| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This bug-fix makes sure that of_iomap is defined extern for sparc so that the
sparc-specific implementation of_iomap is once again used when including
include/linux/of_address.h in a sparc context. OF_GPIO that is now available for
sparc relies on this.
The bug was inadvertently introduced in a850a75, "of/address: add empty static
inlines for !CONFIG_OF", that added a static dummy inline for of_iomap when
!CONFIG_OF_ADDRESS. However, CONFIG_OF_ADDRESS is never defined for sparc, but
there is a sparc-specific implementation /arch/sparc/kernel/of_device_common.c.
This fix takes the same approach as 0bce04b that solved the equivalent problem
for of_address_to_resource.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
dev_pm_qos_add_request() can return 0, 1, or a negative error code,
therefore the correct error test is "if (error < 0)." Checking just for
non-zero return code leads to erroneous setting of the req->dev pointer
to NULL, which then leads to a repeated call to
dev_pm_qos_add_ancestor_request() in st1232_ts_irq_handler(). This in turn
leads to an Oops, when the I2C host adapter is unloaded and reloaded again
because of the inconsistent state of its QoS request list.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add information to the DMA Configuration Register to
maximize system performance:
- rx/tx packet buffer full memory size
- allow possibility to use INCR16 if supported
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Joachim Eastwood <manabian@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
this will allow to detect the link between the switch and the soc
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On BE2 chip, an interrupt being raised even when EQ is in un-armed state has
been observed a few times. This is not expected and has never been
observed on BE3/Lancer chips.
As a consequence, be_msix()::events_get() and be_poll()::events_get()
can race and notify an EQ wrongly causing a CEV UE. The other possible
side-effect would be traffic stalling because after notifying EQ,
napi_schedule() is ignored as NAPI is already running.
This patch fixes this issue by counting events only in be_poll().
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes tun_get_iff() prototype to return void as it never fails.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fix bug where a register which was only meant to be read in 578xx/57712
devices causes a bogus error message to be logged when read from other
devices.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch splits out the logic for entering suspend modes
to separate functions, to reduce the complexity of the
smsc95xx_suspend function.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables LAN9500 family devices to wake from suspend
on either link up or link down events
It also adds _nopm versions of mdio access functions, so we can
safely call them from suspend and resume functions
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of storing the number of wake-up frame filter registers
in the pdata structure, this patch changes the driver to detect
the type of device we have and store its available features.
The new two features will be used in future patches.
This patch is intended to have no change in behaviour.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
without this patch the two lines below won't ever execute
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function no longer exists.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some commands don't work in its example doc. The patch will fix it.
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch reverts b01af4579ec41f48e9b9c774e70bd6474ad210db.
The original patch was tested with emulated hardware. Real
hardware chokes.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=47041
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After we've done __elv_add_request() and __blk_run_queue() in
blk_execute_rq_nowait(), the request might finish and be freed
immediately. Therefore checking if the type is REQ_TYPE_PM_RESUME
isn't safe afterwards, because if it isn't, rq might be gone.
Instead, check beforehand and stash the result in a temporary.
This fixes crashes in blk_execute_rq_nowait() I get occasionally when
running with lots of memory debugging options enabled -- I think this
race is usually harmless because the window for rq to be reallocated
is so small.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Hi Jens,
Another tiny patch.
Removed __packed before the struct smart_attr and added __packed at end of
the structure to fix padding issue.
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Calling the request handler directly on a plugged queue defeats
the performance improvements provided by the plugging mechanism.
Use the __blk_run_queue function instead of calling the request
handler directly, so that we don't interfere with the block
layer's ability to plug the queue.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The dereference to port should be moved below the NULL test.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If we're building a 32-bit kernel and CONFIG_LBADF isn't set,
sector_t is 32-bits wide. The shifts by 32 and 40 are thus
larger than we support.
Cast the sector offset to a u64 to avoid these warnings.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Previous commit use value 3 for erasemode mask.
Changing the mask to correct value to 2
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Earlier lba address was assigned directly to lba_low and lba_low_ex,
which would result in a different number (bytes reversed) in
big-endian systems. Now assigning lba address byte-by-byte to fis.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The mtip driver lifted this code from elsewhere and then added a special
handling check for SEC_ERASE_UNIT. If the caller tries to do a security
erase but passes no output data for the command then outbuf is not
allocated and the driver duly explodes.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Request based dm attempts to re-run the request queue off the
request completion path. If used with a driver that potentially does
end_io from its request_fn, we could deadlock trying to recurse
back into request dispatch. Fix this by punting the request queue
run to kblockd.
