aboutsummaryrefslogtreecommitdiffstats
path: root/arch (follow)
AgeCommit message (Collapse)AuthorFilesLines
2017-10-09Merge branch 'ppc-bundle' (bundle from Michael Ellerman)Linus Torvalds2-2/+35
Merge powerpc transactional memory fixes from Michael Ellerman: "I figured I'd still send you the commits using a bundle to make sure it works in case I need to do it again in future" This fixes transactional memory state restore for powerpc. * bundle'd patches from Michael Ellerman: powerpc/tm: Fix illegal TM state in signal handler powerpc/64s: Use emergency stack for kernel TM Bad Thing program checks
2017-10-09Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds2-4/+0
Pull networking fixes from David Miller: 1) Fix object leak on IPSEC offload failure, from Steffen Klassert. 2) Fix range checks in ipset address range addition operations, from Jozsef Kadlecsik. 3) Fix pernet ops unregistration order in ipset, from Florian Westphal. 4) Add missing netlink attribute policy for nl80211 packet pattern attrs, from Peng Xu. 5) Fix PPP device destruction race, from Guillaume Nault. 6) Write marks get lost when BPF verifier processes R1=R2 register assignments, causing incorrect liveness information and less state pruning. Fix from Alexei Starovoitov. 7) Fix blockhole routes so that they are marked dead and therefore not cached in sockets, otherwise IPSEC stops working. From Steffen Klassert. 8) Fix broadcast handling of UDP socket early demux, from Paolo Abeni. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (37 commits) cdc_ether: flag the u-blox TOBY-L2 and SARA-U2 as wwan net: thunderx: mark expected switch fall-throughs in nicvf_main() udp: fix bcast packet reception netlink: do not set cb_running if dump's start() errs ipv4: Fix traffic triggered IPsec connections. ipv6: Fix traffic triggered IPsec connections. ixgbe: incorrect XDP ring accounting in ethtool tx_frame param net: ixgbe: Use new PCI_DEV_FLAGS_NO_RELAXED_ORDERING flag Revert commit 1a8b6d76dc5b ("net:add one common config...") ixgbe: fix masking of bits read from IXGBE_VXLANCTRL register ixgbe: Return error when getting PHY address if PHY access is not supported netfilter: xt_bpf: Fix XT_BPF_MODE_FD_PINNED mode of 'xt_bpf_info_v1' netfilter: SYNPROXY: skip non-tcp packet in {ipv4, ipv6}_synproxy_hook tipc: Unclone message at secondary destination lookup tipc: correct initialization of skb list gso: fix payload length when gso_size is zero mlxsw: spectrum_router: Avoid expensive lookup during route removal bpf: fix liveness marking doc: Fix typo "8023.ad" in bonding documentation ipv6: fix net.ipv6.conf.all.accept_dad behaviour for real ...
2017-10-09Revert commit 1a8b6d76dc5b ("net:add one common config...")Ding Tianhong2-4/+0
The new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING has been added to indicate that Relaxed Ordering Attributes (RO) should not be used for Transaction Layer Packets (TLP) targeted toward these affected Root Port, it will clear the bit4 in the PCIe Device Control register, so the PCIe device drivers could query PCIe configuration space to determine if it can send TLPs to Root Port with the Relaxed Ordering Attributes set. With this new flag we don't need the config ARCH_WANT_RELAX_ORDER to control the Relaxed Ordering Attributes for the ixgbe drivers just like the commit 1a8b6d76dc5b ("net:add one common config...") did, so revert this commit. Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2017-10-06Merge tag 'arc-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arcLinus Torvalds16-27/+128
Pull ARC udpates from Vineet Gupta: - updates for various platforms - boot log updates for upcoming HS48 family of cores (dual issue) * tag 'arc-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: ARC: [plat-hsdk]: Add reset controller node to manage ethernet reset ARC: [plat-hsdk]: Temporary fix to set CPU frequency to 1GHz ARC: fix allnoconfig build warning ARCv2: boot log: identify HS48 cores (dual issue) ARC: boot log: decontaminate ARCv2 ISA_CONFIG register arc: remove redundant UTS_MACHINE define in arch/arc/Makefile ARC: [plat-eznps] Update platform maintainer as Noam left ARC: [plat-hsdk] use actual clk driver to manage cpu clk ARC: [*defconfig] Reenable soft lock-up detector ARC: [plat-axs10x] sdio: Temporary fix of sdio ciu frequency ARC: [plat-hsdk] sdio: Temporary fix of sdio ciu frequency ARC: [plat-axs103] Add temporary quirk to reset ethernet IP
2017-10-06Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linuxLinus Torvalds5-7/+10
Pull arm64 fixes from Catalin Marinas: - Bring initialisation of user space undefined instruction handling early (core_initcall) since late_initcall() happens after modprobe in initramfs is invoked. Similar fix for fpsimd initialisation - Increase the kernel stack when KASAN is enabled - Bring the PCI ACS enabling earlier via the iort_init_platform_devices() - Fix misleading data abort address printing (decimal vs hex) * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: arm64: Ensure fpsimd support is ready before userspace is active arm64: Ensure the instruction emulation is ready for userspace arm64: Use larger stacks when KASAN is selected ACPI/IORT: Fix PCI ACS enablement arm64: fix misleading data abort decoding
