Age | Commit message (Collapse) | Author | Files | Lines |
|
Check that KVM_CAP_HYPERV_ENLIGHTENED_VMCS returns correct version range.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Commit e2e871ab2f02 ("x86/kvm/hyper-v: Introduce nested_get_evmcs_version()
helper") broke EVMCS enablement: to set vmcs_version we now call
nested_get_evmcs_version() but this function checks
enlightened_vmcs_enabled flag which is not yet set so we end up returning
zero.
Fix the issue by re-arranging things in nested_enable_evmcs().
Fixes: e2e871ab2f02 ("x86/kvm/hyper-v: Introduce nested_get_evmcs_version() helper")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
...along with the function's STACK_FRAME_NON_STANDARD tag. Moving the
asm blob results in a significantly smaller amount of code that is
marked with STACK_FRAME_NON_STANDARD, which makes it far less likely
that gcc will split the function and trigger a spurious objtool warning.
As a bonus, removing STACK_FRAME_NON_STANDARD from vmx_vcpu_run() allows
the bulk of code to be properly checked by objtool.
Because %rbp is not loaded via VMCS fields, vmx_vcpu_run() must manually
save/restore the host's RBP and load the guest's RBP prior to calling
vmx_vmenter(). Modifying %rbp triggers objtool's stack validation code,
and so vmx_vcpu_run() is tagged with STACK_FRAME_NON_STANDARD since it's
impossible to avoid modifying %rbp.
Unfortunately, vmx_vcpu_run() is also a gigantic function that gcc will
split into separate functions, e.g. so that pieces of the function can
be inlined. Splitting the function means that the compiled Elf file
will contain one or more vmx_vcpu_run.part.* functions in addition to
a vmx_vcpu_run function. Depending on where the function is split,
objtool may warn about a "call without frame pointer save/setup" in
vmx_vcpu_run.part.* since objtool's stack validation looks for exact
names when whitelisting functions tagged with STACK_FRAME_NON_STANDARD.
Up until recently, the undesirable function splitting was effectively
blocked because vmx_vcpu_run() was tagged with __noclone. At the time,
__noclone had an unintended side effect that put vmx_vcpu_run() into a
separate optimization unit, which in turn prevented gcc from inlining
the function (or any of its own function calls) and thus eliminated gcc's
motivation to split the function. Removing the __noclone attribute
allowed gcc to optimize vmx_vcpu_run(), exposing the objtool warning.
Kudos to Qian Cai for root causing that the fnsplit optimization is what
caused objtool to complain.
Fixes: 453eafbe65f7 ("KVM: VMX: Move VM-Enter + VM-Exit handling to non-inline sub-routines")
Tested-by: Qian Cai <cai@lca.pw>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Fix a call to userspace_mem_region_find to conform to its spec of
taking an inclusive, inclusive range. It was previously being called
with an inclusive, exclusive range. Also remove a redundant region bounds
check in vm_userspace_mem_region_add. Region overlap checking is already
performed by the call to userspace_mem_region_find.
Tested: Compiled tools/testing/selftests/kvm with -static
Ran all resulting test binaries on an Intel Haswell test machine
All tests passed
Signed-off-by: Ben Gardon <bgardon@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
We get some warnings when building kernel with W=1:
arch/x86/kvm/vmx/vmx.c:426:5: warning: no previous prototype for ‘kvm_fill_hv_flush_list_func’ [-Wmissing-prototypes]
arch/x86/kvm/vmx/nested.c:58:6: warning: no previous prototype for ‘init_vmcs_shadow_fields’ [-Wmissing-prototypes]
Make them static to fix this.
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
kvm-unit-tests' eventinj "NMI failing on IDT" test results in NMI being
delivered to the host (L1) when it's running nested. The problem seems to
be: svm_complete_interrupts() raises 'nmi_injected' flag but later we
decide to reflect EXIT_NPF to L1. The flag remains pending and we do NMI
injection upon entry so it got delivered to L1 instead of L2.
It seems that VMX code solves the same issue in prepare_vmcs12(), this was
introduced with code refactoring in commit 5f3d5799974b ("KVM: nVMX: Rework
event injection and recovery").
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
In case of incomplete IPI with invalid interrupt type, the current
SVM driver does not properly emulate the IPI, and fails to boot
FreeBSD guests with multiple vcpus when enabling AVIC.
