| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull MIPS updates from Paul Burton:
- Support for the MIPSr6 MemoryMapID register & Global INValidate TLB
(GINVT) instructions, allowing for more efficient TLB maintenance
when running on a CPU such as the I6500 that supports these.
- Enable huge page support for MIPS64r6.
- Optimize post-DMA cache sync by removing that code entirely for
kernel configurations in which we know it won't be needed.
- The number of pages allocated for interrupt stacks is now calculated
correctly, where before we would wastefully allocate too much memory
in some configurations.
- The ath79 platform migrates to devicetree.
- The bcm47xx platform sees fixes for the Buffalo WHR-G54S board.
- The ingenic/jz4740 platform gains support for appended devicetrees.
- The cavium_octeon, lantiq, loongson32 & sgi-ip27 platforms all see
cleanups as do various pieces of core architecture code.
* tag 'mips_5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (66 commits)
MIPS: lantiq: Remove separate GPHY Firmware loader
MIPS: ingenic: Add support for appended devicetree
MIPS: SGI-IP27: rework HUB interrupts
MIPS: SGI-IP27: do boot CPU init later
MIPS: SGI-IP27: do xtalk scanning later
MIPS: SGI-IP27: use pr_info/pr_emerg and pr_cont to fix output
MIPS: SGI-IP27: clean up bridge access and header files
MIPS: SGI-IP27: get rid of volatile and hubreg_t
MIPS: irq: Allocate accurate order pages for irq stack
MIPS: dma-noncoherent: Remove bogus condition in dma_sync_phys()
MIPS: eBPF: Remove REG_32BIT_ZERO_EX
MIPS: eBPF: Always return sign extended 32b values
MIPS: CM: Fix indentation
MIPS: BCM47XX: Fix/improve Buffalo WHR-G54S support
MIPS: OCTEON: program rx/tx-delay always from DT
MIPS: OCTEON: delete board-specific link status
MIPS: OCTEON: don't lie about interface type of CN3005 board
MIPS: OCTEON: warn if deprecated link status is being used
MIPS: OCTEON: add fixed-link nodes to in-kernel device tree
MIPS: Delete unused flush_cache_sigtramp()
...
|
|
Pull parisc updates from Helge Deller:
"The most important changes in this patch set are:
- DMA-related cleanups for parisc with the aim to move anything not
required by drivers out of <asm/dma-mapping.h>, by Christoph
Hellwig
- Switch to memblock_alloc(), by Mike Rapoport
- Makefile cleanups by Masahiro Yamada
- Switch to bust_spinlocks(), by Sergey Senozhatsky
- Improved initial SMP affinity selection for IRQs
- Added IPI- and rescheduling interrupts in /proc/interrupts output"
* 'parisc-5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux: (21 commits)
parisc: use memblock_alloc() instead of custom get_memblock()
parisc: Add constants for various PDC firmware calls
parisc: Add constant for PDC_PAT_COMPLEX firmware call
parisc: Show machine product number during boot
parisc: Add constants for PDC_RELOCATE PDC call
parisc: Add PDC_CRASH_PREP PDC function number
parisc: Use F_EXTEND() macro in iosapic code
parisc: remove the HBA_DATA macro
parisc/lba_pci: use container_of in LBA_DEV
parisc/dino: use container_of in DINO_DEV
parisc: properly type the return value of parisc_walk_tree
parisc: properly type the iommu field in struct pci_hba_data
parisc: turn GET_IOC into an inline function
parisc: move internal implementation details out of <asm/dma-mapping.h>
parisc: don't include <asm/cacheflush.h> in <asm/dma-mapping.h>
parisc: remove meaningless ccflags-y in arch/parisc/boot/Makefile
parisc: replace oops_in_progress manipulation with bust_spinlocks()
parisc: Improve initial IRQ to CPU assignment
parisc: Count IPI function call interrupts
parisc: Show rescheduling interrupts on SMP machines only
...
|
|
Pull s390 updates from Martin Schwidefsky:
- A copy of Arnds compat wrapper generation series
- Pass information about the KVM guest to the host in form the control
program code and the control program version code
- Map IOV resources to support PCI physical functions on s390
- Add vector load and store alignment hints to improve performance
- Use the "jdd" constraint with gcc 9 to make jump labels working again
- Remove amode workaround for old z/VM releases from the DCSS code
- Add support for in-kernel performance measurements using the CPU
measurement counter facility
- Introduce a new PMU device cpum_cf_diag to capture counters and store
thenn as event raw data.
- Bug fixes and cleanups
* tag 's390-5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (54 commits)
Revert "s390/cpum_cf: Add kernel message exaplanations"
s390/dasd: fix read device characteristic with CONFIG_VMAP_STACK=y
s390/suspend: fix prefix register reset in swsusp_arch_resume
s390: warn about clearing als implied facilities
s390: allow overriding facilities via command line
s390: clean up redundant facilities list setup
s390/als: remove duplicated in-place implementation of stfle
s390/cio: Use cpa range elsewhere within vfio-ccw
s390/cio: Fix vfio-ccw handling of recursive TICs
s390: vfio_ap: link the vfio_ap devices to the vfio_ap bus subsystem
s390/cpum_cf: Handle EBUSY return code from CPU counter facility reservation
s390/cpum_cf: Add kernel message exaplanations
s390/cpum_cf_diag: Add support for s390 counter facility diagnostic trace
s390/cpum_cf: add ctr_stcctm() function
s390/cpum_cf: move common functions into a separate file
s390/cpum_cf: introduce kernel_cpumcf_avail() function
s390/cpu_mf: replace stcctm5() with the stcctm() function
s390/cpu_mf: add store cpu counter multiple instruction support
s390/cpum_cf: Add minimal in-kernel interface for counter measurements
s390/cpum_cf: introduce kernel_cpumcf_alert() to obtain measurement alerts
...
