| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Summary:
This appears to be necessary and sufficient change to enable `MPLS` on
`ip6gre` tunnels (RFC4023).
This diff allows IP6GRE devices to be recognized by MPLS kernel module
and hence user can configure interface to accept packets with mpls
headers as well setup mpls routes on them.
Test Plan:
Test plan consists of multiple containers connected via GRE-V6 tunnel.
Then carrying out testing steps as below.
- Carry out necessary sysctl settings on all containers
```
sysctl -w net.mpls.platform_labels=65536
sysctl -w net.mpls.ip_ttl_propagate=1
sysctl -w net.mpls.conf.lo.input=1
```
- Establish IP6GRE tunnels
```
ip -6 tunnel add name if_1_2_1 mode ip6gre \
local 2401:db00:21:6048:feed:0::1 \
remote 2401:db00:21:6048:feed:0::2 key 1
ip link set dev if_1_2_1 up
sysctl -w net.mpls.conf.if_1_2_1.input=1
ip -4 addr add 169.254.0.2/31 dev if_1_2_1 scope link
ip -6 tunnel add name if_1_3_1 mode ip6gre \
local 2401:db00:21:6048:feed:0::1 \
remote 2401:db00:21:6048:feed:0::3 key 1
ip link set dev if_1_3_1 up
sysctl -w net.mpls.conf.if_1_3_1.input=1
ip -4 addr add 169.254.0.4/31 dev if_1_3_1 scope link
```
- Install MPLS encap rules on node-1 towards node-2
```
ip route add 192.168.0.11/32 nexthop encap mpls 32/64 \
via inet 169.254.0.3 dev if_1_2_1
```
- Install MPLS forwarding rules on node-2 and node-3
```
// node2
ip -f mpls route add 32 via inet 169.254.0.7 dev if_2_4_1
// node3
ip -f mpls route add 64 via inet 169.254.0.12 dev if_4_3_1
```
- Ping 192.168.0.11 (node4) from 192.168.0.1 (node1) (where routing
towards 192.168.0.1 is via IP route directly towards node1 from node4)
```
ping 192.168.0.11
```
- tcpdump on interface to capture ping packets wrapped within MPLS
header which inturn wrapped within IP6GRE header
```
16:43:41.121073 IP6
2401:db00:21:6048:feed::1 > 2401:db00:21:6048:feed::2:
DSTOPT GREv0, key=0x1, length 100:
MPLS (label 32, exp 0, ttl 255) (label 64, exp 0, [S], ttl 255)
IP 192.168.0.1 > 192.168.0.11:
ICMP echo request, id 1208, seq 45, length 64
0x0000: 6000 2cdb 006c 3c3f 2401 db00 0021 6048 `.,..l<?$....!`H
0x0010: feed 0000 0000 0001 2401 db00 0021 6048 ........$....!`H
0x0020: feed 0000 0000 0002 2f00 0401 0401 0100 ......../.......
0x0030: 2000 8847 0000 0001 0002 00ff 0004 01ff ...G............
0x0040: 4500 0054 3280 4000 ff01 c7cb c0a8 0001 E..T2.@.........
0x0050: c0a8 000b 0800 a8d7 04b8 002d 2d3c a05b ...........--<.[
0x0060: 0000 0000 bcd8 0100 0000 0000 1011 1213 ................
0x0070: 1415 1617 1819 1a1b 1c1d 1e1f 2021 2223 .............!"#
0x0080: 2425 2627 2829 2a2b 2c2d 2e2f 3031 3233 $%&'()*+,-./0123
0x0090: 3435 3637 4567
```
Signed-off-by: Saif Hasan <has@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes skb_shared area, which will be corrupted
upon reception of 4K jumbo packets.
Originally build_skb usage purpose was to reuse page for skb to eliminate
needs of extra fragments. But that logic does not take into account that
skb_shared_info should be reserved at the end of skb data area.
In case packet data consumes all the page (4K), skb_shinfo location
overflows the page. As a consequence, __build_skb zeroed shinfo data above
the allocated page, corrupting next page.