2017-10-06Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds7-13/+20
Pull KVM fixes from Radim Krčmář: - fix PPC XIVE interrupt delivery - fix x86 RCU breakage from asynchronous page faults when built without PREEMPT_COUNT - fix x86 build with -frecord-gcc-switches - fix x86 build without X86_LOCAL_APIC * tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: KVM: add X86_LOCAL_APIC dependency x86/kvm: Move kvm_fastop_exception to .fixup section kvm/x86: Avoid async PF preempting the kernel incorrectly KVM: PPC: Book3S: Fix server always zero from kvmppc_xive_get_xive()
2017-10-06ARC: [plat-hsdk]: Add reset controller node to manage ethernet resetEugeniy Paltsev2-0/+10
DW ethernet controller on HSDK hangs sometimes after SW reset, so add reset node to make possible to reset DW ethernet controller HW. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
2017-10-06Merge tag 'powerpc-4.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linuxLinus Torvalds7-7/+37
Pull powerpc fixes from Michael Ellerman: "Nine small fixes, really nothing that stands out. A work-around for a spurious MCE on Power9. A CXL fault handling fix, some fixes to the new XIVE code, and a fix to the new 32-bit STRICT_KERNEL_RWX code. Fixes for old code/stable: an fix to an incorrect TLB flush on boot but not on any current machines, a compile error on 4xx and a fix to memory hotplug when using radix (Power9). Thanks to: Anton Blanchard, Cédric Le Goater, Christian Lamparter, Christophe Leroy, Christophe Lombard, Guenter Roeck, Jeremy Kerr, Michael Neuling, Nicholas Piggin" * tag 'powerpc-4.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/powernv: Increase memory block size to 1GB on radix powerpc/mm: Call flush_tlb_kernel_range with interrupts enabled powerpc/xive: Clear XIVE internal structures when a CPU is removed powerpc/xive: Fix IPI reset powerpc/4xx: Fix compile error with 64K pages on 40x, 44x powerpc: Fix action argument for cpufeatures-based TLB flush cxl: Fix memory page not handled powerpc: Fix workaround for spurious MCE on POWER9 powerpc: Handle MCE on POWER9 with only DSISR bit 30 set
2017-10-06Merge branch 'core-watchdog-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds3-23/+20
Pull watchddog clean-up and fixes from Thomas Gleixner: "The watchdog (hard/softlockup detector) code is pretty much broken in its current state. The patch series addresses this by removing all duct tape and refactoring it into a workable state. The reasons why I ask for inclusion that late in the cycle are: 1) The code causes lockdep splats vs. hotplug locking which get reported over and over. Unfortunately there is no easy fix. 2) The risk of breakage is minimal because it's already broken 3) As 4.14 is a long term stable kernel, I prefer to have working watchdog code in that and the lockdep issues resolved. I wouldn't ask you to pull if 4.14 wouldn't be a LTS kernel or if the solution would be easy to backport. 4) The series was around before the merge window opened, but then got delayed due to the UP failure caused by the for_each_cpu() surprise which we discussed recently. Changes vs. V1: - Addressed your review points - Addressed the warning in the powerpc code which was discovered late - Changed two function names which made sense up to a certain point in the series. Now they match what they do in the end. - Fixed a 'unused variable' warning, which got not detected by the intel robot. I triggered it when trying all possible related config combinations manually. Randconfig testing seems not random enough. The changes have been tested by and reviewed by Don Zickus and tested and acked by Micheal Ellerman for powerpc" * 'core-watchdog-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits) watchdog/core: Put softlockup_threads_initialized under ifdef guard watchdog/core: Rename some softlockup_* functions powerpc/watchdog: Make use of watchdog_nmi_probe() watchdog/core, powerpc: Lock cpus across reconfiguration watchdog/core, powerpc: Replace watchdog_nmi_reconfigure() watchdog/hardlockup/perf: Fix spelling mistake: "permanetely" -> "permanently" watchdog/hardlockup/perf: Cure UP damage watchdog/hardlockup: Clean up hotplug locking mess watchdog/hardlockup/perf: Simplify deferred event destroy watchdog/hardlockup/perf: Use new perf CPU enable mechanism watchdog/hardlockup/perf: Implement CPU enable replacement watchdog/hardlockup/perf: Implement init time detection of perf watchdog/hardlockup/perf: Implement init time perf validation watchdog/core: Get rid of the racy update loop watchdog/core, powerpc: Make watchdog_nmi_reconfigure() two stage watchdog/sysctl: Clean up sysctl variable name space watchdog/sysctl: Get rid of the #ifdeffery watchdog/core: Clean up header mess watchdog/core: Further simplify sysctl handling watchdog/core: Get rid of the thread teardown/setup dance ...