|
|
Pull m68k updates from Geert Uytterhoeven:
- VLA removal
- gcc-8.x build fixes
- small improvements and cleanups
- defconfig updates
* tag 'm68k-for-v5.1-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Add -ffreestanding to CFLAGS
m68k/apollo: Fix comment in Makefile
dio: Fix buffer overflow in case of unknown board
m68k/defconfig: Update defconfigs for v5.0-rc1
m68k/atari: Avoid VLA use in atari_switches_setup()
m68k: Avoid VLA use in mangle_kernel_stack()
m68k/mac: Use '030 reset method on SE/30
m68k/mac: Remove obsolete comment
m68k/mac: Skip VIA port setup unless RTC is connected
m68k/mac: Clean up unused timer definitions
m68k/defconfig: Drop NET_VENDOR_<FOO>=n
|
|
Linux supports ELF binaries for ~25 years now. a.out coredumping has
bitrotten quite significantly and would need some fixing to get it into
shape again but considering how even the toolchains cannot create a.out
executables in its default configuration, let's deprecate a.out support
and remove it a couple of releases later, instead.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Richard Weinberger <richard@nod.at>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Jann Horn <jannh@google.com>
Cc: <linux-api@vger.kernel.org>
Cc: <linux-fsdevel@vger.kernel.org>
Cc: lkml <linux-kernel@vger.kernel.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <x86@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We're (finally) phasing out a.out support for good. As Borislav Petkov
points out, we've supported ELF binaries for about 25 years by now, and
coredumping in particular has bitrotted over the years.
None of the tool chains even support generating a.out binaries any more,
and the plan is to deprecate a.out support entirely for the kernel. But
I want to start with just removing the core dumping code, because I can
still imagine that somebody actually might want to support a.out as a
simpler biinary format.
Particularly if you generate some random binaries on the fly, ELF is a
much more complicated format (admittedly ELF also does have a lot of
toolchain support, mitigating that complexity a lot and you really
should have moved over in the last 25 years).
So it's at least somewhat possible that somebody out there has some
workflow that still involves generating and running a.out executables.
In contrast, it's very unlikely that anybody depends on debugging any
legacy a.out core files. But regardless, I want this phase-out to be
done in two steps, so that we can resurrect a.out support (if needed)
without having to resurrect the core file dumping that is almost
certainly not needed.
Jann Horn pointed to the <asm/a.out-core.h> file that my first trivial
cut at this had missed.
And Alan Cox points out that the a.out binary loader _could_ be done in
user space if somebody wants to, but we might keep just the loader in
the kernel if somebody really wants it, since the loader isn't that big
and has no really odd special cases like the core dumping does.
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Cc: Jann Horn <jannh@google.com>
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull crypto update from Herbert Xu:
"API:
- Add helper for simple skcipher modes.
- Add helper to register multiple templates.
- Set CRYPTO_TFM_NEED_KEY when setkey fails.
- Require neither or both of export/import in shash.
- AEAD decryption test vectors are now generated from encryption
ones.
- New option CONFIG_CRYPTO_MANAGER_EXTRA_TESTS that includes random
fuzzing.
Algorithms:
- Conversions to skcipher and helper for many templates.
- Add more test vectors for nhpoly1305 and adiantum.
Drivers:
- Add crypto4xx prng support.
- Add xcbc/cmac/ecb support in caam.
- Add AES support for Exynos5433 in s5p.
- Remove sha384/sha512 from artpec7 as hardware cannot do partial
hash"
[ There is a merge of the Freescale SoC tree in order to pull in changes
required by patches to the caam/qi2 driver. ]
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (174 commits)
crypto: s5p - add AES support for Exynos5433
dt-bindings: crypto: document Exynos5433 SlimSSS
crypto: crypto4xx - add missing of_node_put after of_device_is_available
crypto: cavium/zip - fix collision with generic cra_driver_name
crypto: af_alg - use struct_size() in sock_kfree_s()
crypto: caam - remove redundant likely/unlikely annotation
crypto: s5p - update iv after AES-CBC op end
crypto: x86/poly1305 - Clear key material from stack in SSE2 variant
crypto: caam - generate hash keys in-place
crypto: caam - fix DMA mapping xcbc key twice
crypto: caam - fix hash context DMA unmap size
hwrng: bcm2835 - fix probe as platform device
crypto: s5p-sss - Use AES_BLOCK_SIZE define instead of number
crypto: stm32 - drop pointless static qualifier in stm32_hash_remove()
crypto: chelsio - Fixed Traffic Stall
crypto: marvell - Remove set but not used variable 'ivsize'
crypto: ccp - Update driver messages to remove some confusion
crypto: adiantum - add 1536 and 4096-byte test vectors
crypto: nhpoly1305 - add a test vector with len % 16 != 0
crypto: arm/aes-ce - update IV after partial final CTR block
...
|
|
Pull networking updates from David Miller:
"Here we go, another merge window full of networking and #ebpf changes:
1) Snoop DHCPACKS in batman-adv to learn MAC/IP pairs in the DHCP
range without dealing with floods of ARP traffic, from Linus
Lüssing.
