| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Turns out we over-engineered Direct Mode for stimers a bit: unlike
traditional stimers where we may want to try to re-inject the message upon
EOI, Direct Mode stimers just set the irq in APIC and kvm_apic_set_irq()
fails only when APIC is disabled (see APIC_DM_FIXED case in
__apic_accept_irq()). Remove the redundant part.
Suggested-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
stimers_pending optimization only helps us to avoid multiple
kvm_make_request() calls. This doesn't happen very often and these
calls are very cheap in the first place, remove open-coded version of
stimer_mark_pending() from kvm_hv_notify_acked_sint().
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Turns out Hyper-V on KVM (as of 2016) will only use synthetic timers
if direct mode is available. With direct mode we notify the guest by
asserting APIC irq instead of sending a SynIC message.
The implementation uses existing vec_bitmap for letting lapic code
know that we're interested in the particular IRQ's EOI request. We assume
that the same APIC irq won't be used by the guest for both direct mode
stimer and as sint source (especially with AutoEOI semantics). It is
unclear how things should be handled if that's not true.
Direct mode is also somewhat less expensive; in my testing
stimer_send_msg() takes not less than 1500 cpu cycles and
stimer_notify_direct() can usually be done in 300-400. WS2016 without
Hyper-V, however, always sticks to non-direct version.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
As a preparation to implementing Direct Mode for Hyper-V synthetic
timers switch to using stimer config definition from hyperv-tlfs.h.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
With every new Hyper-V Enlightenment we implement we're forced to add a
KVM_CAP_HYPERV_* capability. While this approach works it is fairly
inconvenient: the majority of the enlightenments we do have corresponding
CPUID feature bit(s) and userspace has to know this anyways to be able to
expose the feature to the guest.
Add KVM_GET_SUPPORTED_HV_CPUID ioctl (backed by KVM_CAP_HYPERV_CPUID, "one
cap to rule them all!") returning all Hyper-V CPUID feature leaves.
Using the existing KVM_GET_SUPPORTED_CPUID doesn't seem to be possible:
Hyper-V CPUID feature leaves intersect with KVM's (e.g. 0x40000000,
0x40000001) and we would probably confuse userspace in case we decide to
return these twice.
KVM_CAP_HYPERV_CPUID's number is interim: we're intended to drop
KVM_CAP_HYPERV_STIMER_DIRECT and use its number instead.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
hyperv-tlfs.h is a bit messy: CPUID feature bits are not always sorted,
it's hard to get which CPUID they belong to, some items are duplicated
(e.g. HV_X64_MSR_CRASH_CTL_NOTIFY/HV_CRASH_CTL_CRASH_NOTIFY).
Do some housekeeping work. While on it, replace all (1 << X) with BIT(X)
macro.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The SynIC message delivery protocol allows the message originator to
request, should the message slot be busy, to be notified when it's free.
However, this is unnecessary and even undesirable for messages generated
by SynIC timers in periodic mode: if the period is short enough compared
to the time the guest spends in the timer interrupt handler, so the
timer ticks start piling up, the excessive interactions due to this
notification and retried message delivery only makes the things worse.
[This was observed, in particular, with Windows L2 guests setting
(temporarily) the periodic timer to 2 kHz, and spending hundreds of
microseconds in the timer interrupt handler due to several L2->L1 exits;
under some load in L0 this could exceed 500 us so the timer ticks
started to pile up and the guest livelocked.]
Relieve the situation somewhat by not retrying message delivery for
periodic SynIC timers. This appears to remain within the "lazy" lost
ticks policy for SynIC timers as implemented in KVM.
Note that it doesn't solve the fundamental problem of livelocking the
guest with a periodic timer whose period is smaller than the time needed
to process a tick, but it makes it a bit less likely to be triggered.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
SynIC message delivery is somewhat overengineered: it pretends to follow
the ordering rules when grabbing the message slot, using atomic
operations and all that, but does it incorrectly and unnecessarily.