The issue is rarely seen in real life because jumbo are normally larger
than 4K and that causes another code path to trigger.
But it 100% reproducible with simple scapy packet, like:
sendp(IP(dst="192.168.100.3") / TCP(dport=443) \
/ Raw(RandString(size=(4096-40))), iface="enp1s0")
Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code")
Reported-by: Friedemann Gerold <f.gerold@b-c-s.de>
Reported-by: Michael Rauch <michael@rauch.be>
Signed-off-by: Friedemann Gerold <f.gerold@b-c-s.de>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
tun uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
nfp uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Tested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
bnxt uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
bnx2x uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
mlx5 uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
mlx4 uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
i40evf uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ice uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
igb uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ixgb uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
This also removes a problematic use of disable_irq() in
a context it is forbidden, as explained in commit
af3e0fcf7887 ("8139too: Use disable_irq_nosync() in
rtl8139_poll_controller()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
lasts for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
fm10k uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ixgbevf uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ixgbe uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Reported-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Song Liu <songliubraving@fb.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We want to allow NAPI drivers to no longer provide
ndo_poll_controller() method, as it has been proven problematic.
team driver must not look at its presence, but instead call
netpoll_poll_dev() which factorize the needed actions.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
It seems that all networking drivers that do use NAPI
for their TX completions, should not provide a ndo_poll_controller().
NAPI drivers have netpoll support already handled
in core networking stack, since netpoll_poll_dev()
uses poll_napi(dev) to iterate through registered
NAPI contexts for a device.
This patch allows netpoll_poll_dev() to process NAPI
contexts even for drivers not providing ndo_poll_controller(),
allowing for following patches in NAPI drivers.
Also we export netpoll_poll_dev() so that it can be called
by bonding/team drivers in following patches.
Reported-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Song Liu <songliubraving@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use DECLARE_* not DEFINE_*
Fixes: 8360ed6745df ("RDS: IB: Use DEFINE_PER_CPU_SHARED_ALIGNED for rds_ib_stats")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So it should not fail with EPERM even though it is no longer implemented...
This is a fix for:
(userns)$ egrep ^Cap /proc/self/status
CapInh: 0000003fffffffff
CapPrm: 0000003fffffffff
CapEff: 0000003fffffffff
CapBnd: 0000003fffffffff
CapAmb: 0000003fffffffff
(userns)$ tcpdump -i usb_rndis0
tcpdump: WARNING: usb_rndis0: SIOCETHTOOL(ETHTOOL_GUFO) ioctl failed: Operation not permitted
Warning: Kernel filter failed: Bad file descriptor
tcpdump: can't remove kernel filter: Bad file descriptor
With this change it returns EOPNOTSUPP instead of EPERM.
See also https://github.com/the-tcpdump-group/libpcap/issues/689
Fixes: 08a00fea6de2 "net: Remove references to NETIF_F_UFO from ethtool."
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clang warns when two declarations' section attributes don't match.
net/rds/ib_stats.c:40:1: warning: section does not match previous
declaration [-Wsection]
DEFINE_PER_CPU_SHARED_ALIGNED(struct rds_ib_statistics, rds_ib_stats);
^
./include/linux/percpu-defs.h:142:2: note: expanded from macro
'DEFINE_PER_CPU_SHARED_ALIGNED'
DEFINE_PER_CPU_SECTION(type, name,
PER_CPU_SHARED_ALIGNED_SECTION) \
^
./include/linux/percpu-defs.h:93:9: note: expanded from macro
'DEFINE_PER_CPU_SECTION'
extern __PCPU_ATTRS(sec) __typeof__(type) name;
\
^
./include/linux/percpu-defs.h:49:26: note: expanded from macro
'__PCPU_ATTRS'
__percpu __attribute__((section(PER_CPU_BASE_SECTION sec)))
\
^
net/rds/ib.h:446:1: note: previous attribute is here
DECLARE_PER_CPU(struct rds_ib_statistics, rds_ib_stats);
^
./include/linux/percpu-defs.h:111:2: note: expanded from macro
'DECLARE_PER_CPU'
DECLARE_PER_CPU_SECTION(type, name, "")
^
./include/linux/percpu-defs.h:87:9: note: expanded from macro
'DECLARE_PER_CPU_SECTION'
extern __PCPU_ATTRS(sec) __typeof__(type) name
^
./include/linux/percpu-defs.h:49:26: note: expanded from macro
'__PCPU_ATTRS'
__percpu __attribute__((section(PER_CPU_BASE_SECTION sec)))
\
^
1 warning generated.