2) Throttle buffered multicast packet transmission in mt76, from
Felix Fietkau.
3) Support adaptive interrupt moderation in ice, from Brett Creeley.
4) A lot of struct_size conversions, from Gustavo A. R. Silva.
5) Add peek/push/pop commands to bpftool, as well as bash completion,
from Stanislav Fomichev.
6) Optimize sk_msg_clone(), from Vakul Garg.
7) Add SO_BINDTOIFINDEX, from David Herrmann.
8) Be more conservative with local resends due to local congestion,
from Yuchung Cheng.
9) Allow vetoing of unsupported VXLAN FDBs, from Petr Machata.
10) Add health buffer support to devlink, from Eran Ben Elisha.
11) Add TXQ scheduling API to mac80211, from Toke Høiland-Jørgensen.
12) Add statistics to basic packet scheduler filter, from Cong Wang.
13) Add GRE tunnel support for mlxsw Spectrum-2, from Nir Dotan.
14) Lots of new IP tunneling forwarding tests, also from Nir Dotan.
15) Add 3ad stats to bonding, from Nikolay Aleksandrov.
16) Lots of probing improvements for bpftool, from Quentin Monnet.
17) Various nfp drive #ebpf JIT improvements from Jakub Kicinski.
18) Allow #ebpf programs to access gso_segs from skb shared info, from
Eric Dumazet.
19) Add sock_diag support for AF_XDP sockets, from Björn Töpel.
20) Support 22260 iwlwifi devices, from Luca Coelho.
21) Use rbtree for ipv6 defragmentation, from Peter Oskolkov.
22) Add JMP32 instruction class support to #ebpf, from Jiong Wang.
23) Add spinlock support to #ebpf, from Alexei Starovoitov.
24) Support 256-bit keys and TLS 1.3 in ktls, from Dave Watson.
25) Add device infomation API to devlink, from Jakub Kicinski.
26) Add new timestamping socket options which are y2038 safe, from
Deepa Dinamani.
27) Add RX checksum offloading for various sh_eth chips, from Sergei
Shtylyov.
28) Flow offload infrastructure, from Pablo Neira Ayuso.
29) Numerous cleanups, improvements, and bug fixes to the PHY layer
and many drivers from Heiner Kallweit.
30) Lots of changes to try and make packet scheduler classifiers run
lockless as much as possible, from Vlad Buslov.
31) Support BCM957504 chip in bnxt_en driver, from Erik Burrows.
32) Add concurrency tests to tc-tests infrastructure, from Vlad
Buslov.
33) Add hwmon support to aquantia, from Heiner Kallweit.
34) Allow 64-bit values for SO_MAX_PACING_RATE, from Eric Dumazet.
And I would be remiss if I didn't thank the various major networking
subsystem maintainers for integrating much of this work before I even
saw it. Alexei Starovoitov, Daniel Borkmann, Pablo Neira Ayuso,
Johannes Berg, Kalle Valo, and many others. Thank you!"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2207 commits)
net/sched: avoid unused-label warning
net: ignore sysctl_devconf_inherit_init_net without SYSCTL
phy: mdio-mux: fix Kconfig dependencies
net: phy: use phy_modify_mmd_changed in genphy_c45_an_config_aneg
net: dsa: mv88e6xxx: add call to mv88e6xxx_ports_cmode_init to probe for new DSA framework
selftest/net: Remove duplicate header
sky2: Disable MSI on Dell Inspiron 1545 and Gateway P-79
net/mlx5e: Update tx reporter status in case channels were successfully opened
devlink: Add support for direct reporter health state update
devlink: Update reporter state to error even if recover aborted
sctp: call iov_iter_revert() after sending ABORT
team: Free BPF filter when unregistering netdev
ip6mr: Do not call __IP6_INC_STATS() from preemptible context
isdn: mISDN: Fix potential NULL pointer dereference of kzalloc
net: dsa: mv88e6xxx: support in-band signalling on SGMII ports with external PHYs
cxgb4/chtls: Prefix adapter flags with CXGB4
net-sysfs: Switch to bitmap_zalloc()
mellanox: Switch to bitmap_zalloc()
bpf: add test cases for non-pointer sanitiation logic
mlxsw: i2c: Extend initialization by querying resources data
...
|
|
Pull spi updates from Mark Brown:
"A fairly quiet release for SPI, the biggest thing is the conversion to
use GPIO descriptors which is now 90% done but still needs some
stragglers converting.