2017-10-06arm64: Ensure fpsimd support is ready before userspace is activeSuzuki K Poulose1-1/+1
We register the pm/hotplug callbacks for FPSIMD as late_initcall, which happens after the userspace is active (from initramfs via populate_rootfs, a rootfs_initcall). Make sure we are ready even before the userspace could potentially use it, by promoting to a core_initcall. Cc: Will Deacon <will.deacon@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Dave Martin <dave.martin@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2017-10-06arm64: Ensure the instruction emulation is ready for userspaceSuzuki K Poulose2-2/+2
We trap and emulate some instructions (e.g, mrs, deprecated instructions) for the userspace. However the handlers for these are registered as late_initcalls and the userspace could be up and running from the initramfs by that time (with populate_rootfs, which is a rootfs_initcall()). This could cause problems for the early applications ending up in failure like : [ 11.152061] modprobe[93]: undefined instruction: pc=0000ffff8ca48ff4 This patch promotes the specific calls to core_initcalls, which are guaranteed to be completed before we hit userspace. Cc: stable@vger.kernel.org Cc: Dave Martin <dave.martin@arm.com> Cc: Matthias Brugger <mbrugger@suse.com> Cc: James Morse <james.morse@arm.com> Reported-by: Matwey V. Kornilov <matwey.kornilov@gmail.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2017-10-06powerpc/tm: Fix illegal TM state in signal handlerGustavo Romero1-1/+12
Currently it's possible that on returning from the signal handler through the restore_tm_sigcontexts() code path (e.g. from a signal caught due to a `trap` instruction executed in the middle of an HTM block, or a deliberately constructed sigframe) an illegal TM state (like TS=10 TM=0, i.e. "T0") is set in SRR1 and when `rfid` sets implicitly the MSR register from SRR1 register on return to userspace it causes a TM Bad Thing exception. That illegal state can be set (a) by a malicious user that disables the TM bit by tweaking the bits in uc_mcontext before returning from the signal handler or (b) by a sufficient number of context switches occurring such that the load_tm counter overflows and TM is disabled whilst in the signal handler. This commit fixes the illegal TM state by ensuring that TM bit is always enabled before we return from restore_tm_sigcontexts(). A small comment correction is made as well. Fixes: 5d176f751ee3 ("powerpc: tm: Enable transactional memory (TM) lazily for userspace") Cc: stable@vger.kernel.org # v4.9+ Signed-off-by: Gustavo Romero <gromero@linux.vnet.ibm.com> Signed-off-by: Breno Leitao <leitao@debian.org> Signed-off-by: Cyril Bur <cyrilbur@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-10-06powerpc/64s: Use emergency stack for kernel TM Bad Thing program checksCyril Bur1-1/+23
When using transactional memory (TM), the CPU can be in one of six states as far as TM is concerned, encoded in the Machine State Register (MSR). Certain state transitions are illegal and if attempted trigger a "TM Bad Thing" type program check exception. If we ever hit one of these exceptions it's treated as a bug, ie. we oops, and kill the process and/or panic, depending on configuration. One case where we can trigger a TM Bad Thing, is when returning to userspace after a system call or interrupt, using RFID. When this happens the CPU first restores the user register state, in particular r1 (the stack pointer) and then attempts to update the MSR. However the MSR update is not allowed and so we take the program check with the user register state, but the kernel MSR. This tricks the exception entry code into thinking we have a bad kernel stack pointer, because the MSR says we're coming from the kernel, but r1 is pointing to userspace. To avoid this we instead always switch to the emergency stack if we take a TM Bad Thing from the kernel. That way none of the user register values are used, other than for printing in the oops message. This is the fix for CVE-2017-1000255. Fixes: 5d176f751ee3 ("powerpc: tm: Enable transactional memory (TM) lazily for userspace") Cc: stable@vger.kernel.org # v4.9+ Signed-off-by: Cyril Bur <cyrilbur@gmail.com> [mpe: Rewrite change log & comments, tweak asm slightly] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-10-06powerpc/powernv: Increase memory block size to 1GB on radixAnton Blanchard1-1/+9
Memory hot unplug on PowerNV radix hosts is broken. Our memory block size is 256MB but since we map the linear region with very large pages, each pte we tear down maps 1GB. A hot unplug of one 256MB memory block results in 768MB of memory getting unintentionally unmapped. At this point we are likely to oops. Fix this by increasing our memory block size to 1GB on PowerNV radix hosts. Fixes: 4b5d62ca17a1 ("powerpc/mm: add radix__remove_section_mapping()") Cc: stable@vger.kernel.org # v4.11+ Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-10-05KVM: add X86_LOCAL_APIC dependencyArnd Bergmann1-0/+1
The rework of the posted interrupt handling broke building without support for the local APIC: ERROR: "boot_cpu_physical_apicid" [arch/x86/kvm/kvm-intel.ko] undefined! That configuration is probably not particularly useful anyway, so we can avoid the randconfig failures by adding a Kconfig dependency. Fixes: 8b306e2f3c41 ("KVM: VMX: avoid double list add with VT-d posted interrupts") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
