Age | Commit message (Collapse) | Author | Files | Lines |
|
unhalt Instrction Fetch Unit after all rings are inited.
Signed-off-by: JimQu <Jim.Qu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
SDMA could be fail in the thaw() and restore() processes, do software reset
if each SDMA engine is busy.
Signed-off-by: JimQu <Jim.Qu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
We used to delay switching to the new credentials until after we had
mapped the executable (and possible elf interpreter). That was kind of
odd to begin with, since the new executable will actually then _run_
with the new creds, but whatever.
The bigger problem was that we also want to make sure that we turn off
prof events and tracing before we start mapping the new executable
state. So while this is a cleanup, it's also a fix for a possible
information leak.
Reported-by: Robert Święcki <robert@swiecki.net>
Tested-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Kees Cook <keescook@chromium.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Added devices ids for acces i/o products quad and octal serial cards
that make use of existing Pericom PI7C9X7954 and PI7C9X7958
configurations .
Signed-off-by: Jimi Damon <jdamon@accesio.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since the commit c1a67b48f6a5 ("serial: 8250_pci: replace switch-case by
formula for Intel MID"), the 8250 driver crashes in the byt_set_termios()
function with a divide error. This is caused by the fact that a baud rate of 0
(B0) is not handled properly. Fix it by falling back to B9600 in this case.
Reported-by: "Mendez Salinas, Fernando" <fernando.mendez.salinas@intel.com>
Fixes: c1a67b48f6a5 ("serial: 8250_pci: replace switch-case by formula for Intel MID")
Cc: stable@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Serial console is broken in v4.8-rcX. Mika and I independently bisected down to
commit 4ef03d328769 ("tty/serial/8250: use mctrl_gpio helpers").
Since neither author nor anyone else didn't propose a solution we better revert
it for now.
This reverts commit 4ef03d328769eddbfeca1f1c958fdb181a69c341.
Link: https://lkml.kernel.org/r/20160809130229.GN1729@lahna.fi.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Attributes declared with __ATTR_PREALLOC use sysfs_kf_read() which returns
zero bytes for non-zero offset. This breaks script checkarray in mdadm tool
in debian where /bin/sh is 'dash' because its builtin 'read' reads only one
byte at a time. Script gets 'i' instead of 'idle' when reads current action
from /sys/block/$dev/md/sync_action and as a result does nothing.
This patch adds trivial implementation of partial read: generate whole
string and move required part into buffer head.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Fixes: 4ef67a8c95f3 ("sysfs/kernfs: make read requests on pre-alloc files use the buffer.")
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=787950
Cc: Stable <stable@vger.kernel.org> # v3.19+
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5590f3196b29 ("drivers/core/of: Add symlink to device-tree from
devices with an OF node") added a symlink called "of_node" to sysfs
however the documentation describes it as "of_path".
Fix the documentation to match what the code actually does.
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kernfs_notify_workfn() sends out file modified events for the
scheduled kernfs_nodes. Because the modifications aren't from
userland, it doesn't have the matching file struct at hand and can't
use fsnotify_modify(). Instead, it looked up the inode and then used
d_find_any_alias() to find the dentry and used fsnotify_parent() and
fsnotify() directly to generate notifications.
The assumption was that the relevant dentries would have been pinned
if there are listeners, which isn't true as inotify doesn't pin
dentries at all and watching the parent doesn't pin the child dentries
even for dnotify. This led to, for example, inotify watchers not
getting notifications if the system is under memory pressure and the
matching dentries got reclaimed. It can also be triggered through
/proc/sys/vm/drop_caches or a remount attempt which involves shrinking
dcache.
fsnotify_parent() only uses the dentry to access the parent inode,
which kernfs can do easily. Update kernfs_notify_workfn() so that it
uses fsnotify() directly for both the parent and target inodes without
going through d_find_any_alias(). While at it, supply the target file
name to fsnotify() from kernfs_node->name.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Evgeny Vereshchagin <evvers@ya.ru>
Fixes: d911d9874801 ("kernfs: make kernfs_notify() trigger inotify events too")
Cc: John McCutchan <john@johnmccutchan.com>
Cc: Robert Love <rlove@rlove.org>
Cc: Eric Paris <eparis@parisplace.org>
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Falcon Ridge 4C has been supported by the driver from the beginning,
Falcon Ridge 2C support was just added. Don't irritate users with a
warning declaring the opposite.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
From: Xavier Gnata <xavier.gnata@gmail.com>
Add support to INTEL_FALCON_RIDGE_2C controller and corresponding quirk
to support suspend/resume.
Tested against 4.7 master on a MacBook Air 11" 2015.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The quirk 'quirk_apple_wait_for_thunderbolt' did not fire on Falcon
Ridge 4C controllers with subdevice/subvendor set to zero. This lead
to lost pci devices on system resume.