Summary:
- Support for inter-word delays
- Conversion of the core and most drivers to use GPIO descriptors for
GPIO controlled chip selects
- New drivers for NXP FlexSPI and QuadSPI, SiFive and Spreadtrum"
* tag 'spi-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (104 commits)
spi: sh-msiof: Restrict bits per word to 8/16/24/32 on R-Car Gen2/3
spi: sifive: Remove redundant dev_err call in sifive_spi_probe()
spi: sifive: Remove spi_master_put in sifive_spi_remove()
spi: spi-gpio: fix SPI_CS_HIGH capability
spi: pxa2xx: Setup maximum supported DMA transfer length
spi: sifive: Add driver for the SiFive SPI controller
spi: sifive: Add DT documentation for SiFive SPI controller
spi: sprd: Add a prefix for SPI DMA channel macros
spi: sprd: spi: sprd: Add DMA mode support
dt-bindings: spi: Add the DMA properties for the SPI dma mode
spi: sprd: Add the SPI irq function for the SPI DMA mode
dt-bindings: spi: imx: Add an entry for the i.MX8QM compatible
spi: use gpio[d]_set_value_cansleep for setting chipselect GPIO
spi: gpio: Advertise support for SPI_CS_HIGH
spi: sh-msiof: Replace spi_master by spi_controller
spi: sh-hspi: Replace spi_master by spi_controller
spi: rspi: Replace spi_master by spi_controller
spi: atmel-quadspi: add support for sam9x60 qspi controller
dt-bindings: spi: atmel-quadspi: QuadSPI driver for Microchip SAM9X60
spi: atmel-quadspi: add support for named peripheral clock
...
|
|
Pull regulator updates from Mark Brown:
"The bulk of the standout changes in this release are cleanups, with
the core work being a combination of factoring out common code into
helpers and the completion of the conversion of the core to use GPIO
descriptors.
Summary:
- Addition of helper functions for current limits and conversion of
drivers to use them by Axel Lin.
- Lots and lots of cleanups from Axel Lin.
- Conversion of the core to use GPIO descriptors rather than numbers
by Linus Walleij.
- New drivers for Maxim MAX77650 and ROHM BD70528"
* tag 'regulator-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (131 commits)
regulator: mc13xxx: Constify regulator_ops variables
regulator: palmas: Constify palmas_smps_ramp_delay array
regulator: wm831x-dcdc: Convert to use regulator_set/get_current_limit_regmap
regulator: pv88090: Convert to use regulator_set/get_current_limit_regmap
regulator: pv88080: Convert to use regulator_set/get_current_limit_regmap
regulator: pv88060: Convert to use regulator_set/get_current_limit_regmap
regulator: max77650: Convert to use regulator_set/get_current_limit_regmap
regulator: lp873x: Convert to use regulator_set/get_current_limit_regmap
regulator: lp872x: Convert to use regulator_set/get_current_limit_regmap
regulator: da9210: Convert to use regulator_set/get_current_limit_regmap
regulator: da9055: Convert to use regulator_set/get_current_limit_regmap
regulator: core: Add set/get_current_limit helpers for regmap users
regulator: Fix comment for csel_reg and csel_mask
regulator: stm32-vrefbuf: add power management support
regulator: 88pm8607: Remove unused fields from struct pm8607_regulator_info
regulator: 88pm8607: Simplify pm8607_list_voltage implementation
regulator: cpcap: Constify omap4_regulators and xoom_regulators
regulator: cpcap: Remove unused vsel_shift from struct cpcap_regulator
dt-bindings: regulator: tps65218: rectify units of LS3
dt-bindings: regulator: add LS2 load switch documentation
...
|
|
|
|
Every in-kernel use of this function defined it to KERNEL_DS (either as
an actual define, or as an inline function). It's an entirely
historical artifact, and long long long ago used to actually read the
segment selector valueof '%ds' on x86.
Which in the kernel is always KERNEL_DS.
Inspired by a patch from Jann Horn that just did this for a very small
subset of users (the ones in fs/), along with Al who suggested a script.
I then just took it to the logical extreme and removed all the remaining
gunk.
Roughly scripted with
git grep -l '(get_ds())' -- :^tools/ | xargs sed -i 's/(get_ds())/(KERNEL_DS)/'
git grep -lw 'get_ds' -- :^tools/ | xargs sed -i '/^#define get_ds()/d'
plus manual fixups to remove a few unusual usage patterns, the couple of
inline function cases and to fix up a comment that had become stale.
The 'get_ds()' function remains in an x86 kvm selftest, since in user
space it actually does something relevant.
Inspired-by: Jann Horn <jannh@google.com>
Inspired-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This adds a warning (once) for any kernel dereference that has a user
exception handler, but accesses a non-canonical address. It basically
is a simpler - and more limited - version of commit 9da3f2b74054
("x86/fault: BUG() when uaccess helpers fault on kernel addresses") that
got reverted.
Note that unlike that original commit, this only causes a warning,
because there are real situations where we currently can do this
(notably speculative argument fetching for uprobes etc). Also, unlike
that original commit, this _only_ triggers for #GP accesses, so the
cases of valid kernel pointers that cross into a non-mapped page aren't
affected.
The intent of this is two-fold:
- the uprobe/tracing accesses really do need to be more careful. In
particular, from a portability standpoint it's just wrong to think
that "a pointer is a pointer", and use the same logic for any random
pointer value you find on the stack. It may _work_ on x86-64, but it
doesn't necessarily work on other architectures (where the same
pointer value can be either a kernel pointer _or_ a user pointer, and
you really need to be much more careful in how you try to access it)
The warning can hopefully end up being a reminder that just any
random pointer access won't do.
- Kees in particular wanted a way to actually report invalid uses of
wild pointers to user space accessors, instead of just silently
failing them. Automated fuzzers want a way to get reports if the
kernel ever uses invalid values that the fuzzer fed it.
The non-canonical address range is a fair chunk of the address space,
and with this you can teach syzkaller to feed in invalid pointer
values and find cases where we do not properly validate user
addresses (possibly due to bad uses of "set_fs()").