The correct order would be to first set .msg_pending, then atomically
replace .message_type if it was zero, and then clear .msg_pending if
the previous step was successful. But this all is done in vcpu context
so the whole update looks atomic to the guest (it's assumed to only
access the message page from this cpu), and therefore can be done in
whatever order is most convenient (and is also the reason why the
incorrect order didn't trigger any bugs so far).
While at this, also switch to kvm_vcpu_{read,write}_guest_page, and drop
the no longer needed synic_clear_sint_msg_pending.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
VP assist pages may hold valuable data which needs to be preserved across
migration. Clean PV EOI portion of the data on init, the guest is
responsible for making sure there's no garbage in the rest.
This will be used for nVMX migration, eVMCS address needs to be preserved.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The state related to the VP assist page is still managed by the LAPIC
code in the pv_eoi field.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Rewrite kvm_hv_flush_tlb()/send_ipi_vcpus_mask() making them cleaner and
somewhat more optimal.
hv_vcpu_in_sparse_set() is converted to sparse_set_to_vcpu_mask()
which copies sparse banks u64-at-a-time and then, depending on the
num_mismatched_vp_indexes value, returns immediately or does
vp index to vcpu index conversion by walking all vCPUs.
To support the change and make kvm_hv_send_ipi() look similar to
kvm_hv_flush_tlb() send_ipi_vcpus_mask() is introduced.
Suggested-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Regardless of whether your TLB is lush or not it still needs flushing.
Reported-by: Roman Kagan <rkagan@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Using hypercall for sending IPIs is faster because this allows to specify
any number of vCPUs (even > 64 with sparse CPU set), the whole procedure
will take only one VMEXIT.
Current Hyper-V TLFS (v5.0b) claims that HvCallSendSyntheticClusterIpi
hypercall can't be 'fast' (passing parameters through registers) but
apparently this is not true, Windows always uses it as 'fast' so we need
to support that.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
VP inedx almost always matches VCPU and when it does it's faster to walk
the sparse set instead of all vcpus.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This probably doesn't matter much (KVM_MAX_VCPUS is much lower nowadays)
but valid_bank_mask is really u64 and not unsigned long.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
In most common cases VP index of a vcpu matches its vcpu index. Userspace
is, however, free to set any mapping it wishes and we need to account for
that when we need to find a vCPU with a particular VP index. To keep search
algorithms optimal in both cases introduce 'num_mismatched_vp_indexes'
counter showing how many vCPUs with mismatching VP index we have. In case
the counter is zero we can assume vp_index == vcpu_idx.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Rename 'hv' to 'hv_vcpu' in kvm_hv_set_msr/kvm_hv_get_msr(); 'hv' is
'reserved' for 'struct kvm_hv' variables across the file.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
We can use 'NULL' to represent 'all cpus' case in
kvm_make_vcpus_request_mask() and avoid building vCPU mask with
all vCPUs.
Suggested-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Hyper-V TLFS (5.0b) states:
> Virtual processors are identified by using an index (VP index). The
> maximum number of virtual processors per partition supported by the
> current implementation of the hypervisor can be obtained through CPUID
> leaf 0x40000005. A virtual processor index must be less than the
> maximum number of virtual processors per partition.
Forbid userspace to set VP_INDEX above KVM_MAX_VCPUS. get_vcpu_by_vpidx()
can now be optimized to bail early when supplied vpidx is >= KVM_MAX_VCPUS.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Some of the MSRs returned by GET_MSR_INDEX_LIST currently cannot be sent back
to KVM_GET_MSR and/or KVM_SET_MSR; either they can never be sent back, or you
they are only accepted under special conditions. This makes the API a pain to
use.
To avoid this pain, this patch makes it so that the result of the get-list
ioctl can always be used for host-initiated get and set. Since we don't have
a separate way to check for read-only MSRs, this means some Hyper-V MSRs are
ignored when written. Arguably they should not even be in the result of
GET_MSR_INDEX_LIST, but I am leaving there in case userspace is using the
outcome of GET_MSR_INDEX_LIST to derive the support for the corresponding
Hyper-V feature.
