| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add code to save/restore registers during
R-standby sleep on SH-Mobile processors.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Add R-standby specific bits to the SuperH Mobile sleep code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Add MMU and cache handling functionality to the SuperH Mobile
sleep code. The MMU and cache registers are saved and restored.
The MMU is disabled and the cache is flushed and disabled before
entering sleep modes if the SUSP_SH_MMU flag is set. This flag
should be set in the case of R-standby and most likely for future
U-standby support as well.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Add code to keep track of supported sleep modes. This to
only export cpuidle modes that are backed by board support
code. Also, do not allow suspend-to-ram if sdram board code
is missing.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Rework the SuperH Mobile sleep code from including
board specific code to allowing each board to provide
pre/post code snippets. These snippets should contain
sdram management code to enter and leave self-refresh.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Add code to allow boards registering self-contained
functions for going to/from self-refresh. At this
point the board code is unused. When all supported
boards have been converted then the new sleep code
will make use of these functions.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch adds atomic notifier chains for pre/post
sleep events. Useful for cpu code and boards that
need to save and restore register state before and
after entering a sleep mode.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch adds cpuidle support for SuperH Mobile.
The sleep mode selected by cpuidle is compared with
the mode selected by the hwblk sleep code and the
best allowed mode is entered.
At this point "Sleep mode" and "Sleep mode + SF" are
supported. This code can easily be extended to support
"Software suspend mode", but the assembly code must
first be updated to avoid loosing interrupts.
Also, update the code to only copy the assembly snippet
into internal memory once at bootup.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch contains CONFIG_SUSPEND support to the SuperH
architecture. If enabled, SuperH Mobile processors will
register their suspend callbacks during boot.
To suspend, use "echo mem > /sys/power/state". To allow
wakeup, make sure "/sys/device/platform/../power/wakeup"
contains "enabled". Additional per-device driver patches
are most likely needed.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Add Suspend-to-disk / swsusp / CONFIG_HIBERNATION support
to the SuperH architecture.
To suspend, use "swapon /dev/sda2; echo disk > /sys/power/state"
To resume, pass "resume=/dev/sda2" on the kernel command line.
The patch "pm: rework includes, remove arch ifdefs V2" is
needed to allow the generic swsusp code to build properly.
Hibernation is not enabled with this patch though, a patch
setting ARCH_HIBERNATION_POSSIBLE will be submitted later.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
Magnus Damm
Magnus Damm