2017-10-05Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds1-2/+2
Pull networking fixes from David Miller: 1) Check iwlwifi 9000 reorder buffer out-of-space condition properly, from Sara Sharon. 2) Fix RCU splat in qualcomm rmnet driver, from Subash Abhinov Kasiviswanathan. 3) Fix session and tunnel release races in l2tp, from Guillaume Nault and Sabrina Dubroca. 4) Fix endian bug in sctp_diag_dump(), from Dan Carpenter. 5) Several mlx5 driver fixes from the Mellanox folks (max flow counters cap check, invalid memory access in IPoIB support, etc.) 6) tun_get_user() should bail if skb->len is zero, from Alexander Potapenko. 7) Fix RCU lookups in inetpeer, from Eric Dumazet. 8) Fix locking in packet_do_bund(). 9) Handle cb->start() error properly in netlink dump code, from Jason A. Donenfeld. 10) Handle multicast properly in UDP socket early demux code. From Paolo Abeni. 11) Several erspan bug fixes in ip_gre, from Xin Long. 12) Fix use-after-free in socket filter code, in order to handle the fact that listener lock is no longer taken during the three-way TCP handshake. From Eric Dumazet. 13) Fix infoleak in RTM_GETSTATS, from Nikolay Aleksandrov. 14) Fix tail call generation in x86-64 BPF JIT, from Alexei Starovoitov. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (77 commits) net: 8021q: skip packets if the vlan is down bpf: fix bpf_tail_call() x64 JIT net: stmmac: dwmac-rk: Add RK3128 GMAC support rndis_host: support Novatel Verizon USB730L net: rtnetlink: fix info leak in RTM_GETSTATS call socket, bpf: fix possible use after free mlxsw: spectrum_router: Track RIF of IPIP next hops mlxsw: spectrum_router: Move VRF refcounting net: hns3: Fix an error handling path in 'hclge_rss_init_hw()' net: mvpp2: Fix clock resource by adding an optional bus clock r8152: add Linksys USB3GIGV1 id l2tp: fix l2tp_eth module loading ip_gre: erspan device should keep dst ip_gre: set tunnel hlen properly in erspan_tunnel_init ip_gre: check packet length and mtu correctly in erspan_xmit ip_gre: get key from session_id correctly in erspan_rcv tipc: use only positive error codes in messages ppp: fix __percpu annotation udp: perform source validation for mcast early demux IPv4: early demux can return an error code ...
2017-10-05x86/kvm: Move kvm_fastop_exception to .fixup sectionJosh Poimboeuf1-2/+4
When compiling the kernel with the '-frecord-gcc-switches' flag, objtool complains: arch/x86/kvm/emulate.o: warning: objtool: .GCC.command.line+0x0: special: can't find new instruction And also the kernel fails to link. The problem is that the 'kvm_fastop_exception' code gets placed into the throwaway '.GCC.command.line' section instead of '.text'. Exception fixup code is conventionally placed in the '.fixup' section, so put it there where it belongs. Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
2017-10-04Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds37-456/+728
Pull ARM SoC fixes from Olof Johansson: "Our first batch of fixes this release cycle, unfortunately a bit noisier than usual. Two major groups stand out: - Some pinctril dts/dtsi changes for stm32 due to a new driver being merged during the merge window, and this aligns the DT contents between the old format and the new. This could arguably be moved to the next merge window but it also seemed relatively harmless to include now. - Amlogic/meson had driver changes merged that required devicetree changes to avoid functional/performance regressions. I've already asked them to be more careful about this going forward, and making sure drivers are compatible with older DTs when they make these kind of changes. The platform is actively being upstreamed so there's a few things in flight, we've seen this happen before and sometimes it's hard to catch in time. Besides that there is the usual mix of minor fixes" * tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits) ARM: dts: stm32: use right pinctrl compatible for stm32f469 ARM: dts: stm32: Fix STMPE1600 binding on stm32429i-eval board ARM: defconfig: update Gemini defconfig ARM: defconfig: FRAMEBUFFER_CONSOLE can no longer be =m arm64: dts: rockchip: add the grf clk for dw-mipi-dsi on rk3399 reset: Restrict RESET_HSDK to ARC_SOC_HSDK or COMPILE_TEST ARM: dts: da850-evm: add serial and ethernet aliases ARM: dts: am43xx-epos-evm: Remove extra CPSW EMAC entry ARM: dts: am33xx: Add spi alias to match SOC schematics ARM: OMAP2+: hsmmc: fix logic to call either omap_hsmmc_init or omap_hsmmc_late_init but not both ARM: dts: dra7: Set a default parent to mcasp3_ahclkx_mux ARM: OMAP2+: dra7xx: Set OPT_CLKS_IN_RESET flag for gpio1 ARM: dts: nokia n900: drop unneeded/undocumented parts of the dts arm64: dts: rockchip: Correct MIPI DPHY PLL clock on rk3399 arm64: dt marvell: Fix AP806 system controller size MAINTAINERS: add Macchiatobin maintainers entry ARC: reset: remove the misleading v1 suffix all over ARC: reset: add missing DT binding documentation for HSDKv1 reset driver ARC: reset: Only build on archs that have IOMEM ARM: at91: Replace uses of virt_to_phys with __pa_symbol ...