The initial definition was added in commit ec16227e1414 ("RDS/IB:
Infiniband transport") and the cache aligned definition was added in
commit e6babe4cc4ce ("RDS/IB: Stats and sysctls") right after. The
definition probably should have been updated in net/rds/ib.h, which is
what this patch does.
Link: https://github.com/ClangBuiltLinux/linux/issues/114
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clang warns that the address of a pointer will always evaluated as true
in a boolean context:
drivers/net/ethernet/mellanox/mlx4/eq.c:243:11: warning: address of
array 'eq->affinity_mask' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (!eq->affinity_mask || cpumask_empty(eq->affinity_mask))
~~~~~^~~~~~~~~~~~~
1 warning generated.
Use cpumask_available, introduced in commit f7e30f01a9e2 ("cpumask: Add
helper cpumask_available()"), which does the proper checking and avoids
this warning.
Link: https://github.com/ClangBuiltLinux/linux/issues/86
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Smatch reports that devlink_dpipe_send_and_alloc_skb() frees the skb
on error so this is a double free. We fixed a bunch of these bugs in
commit 7fe4d6dcbcb4 ("devlink: Remove redundant free on error path") but
we accidentally overlooked this one.
Fixes: d9f9b9a4d05f ("devlink: Add support for resource abstraction")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of error, the function pci_create_slot() returns ERR_PTR() and
never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR().
Fixes: a15f2c08c708 ("PCI: hv: support reporting serial number as slot information")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The backend handling for /proc/net/if_inet6 in addrconf.c doesn't properly
handle starting/stopping the iteration. The problem is that at some point
during the iteration, an overflow is detected and the process is
subsequently stopped. The item being shown via seq_printf() when the
overflow occurs is not actually shown, though. When start() is
subsequently called to resume iterating, it returns the next item, and
thus the item that was being processed when the overflow occurred never
gets printed.
Alter the meaning of the private data member "offset". Currently, when it
is not 0 (which only happens at the very beginning), "offset" represents
the next hlist item to be printed. After this change, "offset" always
represents the current item.
This is also consistent with the private data member "bucket", which
represents the current bucket, and also the use of "pos" as defined in
seq_file.txt:
The pos passed to start() will always be either zero, or the most
recent pos used in the previous session.
Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netlbl_unlabel_addrinfo_get() assumes that if it finds the
NLBL_UNLABEL_A_IPV4ADDR attribute, it must also have the
NLBL_UNLABEL_A_IPV4MASK attribute as well. However, this is
not necessarily the case as the current checks in
netlbl_unlabel_staticadd() and friends are not sufficent to
enforce this.
If passed a netlink message with NLBL_UNLABEL_A_IPV4ADDR,
NLBL_UNLABEL_A_IPV6ADDR, and NLBL_UNLABEL_A_IPV6MASK attributes,
these functions will all call netlbl_unlabel_addrinfo_get() which
will then attempt dereference NULL when fetching the non-existent
NLBL_UNLABEL_A_IPV4MASK attribute:
Unable to handle kernel NULL pointer dereference at virtual address 0
Process unlab (pid: 31762, stack limit = 0xffffff80502d8000)
Call trace:
netlbl_unlabel_addrinfo_get+0x44/0xd8
netlbl_unlabel_staticremovedef+0x98/0xe0
genl_rcv_msg+0x354/0x388
netlink_rcv_skb+0xac/0x118
genl_rcv+0x34/0x48
netlink_unicast+0x158/0x1f0
netlink_sendmsg+0x32c/0x338
sock_sendmsg+0x44/0x60
___sys_sendmsg+0x1d0/0x2a8
__sys_sendmsg+0x64/0xb4
SyS_sendmsg+0x34/0x4c
el0_svc_naked+0x34/0x38
Code: 51001149 7100113f 540000a0 f9401508 (79400108)
---[ end trace f6438a488e737143 ]---
Kernel panic - not syncing: Fatal exception
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ensure that sockets added to a sock{map|hash} that is not in the
ESTABLISHED state is rejected.
