVec.
Book3e specification defines shared interrupt numbers for SPE and AltiVec
units. Still SPE is present in e200/e500v2 cores while AltiVec is present in
e6500 core. So we can currently decide at compile-time which of the SPE or
AltiVec units to support exclusively by using CONFIG_SPE_POSSIBLE and
CONFIG_PPC_E500MC defines. As Alexander Graf suggested, keep SPE and AltiVec
exception handlers distinct to improve code readability.
Guests have the privilege to enable AltiVec, so we always need to support
AltiVec in KVM and implicitly in host to reflect interrupts and to save/restore
the unit context. KVM will be loaded on cores with AltiVec unit only if
CONFIG_ALTIVEC is defined. Use this define to guard KVM AltiVec logic.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Increase FPU laziness by loading the guest state into the unit before entering
the guest instead of doing it on each vcpu schedule. Without this improvement
an interrupt may claim floating point corrupting guest state.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Add 'r' to register name r2 in kvmppc_hv_enter.
Also update comment at the top of kvmppc_hv_enter to indicate that R2/TOC is
non-volatile.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Book3E specification defines shared interrupt numbers for SPE and AltiVec
units. Still SPE is present in e200/e500v2 cores while AltiVec is present in
e6500 core. So we can currently decide at compile-time which unit to support
exclusively. As Alexander Graf suggested, this will improve code readability
especially in KVM.
Use distinct defines to identify SPE/AltiVec interrupt numbers, reverting
c58ce397 and 6b310fc5 patches that added common defines.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
SPE exception handlers are now defined for 32-bit e500mc cores even though
SPE unit is not present and CONFIG_SPE is undefined.
Restrict SPE exception handlers to e200/e500 cores adding CONFIG_SPE_POSSIBLE
and consequently guard __stup_ivors and __setup_cpu functions.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Guest visible debug register and hardware visible debug registers are
same, so ther is no need to have arch->shadow_dbg_reg, instead use
arch->dbg_reg.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Dbsr is not visible to userspace and we do not think any need to
expose this to userspace because:
Userspace cannot inject debug interrupt to guest (as this
does not know guest ability to handle debug interrupt), so
userspace will always clear DBSR.
Now if userspace has to always clear DBSR in KVM_EXIT_DEBUG
handling then clearing dbsr in kernel looks simple as this
avoid doing SET_SREGS/set_one_reg() to clear DBSR
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This patch changes the default behavior of MSRP_DEP, that is
guest is not allowed to change the MSR_DE, to guest can change
MSR_DE. When userspace is debugging guest then it override the
default behavior and set MSRP_DEP. This stops guest to change
MSR_DE when userspace is debugging guest.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This patch adds "rfdi" instruction emulation which is required for
guest debug hander on BOOKE-HV
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Debug interrupt can be either "critical level" or "debug level".
There are separate set of save/restore registers used for different level.
Example: DSRR0/DSRR1 are used for "debug level" and CSRR0/CSRR1
are used for critical level debug interrupt.
Using CPU_FTR_DEBUG_LVL_EXC to decide which interrupt level to be used.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Reported by Mikulas Patocka, kmemcheck currently barks out a
false positive since we don't have special kmemcheck annotation
for bitfields used in bpf_prog structure.
We currently have jited:1, len:31 and thus when accessing len
while CONFIG_KMEMCHECK enabled, kmemcheck throws a warning that
we're reading uninitialized memory.
As we don't need the whole bit universe for pages member, we
can just split it to u16 and use a bool flag for jited instead
of a bitfield.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch wires up three new syscalls for powerpc. The three
new syscalls are seccomp, getrandom and memfd_create.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
|
|
CONFIG_FHANDLE is a requirement for systemd and with the increasing
uptake of systemd within distros it makes sense for 64 bit defconfigs
to include it.
Signed-off-by: Cyril Bur <cyril.bur@au1.ibm.com>
|
|
As opal_message_init() uses machine_early_initcall(powernv, ), and
opal_hmi_handler_init() depends on that early initcall, so it also needs
use machine_* to check the machine_id.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
|
|
ABIv2 kernels are failing to backtrace through the kernel. An example:
39.30% readseek2_proce [kernel.kallsyms] [k] find_get_entry
|
--- find_get_entry
__GI___libc_read
The problem is in valid_next_sp() where we check that the new stack
pointer is at least STACK_FRAME_OVERHEAD below the previous one.
ABIv1 has a minimum stack frame size of 112 bytes consisting of 48 bytes
and 64 bytes of parameter save area. ABIv2 changes that to 32 bytes
with no paramter save area.
STACK_FRAME_OVERHEAD is in theory the minimum stack frame size,
but we over 240 uses of it, some of which assume that it includes
space for the parameter area.