Older thunderbolt controllers (pre Falcon Ridge) used the same device id
for bridges and for the controller. On Apple hardware the subvendor- &
subdevice-ids were set for the controller, but not for bridges. So that
is what was used to differentiate between the two. Starting with Falcon
Ridge bridges and controllers received different device ids.
Additionally on some MacBookPro models (but not all) the
subvendor/subdevice was zeroed.
Starting with a42fb351c (thunderbolt: Allow loading of module on recent
Apple MacBooks with thunderbolt 2 controller) the thunderbolt driver
binds to all Falcon Ridge 4C controllers (irregardless of
subvendor/subdevice). The corresponding quirk was not updated.
This commit changes the quirk to check the device class instead of its
subvendor-/subdeviceids. This works for all generations of Thunderbolt
controllers.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
lkdtm_rodata_do_nothing() is an empty function which is generated in
order to test the non-executability of rodata.
Currently if function tracing is enabled then an mcount callsite will be
generated for lkdtm_rodata_do_nothing(), and it will appear in the list
of available functions for function tracing (available_filter_functions).
Given it's purpose purely as a test function, it seems preferable for
lkdtm_rodata_do_nothing() to be marked notrace, so it doesn't appear as
traceable.
This also avoids triggering a linker bug on powerpc:
https://sourceware.org/bugzilla/show_bug.cgi?id=20428
When the linker sees code that needs to generate a call stub, eg. a
branch to mcount(), it assumes the section is executable and
dereferences a NULL pointer leading to a linker segfault. Marking
lkdtm_rodata_do_nothing() notrace avoids triggering the bug because the
function contains no other function calls.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Even if PR3 support is available on the bridge, it will not be used if
the PCI layer considers it unavailable (i.e. on all laptops from 2013
and 2014). Ensure that this condition is checked to allow a fallback to
the Optimus DSM for device poweroff.
Initially I wanted to call pci_d3cold_enable before checking bridge_d3
(in case the user changed d3cold_allowed), but that is such an unlikely
case and likely fragile anyway. The current patch is suggested by Mika
in http://www.spinics.net/lists/linux-pci/msg52599.html
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This commit appends a few _rcuidle suffixes to fix the following
RCU-used-from-idle bug:
> ===============================
> [ INFO: suspicious RCU usage. ]
> 4.6.0-rc5-next-20160426+ #1116 Not tainted
> -------------------------------
> include/trace/events/rpm.h:95 suspicious rcu_dereference_check() usage!
>
> other info that might help us debug this:
>
>
> RCU used illegally from idle CPU!
> rcu_scheduler_active = 1, debug_locks = 0
> RCU used illegally from extended quiescent state!
> 1 lock held by swapper/0/0:
> #0: (&(&dev->power.lock)->rlock){-.-...}, at: [<c052cc2c>] __rpm_callback+0x58/0x60
>
> stack backtrace:
> CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.6.0-rc5-next-20160426+ #1116
> Hardware name: Generic OMAP36xx (Flattened Device Tree)
> [<c0110290>] (unwind_backtrace) from [<c010c3a8>] (show_stack+0x10/0x14)
> [<c010c3a8>] (show_stack) from [<c047fd68>] (dump_stack+0xb0/0xe4)
> [<c047fd68>] (dump_stack) from [<c052d5d0>] (rpm_suspend+0x580/0x768)
> [<c052d5d0>] (rpm_suspend) from [<c052ec58>] (__pm_runtime_suspend+0x64/0x84)
> [<c052ec58>] (__pm_runtime_suspend) from [<c04bf25c>] (omap2_gpio_prepare_for_idle+0x5c/0x70)
> [<c04bf25c>] (omap2_gpio_prepare_for_idle) from [<c0125568>] (omap_sram_idle+0x140/0x244)
> [<c0125568>] (omap_sram_idle) from [<c01269dc>] (omap3_enter_idle_bm+0xfc/0x1ec)
> [<c01269dc>] (omap3_enter_idle_bm) from [<c0601bdc>] (cpuidle_enter_state+0x80/0x3d4)
> [<c0601bdc>] (cpuidle_enter_state) from [<c0183b08>] (cpu_startup_entry+0x198/0x3a0)
> [<c0183b08>] (cpu_startup_entry) from [<c0b00c0c>] (start_kernel+0x354/0x3c8)
> [<c0b00c0c>] (start_kernel) from [<8000807c>] (0x8000807c)
In the immortal words of Steven Rostedt, "*Whack* *Whack* *Whack*!!!"
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
WhACKED-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This commit applies another _rcuidle suffix to fix an RCU use from
idle.