Tested to fix a quickly reproducible deadlock in such a scenario.
Cc: stable@kernel.org
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We need to first destroy the floppy_wq workqueue before cleaning up
the queue. Otherwise we might race with still pending work with the
workqueue, but all the block queue already gone. This might lead to
various oopses, such as
CPU 0
Pid: 6, comm: kworker/u:0 Not tainted 3.7.0-rc4 #1 Bochs Bochs
RIP: 0010:[<ffffffff8134eef5>] [<ffffffff8134eef5>] blk_peek_request+0xd5/0x1c0
RSP: 0000:ffff88000dc7dd88 EFLAGS: 00010092
RAX: 0000000000000001 RBX: 0000000000000000 RCX: 0000000000000000
RDX: ffff88000f602688 RSI: ffffffff81fd95d8 RDI: 6b6b6b6b6b6b6b6b
RBP: ffff88000dc7dd98 R08: ffffffff81fd95c8 R09: 0000000000000000
R10: ffffffff81fd9480 R11: 0000000000000001 R12: 6b6b6b6b6b6b6b6b
R13: ffff88000dc7dfd8 R14: ffff88000dc7dfd8 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffffffff81e21000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000000 CR3: 0000000001e11000 CR4: 00000000000006f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process kworker/u:0 (pid: 6, threadinfo ffff88000dc7c000, task ffff88000dc5ecc0)
Stack:
0000000000000000 0000000000000000 ffff88000dc7ddb8 ffffffff8134efee
ffff88000dc7ddb8 0000000000000000 ffff88000dc7dde8 ffffffff814aef3c
ffffffff81e75d80 ffff88000dc0c640 ffff88000fbfb000 ffffffff814aed90
Call Trace:
[<ffffffff8134efee>] blk_fetch_request+0xe/0x30
[<ffffffff814aef3c>] redo_fd_request+0x1ac/0x400
[<ffffffff814aed90>] ? start_motor+0x130/0x130
[<ffffffff8106b526>] process_one_work+0x136/0x450
[<ffffffff8106af65>] ? manage_workers+0x205/0x2e0
[<ffffffff8106bb6d>] worker_thread+0x14d/0x420
[<ffffffff8106ba20>] ? rescuer_thread+0x1a0/0x1a0
[<ffffffff8107075a>] kthread+0xba/0xc0
[<ffffffff810706a0>] ? __kthread_parkme+0x80/0x80
[<ffffffff818b553a>] ret_from_fork+0x7a/0xb0
[<ffffffff810706a0>] ? __kthread_parkme+0x80/0x80
Code: 0f 84 c0 00 00 00 83 f8 01 0f 85 e2 00 00 00 81 4b 40 00 00 80 00 48 89 df e8 58 f8 ff ff be fb ff ff ff
fe ff ff <49> 8b 1c 24 49 39 dc 0f 85 2e ff ff ff 41 0f b6 84 24 28 04 00
RIP [<ffffffff8134eef5>] blk_peek_request+0xd5/0x1c0
RSP <ffff88000dc7dd88>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Currently, mac80211 checks the DS params IE if present and
uses it for the (primary) BSS channel, instead of the one
that the frame was received on. This is particularly useful
in the 2.4 GHz band since a frame is often received on one
of the adjacent channels due to overlap.
Move this code to cfg80211 so other drivers also do this.
Additionally, on 5 GHz, in particular with some (possibly)
upcoming changes in 802.11ai and duplicate transmissions
when wider channels are used, something similar happens.
So if present, also use the (primary) channel information
contained in the HT operation IE.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If the AP doesn't support HT, or more importantly if
it does but we have to disable it because its IEs are
broken, don't advertise HT support in our association
request. Otherwise, we configure our channel to be a
20 MHz non-HT channel but the AP might still think we
support HT, or even 40 MHz.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since the 11n spec amendment was rolled into the
2012 version, "11n" no longer makes sense. Use
"HT" instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If the driver doesn't support 40 MHz channels, then
mac80211 erroneously sets number of RX chains to one
although the number of chains is independent of the
support for 40 MHz channels.
Fix this by checking the 40 MHz support only for the
code that sets the 40 MHz channel not the complete
HT code block.