We need to work through all our stack defines and rationalise them
but let's fix perf now by creating STACK_FRAME_MIN_SIZE and using
in valid_next_sp(). This fixes the issue:
30.64% readseek2_proce [kernel.kallsyms] [k] find_get_entry
|
--- find_get_entry
pagecache_get_page
generic_file_read_iter
new_sync_read
vfs_read
sys_read
syscall_exit
__GI___libc_read
Cc: stable@vger.kernel.org # 3.16+
Reported-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
|
|
Values acquired from Open Firmware are in 32-bit big endian format
and need to be handled on little endian architectures. This patch
ensures values are in cpu endian when hotplugging memory.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
|
|
|
|
Pull kvm fixes from Paolo Bonzini:
"A smattering of bug fixes across most architectures"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
powerpc/kvm/cma: Fix panic introduces by signed shift operation
KVM: s390/mm: Fix guest storage key corruption in ptep_set_access_flags
KVM: s390/mm: Fix storage key corruption during swapping
arm/arm64: KVM: Complete WFI/WFE instructions
ARM/ARM64: KVM: Nuke Hyp-mode tlbs before enabling MMU
KVM: s390/mm: try a cow on read only pages for key ops
KVM: s390: Fix user triggerable bug in dead code
|
|
With eBPF getting more extended and exposure to user space is on it's way,
hardening the memory range the interpreter uses to steer its command flow
seems appropriate. This patch moves the to be interpreted bytecode to
read-only pages.
In case we execute a corrupted BPF interpreter image for some reason e.g.
caused by an attacker which got past a verifier stage, it would not only
provide arbitrary read/write memory access but arbitrary function calls
as well. After setting up the BPF interpreter image, its contents do not
change until destruction time, thus we can setup the image on immutable
made pages in order to mitigate modifications to that code. The idea
is derived from commit 314beb9bcabf ("x86: bpf_jit_comp: secure bpf jit
against spraying attacks").
This is possible because bpf_prog is not part of sk_filter anymore.
After setup bpf_prog cannot be altered during its life-time. This prevents
any modifications to the entire bpf_prog structure (incl. function/JIT
image pointer).
Every eBPF program (including classic BPF that are migrated) have to call
bpf_prog_select_runtime() to select either interpreter or a JIT image
as a last setup step, and they all are being freed via bpf_prog_free(),
including non-JIT. Therefore, we can easily integrate this into the
eBPF life-time, plus since we directly allocate a bpf_prog, we have no
performance penalty.
Tested with seccomp and test_bpf testsuite in JIT/non-JIT mode and manual
inspection of kernel_page_tables. Brad Spengler proposed the same idea
via Twitter during development of this patch.
Joint work with Hannes Frederic Sowa.
Suggested-by: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fc95ca7284bc54953165cba76c3228bd2cdb9591 introduces a memset in
kvmppc_alloc_hpt since the general CMA doesn't clear the memory it
allocates.
However, the size argument passed to memset is computed from a signed value
and its signed bit is extended by the cast the compiler is doing. This lead
to extremely large size value when dealing with order value >= 31, and
almost all the memory following the allocated space is cleaned. As a
consequence, the system is panicing and may even fail spawning the kdump
kernel.
This fix makes use of an unsigned value for the memset's size argument to
avoid sign extension. Among this fix, another shift operation which may
lead to signed extended value too is also fixed.
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Alexander Graf <agraf@suse.de>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This patch fix spelling typo in printk.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
New system call depends on crypto. As it did not have a separate config
option, CONFIG_KEXEC was modified to select CRYPTO and CRYPTO_SHA256.
But now previous patch introduced a new config option for new syscall.
So CONFIG_KEXEC does not require crypto. Remove that dependency.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In the beggining was on_each_cpu(), which required an unused argument to
kvm_arch_ops.hardware_{en,dis}able, but this was soon forgotten.
Remove unnecessary arguments that stem from this.
Signed-off-by: Radim KrÄmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Using static inline is going to save few bytes and cycles.
For example on powerpc, the difference is 700 B after stripping.
(5 kB before)
This patch also deals with two overlooked empty functions:
kvm_arch_flush_shadow was not removed from arch/mips/kvm/mips.c
2df72e9bc KVM: split kvm_arch_flush_shadow
and kvm_arch_sched_in never made it into arch/ia64/kvm/kvm-ia64.c.
e790d9ef6 KVM: add kvm_arch_sched_in
Signed-off-by: Radim KrÄmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Opaque KVM structs are useful for prototypes in asm/kvm_host.h, to avoid
"'struct foo' declared inside parameter list" warnings (and consequent
breakage due to conflicting types).
Move them from individual files to a generic place in linux/kvm_types.h.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
Linus Torvalds
Aneesh Kumar K.V
Paolo Bonzini
David S. Miller
Michal Marek
Tang Chen
Andres Lagar-Cavilla
Alexander Graf
Madhavan Srinivasan
Mihai Caraman
Paul Mackerras
Paul Mackerras
Bharat Bhushan
Michael Neuling
Daniel Borkmann
Pranith Kumar
Cyril Bur
Li Zhong
Anton Blanchard
Thomas Falcon
Laurent Dufour
Masanari Iida
Vivek Goyal
Radim Krčmář
Geert Uytterhoeven