Fix this by update APIC ICR high/low registers, which also
emulate sending the IPI.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Print warning message when IPI target ID is invalid due to one of
the following reasons:
* In logical mode: cluster > max_cluster (64)
* In physical mode: target > max_physical (512)
* Address is not present in the physical or logical ID tables
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
KVM hypercalls return a negative value error code in case of a fatal
error, e.g. when the hypercall isn't supported or was made with invalid
parameters. WARN_ONCE on fatal errors when sending PV IPIs as any such
error all but guarantees an SMP system will hang due to a missing IPI.
Fixes: aaffcfd1e82d ("KVM: X86: Implement PV IPIs in linux guest")
Cc: stable@vger.kernel.org
Cc: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The recognition of the KVM_HC_SEND_IPI hypercall was unintentionally
wrapped in "#ifdef CONFIG_X86_64", causing 32-bit KVM hosts to reject
any and all PV IPI requests despite advertising the feature. This
results in all KVM paravirtualized guests hanging during SMP boot due
to IPIs never being delivered.
Fixes: 4180bf1b655a ("KVM: X86: Implement "send IPI" hypercall")
Cc: stable@vger.kernel.org
Cc: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
We shouldn't probably be suggesting using Enlightened VMCS when it's not
enabled (not supported from guest's point of view). Hyper-V on KVM seems
to be fine either way but let's be consistent.
Fixes: 2bc39970e932 ("x86/kvm/hyper-v: Introduce KVM_GET_SUPPORTED_HV_CPUID")
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
System reset through synthetic MSR is not recommended neither by genuine
Hyper-V nor my QEMU.
Fixes: 2bc39970e932 ("x86/kvm/hyper-v: Introduce KVM_GET_SUPPORTED_HV_CPUID")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This changes the allocation of cached_vmcs12 to use kzalloc instead of
kmalloc. This removes the information leak found by Syzkaller (see
Reported-by) in this case and prevents similar leaks from happening
based on cached_vmcs12.
It also changes vmx_get_nested_state to copy out the full 4k VMCS12_SIZE
in copy_to_user rather than only the size of the struct.
Tested: rebuilt against head, booted, and ran the syszkaller repro
https://syzkaller.appspot.com/text?tag=ReproC&x=174efca3400000 without
observing any problems.
Reported-by: syzbot+ded1696f6b50b615b630@syzkaller.appspotmail.com
Fixes: 8fcc4b5923af5de58b80b53a069453b135693304
Cc: stable@vger.kernel.org
Signed-off-by: Tom Roeder <tmroeder@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Fix a recently introduced bug that results in the wrong VMCS control
field being updated when applying a IA32_PERF_GLOBAL_CTRL errata.
Fixes: c73da3fcab43 ("KVM: VMX: Properly handle dynamic VM Entry/Exit controls")
Reported-by: Harald Arnesen <harald@skogtun.org>
Tested-by: Harald Arnesen <harald@skogtun.org>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The single-step debugging of KVM guests on x86 is broken: if we run
gdb 'stepi' command at the breakpoint when the guest interrupts are
enabled, RIP always jumps to native_apic_mem_write(). Then other
nasty effects follow.
Long investigation showed that on Jun 7, 2017 the
commit c8401dda2f0a00cd25c0 ("KVM: x86: fix singlestepping over syscall")
introduced the kvm_run.debug corruption: kvm_vcpu_do_singlestep() can
be called without X86_EFLAGS_TF set.
Let's fix it. Please consider that for -stable.
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Cc: stable@vger.kernel.org
Fixes: c8401dda2f0a00cd25c0 ("KVM: x86: fix singlestepping over syscall")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
HV_X64_MSR_GUEST_IDLE_AVAILABLE appeared in kvm_vcpu_ioctl_get_hv_cpuid()
by mistake: it announces support for HV_X64_MSR_GUEST_IDLE (0x400000F0)
which we don't support in KVM (yet).
Fixes: 2bc39970e932 ("x86/kvm/hyper-v: Introduce KVM_GET_SUPPORTED_HV_CPUID")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Recently, DMG frequency bands have been extended till 71GHz, so extend
the range check till 20GHz (45-71GHZ), else some channels will be marked
as disabled.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@bluwireless.co.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If there are simulatenous queries of regdb, then there might be a case
where multiple queries can trigger request_firmware_no_wait and can have
parallel callbacks being executed asynchronously. In this scenario we
might hit the WARN_ON.