Fixes: 1aa12bdf1bfb ("bpf: sockmap, add sock close() hook to remove socks")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
It is possible (via shutdown()) for TCP socks to go trough TCP_CLOSE
state via tcp_disconnect() without actually calling tcp_close which
would then call our bpf_tcp_close() callback. Because of this a user
could disconnect a socket then put it in a LISTEN state which would
break our assumptions about sockets always being ESTABLISHED state.
To resolve this rely on the unhash hook, which is called in the
disconnect case, to remove the sock from the sockmap.
Reported-by: Eric Dumazet <edumazet@google.com>
Fixes: 1aa12bdf1bfb ("bpf: sockmap, add sock close() hook to remove socks")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
After this patch we only allow socks that are in ESTABLISHED state or
are being added via a sock_ops event that is transitioning into an
ESTABLISHED state. By allowing sock_ops events we allow users to
manage sockmaps directly from sock ops programs. The two supported
sock_ops ops are BPF_SOCK_OPS_PASSIVE_ESTABLISHED_CB and
BPF_SOCK_OPS_ACTIVE_ESTABLISHED_CB.
Similar to TLS ULP this ensures sk_user_data is correct.
Reported-by: Eric Dumazet <edumazet@google.com>
Fixes: 1aa12bdf1bfb ("bpf: sockmap, add sock close() hook to remove socks")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
When extracting frames from the Ocelot switch, the frame check sequence
(FCS) is present at the end of the data extracted. The FCS was put into
the sk buffer which introduced some issues (as length related ones), as
the FCS shouldn't be part of an Rx sk buffer.
This patch fixes the Ocelot switch extraction behaviour by discarding
the FCS.
Fixes: a556c76adc05 ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was reported that chip version 33 (RTL8168E) ends up with
10MBit/Half on a 1GBit link after resuming from S3 (with different
link partners). For whatever reason the PHY on this chip doesn't
properly start a renegotiation when soft-reset.
Explicitly requesting a renegotiation fixes this.
Fixes: a2965f12fde6 ("r8169: remove rtl8169_set_speed_xmii")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: Neil MacLeod <neil@nmacleod.com>
Tested-by: Neil MacLeod <neil@nmacleod.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When processing pmtu update from an icmp packet, it calls .update_pmtu
with sk instead of skb in sctp_transport_update_pmtu.
However for sctp, the daddr in the transport might be different from
inet_sock->inet_daddr or sk->sk_v6_daddr, which is used to update or
create the route cache. The incorrect daddr will cause a different
route cache created for the path.
So before calling .update_pmtu, inet_sock->inet_daddr/sk->sk_v6_daddr
should be updated with the daddr in the transport, and update it back
after it's done.
The issue has existed since route exceptions introduction.
Fixes: 4895c771c7f0 ("ipv4: Add FIB nexthop exceptions.")
Reported-by: ian.periam@dialogic.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnxt offload code currently supports only 'push' and 'pop' operation: let
.ndo_setup_tc() return -EOPNOTSUPP if VLAN 'modify' action is configured.
Fixes: 2ae7408fedfe ("bnxt_en: bnxt: add TC flower filter offload support")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The generic netlink family is only initialized during module init,
so it should be __ro_after_init like all other generic netlink
families.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MC-aware mode was introduced to mlxsw in commit 7b8195306694 ("mlxsw: spectrum:
Configure MC-aware mode on mlxsw ports") and fixed up later in commit
3a3539cd3632 ("mlxsw: spectrum_buffers: Set up a dedicated pool for BUM
traffic"). As the final piece of puzzle, a firmware issue whereby a wrong
priority was assigned to BUM traffic was corrected in FW version 13.1703.4.