This also means the HT20 channel type will always be
set in the changed code block so there's no need to
set it in case we override the AP due to invalid IEs
in the probe response/beacon.
The indentation is a bit quirky, but I'm rewriting
this code for VHT support so this will change again
very soon.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The radiotap vendor area in the skb head must be skipped
and accounted for in a few functions until it is removed.
I missed this in my patch, so a few places use this data
as though it was the 802.11 header, fix these places.
Reported-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Tested-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Properly terminate the DMA transfer in case the DMA PIO transfer
or setup fails for any reason.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
Starting from 3.6 we cache output routes for
multicasts only when using route to 224/4. For local receivers
we can set RTCF_LOCAL flag depending on the membership but
in such case we use maddr and saddr which are not caching
keys as before. Additionally, we can not use same place to
cache routes that differ in RTCF_LOCAL flag value.
Fix it by caching only RTCF_MULTICAST entries
without RTCF_LOCAL (send-only, no loopback). As a side effect,
we avoid unneeded lookup for fnhe when not caching because
multicasts are not redirected and they do not learn PMTU.
Thanks to Maxime Bizon for showing the caching
problems in __mkroute_output for 3.6 kernels: different
RTCF_LOCAL flag in cache can lead to wrong ip_mc_output or
ip_output call and the visible problem is that traffic can
not reach local receivers via loopback.
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Tested-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is work the same as for ipv4.
All other hacks about tcp repair are in common code for ipv4 and ipv6,
so this patch is enough for repairing ipv6 connections.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jeffrey Barish reported an obvious bug in the pcm part of the usb-audio
driver which causes the code to not initialize the sync endpoint from
configure_endpoint().
Reported-by: Jeffrey Barish <jeff_barish@earthlink.net>
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: stable@kernel.org [3.5+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
There used to be a time when TIPC had lots of Kconfig knobs the
end user could alter, but they have all been made automatic or
obsolete, with the exception of CONFIG_TIPC_PORTS. This
previously existing set of options was all hidden under the
TIPC_ADVANCED setting, which does not exist in any code, but
only in Kconfig scope.
Having this now, just to hide the one remaining "advanced"
option no longer makes sense. Remove it. Also get rid of the
ifdeffery in the TIPC code that allowed for TIPC_PORTS to be
possibly undefined.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
As the variable:node is currently defined to u32 type, it is
unnecessary to cast its type to u32 again when using it.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Upon establishing a first link between two nodes, there is
currently a risk that the two endpoints will disagree on exactly
which sequence number reception and acknowleding of broadcast
packets should start.
The following scenarios may happen:
1: Node A sends an ACTIVATE message to B, telling it to start acking
packets from sequence number N.
2: Node A sends out broadcast N, but does not expect an acknowledge
from B, since B is not yet in its broadcast receiver's list.
3: Node A receives ACK for N from all nodes except B, and releases
packet N.
4: Node B receives the ACTIVATE, activates its link endpoint, and
stores the value N as sequence number of first expected packet.
5: Node B sends a NAME_DISTR message to A.
6: Node A receives the NAME_DISTR message, and activates its endpoint.
At this moment B is added to A's broadcast receiver's set.
Node A also sets sequence number 0 as the first broadcast packet
to be received from B.
7: Node A sends broadcast N+1.
8: B receives N+1, determines there is a gap in the sequence, since
it is expecting N, and sends a NACK for N back to A.
9: Node A has already released N, so no retransmission is possible.
The broadcast link in direction A->B is stale.
In addition to, or instead of, 7-9 above, the following may happen:
10: Node B sends broadcast M > 0 to A.
11: Node A receives M, falsely decides there must be a gap, since
it is expecting packet 0, and asks for retransmission of packets
[0,M-1].
12: Node B has already released these packets, so the broadcast
link is stale in direction B->A.
We solve this problem by introducing a new unicast message type,
BCAST_PROTOCOL/STATE, to convey the sequence number of the next
sent broadcast packet to the other endpoint, at exactly the moment
that endpoint is added to the own node's broadcast receivers list,
and before any other unicast messages are permitted to be sent.
Furthermore, we don't allow any node to start receiving and
processing broadcast packets until this new synchronization
message has been received.
To maintain backwards compatibility, we still open up for
broadcast reception if we receive a NAME_DISTR message without
any preceding broadcast sync message. In this case, we must
assume that the other end has an older code version, and will
never send out the new synchronization message. Hence, for mixed
old and new nodes, the issue arising in 7-12 of the above may
happen with the same probability as before.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Do not fail if dpll4_m4_ck is missing. The clock is not there on omap24xx,
so this should not be a hard error.