So remove the warn_on, as the code already handles multiple callbacks
gracefully.
Signed-off-by: Chaitanya Tata <chaitanya.tata@bluwireless.co.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
During refactor in commit 9e478066eae4 ("mac80211: fix MU-MIMO
follow-MAC mode") a new struct 'action' was declared with packed
attribute as:
struct {
struct ieee80211_hdr_3addr hdr;
u8 category;
u8 action_code;
} __packed action;
But since struct 'ieee80211_hdr_3addr' is declared with an aligned
keyword as:
struct ieee80211_hdr {
__le16 frame_control;
__le16 duration_id;
u8 addr1[ETH_ALEN];
u8 addr2[ETH_ALEN];
u8 addr3[ETH_ALEN];
__le16 seq_ctrl;
u8 addr4[ETH_ALEN];
} __packed __aligned(2);
Solve the ambiguity of placing aligned structure in a packed one by
adding the aligned(2) attribute to struct 'action'.
This removes the following warning (W=1):
net/mac80211/rx.c:234:2: warning: alignment 1 of 'struct <anonymous>' is less than 2 [-Wpacked-not-aligned]
Cc: Johannes Berg <johannes.berg@intel.com>
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Following call trace is observed while adding TDLS peer entry in driver
during TDLS setup.
Call Trace:
[<c1301476>] dump_stack+0x47/0x61
[<c10537d2>] __warn+0xe2/0x100
[<fa22415f>] ? sta_apply_parameters+0x49f/0x550 [mac80211]
[<c1053895>] warn_slowpath_null+0x25/0x30
[<fa22415f>] sta_apply_parameters+0x49f/0x550 [mac80211]
[<fa20ad42>] ? sta_info_alloc+0x1c2/0x450 [mac80211]
[<fa224623>] ieee80211_add_station+0xe3/0x160 [mac80211]
[<c1876fe3>] nl80211_new_station+0x273/0x420
[<c170f6d9>] genl_rcv_msg+0x219/0x3c0
[<c170f4c0>] ? genl_rcv+0x30/0x30
[<c170ee7e>] netlink_rcv_skb+0x8e/0xb0
[<c170f4ac>] genl_rcv+0x1c/0x30
[<c170e8aa>] netlink_unicast+0x13a/0x1d0
[<c170ec18>] netlink_sendmsg+0x2d8/0x390
[<c16c5acd>] sock_sendmsg+0x2d/0x40
[<c16c6369>] ___sys_sendmsg+0x1d9/0x1e0
Fixing this by allowing TDLS setup request only when we have completed
association.
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
syzbot reported an out-of-bounds read when passing certain
malformed messages into nl80211. The specific place where
this happened isn't interesting, the problem is that nested
policy parsing was referring to the wrong maximum attribute
and thus the policy wasn't long enough.
Fix this by referring to the correct attribute. Since this
is really not necessary, I'll come up with a separate patch
to just pass the policy instead of both, in the common case
we can infer the maxattr from the size of the policy array.
Reported-by: syzbot+4157b036c5f4713b1f2f@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Fixes: 9bb7e0f24e7e ("cfg80211: add peer measurement with FTM initiator API")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Remove duplicated include.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IBM virtual ethernet driver's polling function continues
to process frames after rescheduling NAPI, resulting in a warning
if it exhausted its budget. Do not restart polling after calling
napi_reschedule. Instead let frames be processed in the following
instance.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__bpf_redirect() and act_mirred checks this boolean
to determine whether to prefix an ethernet header.
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ax88772_bind() should return error code immediately when the PHY
was not reset properly through ax88772a_hw_reset().
Otherwise, The asix_get_phyid() will block when get the PHY
Identifier from the PHYSID1 MII registers through asix_mdio_read()
due to the PHY isn't ready. Furthermore, it will produce a lot of
error message cause system crash.As follows:
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to send
software reset: ffffffb9
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to enable
software MII access
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to read
reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to enable
software MII access
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to read
reg index 0x0000: -71
...
Signed-off-by: Zhang Run <zhang.run@zte.com.cn>
Reviewed-by: Yang Wei <yang.wei9@zte.com.cn>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
max_rcvbuf_size is no longer used since commit "414574a0af36".