> ===============================
> [ INFO: suspicious RCU usage. ]
> 4.6.0-rc5-next-20160426+ #1122 Not tainted
> -------------------------------
> include/trace/events/rpm.h:69 suspicious rcu_dereference_check() usage!
>
> other info that might help us debug this:
>
>
> RCU used illegally from idle CPU!
> rcu_scheduler_active = 1, debug_locks = 0
> RCU used illegally from extended quiescent state!
> 1 lock held by swapper/0/0:
> #0: (&(&dev->power.lock)->rlock){-.-...}, at: [<c052e3dc>] __pm_runtime_resume+0x3c/0x64
>
> stack backtrace:
> CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.6.0-rc5-next-20160426+ #1122
> Hardware name: Generic OMAP36xx (Flattened Device Tree)
> [<c0110290>] (unwind_backtrace) from [<c010c3a8>] (show_stack+0x10/0x14)
> [<c010c3a8>] (show_stack) from [<c047fd68>] (dump_stack+0xb0/0xe4)
> [<c047fd68>] (dump_stack) from [<c052e178>] (rpm_resume+0x5cc/0x7f4)
> [<c052e178>] (rpm_resume) from [<c052e3ec>] (__pm_runtime_resume+0x4c/0x64)
> [<c052e3ec>] (__pm_runtime_resume) from [<c04bf2c4>] (omap2_gpio_resume_after_idle+0x54/0x68)
> [<c04bf2c4>] (omap2_gpio_resume_after_idle) from [<c01269dc>] (omap3_enter_idle_bm+0xfc/0x1ec)
> [<c01269dc>] (omap3_enter_idle_bm) from [<c060198c>] (cpuidle_enter_state+0x80/0x3d4)
> [<c060198c>] (cpuidle_enter_state) from [<c0183b08>] (cpu_startup_entry+0x198/0x3a0)
> [<c0183b08>] (cpu_startup_entry) from [<c0b00c0c>] (start_kernel+0x354/0x3c8)
> [<c0b00c0c>] (start_kernel) from [<8000807c>] (0x8000807c)
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Make sure of_device_id tables are NULL terminated.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Fixes: f56aad1d98f1 (cpufreq: dt: Add generic platform-device creation support)
CC: 4.7+ <stable@vger.kernel.org> # 4.7+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The workqueue "dm_bufio_wq" queues a single work item &dm_bufio_work so
it doesn't require execution ordering. Hence, alloc_workqueue() has
been used to replace the deprecated create_singlethread_workqueue().
The WQ_MEM_RECLAIM flag has been set since DM requires forward progress
under memory pressure.
Since there are fixed number of work items, explicit concurrency
limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
If crypt_alloc_tfms() had to allocate multiple tfms and it failed before
the last allocation, then it would call crypt_free_tfms() and could free
pointers from uninitialized memory -- due to the crypt_free_tfms() check
for non-zero cc->tfms[i]. Fix by allocating zeroed memory.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
|
|
When dm-crypt processes writes, it allocates a new bio in
crypt_alloc_buffer(). The bio is allocated from a bio set and it can
have at most BIO_MAX_PAGES vector entries, however the incoming bio can be
larger (e.g. if it was allocated by bcache). If the incoming bio is
larger, bio_alloc_bioset() fails and an error is returned.
To avoid the error, we test for a too large bio in the function
crypt_map() and use dm_accept_partial_bio() to split the bio.
dm_accept_partial_bio() trims the current bio to the desired size and
asks DM core to send another bio with the rest of the data.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # v3.16+
|
|
The kthread_run() function returns either a valid task_struct or
ERR_PTR() value, check for NULL is invalid. This change fixes potential
for oops, e.g. in OOM situation.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
|
|
This fixes a ptrace vs fatal pending signals bug as manifested in
seccomp now that seccomp was reordered to happen after ptrace. The
short version is that seccomp should not attempt to call do_exit()
while fatal signals are pending under a tracer. The existing code was
trying to be as defensively paranoid as possible, but it now ends up
confusing ptrace. Instead, the syscall can just be skipped (which solves
the original concern that the do_exit() was addressing) and normal signal
handling, tracer notification, and process death can happen.
Paraphrasing from the original bug report:
If a tracee task is in a PTRACE_EVENT_SECCOMP trap, or has been resumed
after such a trap but not yet been scheduled, and another task in the
thread-group calls exit_group(), then the tracee task exits without the
ptracer receiving a PTRACE_EVENT_EXIT notification. Test case here:
https://gist.github.com/khuey/3c43ac247c72cef8c956ca73281c9be7
The bug happens because when __seccomp_filter() detects
fatal_signal_pending(), it calls do_exit() without dequeuing the fatal
signal. When do_exit() sends the PTRACE_EVENT_EXIT notification and
that task is descheduled, __schedule() notices that there is a fatal
signal pending and changes its state from TASK_TRACED to TASK_RUNNING.