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Pull KVM updates from Paolo Bonzini:
"Small update for KVM:
ARM:
- lazy context-switching of FPSIMD registers on arm64
- "split" regions for vGIC redistributor
s390:
- cleanups for nested
- clock handling
- crypto
- storage keys
- control register bits
x86:
- many bugfixes
- implement more Hyper-V super powers
- implement lapic_timer_advance_ns even when the LAPIC timer is
emulated using the processor's VMX preemption timer.
- two security-related bugfixes at the top of the branch"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (79 commits)
kvm: fix typo in flag name
kvm: x86: use correct privilege level for sgdt/sidt/fxsave/fxrstor access
KVM: x86: pass kvm_vcpu to kvm_read_guest_virt and kvm_write_guest_virt_system
KVM: x86: introduce linear_{read,write}_system
kvm: nVMX: Enforce cpl=0 for VMX instructions
kvm: nVMX: Add support for "VMWRITE to any supported field"
kvm: nVMX: Restrict VMX capability MSR changes
KVM: VMX: Optimize tscdeadline timer latency
KVM: docs: nVMX: Remove known limitations as they do not exist now
KVM: docs: mmu: KVM support exposing SLAT to guests
kvm: no need to check return value of debugfs_create functions
kvm: Make VM ioctl do valloc for some archs
kvm: Change return type to vm_fault_t
KVM: docs: mmu: Fix link to NPT presentation from KVM Forum 2008
kvm: x86: Amend the KVM_GET_SUPPORTED_CPUID API documentation
KVM: x86: hyperv: declare KVM_CAP_HYPERV_TLBFLUSH capability
KVM: x86: hyperv: simplistic HVCALL_FLUSH_VIRTUAL_ADDRESS_{LIST,SPACE}_EX implementation
KVM: x86: hyperv: simplistic HVCALL_FLUSH_VIRTUAL_ADDRESS_{LIST,SPACE} implementation
KVM: introduce kvm_make_vcpus_request_mask() API
KVM: x86: hyperv: do rep check for each hypercall separately
...
|
|
Implement HvFlushVirtualAddress{List,Space}Ex hypercalls in the same way
we've implemented non-EX counterparts.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
[Initialized valid_bank_mask to silence misguided GCC warnigs. - Radim]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
Implement HvFlushVirtualAddress{List,Space} hypercalls in a simplistic way:
do full TLB flush with KVM_REQ_TLB_FLUSH and kick vCPUs which are currently
IN_GUEST_MODE.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
Prepare to support TLB flush hypercalls, some of which are REP hypercalls.
Also, return HV_STATUS_INVALID_HYPERCALL_INPUT as it seems more
appropriate.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
Avoid open-coding offsets for hypercall input parameters, we already
have defines for them.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
If the hypercall was called from userspace or real mode, KVM injects #UD
and then advances RIP, so it looks like #UD was caused by the following
instruction. This probably won't cause more than confusion, but could
give an unexpected access to guest OS' instruction emulator.
Also, refactor the code to count hv hypercalls that were handled by the
virt userspace.
Fixes: 6356ee0c9602 ("x86: Delay skip of emulated hypercall instruction")
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
Even though the eventfd is released after the KVM SRCU grace period
elapses, the conn_to_evt data structure itself is not; it uses RCU
internally, instead. Fix the read-side critical section to happen
under rcu_read_lock/unlock; the result is still protected by
vcpu->kvm->srcu.
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The IP increment should be done after the hypercall emulation, after
calling the various handlers. In this way, these handlers can accurately
identify the the IP of the VMCALL if they need it.
This patch keeps the same functionality for the Hyper-V handler which does
not use the return code of the standard kvm_skip_emulated_instruction()
call.
Signed-off-by: Marian Rotariu <mrotariu@bitdefender.com>
[Hyper-V hypercalls also need kvm_skip_emulated_instruction() - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The assist page has been used only for the paravirtual EOI so far, hence
the "APIC" in the MSR name. Renaming to match the Hyper-V TLFS where it's
called "Virtual VP Assist MSR".