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Jann Horn <jannh@google.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
|
|
Pull ARM SoC fixes from Arnd Bergmann:
"One more set of simple ARM platform fixes:
- A boot regression on qualcomm msm8998
- Gemini display controllers got turned off by accident
- incorrect reference counting in optee"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
tee: optee: add missing of_node_put after of_device_is_available
arm64: dts: qcom: msm8998: Extend TZ reserved memory area
ARM: dts: gemini: Re-enable display controller
|
|
Johan Hedberg says:
====================
pull request: bluetooth-next 2019-03-02
Here's one more bluetooth-next pull request for the 5.1 kernel:
- Added support for MediaTek MT7663U and MT7668U UART devices
- Cleanups & fixes to the hci_qca driver
- Fixed wakeup pin behavior for QCA6174A controller
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Pull x86 fixes from Thomas Gleixner:
"Two last minute fixes:
- Prevent value evaluation via functions happening in the user access
enabled region of __put_user() (put another way: make sure to
evaluate the value to be stored in user space _before_ enabling
user space accesses)
- Correct the definition of a Hyper-V hypercall constant"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/hyper-v: Fix definition of HV_MAX_FLUSH_REP_COUNT
x86/uaccess: Don't leak the AC flag into __put_user() value evaluation
|
|
Pull networking fixes from David Miller:
1) Fix refcount leak in act_ipt during replace, from Davide Caratti.
2) Set task state properly in tun during blocking reads, from Timur
Celik.
3) Leaked reference in DSA, from Wen Yang.
4) NULL deref in act_tunnel_key, from Vlad Buslov.
5) cipso_v4_erro can reference the skb IPCB in inappropriate contexts
thus referencing garbage, from Nazarov Sergey.
6) Don't accept RTA_VIA and RTA_GATEWAY in contexts where those
attributes make no sense.
7) Fix hung sendto in tipc, from Tung Nguyen.
8) Out-of-bounds access in netlabel, from Paul Moore.
9) Grant reference leak in xen-netback, from Igor Druzhinin.
10) Fix tx stalls with lan743x, from Bryan Whitehead.
11) Fix interrupt storm with mv88e6xxx, from Hein Kallweit.
12) Memory leak in sit on device registry failure, from Mao Wenan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
net: sit: fix memory leak in sit_init_net()
net: dsa: mv88e6xxx: Fix statistics on mv88e6161
geneve: correctly handle ipv6.disable module parameter
net: dsa: mv88e6xxx: prevent interrupt storm caused by mv88e6390x_port_set_cmode
bpf: fix sanitation rewrite in case of non-pointers
ipv4: Add ICMPv6 support when parse route ipproto
MIPS: eBPF: Fix icache flush end address
lan743x: Fix TX Stall Issue
net: phy: phylink: fix uninitialized variable in phylink_get_mac_state
net: aquantia: regression on cpus with high cores: set mode with 8 queues
selftests: fixes for UDP GRO
bpf: drop refcount if bpf_map_new_fd() fails in map_create()
net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390X
net: dsa: mv88e6xxx: Fix u64 statistics
xen-netback: don't populate the hash cache on XenBus disconnect
xen-netback: fix occasional leak of grant ref mappings under memory pressure
sctp: chunk.c: correct format string for size_t in printk
net: netem: fix skb length BUG_ON in __skb_to_sgvec
netlabel: fix out-of-bounds memory accesses
ipv4: Pass original device to ip_rcv_finish_core
...
|
|
Pull more crypto fixes from Herbert Xu:
"This fixes a couple of issues in arm64/chacha that was introduced in
5.0"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: arm64/chacha - fix hchacha_block_neon() for big endian
crypto: arm64/chacha - fix chacha_4block_xor_neon() for big endian
|
|
The MIPS eBPF JIT calls flush_icache_range() in order to ensure the
icache observes the code that we just wrote. Unfortunately it gets the
end address calculation wrong due to some bad pointer arithmetic.
The struct jit_ctx target field is of type pointer to u32, and as such
adding one to it will increment the address being pointed to by 4 bytes.
Therefore in order to find the address of the end of the code we simply
need to add the number of 4 byte instructions emitted, but we mistakenly
add the number of instructions multiplied by 4. This results in the call
to flush_icache_range() operating on a memory region 4x larger than
intended, which is always wasteful and can cause crashes if we overrun
into an unmapped page.
Fix this by correcting the pointer arithmetic to remove the bogus
multiplication, and use braces to remove the need for a set of brackets
whilst also making it obvious that the target field is a pointer.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: b6bd53f9c4e8 ("MIPS: Add missing file for eBPF JIT.")
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Yonghong Song <yhs@fb.com>
Cc: netdev@vger.kernel.org
Cc: bpf@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The LS1028A RDB board features an Atheros PHY connected over
SGMII to the ENETC PF0 (or Port0). ENETC Port1 (PF1) has no
external connection on this board, so it can be disabled for now.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The LS1028A SoC features a PCI Integrated Endpoint Root Complex
(IERC) defining several integrated PCI devices, including the ENETC
ethernet controller integrated endpoints (IEPs). The IERC implements
ECAM (Enhanced Configuration Access Mechanism) to provide access
to the PCIe config space of the IEPs. This means the the IEPs
(including ENETC) do not support the standard PCIe BARs, instead
the Enhanced Allocation (EA) capability structures in the ECAM space
are used to fix the base addresses in the system, and the PCI
subsystem uses these structures for device enumeration and discovery.