Signed-off-by: Zhaolong Zhang <zhangzl2013@126.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Following Marvell's acquisition of Cavium, we need to update all the
Cavium drivers maintainer's entries to point to our new e-mail addresses.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ameen Rahman <Ameen.Rahman@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Aggregation effects are extremely common with wifi, cellular, and cable
modem link technologies, ACK decimation in middleboxes, and LRO and GRO
in receiving hosts. The aggregation can happen in either direction,
data or ACKs, but in either case the aggregation effect is visible
to the sender in the ACK stream.
Previously BBR's sending was often limited by cwnd under severe ACK
aggregation/decimation because BBR sized the cwnd at 2*BDP. If packets
were acked in bursts after long delays (e.g. one ACK acking 5*BDP after
5*RTT), BBR's sending was halted after sending 2*BDP over 2*RTT, leaving
the bottleneck idle for potentially long periods. Note that loss-based
congestion control does not have this issue because when facing
aggregation it continues increasing cwnd after bursts of ACKs, growing
cwnd until the buffer is full.
To achieve good throughput in the presence of aggregation effects, this
algorithm allows the BBR sender to put extra data in flight to keep the
bottleneck utilized during silences in the ACK stream that it has evidence
to suggest were caused by aggregation.
A summary of the algorithm: when a burst of packets are acked by a
stretched ACK or a burst of ACKs or both, BBR first estimates the expected
amount of data that should have been acked, based on its estimated
bandwidth. Then the surplus ("extra_acked") is recorded in a windowed-max
filter to estimate the recent level of observed ACK aggregation. Then cwnd
is increased by the ACK aggregation estimate. The larger cwnd avoids BBR
being cwnd-limited in the face of ACK silences that recent history suggests
were caused by aggregation. As a sanity check, the ACK aggregation degree
is upper-bounded by the cwnd (at the time of measurement) and a global max
of BW * 100ms. The algorithm is further described by the following
presentation:
https://datatracker.ietf.org/meeting/101/materials/slides-101-iccrg-an-update-on-bbr-work-at-google-00
In our internal testing, we observed a significant increase in BBR
throughput (measured using netperf), in a basic wifi setup.
- Host1 (sender on ethernet) -> AP -> Host2 (receiver on wifi)
- 2.4 GHz -> BBR before: ~73 Mbps; BBR after: ~102 Mbps; CUBIC: ~100 Mbps
- 5.0 GHz -> BBR before: ~362 Mbps; BBR after: ~593 Mbps; CUBIC: ~601 Mbps
Also, this code is running globally on YouTube TCP connections and produced
significant bandwidth increases for YouTube traffic.
This is based on Ian Swett's max_ack_height_ algorithm from the
QUIC BBR implementation.
Signed-off-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Because bbr_target_cwnd() is really a general-purpose BBR helper for
computing some volume of inflight data as a function of the estimated
BDP, refactor it into following helper functions:
- bbr_bdp()
- bbr_quantization_budget()
- bbr_inflight()
Signed-off-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Few chip versions use the same sequence to adjust 10M and ALDPS, so
let's factor it out. This patch also fixes a (most likely) typo in
rtl8168g_1_hw_phy_config. There bit 8 in reg 0x14 on page 0x0bcc
was set and not cleared. According to the vendor driver this bit
needs to be cleared in all cases.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Chip versions from RTL8168g onward use the same sequence to disable
ALDPS (Advanced Link-Down Power Saving). So let's factor this out.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I made a dumb mistake when I summed up the slave stats, obviously slaves
can come and go which would make the master stats unreliable.
Count and export the master stats separately.
Fixes: a258aeacd7f0 ("bonding: add support for xstats and export 3ad stats")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we enable the interrupts in phy_start() we don't have to do it
before. Therefore remove enabling interrupts from phy_start_interrupts()
and rename this function to reflect the changed functionality.
v2:
- improve warning to clearly state that we fall back to polling
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Interrupts don't have to be enabled before calling phy_start().
Therefore let's enable them in phy_start(). In a subsequent step
we'll remove enabling interrupts from phy_connect_direct().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy_start() should be called from states PHY_READY or PHY_HALTED only.
Check for this to detect misbehaving drivers. Also the state machine
should be started only when being called from one of the valid states.
Some more background:
For all invalid states phy_start() basically was a no-op. All it did
was triggering a state machine run, but for all "running" states the
poll loop was active anyway. And if called from PHY_DOWN, the state
machine does nothing.
v3:
- extended commit message
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The state machine is a no-op before phy_start() has been called.