2017-10-04Merge tag 'stm32-dt-fixes-for-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into fixesOlof Johansson7-300/+538
STM32 fixes for v4.14: --------------------- -Fix STMPE1600 bindings for stm32429i-eval board -Use right compatible for stm32f469 pinctrl. It implies to use pinctrl dedicated files for F4 SoCs. * tag 'stm32-dt-fixes-for-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: ARM: dts: stm32: use right pinctrl compatible for stm32f469 ARM: dts: stm32: Fix STMPE1600 binding on stm32429i-eval board Signed-off-by: Olof Johansson <olof@lixom.net>
2017-10-04Merge tag 'amlogic-dt64-3' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into fixesOlof Johansson14-49/+150
Amlogic 64-bit DT updates for v4.14 (round 3) - updates for new MMC driver features/fixes - support high-speed modes * tag 'amlogic-dt64-3' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: ARM64: dts: meson-gxbb: nanopi-k2: enable sdr104 mode ARM64: dts: meson-gxbb: nanopi-k2: enable sdcard UHS modes ARM64: dts: meson-gxbb: p20x: enable sdcard UHS modes ARM64: dts: meson-gxl: libretech-cc: enable high speed modes ARM64: dts: meson-gxl: libretech-cc: add card regulator settle times ARM64: dts: meson-gxbb: nanopi-k2: add card regulator settle times ARM64: dts: meson: add mmc clk gate pins ARM64: dts: meson: remove cap-sd-highspeed from emmc nodes ARM64: dts: meson-gx: Use correct mmc clock source 0 Signed-off-by: Olof Johansson <olof@lixom.net>
2017-10-04arm64: Use larger stacks when KASAN is selectedMark Rutland1-3/+6
AddressSanitizer instrumentation can significantly bloat the stack, and with GCC 7 this can result in stack overflows at boot time in some configurations. We can avoid this by doubling our stack size when KASAN is in use, as is already done on x86 (and has been since KASAN was introduced). Regardless of other patches to decrease KASAN's stack utilization, kernels built with KASAN will always require more stack space than those built without, and we should take this into account. Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2017-10-04kvm/x86: Avoid async PF preempting the kernel incorrectlyBoqun Feng3-7/+13
Currently, in PREEMPT_COUNT=n kernel, kvm_async_pf_task_wait() could call schedule() to reschedule in some cases. This could result in accidentally ending the current RCU read-side critical section early, causing random memory corruption in the guest, or otherwise preempting the currently running task inside between preempt_disable and preempt_enable. The difficulty to handle this well is because we don't know whether an async PF delivered in a preemptible section or RCU read-side critical section for PREEMPT_COUNT=n, since preempt_disable()/enable() and rcu_read_lock/unlock() are both no-ops in that case. To cure this, we treat any async PF interrupting a kernel context as one that cannot be preempted, preventing kvm_async_pf_task_wait() from choosing the schedule() path in that case. To do so, a second parameter for kvm_async_pf_task_wait() is introduced, so that we know whether it's called from a context interrupting the kernel, and the parameter is set properly in all the callsites. Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Wanpeng Li <wanpeng.li@hotmail.com> Cc: stable@vger.kernel.org Signed-off-by: Boqun Feng <boqun.feng@gmail.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
2017-10-04ARM: dts: stm32: use right pinctrl compatible for stm32f469Alexandre Torgue7-297/+537
Currently, same stm32f429-pinctrl driver is used for stm32f429 and stm32f469. As pin map is different between those 2 MCUs, a stm32f469-pinctrl driver has been recently added. This patch -allows to use stm32f469-pinctrl driver for stm32f469 boards -reworks stm32 devicetree files to fit with stm32f429 / stm32f469 In the same time it fixes an issue when only MACH_STM32F469 flag is selected in menuconfig. Fixes: d28bcd53fa90 ("ARM: stm32: Introduce MACH_STM32F469 flag") Reported-by: Nicolas Pitre <nicolas.pitre@linaro.org> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2017-10-04powerpc/mm: Call flush_tlb_kernel_range with interrupts enabledGuenter Roeck1-1/+1
flush_tlb_kernel_range() may call smp_call_function_many() which expects interrupts to be enabled. This results in a traceback. WARNING: CPU: 0 PID: 1 at kernel/smp.c:416 smp_call_function_many+0xcc/0x2fc CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.14.0-rc1-00009-g0666f56 #1 task: cf830000 task.stack: cf82e000 NIP: c00a93c8 LR: c00a9634 CTR: 00000001 REGS: cf82fde0 TRAP: 0700 Not tainted (4.14.0-rc1-00009-g0666f56) MSR: 00021000 <CE,ME> CR: 24000082 XER: 00000000 GPR00: c00a9634 cf82fe90 cf830000 c050ad3c c0015a54 00000000 00000001 00000001 GPR08: 00000001 00000000 00000000 cf82e000 24000084 00000000 c0003150 00000000 GPR16: 00000000 00000000 00000000 00000000 00000000 00000001 00000000 c0510000 GPR24: 00000000 c0015a54 00000000 c050ad3c c051823c c050ad3c 00000025 00000000 NIP [c00a93c8] smp_call_function_many+0xcc/0x2fc LR [c00a9634] smp_call_function+0x3c/0x50 Call Trace: [cf82fe90] [00000010] 0x10 (unreliable) [cf82fed0] [c00a9634] smp_call_function+0x3c/0x50 [cf82fee0] [c0015d2c] flush_tlb_kernel_range+0x20/0x38 [cf82fef0] [c001524c] mark_initmem_nx+0x154/0x16c [cf82ff20] [c001484c] free_initmem+0x20/0x4c [cf82ff30] [c000316c] kernel_init+0x1c/0x108 [cf82ff40] [c000f3a8] ret_from_kernel_thread+0x5c/0x64 Instruction dump: 7c0803a6 7d808120 38210040 4e800020 3d20c052 812981a0 2f890000 40beffac 3d20c051 8929ac64 2f890000 40beff9c <0fe00000> 4bffff94 7fc3f378 7f64db78 Fixes: 3184cc4b6f6a ("powerpc/mm: Fix kernel RAM protection after freeing ...") Fixes: e611939fc8ec ("powerpc/mm: Ensure change_page_attr() doesn't ...") Cc: Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-10-04powerpc/xive: Clear XIVE internal structures when a CPU is removedCédric Le Goater1-0/+8