The patch retains the functionality before the commit 185bae10 (OMAPDSS:
DSS: Cleanup cpu_is_xxxx checks).
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Rename the "supported" flag in bclink structure to "recv_permitted"
to better reflect what it is used for. When this flag is set for a
given node, we are permitted to receive and acknowledge broadcast
messages from that node. Convert it to a bool at the same time,
since it is not used to store any numerical values.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
The "supportable" flag in bclink structure is a compatibility flag
indicating whether a peer node is capable of receiving TIPC broadcast
messages. However, all TIPC versions since tipc-1.5, and after the
inclusion in the upstream Linux kernel in 2006, support this capability.
It is highly unlikely that anybody is still using such an old
version of TIPC, let alone that they want to mix it with TIPC-2.0
nodes. Therefore, we now remove the "supportable" flag.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
This change makes it so that only the first fragment in a series of fragments
will have the L4 header pulled. Previously we were always pulling the L4
header as well and in the case of UDP this can harm performance since only the
first fragment will have the header, the rest just contain data which should
be left in the paged portion of the packet.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Historically, we've been using the APME bit to determine whether a device
supports wake on a given port or not. However, this bit specifies the
default wake setting, rather than the wake support. Change the behavior so
that we use a flag to keep the capabilities separate from the enablement
while meeting customer requirements.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Update the filters to be more consistent with what the driver wants to do.
For example, for devices that timestamp all packets, report that the filter
is set for timestamping all packets.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There was a bitwise operation error in the fdb_add block
that was only allowing FDB types that were not permanent.
This was the opposite of the intent because the hardware
never ages out address these are the _only_ type of addrs
that should be allowed.
This was missed because until recently iproute2 did not
set any bit for this by default. And our test code to
manage FDB entries on embedded devices similarly did not
set these bits.
I am going to chalk this up as a bug and fix it now.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch enables ethtool to correctly identify flow control (pause
frame) auto negotiation, as well as disallow enabling it when it is not
supported. The ixgbe_device_supports_autoneg_fc function is exported and
used for this purpose.
There is also one minor cleanup of the device_supports_autoneg_fc by
removing an unnecessary return statement.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch removes the queuing that was previously done for L4 packets
as it is not needed. The filter does not provide functionality, and it
is possible that queue setup here could trample settings done else-where
in the driver. (for example it may use a queue which isn't setup.)
Setting of the queue is not required for hardware timestamping and could
have inadverdent side effects.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch removes a magic number that was used for the ETQF used for
filtering L2 ptp packets and replaces it with the supplied define that
previously existed. The intent is to clarify that this filter is already
set aside for L2 1588 work.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This removes an open coded simple_open() function and
replaces file operations references to the function
with simple_open() instead.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Reformats the output of the Tx/Rx descriptor dumps to more
appropriately align the output of the ixgbe_dump and improve readability.
Prevents empty Tx descriptors from being displayed to decrease the size
of the dump and make it more manageable.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
int sys32_rt_sigprocmask(int how, compat_sigset_t __user *set, compat_sigset_t __user *oset,
unsigned int sigsetsize)
{
sigset_t old_set, new_set;
int ret;
if (set && get_sigset32(set, &new_set, sigsetsize))
...
static int
get_sigset32(compat_sigset_t __user *up, sigset_t *set, size_t sz)
{
compat_sigset_t s;
int r;
if (sz != sizeof *set) panic("put_sigset32()");
In other words, rt_sigprocmask(69, (void *)69, 69) done by 32bit process
will promptly panic the box.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
Andreas Larsson
Guennadi Liakhovetski
Nicolas Ferre
Jean-Christophe PLAGNIOL-VILLARD
Sathya Perla
Rami Rosen
Ariel Elior
Steve Glendinning
Neal Cardwell
Zhi Yong Wu
françois romieu
Roland Dreier
Selvan Mani
Ed Cashin
Wei Yongjun
Jens Axboe
Jiri Kosina
Johannes Berg
Marek Vasut
Julian Anastasov
Andrey Vagin
Daniel Mack
Paul Gortmaker
Ying Xue
Jon Maloy
Aaro Koskinen
Alexander Duyck
Matthew Vick
John Fastabend
Jacob Keller
Josh Hay
Al Viro