Therefore require this FW version in the driver.
Fixes: 7b8195306694 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support to configure the DORQ to use vlan-id/priority for
roce EDPM.
Fixes: cac6f691 ("qed: Add support for Unified Fabric Port")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In certain multi-function switch dependent modes, firmware adds vlan tag 0
to the untagged frames. This leads to double tagging for the traffic
if the dcbx is enabled, which is not the desired behavior. To avoid this,
driver needs to set "dcb_dont_add_vlan0" flag.
Fixes: cac6f691 ("qed: Add support for Unified Fabric Port")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In multi-function mode, driver receives the stag value (outer vlan)
for a PF from management FW (MFW). If the stag value is negotiated prior to
the driver load, then the stag is not notified to the driver and hence
driver will have the invalid stag value.
The fix is to request the MFW for STAG value during the driver load time.
Fixes: cac6f691 ("qed: Add support for Unified Fabric Port")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With CONFIG_DMA_API_DEBUG enabled we now get a warning when using the
mvneta driver:
mvneta d0030000.ethernet: DMA-API: device driver frees DMA memory with
wrong function [device address=0x000000001165b000] [size=4096 bytes]
[mapped as page] [unmapped as single]
This is because when using the s/w buffer management, the Rx descriptor
buffer is mapped with dma_map_page but unmapped with dma_unmap_single.
This patch fixes this by using the right unmapping function.
Fixes: 562e2f467e71 ("net: mvneta: Improve the buffer allocation method for SWBM")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
the ip6 tunnel xmit ndo assumes that the processed skb always
contains an ip[v6] header, but syzbot has found a way to send
frames that fall short of this assumption, leading to the following splat:
BUG: KMSAN: uninit-value in ip6ip6_tnl_xmit net/ipv6/ip6_tunnel.c:1307
[inline]
BUG: KMSAN: uninit-value in ip6_tnl_start_xmit+0x7d2/0x1ef0
net/ipv6/ip6_tunnel.c:1390
CPU: 0 PID: 4504 Comm: syz-executor558 Not tainted 4.16.0+ #87
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0x185/0x1d0 lib/dump_stack.c:53
kmsan_report+0x142/0x240 mm/kmsan/kmsan.c:1067
__msan_warning_32+0x6c/0xb0 mm/kmsan/kmsan_instr.c:683
ip6ip6_tnl_xmit net/ipv6/ip6_tunnel.c:1307 [inline]
ip6_tnl_start_xmit+0x7d2/0x1ef0 net/ipv6/ip6_tunnel.c:1390
__netdev_start_xmit include/linux/netdevice.h:4066 [inline]
netdev_start_xmit include/linux/netdevice.h:4075 [inline]
xmit_one net/core/dev.c:3026 [inline]
dev_hard_start_xmit+0x5f1/0xc70 net/core/dev.c:3042
__dev_queue_xmit+0x27ee/0x3520 net/core/dev.c:3557
dev_queue_xmit+0x4b/0x60 net/core/dev.c:3590
packet_snd net/packet/af_packet.c:2944 [inline]
packet_sendmsg+0x7c70/0x8a30 net/packet/af_packet.c:2969
sock_sendmsg_nosec net/socket.c:630 [inline]
sock_sendmsg net/socket.c:640 [inline]
___sys_sendmsg+0xec0/0x1310 net/socket.c:2046
__sys_sendmmsg+0x42d/0x800 net/socket.c:2136
SYSC_sendmmsg+0xc4/0x110 net/socket.c:2167