Therefore let's enable it in phy_start() only. In phy_start()
let's call phy_start_machine() instead of phy_trigger_machine().
phy_start_machine is an alias for phy_trigger_machine but it makes
clearer that we start the state machine here instead of just
triggering a run.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of error, the function devm_clk_get() returns ERR_PTR() and
never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR().
Fixes: a7c30e62d4b8 ("net: stmmac: Add driver for Qualcomm ethqos")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Two statements are incorrecly indented, fix these by removing a space.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A ternary match table is used for RFS. If multiple entries in the table
match, the entry with the lowest numerical values index is chosen as the
matching entry. Entries in the table are identified using an index
which takes a value from 0 to PRFSCAPR[NUM_RFS]-1 when accessed by the
PSI (PF).
Portions of the RFS table can be assigned to each SI by the PSI (PF)
driver in PSIaRFSCFGR. Assignments are cumulative, the entries assigned
to SIn start after those assigned to SIn-1. The total assignments to
all SIs must be equal to or less than the number available to the port
as found in PRFSCAPR.
For RSS, the Toeplitz hash function used requires two inputs, a 40B
random secret key that is supplied through the PRSSKR0-9 registers as well
as the relevant pieces of the packet header (n-tuple). The 6 LSB bits of
the hash function result will then be used as a pointer to obtain the tag
referenced in the 64 entry indirection table. The result will provide a
winning group which will be used to help route the received packet.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VSIs (VFs) may send a message to the PSI (PF) for general notification
or to gain access to hardware resources which requires host inspection.
These messages may vary in size and are handled as a partition copy
between two memory regions owned by the respective participants.
The PSI will respond with fail or success and a 16-bit message code.
The patch implements the vf to pf messaging mechanism above and, as the
first application making use of this support, it enables the VF to
configure its own primary MAC address.
Signed-off-by: Catalin Horghidan <catalin.horghidan@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds most h/w statistics counters: non-privileged SI conters, as
well as privileged Port and MAC counters available only to the PF.
Per ring software stats are also included.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ENETC is a multi-port virtualized Ethernet controller supporting GbE
designs and Time-Sensitive Networking (TSN) functionality.
ENETC is operating as an SR-IOV multi-PF capable Root Complex Integrated
Endpoint (RCIE). As such, it contains multiple physical (PF) and
virtual (VF) PCIe functions, discoverable by standard PCI Express.
Introduce basic PF and VF ENETC ethernet drivers. The PF has access to
the ENETC Port registers and resources and makes the required privileged
configurations for the underlying VF devices. Common functionality is
controlled through so called System Interface (SI) register blocks, PFs
and VFs own a SI each. Though SI register blocks are almost identical,
there are a few privileged SI level controls that are accessible only to
PFs, and so the distinction is made between PF SIs (PSI) and VF SIs (VSI).
As such, the bulk of the code, including datapath processing, basic h/w
offload support and generic pci related configuration, is shared between
the 2 drivers and is factored out in common source files (i.e. enetc.c).
Major functionalities included (for both drivers):
MSI-X support for Rx and Tx processing, assignment of Rx/Tx BD ring pairs
to MSI-X entries, multi-queue support, Rx S/G (Rx frame fragmentation) and
jumbo frame (up to 9600B) support, Rx paged allocation and reuse, Tx S/G
support (NETIF_F_SG), Rx and Tx checksum offload, PF MAC filtering and
initial control ring support, VLAN extraction/ insertion, PF Rx VLAN
CTAG filtering, VF mac address config support, VF VLAN isolation support,
etc.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Soften the memory barrier call of mb() by a sufficient wmb() in the
consumer index update of the event queues.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Procedure mlx4_init_user_cqes() handles returns by copy_to_user
incorrectly. copy_to_user() returns the number of bytes not copied.
Thus, a non-zero return should be treated as a -EFAULT error
(as is done elsewhere in the kernel). However, mlx4_init_user_cqes()
error handling simply returns the number of bytes not copied
(instead of -EFAULT).
Note, though, that this is a harmless bug: procedure mlx4_alloc_cq()
(which is the only caller of mlx4_init_user_cqes()) treats any
non-zero return as an error, but that returned error value is processed
internally, and not passed further up the call stack.