Commit eac1e731b59e ("powerpc/xive: guest exploitation of the XIVE interrupt controller") introduced support for the XIVE exploitation mode of the P9 interrupt controller on the pseries platform. At that time, support for CPU removal was not complete on PowerVM and CPU hot unplug remained untested. It appears that some cleanups of the XIVE internal structures are required before releasing the CPU, without which the kernel crashes in a RTAS call doing the CPU isolation. These changes fix the crash by deconfiguring the IPI interrupt source and clearing the event queues of the CPU when it is removed. Fixes: eac1e731b59e ("powerpc/xive: guest exploitation of the XIVE interrupt controller") Signed-off-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-10-04powerpc/xive: Fix IPI resetCédric Le Goater1-0/+4
When resetting an IPI, hw_ipi should also be set to zero. Fixes: eac1e731b59e ("powerpc/xive: guest exploitation of the XIVE interrupt controller") Signed-off-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-10-04ARM: dts: stm32: Fix STMPE1600 binding on stm32429i-eval boardAlexandre Torgue1-3/+1
To declare gpio interrupt line for STMPE1600, 2 possibilities are offered: -use gpio binding (and then the gpiolib interface inside driver) -use interrupt binding as each gpio-controller are also interrupt controller on stm32f429. In STMPE 1600 node both (gpio and interrupt) bindings are defined. This patch fixes this issue and use only interrupt binding. Fixes: c04b2e72af8d ("ARM: dts: stm32: Enable STMPE1600 gpio expander of STM32F429-EVAL board") Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2017-10-04powerpc/watchdog: Make use of watchdog_nmi_probe()Thomas Gleixner1-9/+8
The rework of the core hotplug code triggers the WARN_ON in start_wd_cpu() on powerpc because it is called multiple times for the boot CPU. The first call is via: start_wd_on_cpu+0x80/0x2f0 watchdog_nmi_reconfigure+0x124/0x170 softlockup_reconfigure_threads+0x110/0x130 lockup_detector_init+0xbc/0xe0 kernel_init_freeable+0x18c/0x37c kernel_init+0x2c/0x160 ret_from_kernel_thread+0x5c/0xbc And then again via the CPU hotplug registration: start_wd_on_cpu+0x80/0x2f0 cpuhp_invoke_callback+0x194/0x620 cpuhp_thread_fun+0x7c/0x1b0 smpboot_thread_fn+0x290/0x2a0 kthread+0x168/0x1b0 ret_from_kernel_thread+0x5c/0xbc This can be avoided by setting up the cpu hotplug state with nocalls and move the initialization to the watchdog_nmi_probe() function. That initializes the hotplug callbacks without invoking the callback and the following core initialization function then configures the watchdog for the online CPUs (in this case CPU0) via softlockup_reconfigure_threads(). Reported-and-tested-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Michael Ellerman <mpe@ellerman.id.au> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: linuxppc-dev@lists.ozlabs.org
2017-10-04watchdog/core, powerpc: Lock cpus across reconfigurationThomas Gleixner1-4/+0
Instead of dropping the cpu hotplug lock after stopping NMI watchdog and threads and reaquiring for restart, the code and the protection rules become more obvious when holding cpu hotplug lock across the full reconfiguration. Suggested-by: Linus Torvalds <torvalds@linuxfoundation.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Michael Ellerman <mpe@ellerman.id.au> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Don Zickus <dzickus@redhat.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: linuxppc-dev@lists.ozlabs.org Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1710022105570.2114@nanos
2017-10-04watchdog/core, powerpc: Replace watchdog_nmi_reconfigure()Thomas Gleixner1-9/+14
The recent cleanup of the watchdog code split watchdog_nmi_reconfigure() into two stages. One to stop the NMI and one to restart it after reconfiguration. That was done by adding a boolean 'run' argument to the code, which is functionally correct but not necessarily a piece of art. Replace it by two explicit functions: watchdog_nmi_stop() and watchdog_nmi_start(). Fixes: 6592ad2fcc8f ("watchdog/core, powerpc: Make watchdog_nmi_reconfigure() two stage") Requested-by: Linus 'Nursing his pet-peeve' Torvalds <torvalds@linuxfoundation.org> Signed-off-by: Thomas 'Mopping up garbage' Gleixner <tglx@linutronix.de> Acked-by: Michael Ellerman <mpe@ellerman.id.au> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Don Zickus <dzickus@redhat.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: linuxppc-dev@lists.ozlabs.org Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1710021957480.2114@nanos
2017-10-03ARC: [plat-hsdk]: Temporary fix to set CPU frequency to 1GHzEugeniy Paltsev1-0/+42
Add temporary fix to HSDK platform code to setup CPU frequency to 1GHz on early boot. We can remove this fix when smart hsdk pll driver will be introduced, see discussion: https://www.mail-archive.com/linux-snps-arc@lists.infradead.org/msg02689.html Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