SyS_sendmmsg+0x63/0x90 net/socket.c:2162
do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
RIP: 0033:0x441819
RSP: 002b:00007ffe58ee8268 EFLAGS: 00000213 ORIG_RAX: 0000000000000133
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000441819
RDX: 0000000000000002 RSI: 0000000020000100 RDI: 0000000000000003
RBP: 00000000006cd018 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000213 R12: 0000000000402510
R13: 00000000004025a0 R14: 0000000000000000 R15: 0000000000000000
Uninit was created at:
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:278 [inline]
kmsan_internal_poison_shadow+0xb8/0x1b0 mm/kmsan/kmsan.c:188
kmsan_kmalloc+0x94/0x100 mm/kmsan/kmsan.c:314
kmsan_slab_alloc+0x11/0x20 mm/kmsan/kmsan.c:321
slab_post_alloc_hook mm/slab.h:445 [inline]
slab_alloc_node mm/slub.c:2737 [inline]
__kmalloc_node_track_caller+0xaed/0x11c0 mm/slub.c:4369
__kmalloc_reserve net/core/skbuff.c:138 [inline]
__alloc_skb+0x2cf/0x9f0 net/core/skbuff.c:206
alloc_skb include/linux/skbuff.h:984 [inline]
alloc_skb_with_frags+0x1d4/0xb20 net/core/skbuff.c:5234
sock_alloc_send_pskb+0xb56/0x1190 net/core/sock.c:2085
packet_alloc_skb net/packet/af_packet.c:2803 [inline]
packet_snd net/packet/af_packet.c:2894 [inline]
packet_sendmsg+0x6454/0x8a30 net/packet/af_packet.c:2969
sock_sendmsg_nosec net/socket.c:630 [inline]
sock_sendmsg net/socket.c:640 [inline]
___sys_sendmsg+0xec0/0x1310 net/socket.c:2046
__sys_sendmmsg+0x42d/0x800 net/socket.c:2136
SYSC_sendmmsg+0xc4/0x110 net/socket.c:2167
SyS_sendmmsg+0x63/0x90 net/socket.c:2162
do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
This change addresses the issue adding the needed check before
accessing the inner header.
The ipv4 side of the issue is apparently there since the ipv4 over ipv6
initial support, and the ipv6 side predates git history.
Fixes: c4d3efafcc93 ("[IPV6] IP6TUNNEL: Add support to IPv4 over IPv6 tunnel.")
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: syzbot+3fde91d4d394747d6db4@syzkaller.appspotmail.com
Tested-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
libc_compat.h is used by libbpf so make sure it's licensed under
LGPL or BSD license. The license change should be OK, I'm the only
author of the file.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
When dst->_metrics and f6i->fib6_metrics share the same memory, both
take reference count on the dst_metrics structure. However, when dst is
destroyed, ip6_dst_destroy() only invokes dst_destroy_metrics_generic()
which does not take care of READONLY metrics and does not release refcnt.
This causes memory leak.
Similar to ipv4 logic, the fix is to properly release refcnt and free
the memory space pointed by dst->_metrics if refcnt becomes 0.
Fixes: 93531c674315 ("net/ipv6: separate handling of FIB entries from dst based routes")
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit e70a3aad44cc8b24986687ffc98c4a4f6ecf25ea.
This change causes use-after-free on dst->_metrics.