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
"rep_done" is always zero so the "(((u64)rep_done & 0xfff) << 32)"
expression is just zero. We can remove the "res" temporary variable as
well and just use "ret" directly.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Hyper-V 2016 on KVM with SynIC enabled doesn't boot with the following
trace:
kvm_entry: vcpu 0
kvm_exit: reason MSR_WRITE rip 0xfffff8000131c1e5 info 0 0
kvm_hv_synic_set_msr: vcpu_id 0 msr 0x40000090 data 0x10000 host 0
kvm_msr: msr_write 40000090 = 0x10000 (#GP)
kvm_inj_exception: #GP (0x0)
KVM acts according to the following statement from TLFS:
"
11.8.4 SINTx Registers
...
Valid values for vector are 16-255 inclusive. Specifying an invalid
vector number results in #GP.
"
However, I checked and genuine Hyper-V doesn't #GP when we write 0x10000
to SINTx. I checked with Microsoft and they confirmed that if either the
Masked bit (bit 16) or the Polling bit (bit 18) is set to 1, then they
ignore the value of Vector. Make KVM act accordingly.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
When a new vector is written to SINx we update vec_bitmap/auto_eoi_bitmap
but we forget to remove old vector from these masks (in case it is not
present in some other SINTx).
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
Nested Hyper-V/Windows guest running on top of KVM will use TSC page
clocksource in two cases:
- L0 exposes invariant TSC (CPUID.80000007H:EDX[8]).
- L0 provides Hyper-V Reenlightenment support (CPUID.40000003H:EAX[13]).
Exposing invariant TSC effectively blocks migration to hosts with different
TSC frequencies, providing reenlightenment support will be needed when we
start migrating nested workloads.
Implement rudimentary support for reenlightenment MSRs. For now, these are
just read/write MSRs with no effect.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
In Hyper-V, the fast guest->host notification mechanism is the
SIGNAL_EVENT hypercall, with a single parameter of the connection ID to
signal.
Currently this hypercall incurs a user exit and requires the userspace
to decode the parameters and trigger the notification of the potentially
different I/O context.
To avoid the costly user exit, process this hypercall and signal the
corresponding eventfd in KVM, similar to ioeventfd. The association
between the connection id and the eventfd is established via the newly
introduced KVM_HYPERV_EVENTFD ioctl, and maintained in an
(srcu-protected) IDR.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
[asm/hyperv.h changes approved by KY Srinivasan. - Radim]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
Move kvm.arch.hyperv initialization and cleanup to separate functions.
For now only a mutex is inited in the former, and the latter is empty;
more stuff will go in there in a followup patch.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
get_cpl requires vcpu_load, so we must cache the result (whether the
vcpu was preempted when its cpl=0) in kvm_vcpu_arch.
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
If a vcpu exits due to request a user mode spinlock, then
the spinlock-holder may be preempted in user mode or kernel mode.
(Note that not all architectures trap spin loops in user mode,
only AMD x86 and ARM/ARM64 currently do).
But if a vcpu exits in kernel mode, then the holder must be
preempted in kernel mode, so we should choose a vcpu in kernel mode
as a more likely candidate for the lock holder.
This introduces kvm_arch_vcpu_in_kernel() to decide whether the
vcpu is in kernel-mode when it's preempted. kvm_vcpu_on_spin's
new argument says the same of the spinning VCPU.
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
It has been experimentally confirmed that supporting these two MSRs is one
of the necessary conditions for nested Hyper-V to use the TSC page. Modern
Windows guests are noticeably slower when they fall back to reading
timestamps from the HV_X64_MSR_TIME_REF_COUNT MSR instead of using the TSC
page.
The newly supported MSRs are advertised with the AccessFrequencyRegs
partition privilege flag and CPUID.40000003H:EDX[8] "Support for
determining timer frequencies is available" (both outside of the scope of
this KVM patch).