In addition, fixes the following sparse warning:
warning: incorrect type in argument 1 (different address spaces)
expected void [noderef] <asn:1>*to
got void *buf
Fixes: e45678973dcb ("{net, IB}/mlx4: Initialize CQ buffers in the driver when possible")
Reported by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver reads the query HCA capabilities without the corresponding masks.
Without the correct masks, the base addresses of the queues are
unaligned. In addition some reserved bits were wrongly read. Using the
correct masks, ensures alignment of the base addresses and allows future
firmware versions safe use of the reserved bits.
Fixes: ab9c17a009ee ("mlx4_core: Modify driver initialization flow to accommodate SRIOV for Ethernet")
Fixes: 0ff1fb654bec ("{NET, IB}/mlx4: Add device managed flow steering firmware API")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now sctp_transport_pmtu() passes transport->saddr into .get_dst() to set
flow sport from 'saddr'. However, transport->saddr is set only when
transport->dst exists in sctp_transport_route().
If sctp_transport_pmtu() is called without transport->saddr set, like
when transport->dst doesn't exists, the flow sport will be set to 0
from transport->saddr, which will cause a wrong route to be got.
Commit 6e91b578bf3f ("sctp: re-use sctp_transport_pmtu in
sctp_transport_route") made the issue be triggered more easily
since sctp_transport_pmtu() would be called in sctp_transport_route()
after that.
In gerneral, fl4->fl4_sport should always be set to
htons(asoc->base.bind_addr.port), unless transport->asoc doesn't exist
in sctp_v4/6_get_dst(), which is the case:
sctp_ootb_pkt_new() ->
sctp_transport_route()
For that, we can simply handle it by setting flow sport from saddr only
when it's 0 in sctp_v4/6_get_dst().
Fixes: 6e91b578bf3f ("sctp: re-use sctp_transport_pmtu in sctp_transport_route")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the paths:
sctp_sf_do_unexpected_init() ->
sctp_make_init_ack()
sctp_sf_do_dupcook_a/b()() ->
sctp_sf_do_5_1D_ce()
The new chunk 'retval' transport is set from the incoming chunk 'chunk'
transport. However, 'retval' transport belong to the new asoc, which
is a different one from 'chunk' transport's asoc.
It will cause that the 'retval' chunk gets set with a wrong transport.
Later when sending it and because of Commit b9fd683982c9 ("sctp: add
sctp_packet_singleton"), sctp_packet_singleton() will set some fields,
like vtag to 'retval' chunk from that wrong transport's asoc.
This patch is to fix it by setting 'retval' transport correctly which
belongs to the right asoc in sctp_make_init_ack() and
sctp_sf_do_5_1D_ce().
Fixes: b9fd683982c9 ("sctp: add sctp_packet_singleton")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to improve sctp stream adding events in 2 places:
1. In sctp_process_strreset_addstrm_out(), move up SCTP_MAX_STREAM
and in stream allocation failure checks, as the adding has to
succeed after reconf_timer stops for the in stream adding
request retransmission.
3. In sctp_process_strreset_addstrm_in(), no event should be sent,
as no in or out stream is added here.
Fixes: 50a41591f110 ("sctp: implement receiver-side procedures for the Add Outgoing Streams Request Parameter")
Fixes: c5c4ebb3ab87 ("sctp: implement receiver-side procedures for the Add Incoming Streams Request Parameter")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to improve sctp stream reset events in 4 places:
1. In sctp_process_strreset_outreq(), the flag should always be set with
SCTP_STREAM_RESET_INCOMING_SSN instead of OUTGOING, as receiver's in
stream is reset here.
2. In sctp_process_strreset_outreq(), move up SCTP_STRRESET_ERR_WRONG_SSN
check, as the reset has to succeed after reconf_timer stops for the
in stream reset request retransmission.
3. In sctp_process_strreset_inreq(), no event should be sent, as no in
or out stream is reset here.
4. In sctp_process_strreset_resp(), SCTP_STREAM_RESET_INCOMING_SSN or
OUTGOING event should always be sent for stream reset requests, no
matter it fails or succeeds to process the request.
Fixes: 810544764536 ("sctp: implement receiver-side procedures for the Outgoing SSN Reset Request Parameter")
Fixes: 16e1a91965b0 ("sctp: implement receiver-side procedures for the Incoming SSN Reset Request Parameter")
Fixes: 11ae76e67a17 ("sctp: implement receiver-side procedures for the Reconf Response Parameter")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|