The crash trace looks like this:
[ 97.763269] BUG: KASAN: use-after-free in ip6_mtu+0x116/0x140
[ 97.769038] Read of size 4 at addr ffff881781d2cf84 by task svw_NetThreadEv/8801
[ 97.777954] CPU: 76 PID: 8801 Comm: svw_NetThreadEv Not tainted 4.15.0-smp-DEV #11
[ 97.777956] Hardware name: Default string Default string/Indus_QC_02, BIOS 5.46.4 03/29/2018
[ 97.777957] Call Trace:
[ 97.777971] [<ffffffff895709db>] dump_stack+0x4d/0x72
[ 97.777985] [<ffffffff881651df>] print_address_description+0x6f/0x260
[ 97.777997] [<ffffffff88165747>] kasan_report+0x257/0x370
[ 97.778001] [<ffffffff894488e6>] ? ip6_mtu+0x116/0x140
[ 97.778004] [<ffffffff881658b9>] __asan_report_load4_noabort+0x19/0x20
[ 97.778008] [<ffffffff894488e6>] ip6_mtu+0x116/0x140
[ 97.778013] [<ffffffff892bb91e>] tcp_current_mss+0x12e/0x280
[ 97.778016] [<ffffffff892bb7f0>] ? tcp_mtu_to_mss+0x2d0/0x2d0
[ 97.778022] [<ffffffff887b45b8>] ? depot_save_stack+0x138/0x4a0
[ 97.778037] [<ffffffff87c38985>] ? __mmdrop+0x145/0x1f0
[ 97.778040] [<ffffffff881643b1>] ? save_stack+0xb1/0xd0
[ 97.778046] [<ffffffff89264c82>] tcp_send_mss+0x22/0x220
[ 97.778059] [<ffffffff89273a49>] tcp_sendmsg_locked+0x4f9/0x39f0
[ 97.778062] [<ffffffff881642b4>] ? kasan_check_write+0x14/0x20
[ 97.778066] [<ffffffff89273550>] ? tcp_sendpage+0x60/0x60
[ 97.778070] [<ffffffff881cb359>] ? rw_copy_check_uvector+0x69/0x280
[ 97.778075] [<ffffffff8873c65f>] ? import_iovec+0x9f/0x430
[ 97.778078] [<ffffffff88164be7>] ? kasan_slab_free+0x87/0xc0
[ 97.778082] [<ffffffff8873c5c0>] ? memzero_page+0x140/0x140
[ 97.778085] [<ffffffff881642b4>] ? kasan_check_write+0x14/0x20
[ 97.778088] [<ffffffff89276f6c>] tcp_sendmsg+0x2c/0x50
[ 97.778092] [<ffffffff89276f6c>] ? tcp_sendmsg+0x2c/0x50
[ 97.778098] [<ffffffff89352d43>] inet_sendmsg+0x103/0x480
[ 97.778102] [<ffffffff89352c40>] ? inet_gso_segment+0x15b0/0x15b0
[ 97.778105] [<ffffffff890294da>] sock_sendmsg+0xba/0xf0
[ 97.778108] [<ffffffff8902ab6a>] ___sys_sendmsg+0x6ca/0x8e0
[ 97.778113] [<ffffffff87dccac1>] ? hrtimer_try_to_cancel+0x71/0x3b0
[ 97.778116] [<ffffffff8902a4a0>] ? copy_msghdr_from_user+0x3d0/0x3d0
[ 97.778119] [<ffffffff881646d1>] ? memset+0x31/0x40
[ 97.778123] [<ffffffff87a0cff5>] ? schedule_hrtimeout_range_clock+0x165/0x380
[ 97.778127] [<ffffffff87a0ce90>] ? hrtimer_nanosleep_restart+0x250/0x250
[ 97.778130] [<ffffffff87dcc700>] ? __hrtimer_init+0x180/0x180
[ 97.778133] [<ffffffff87dd1f82>] ? ktime_get_ts64+0x172/0x200
[ 97.778137] [<ffffffff8822b8ec>] ? __fget_light+0x8c/0x2f0
[ 97.778141] [<ffffffff8902d5c6>] __sys_sendmsg+0xe6/0x190
[ 97.778144] [<ffffffff8902d5c6>] ? __sys_sendmsg+0xe6/0x190
[ 97.778147] [<ffffffff8902d4e0>] ? SyS_shutdown+0x20/0x20
[ 97.778152] [<ffffffff87cd4370>] ? wake_up_q+0xe0/0xe0
[ 97.778155] [<ffffffff8902d670>] ? __sys_sendmsg+0x190/0x190
[ 97.778158] [<ffffffff8902d683>] SyS_sendmsg+0x13/0x20
[ 97.778162] [<ffffffff87a1600c>] do_syscall_64+0x2ac/0x430
[ 97.778166] [<ffffffff87c17515>] ? do_page_fault+0x35/0x3d0
[ 97.778171] [<ffffffff8960131f>] ? page_fault+0x2f/0x50
[ 97.778174] [<ffffffff89600071>] entry_SYSCALL_64_after_hwframe+0x3d/0xa2
[ 97.778177] RIP: 0033:0x7f83fa36000d