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
If the SynIC timer message delivery fails due to SINT message slot being
busy, there's no point to attempt starting the timer again until we're
notified of the slot being released by the guest (via EOM or EOI).
Even worse, when a oneshot timer fails to deliver its message, its
re-arming with an expiration time in the past leads to immediate retry
of the delivery, and so on, without ever letting the guest vcpu to run
and release the slot, which results in a livelock.
To avoid that, only start the timer when there's no timer message
pending delivery. When there is, meaning the slot is busy, the
processing will be restarted upon notification from the guest that the
slot is released.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
Hyper-V identifies vCPUs by Virtual Processor Index, which can be
queried via HV_X64_MSR_VP_INDEX msr. It is defined by the spec as a
sequential number which can't exceed the maximum number of vCPUs per VM.
APIC ids can be sparse and thus aren't a valid replacement for VP
indices.
Current KVM uses its internal vcpu index as VP_INDEX. However, to make
it predictable and persistent across VM migrations, the userspace has to
control the value of VP_INDEX.
This patch achieves that, by storing vp_index explicitly on vcpu, and
allowing HV_X64_MSR_VP_INDEX to be set from the host side. For
compatibility it's initialized to KVM vcpu index. Also a few variables
are renamed to make clear distinction betweed this Hyper-V vp_index and
KVM vcpu_id (== APIC id). Besides, a new capability,
KVM_CAP_HYPERV_VP_INDEX, is added to allow the userspace to skip
attempting msr writes where unsupported, to avoid spamming error logs.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
There is a flaw in the Hyper-V SynIC implementation in KVM: when message
page or event flags page is enabled by setting the corresponding msr,
KVM zeroes it out. This is problematic because on migration the
corresponding MSRs are loaded on the destination, so the content of
those pages is lost.
This went unnoticed so far because the only user of those pages was
in-KVM hyperv synic timers, which could continue working despite that
zeroing.
Newer QEMU uses those pages for Hyper-V VMBus implementation, and
zeroing them breaks the migration.
Besides, in newer QEMU the content of those pages is fully managed by
QEMU, so zeroing them is undesirable even when writing the MSRs from the
guest side.
To support this new scheme, introduce a new capability,
KVM_CAP_HYPERV_SYNIC2, which, when enabled, makes sure that the synic
pages aren't zeroed out in KVM.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
Introduce a trivial, mostly empty <linux/sched/cputime.h> header
to prepare for the moving of cputime functionality out of sched.h.
Update all code that relies on these facilities.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Pull KVM updates from Paolo Bonzini:
"4.11 is going to be a relatively large release for KVM, with a little
over 200 commits and noteworthy changes for most architectures.
ARM:
- GICv3 save/restore
- cache flushing fixes
- working MSI injection for GICv3 ITS
- physical timer emulation
MIPS:
- various improvements under the hood
- support for SMP guests
- a large rewrite of MMU emulation. KVM MIPS can now use MMU
notifiers to support copy-on-write, KSM, idle page tracking,
swapping, ballooning and everything else. KVM_CAP_READONLY_MEM is
also supported, so that writes to some memory regions can be
treated as MMIO. The new MMU also paves the way for hardware
virtualization support.
PPC:
- support for POWER9 using the radix-tree MMU for host and guest
- resizable hashed page table
- bugfixes.
s390:
- expose more features to the guest
- more SIMD extensions
- instruction execution protection
- ESOP2
x86:
- improved hashing in the MMU
- faster PageLRU tracking for Intel CPUs without EPT A/D bits
- some refactoring of nested VMX entry/exit code, preparing for live
migration support of nested hypervisors
- expose yet another AVX512 CPUID bit
- host-to-guest PTP support
- refactoring of interrupt injection, with some optimizations thrown
in and some duct tape removed.