The "ranges" entries contain basic information from these EA capabily
structures required by the kernel for device enumeration.
The current patch also enables the first 2 ENETC PFs (Physiscal
Functions) and the associated VFs (Virtual Functions), 2 VFs for
each PF. Each of these ENETC PFs has an external ethernet port
on the LS1028A SoC.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The reset of the prefix to zero in swsusp_arch_resume uses a 4 byte stack
slot. With CONFIG_VMAP_STACK=y this is now in the vmalloc area, this works
only with DAT enabled. Move the DAT disable in swsusp_arch_resume after
the prefix reset.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Qualcomm ARM64 Fixes for 5.0-rc8
* Fix TZ memory area size to avoid crashes during boot
* tag 'qcom-fixes-for-5.0-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: dts: qcom: msm8998: Extend TZ reserved memory area
|
|
Add a warning about removing required architecture level set facilities
via "facilities=" command line option.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Add "facilities=" command line option which allows to override
facility bits returned by stfle. The main purpose of that is debugging
aids which allows to test specific kernel behaviour depending on
specific facilities presence. It also affects CPU alternatives.
"facilities=" command line option format is comma separated list of
integer values to be additionally set or cleared (if value is starting
with "!"). Values ranges are also supported. e.g.:
facilities=!130-160,159,167-169
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Facilities list in the lowcore is initially set up by verify_facilities
from als.c and later initializations are redundant, so cleaning them up.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Reuse __stfle call instead of in-place implementation. __stfle is using
memcpy and memset functions but they are safe to use, since mem.S is
built with -march=z900.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Pull MIPS fixes from Paul Burton:
"A few more MIPS fixes:
- Fix 16b cmpxchg() operations which could erroneously fail if bits
15:8 of the old value are non-zero. In practice I'm not aware of
any actual users of 16b cmpxchg() on MIPS, but this fixes the
support for it was was introduced in v4.13.
- Provide a struct device to dma_alloc_coherent for Lantiq XWAY
systems with a "Voice MIPS Macro Core" (VMMC) device.
- Provide DMA masks for BCM63xx ethernet devices, fixing a regression
introduced in v4.19.
- Fix memblock reservation for the kernel when the system has a
non-zero PHYS_OFFSET, correcting the memblock conversion performed
in v4.20"
* tag 'mips_fixes_5.0_4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: fix memory setup for platforms with PHYS_OFFSET != 0
MIPS: BCM63XX: provide DMA masks for ethernet devices
MIPS: lantiq: pass struct device to DMA API functions
MIPS: fix truncation in __cmpxchg_small for short values
|
|
Pull crypto fixes from Herbert Xu:
"This fixes a compiler warning introduced by a previous fix, as well as
two crash bugs on ARM"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: sha512/arm - fix crash bug in Thumb2 build
crypto: sha256/arm - fix crash bug in Thumb2 build
crypto: ccree - add missing inline qualifier
|
|
The max flush rep count of HvFlushGuestPhysicalAddressList hypercall is
equal with how many entries of union hv_gpa_page_range can be populated
into the input parameter page.
The code lacks parenthesis around PAGE_SIZE - 2 * sizeof(u64) which results
in bogus computations. Add them.
Fixes: cc4edae4b924 ("x86/hyper-v: Add HvFlushGuestAddressList hypercall support")
Signed-off-by: Lan Tianyu <Tianyu.Lan@microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: kys@microsoft.com
Cc: haiyangz@microsoft.com
Cc: sthemmin@microsoft.com
Cc: sashal@kernel.org
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: gregkh@linuxfoundation.org
Cc: devel@linuxdriverproject.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190225143114.5149-1-Tianyu.Lan@microsoft.com
|
|
On big endian arm64 kernels, the xchacha20-neon and xchacha12-neon
self-tests fail because hchacha_block_neon() outputs little endian words
but the C code expects native endianness. Fix it to output the words in
native endianness (which also makes it match the arm32 version).
Fixes: cc7cf991e9eb ("crypto: arm64/chacha20 - add XChaCha20 support")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The change to encrypt a fifth ChaCha block using scalar instructions
caused the chacha20-neon, xchacha20-neon, and xchacha12-neon self-tests
to start failing on big endian arm64 kernels. The bug is that the
keystream block produced in 32-bit scalar registers is directly XOR'd
with the data words, which are loaded and stored in native endianness.
Thus in big endian mode the data bytes end up XOR'd with the wrong
bytes. Fix it by byte-swapping the keystream words in big endian mode.
Fixes: 2fe55987b262 ("crypto: arm64/chacha - use combined SIMD/ALU routine for more speed")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
1-block SSE2 variant of poly1305 stores variables s1..s4 containing key
material on the stack. This commit adds missing zeroing of the stack
memory. Benchmarks show negligible performance hit (tested on i7-3770).
Signed-off-by: Tommi Hirvola <tommi@hirvola.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
For platforms, which use a PHYS_OFFSET != 0, symbol _end also
contains that offset. So when calling memblock_reserve() for
reserving kernel the size argument needs to be adjusted.