[ 97.778178] RSP: 002b:00007f83ef9229e0 EFLAGS: 00000293 ORIG_RAX: 000000000000002e
[ 97.778180] RAX: ffffffffffffffda RBX: 0000000000000001 RCX: 00007f83fa36000d
[ 97.778182] RDX: 0000000000004000 RSI: 00007f83ef922f00 RDI: 0000000000000036
[ 97.778183] RBP: 00007f83ef923040 R08: 00007f83ef9231f8 R09: 00007f83ef923168
[ 97.778184] R10: 0000000000000000 R11: 0000000000000293 R12: 00007f83f69c5b40
[ 97.778185] R13: 000000000000001c R14: 0000000000000001 R15: 0000000000004000
[ 97.779684] Allocated by task 5919:
[ 97.783185] save_stack+0x46/0xd0
[ 97.783187] kasan_kmalloc+0xad/0xe0
[ 97.783189] kmem_cache_alloc_trace+0xdf/0x580
[ 97.783190] ip6_convert_metrics.isra.79+0x7e/0x190
[ 97.783192] ip6_route_info_create+0x60a/0x2480
[ 97.783193] ip6_route_add+0x1d/0x80
[ 97.783195] inet6_rtm_newroute+0xdd/0xf0
[ 97.783198] rtnetlink_rcv_msg+0x641/0xb10
[ 97.783200] netlink_rcv_skb+0x27b/0x3e0
[ 97.783202] rtnetlink_rcv+0x15/0x20
[ 97.783203] netlink_unicast+0x4be/0x720
[ 97.783204] netlink_sendmsg+0x7bc/0xbf0
[ 97.783205] sock_sendmsg+0xba/0xf0
[ 97.783207] ___sys_sendmsg+0x6ca/0x8e0
[ 97.783208] __sys_sendmsg+0xe6/0x190
[ 97.783209] SyS_sendmsg+0x13/0x20
[ 97.783211] do_syscall_64+0x2ac/0x430
[ 97.783213] entry_SYSCALL_64_after_hwframe+0x3d/0xa2
[ 97.784709] Freed by task 0:
[ 97.785056] knetbase: Error: /proc/sys/net/core/txcs_enable does not exist
[ 97.794497] save_stack+0x46/0xd0
[ 97.794499] kasan_slab_free+0x71/0xc0
[ 97.794500] kfree+0x7c/0xf0
[ 97.794501] fib6_info_destroy_rcu+0x24f/0x310
[ 97.794504] rcu_process_callbacks+0x38b/0x1730
[ 97.794506] __do_softirq+0x1c8/0x5d0
Reported-by: John Sperbeck <jsperbeck@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a network interface is created prior to the SFP socket being
available, ethtool can request module information. This unfortunately
leads to an oops:
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = (ptrval)
[00000008] *pgd=7c400831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1480 Comm: ethtool Not tainted 4.19.0-rc3 #138
Hardware name: Broadcom Northstar Plus SoC
PC is at sfp_get_module_info+0x8/0x10
LR is at dev_ethtool+0x218c/0x2afc
Fix this by not filling in the network device's SFP bus pointer until
SFP is fully bound, thereby avoiding the core calling into the SFP bus
code.
Fixes: ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices and sfp cages")
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When no Tx IRQ is available, the txq_done() routine (called from
tx_done()) shouldn't be called from the polling function, as in such
case it is already called in the Tx path thanks to an hrtimer. This
mostly occurred when using PPv2.1, as the engine then do not have Tx
IRQs.
Fixes: edc660fa09e2 ("net: mvpp2: replace TX coalescing interrupts with hrtimer")
Reported-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Saif Hasan
Friedemann Gerold
Eric Dumazet
David S. Miller
Maciej Żenczykowski
Nathan Chancellor
Dan Carpenter
YueHaibing
Wei Yongjun
Jeff Barnhill
Sean Tranchetti
John Fastabend
Antoine Tenart
Heiner Kallweit
Xin Long
Davide Caratti
Johannes Berg
Petr Machata
Sudarsana Reddy Kalluru
Paolo Abeni
Jakub Kicinski
Wei Wang
Russell King