- remove lazy FPU handling
- optimizations of user-mode exits
- optimizations of vcpu_is_preempted() for KVM guests
generic:
- alternative signaling mechanism that doesn't pound on
tsk->sighand->siglock"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (195 commits)
x86/kvm: Provide optimized version of vcpu_is_preempted() for x86-64
x86/paravirt: Change vcp_is_preempted() arg type to long
KVM: VMX: use correct vmcs_read/write for guest segment selector/base
x86/kvm/vmx: Defer TR reload after VM exit
x86/asm/64: Drop __cacheline_aligned from struct x86_hw_tss
x86/kvm/vmx: Simplify segment_base()
x86/kvm/vmx: Get rid of segment_base() on 64-bit kernels
x86/kvm/vmx: Don't fetch the TSS base from the GDT
x86/asm: Define the kernel TSS limit in a macro
kvm: fix page struct leak in handle_vmon
KVM: PPC: Book3S HV: Disable HPT resizing on POWER9 for now
KVM: Return an error code only as a constant in kvm_get_dirty_log()
KVM: Return an error code only as a constant in kvm_get_dirty_log_protect()
KVM: Return directly after a failed copy_from_user() in kvm_vm_compat_ioctl()
KVM: x86: remove code for lazy FPU handling
KVM: race-free exit from KVM_RUN without POSIX signals
KVM: PPC: Book3S HV: Turn "KVM guest htab" message into a debug message
KVM: PPC: Book3S PR: Ratelimit copy data failure error messages
KVM: Support vCPU-based gfn->hva cache
KVM: use separate generations for each address space
...
|
|
Now that most cputime readers use the transition API which return the
task cputime in old style cputime_t, we can safely store the cputime in
nsecs. This will eventually make cputime statistics less opaque and more
granular. Back and forth convertions between cputime_t and nsecs in order
to deal with cputime_t random granularity won't be needed anymore.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1485832191-26889-8-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Interrupt to self can be sent without knowing the APIC ID.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Introduce a new mutex to avoid an AB-BA deadlock between kvm->lock and
vcpu->mutex. Protect accesses in kvm_hv_setup_tsc_page too, as suggested
by Roman.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
synic_set_irq is only used in hyperv.c, and should be static to
avoid compiling warning when with -Wmissing-prototypes option.
Signed-off-by: Jiang Biao <jiang.biao2@zte.com.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Lately tsc page was implemented but filled with empty
values. This patch setup tsc page scale and offset based
on vcpu tsc, tsc_khz and HV_X64_MSR_TIME_REF_COUNT value.
The valid tsc page drops HV_X64_MSR_TIME_REF_COUNT msr
reads count to zero which potentially improves performance.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Peter Hornyack <peterhornyack@google.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
[Computation of TSC page parameters rewritten to use the Linux timekeeper
parameters. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Introduce a function that reads the exact nanoseconds value that is
provided to the guest in kvmclock. This crystallizes the notion of
kvmclock as a thin veneer over a stable TSC, that the guest will
(hopefully) convert with NTP. In other words, kvmclock is *not* a
paravirtualized host-to-guest NTP.
Drop the get_kernel_ns() function, that was used both to get the base
value of the master clock and to get the current value of kvmclock.
The former use is replaced by ktime_get_boot_ns(), the latter is
the purpose of get_kernel_ns().
This also allows KVM to provide a Hyper-V time reference counter that
is synchronized with the time that is computed from the TSC page.
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
If SynIC is disabled, there is nothing that userspace can do to
handle these exits; on the other hand, userspace probably will
not know about KVM_EXIT_HYPERV_HCALL and complain about it or
even exit. Just prevent anything bad from happening by handling
the hypercall in KVM and returning an "invalid hypercall" code.
Fixes: 83326e43f27e9a8a501427a0060f8af519a39bb2
Cc: Andrey Smetanin <irqlevel@gmail.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
Vitaly Kuznetsov
Roman Kagan
Ladi Prosek
Paolo Bonzini
Linus Torvalds
Radim Krčmář
Marian Rotariu
Dan Carpenter
Longpeng(Mike)
Ingo Molnar
Frederic Weisbecker
Jiang Biao