Fixes: bcec54bf3118 ("mips: switch to NO_BOOTMEM")
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # v4.20+
|
|
Currently, we don't coordinate BT USB activity with our handling of the
BT out-of-band wake pin, and instead just use gpio-keys. That causes
problems because we have no way of distinguishing wake activity due to a
BT device (e.g., mouse) vs. the BT controller (e.g., re-configuring wake
mask before suspend). This can cause spurious wake events just because
we, for instance, try to reconfigure the host controller's event mask
before suspending.
We can avoid these synchronization problems by handling the BT wake pin
directly in the btusb driver -- for all activity up until BT controller
suspend(), we simply listen to normal USB activity (e.g., to know the
difference between device and host activity); once we're really ready to
suspend the host controller, there should be no more host activity, and
only *then* do we unmask the GPIO interrupt.
This is already supported by btusb; we just need to describe the wake
pin in the right node.
We list 2 compatible properties, since both PID/VID pairs show up on
Scarlet devices, and they're both essentially identical QCA6174A-based
modules.
Also note that the polarity was wrong before: Qualcomm implemented WAKE
as active high, not active low. We only got away with this because
gpio-keys always reconfigured us as bi-directional edge-triggered.
Finally, we have an external pull-up and a level-shifter on this line
(we didn't notice Qualcomm's polarity in the initial design), so we
can't do pull-down. Switch to pull-none.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
My console locks up as soon as Linux writes to [88800000,88f00000[
AFAIU, that memory area is reserved for trustzone.
Extend TZ reserved memory range, to prevent Linux from stepping on
trustzone's toes.
Cc: stable@vger.kernel.org # 4.20+
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Fixes: c7833949564ec ("arm64: dts: qcom: msm8998: Add smem related nodes")
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
The separate GPHY Firmware loader driver is not used any more, the GPHY
firmware is now loaded by the GSWIP switch driver which also makes use
of the GPHY.
Remove the old unused GPHY firmware loader driver.
The GPHY firmware is useless without an Ethernet and switch driver, it
should not harm if loading this does not work for system using an old
device tree.
I am not aware of any vendor separating the device tree from the kernel
binary, it should be ok to remove this.
The code and the functionality form this separate GPHY firmware loader
was added to the gswip driver in commit 14fceff4771e ("net: dsa: Add
Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: john@phrozen.org
Cc: netdev@vger.kernel.org
|
|
The switch to the generic dma ops made dma masks mandatory, breaking
devices having them not set. In case of bcm63xx, it broke ethernet with
the following warning when trying to up the device:
[ 2.633123] ------------[ cut here ]------------
[ 2.637949] WARNING: CPU: 0 PID: 325 at ./include/linux/dma-mapping.h:516 bcm_enetsw_open+0x160/0xbbc
[ 2.647423] Modules linked in: gpio_button_hotplug
[ 2.652361] CPU: 0 PID: 325 Comm: ip Not tainted 4.19.16 #0
[ 2.658080] Stack : 80520000 804cd3ec 00000000 00000000 804ccc00 87085bdc 87d3f9d4 804f9a17
[ 2.666707] 8049cf18 00000145 80a942a0 00000204 80ac0000 10008400 87085b90 eb3d5ab7
[ 2.675325] 00000000 00000000 80ac0000 000022b0 00000000 00000000 00000007 00000000
[ 2.683954] 0000007a 80500000 0013b381 00000000 80000000 00000000 804a1664 80289878
[ 2.692572] 00000009 00000204 80ac0000 00000200 00000002 00000000 00000000 80a90000
[ 2.701191] ...
[ 2.703701] Call Trace:
[ 2.706244] [<8001f3c8>] show_stack+0x58/0x100
[ 2.710840] [<800336e4>] __warn+0xe4/0x118
[ 2.715049] [<800337d4>] warn_slowpath_null+0x48/0x64
[ 2.720237] [<80289878>] bcm_enetsw_open+0x160/0xbbc
[ 2.725347] [<802d1d4c>] __dev_open+0xf8/0x16c
[ 2.729913] [<802d20cc>] __dev_change_flags+0x100/0x1c4
[ 2.735290] [<802d21b8>] dev_change_flags+0x28/0x70
[ 2.740326] [<803539e0>] devinet_ioctl+0x310/0x7b0
[ 2.745250] [<80355fd8>] inet_ioctl+0x1f8/0x224
[ 2.749939] [<802af290>] sock_ioctl+0x30c/0x488
[ 2.754632] [<80112b34>] do_vfs_ioctl+0x740/0x7dc
[ 2.759459] [<80112c20>] ksys_ioctl+0x50/0x94
[ 2.763955] [<800240b8>] syscall_common+0x34/0x58
[ 2.768782] ---[ end trace fb1a6b14d74e28b6 ]---
[ 2.773544] bcm63xx_enetsw bcm63xx_enetsw.0: cannot allocate rx ring 512
Fix this by adding appropriate DMA masks for the platform devices.
Fixes: f8c55dc6e828 ("MIPS: use generic dma noncoherent ops for simple noncoherent platforms")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: stable@vger.kernel.org # v4.19+
|
|
When calling __put_user(foo(), ptr), the __put_user() macro would call
foo() in between __uaccess_begin() and __uaccess_end(). If that code
were buggy, then those bugs would be run without SMAP protection.
Fortunately, there seem to be few instances of the problem in the
kernel. Nevertheless, __put_user() should be fixed to avoid doing this.
Therefore, evaluate __put_user()'s argument before setting AC.
This issue was noticed when an objtool hack by Peter Zijlstra complained
about genregs_get() and I compared the assembly output to the C source.