2017-10-03ARC: fix allnoconfig build warningVineet Gupta1-1/+1
Reported-by: Dmitrii Kolesnichenko <dmitrii@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
2017-10-03ARCv2: boot log: identify HS48 cores (dual issue)Vineet Gupta2-4/+16
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
2017-10-03ARC: boot log: decontaminate ARCv2 ISA_CONFIG registerVineet Gupta2-8/+15
ARCv2 ISA_CONFIG and ARC700_BUILD build config registers are not compatible. cpuinfo_arc had isa info placeholder which was mashup of bits form both. Untangle this by defining it off of ARCv2 ISA info and it is fine even for ARC700 since former is a super set of latter (ARC700 buildonly has 2 bits for atomics and stack check). At runtime, we treat ARCv2 ISA info as a generic placeholder but populate it correctly depending on ARC700 or HS. This paves way for adding more HS specific bits in isa info which was colliding with the extra bits for arc700. Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
2017-10-03arc: remove redundant UTS_MACHINE define in arch/arc/MakefileMasahiro Yamada1-2/+0
The top-level Makefile sets the default of UTS_MACHINE to $(ARCH). If ARCH and UTS_MACHINE match, arch/$(ARCH)/Makefile need not specify UTS_MACHINE explicitly. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
2017-10-03ARC: [plat-hsdk] use actual clk driver to manage cpu clkEugeniy Paltsev2-3/+11
With corresponding clk driver now merged upstream, switch to it. - core_clk now represent the PLL (vs. fixed clk before) - input_clk represent the clk signal src for PLL (basically xtal) Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
2017-10-03ARC: [*defconfig] Reenable soft lock-up detectorAlexey Brodkin7-7/+7
Commit 92e5aae45778 "kernel/watchdog: split up config options" introduced SOFTLOCKUP_DETECTOR which selects LOCKUP_DETECTOR instead of the latter to be selected itself. We need to adjust our defconfigs accordingly. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
2017-10-03ARC: [plat-axs10x] sdio: Temporary fix of sdio ciu frequencyEugeniy Paltsev1-1/+8
DW sdio controller has external ciu clock divider controlled via register in SDIO IP. It divides sdio_ref_clk (which comes from CGU) by 16 for default. So default mmcclk clock (which comes to sdk_in) is 25000000 Hz. So fix wrong current value (50000000 Hz) to actual 25000000 Hz. Note this is a preventive fix, in line with similar change for HSDK where this was actually needed. see: http://lists.infradead.org/pipermail/linux-snps-arc/2017-September/002924.html Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
2017-10-03ARC: [plat-hsdk] sdio: Temporary fix of sdio ciu frequencyEugeniy Paltsev1-1/+11
DW sdio controller has external ciu clock divider controlled via register in SDIO IP. Due to its unexpected default value (it should divide by 1 but it divides by 8) SDIO IP uses wrong ciu clock and works unstable So add temporary fix and change clock frequency from 100000000 to 12500000 Hz until we fix dw sdio driver itself. Fixes SNPS STAR 9001204800 Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
2017-10-03ARC: [plat-axs103] Add temporary quirk to reset ethernet IPEugeniy Paltsev1-0/+7
DW ethernet controller on AXS10x hangs sometimes after SW reset, so add temporary quirk to reset DW ethernet controller IP core. This quirk can be removed after axs10x reset driver (see http://patchwork.ozlabs.org/patch/800273/) or simple reset driver (see https://patchwork.kernel.org/patch/9903375/) will be available in upstream. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
2017-10-03Merge tag 'omap-for-v4.14/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixesOlof Johansson6-18/+8
Fixes for omaps for v4.14-rc cycle Few minor fixes for omaps, mostly just boot time warning fixes: - Drop undocumented camera binding that got merged during the merge window by accident as I applied before Sakari's comments - Fix soft reset warning for dra7 kexec boot for gpio1 as the optional clocks need to be enabled for reset - Fix dra7 kexec boot clock rate for McASP as the rate is no longer the default rate after kexec - Fix omap3 pandora MMC warning during boot - Add am33xx SPI alias like we have on other SoCs - Remove node for non-existing CPSW EMAC Ethernet on am43xx-epos-evm * tag 'omap-for-v4.14/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: dts: am43xx-epos-evm: Remove extra CPSW EMAC entry ARM: dts: am33xx: Add spi alias to match SOC schematics ARM: OMAP2+: hsmmc: fix logic to call either omap_hsmmc_init or omap_hsmmc_late_init but not both ARM: dts: dra7: Set a default parent to mcasp3_ahclkx_mux ARM: OMAP2+: dra7xx: Set OPT_CLKS_IN_RESET flag for gpio1 ARM: dts: nokia n900: drop unneeded/undocumented parts of the dts Signed-off-by: Olof Johansson <olof@lixom.net>
2017-10-03Merge tag 'v4.14-rockchip-dts64fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixesOlof Johansson2-73/+5