[ bp: Massage commit message and fixed up whitespace. ]
Fixes: 11f1a4b9755f ("x86: reorganize SMAP handling in user space accesses")
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20190225125231.845656645@infradead.org
|
|
This reverts commit 9da3f2b74054406f87dff7101a569217ffceb29b.
It was well-intentioned, but wrong. Overriding the exception tables for
instructions for random reasons is just wrong, and that is what the new
code did.
It caused problems for tracing, and it caused problems for strncpy_from_user(),
because the new checks made perfectly valid use cases break, rather than
catch things that did bad things.
Unchecked user space accesses are a problem, but that's not a reason to
add invalid checks that then people have to work around with silly flags
(in this case, that 'kernel_uaccess_faults_ok' flag, which is just an
odd way to say "this commit was wrong" and was sprinked into random
places to hide the wrongness).
The real fix to unchecked user space accesses is to get rid of the
special "let's not check __get_user() and __put_user() at all" logic.
Make __{get|put}_user() be just aliases to the regular {get|put}_user()
functions, and make it impossible to access user space without having
the proper checks in places.
The raison d'être of the special double-underscore versions used to be
that the range check was expensive, and if you did multiple user
accesses, you'd do the range check up front (like the signal frame
handling code, for example). But SMAP (on x86) and PAN (on ARM) have
made that optimization pointless, because the _real_ expense is the "set
CPU flag to allow user space access".
Do let's not break the valid cases to catch invalid cases that shouldn't
even exist.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tobin C. Harding <tobin@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Jann Horn <jannh@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
commit 137cd7100ec6fa36d610e106df00acb4d8af99df
"ARM: dts: Enable Gemini flash access" contained a bug
by disabling the display controller, while the whole
idea with the patch was to enable flash access AND
the display controller, simultaneously. Fix it up.
Fixes: 137cd7100ec6 ("ARM: dts: Enable Gemini flash access")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull KVM fixes from Paolo Bonzini:
"Bug fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: MMU: record maximum physical address width in kvm_mmu_extended_role
kvm: x86: Return LA57 feature based on hardware capability
x86/kvm/mmu: fix switch between root and guest MMUs
s390: vsie: Use effective CRYCBD.31 to check CRYCBD validity
|
|
Pull powerpc fix from Michael Ellerman:
"One fix for an oops when using SRIOV, introduced by the recent changes
to support compound IOMMU groups.
Thanks to Alexey Kardashevskiy"
* tag 'powerpc-5.0-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powernv/sriov: Register IOMMU groups for VFs
|
|
Pull ARM SoC fixes from Arnd Bergmann:
"Only a handful of device tree fixes, all simple enough:
NVIDIA Tegra:
- Fix a regression for booting on chromebooks
TI OMAP:
- Two fixes PHY mode on am335x reference boards
Marvell mvebu:
- A regression fix for Armada XP NAND flash controllers
- An incorrect reset signal on the clearfog board"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: tegra: Restore DT ABI on Tegra124 Chromebooks
ARM: dts: am335x-evm: Fix PHY mode for ethernet
ARM: dts: am335x-evmsk: Fix PHY mode for ethernet
arm64: dts: clearfog-gt-8k: fix SGMII PHY reset signal
ARM: dts: armada-xp: fix Armada XP boards NAND description
|
|
Pull ARC fixes from Vineet Gupta:
"Fixes for ARC for 5.0, bunch of those are stable fodder anyways so
sooner the better.
- Fix memcpy to prevent prefetchw beyond end of buffer [Eugeniy]
- Enable unaligned access early to prevent exceptions given newer gcc
code gen [Eugeniy]
- Tighten up uboot arg checking to prevent false negatives and also
allow both jtag and bootloading to coexist w/o config option as
needed by kernelCi folks [Eugeniy]
- Set slab alignment to 8 for ARC to avoid the atomic64_t unalign
[Alexey]
- Disable regfile auto save on interrupts on HSDK platform due to a
silicon issue [Vineet]
- Avoid HS38x boot printing crash by not reading HS48x only reg
[Vineet]"
* tag 'arc-5.0-final' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARCv2: don't assume core 0x54 has dual issue
ARC: define ARCH_SLAB_MINALIGN = 8
ARC: enable uboot support unconditionally
ARC: U-boot: check arguments paranoidly
ARCv2: support manual regfile save on interrupts
ARC: uacces: remove lp_start, lp_end from clobber list
ARC: fix actionpoints configuration detection
ARCv2: lib: memcpy: fix doing prefetchw outside of buffer
ARCv2: Enable unaligned access in early ASM code
|
|
Pull parisc fixes from Helge Deller:
"Fix ptrace syscall number modification which has been broken since
kernel v4.5 and provide alternative email addresses for the remaining
users of the retired parisc-linux.org email domain"
* 'parisc-5.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
CREDITS/MAINTAINERS: Retire parisc-linux.org email domain
parisc: Fix ptrace syscall number modification
|
Linus Torvalds
Borislav Petkov
David S. Miller
Mark Brown
Paul Burton
Claudiu Manoil
Martin Schwidefsky
Arnd Bergmann
Vasily Gorbik
Lan Tianyu
Eric Biggers
Tommi Hirvola
Thomas Bogendoerfer
Brian Norris
Marc Gonzalez
Hauke Mehrtens
Jonas Gorski
Andy Lutomirski
Linus Walleij