Adding the operating points on rk3368 like they were did not end up well for the boards as all of them are missing their cpu supplies, the OPPs actually need to follow the <target min max> format as the regulator is shared between both clusters and the one rk3368 board I have, somehow also doesn't like the higher opps at all - all of which I only realized after I brought my rk3368 board online again, after its bootloader broke. So we revert that OPP addition for now. And also two fixes for the mipi dsi controller on rk3399, which was referencing a clock to high up in the clock-tree so that an intermediate gate could be disabled inadvertently and also needs a clock for its area in the general register files of the rk3399 soc. * tag 'v4.14-rockchip-dts64fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: arm64: dts: rockchip: add the grf clk for dw-mipi-dsi on rk3399 arm64: dts: rockchip: Correct MIPI DPHY PLL clock on rk3399 Revert "arm64: dts: rockchip: Add basic cpu frequencies for RK3368" Signed-off-by: Olof Johansson <olof@lixom.net>
2017-10-03Merge tag 'mvebu-fixes-4.14-1' of git://git.infradead.org/linux-mvebu into fixesOlof Johansson1-2/+2
mvebu fixes for 4.14 (part 1) Update MAINTAINERS for the Macchiatobin board (Armada 8K based) Fix AP806 system controller size on Armada 7K/8K * tag 'mvebu-fixes-4.14-1' of git://git.infradead.org/linux-mvebu: arm64: dt marvell: Fix AP806 system controller size MAINTAINERS: add Macchiatobin maintainers entry Signed-off-by: Olof Johansson <olof@lixom.net>
2017-10-03Merge tag 'davinci-fixes-for-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixesOlof Johansson1-0/+7
A fix for random ethernet mac address problem on DA850 EVM. * tag 'davinci-fixes-for-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci: ARM: dts: da850-evm: add serial and ethernet aliases Signed-off-by: Olof Johansson <olof@lixom.net>
2017-10-03Merge tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixesOlof Johansson2-10/+13
Fixes for 4.14: - three DT fixes for the newly introduced sama5d27_som1_ek board - one treewide modification that didn't touch this new PM code: we synchronize now to be coherent with the other ARM platforms * tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91: ARM: at91: Replace uses of virt_to_phys with __pa_symbol ARM: dts: at91: sama5d27_som1_ek: fix USB host vbus ARM: dts: at91: sama5d27_som1_ek: fix typos ARM: dts: at91: sama5d27_som1_ek: update pinmux/pinconf for LEDs and USB Signed-off-by: Olof Johansson <olof@lixom.net>
2017-10-03ARM: defconfig: update Gemini defconfigLinus Walleij1-1/+2
This updates the Gemini defconfig with drivers merged for v4.13 or v4.14: - ATA driver is merged - DMA driver is merged - RTC driver gets selected from default Kconfig Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
2017-10-03ARM: defconfig: FRAMEBUFFER_CONSOLE can no longer be =mArnd Bergmann3-3/+3
It is no longer possible to load this at runtime, so let's change the few remaining users to have it built-in all the time. arch/arm/configs/zeus_defconfig:115:warning: symbol value 'm' invalid for FRAMEBUFFER_CONSOLE arch/arm/configs/viper_defconfig:116:warning: symbol value 'm' invalid for FRAMEBUFFER_CONSOLE arch/arm/configs/pxa_defconfig:474:warning: symbol value 'm' invalid for FRAMEBUFFER_CONSOLE Reported-by: kernelci.org bot <bot@kernelci.org> Fixes: 6104c37094e7 ("fbcon: Make fbcon a built-time depency for fbdev") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Olof Johansson <olof@lixom.net>
2017-10-03m32r: fix build failureSudip Mukherjee1-0/+9
The allmodconfig build of m32r is failing with the error: lib/mpi/mpih-div.o: In function 'mpihelp_divrem': mpih-div.c:(.text+0x40): undefined reference to 'abort' mpih-div.c:(.text+0x40): relocation truncated to fit: R_M32R_26_PCREL_RELA against undefined symbol 'abort' The function 'abort' was never defined for the m32r architecture. Create 'abort' as is done in other arch like 'arm' and 'unicore32'. Link: http://lkml.kernel.org/r/1506727220-6108-1-git-send-email-sudip.mukherjee@codethink.co.uk Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-10-03m32r: define CPU_BIG_ENDIANSudip Mukherjee1-0/+4
The build of m32r allmodconfig is giving lots of build warnings about: include/linux/byteorder/big_endian.h:7:2: warning: #warning inconsistent configuration, needs CONFIG_CPU_BIG_ENDIAN [-Wcpp] #warning inconsistent configuration, needs CONFIG_CPU_BIG_ENDIAN Define CPU_BIG_ENDIAN like the way CPU_LITTLE_ENDIAN is defined. Link: http://lkml.kernel.org/r/1505678083-10320-1-git-send-email-sudipm.mukherjee@gmail.com Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-10-03rapidio: remove global irq spinlocks from the subsystemIoan Nicu2-2/+23
Locking of config and doorbell operations should be done only if the underlying hardware requires it. This patch removes the global spinlocks from the rapidio subsystem and moves them to the mport drivers (fsl_rio and tsi721), only to the necessary places. For example, local config space read and write operations (lcread/lcwrite) are atomic in all existing drivers, so there should be no need for locking, while the cread/cwrite operations which generate maintenance transactions need to be synchronized with a lock. Later, each driver could chose to use a per-port lock instead of a global one, or even more granular locking. Link: http://lkml.kernel.org/r/20170824113023.GD50104@nokia.com Signed-off-by: Ioan Nicu <ioan.nicu.ext@nokia.com> Signed-off-by: Frank Kunz <frank.kunz@nokia.com> Acked-by: Alexandre Bounine <alexandre.bounine@idt.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>