That prevents the ptracer's waitpid() from returning the ptrace event.
A more detailed analysis is here:
https://github.com/mozilla/rr/issues/1762#issuecomment-237396255.
Reported-by: Robert O'Callahan <robert@ocallahan.org>
Reported-by: Kyle Huey <khuey@kylehuey.com>
Tested-by: Kyle Huey <khuey@kylehuey.com>
Fixes: 93e35efb8de4 ("x86/ptrace: run seccomp after ptrace")
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: James Morris <james.l.morris@oracle.com>
|
|
bio_alloc() can allocate a bio with at most BIO_MAX_PAGES (256) vector
entries. However, the incoming bio may have more vector entries if it
was allocated by other means. For example, bcache submits bios with
more than BIO_MAX_PAGES entries. This results in bio_alloc() failure.
To avoid the failure, change the code so that it allocates bio with at
most BIO_MAX_PAGES entries. If the incoming bio has more entries,
bio_add_page() will fail and a new bio will be allocated - the code that
handles bio_add_page() failure already exists in the dm-log-writes
target.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Josef Bacik <jbacik@fb,com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # v4.1+
|
|
Move log_one_block()'s atomic_inc(&lc->io_blocks) before bio_alloc() to
fix a bug that the target hangs if bio_alloc() fails. The error path
does put_io_block(lc), so atomic_inc(&lc->io_blocks) must occur before
invoking the error path to avoid underflow of lc->io_blocks.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Josef Bacik <jbacik@fb,com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
|
|
There are three usercopy warnings which are currently being silenced for
gcc 4.6 and newer:
1) "copy_from_user() buffer size is too small" compile warning/error
This is a static warning which happens when object size and copy size
are both const, and copy size > object size. I didn't see any false
positives for this one. So the function warning attribute seems to
be working fine here.
Note this scenario is always a bug and so I think it should be
changed to *always* be an error, regardless of
CONFIG_DEBUG_STRICT_USER_COPY_CHECKS.
2) "copy_from_user() buffer size is not provably correct" compile warning
This is another static warning which happens when I enable
__compiletime_object_size() for new compilers (and
CONFIG_DEBUG_STRICT_USER_COPY_CHECKS). It happens when object size
is const, but copy size is *not*. In this case there's no way to
compare the two at build time, so it gives the warning. (Note the
warning is a byproduct of the fact that gcc has no way of knowing
whether the overflow function will be called, so the call isn't dead
code and the warning attribute is activated.)
So this warning seems to only indicate "this is an unusual pattern,
maybe you should check it out" rather than "this is a bug".
I get 102(!) of these warnings with allyesconfig and the
__compiletime_object_size() gcc check removed. I don't know if there
are any real bugs hiding in there, but from looking at a small
sample, I didn't see any. According to Kees, it does sometimes find
real bugs. But the false positive rate seems high.
3) "Buffer overflow detected" runtime warning
This is a runtime warning where object size is const, and copy size >
object size.
All three warnings (both static and runtime) were completely disabled
for gcc 4.6 with the following commit:
2fb0815c9ee6 ("gcc4: disable __compiletime_object_size for GCC 4.6+")
That commit mistakenly assumed that the false positives were caused by a
gcc bug in __compiletime_object_size(). But in fact,
__compiletime_object_size() seems to be working fine. The false
positives were instead triggered by #2 above. (Though I don't have an
explanation for why the warnings supposedly only started showing up in
gcc 4.6.)
So remove warning #2 to get rid of all the false positives, and re-enable
warnings #1 and #3 by reverting the above commit.
Furthermore, since #1 is a real bug which is detected at compile time,
upgrade it to always be an error.
Having done all that, CONFIG_DEBUG_STRICT_USER_COPY_CHECKS is no longer
needed.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Byungchul Park <byungchul.park@lge.com>
Cc: Nilay Vaish <nilayvaish@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Ninja32 needs to set some flags to indicate it does 32bit IO. However it currently assigns this which
loses the initializing flag and causes a warning spew. Fix it to use a logical or as is intended.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Tested-by: Ellmar Stelnberger <estellnb@elstel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
On error, the callers expect us to return without bumping
nn->cb_users[].
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Cc: stable@vger.kernel.org # v3.7+
|
|
If a server returns itself as a location while migrating, the client may
end up getting stuck attempting to migrate twice to the same server. Catch
this by checking if the nfs_client found is the same as the existing
client. For the other two callers to nfs4_set_client, the nfs_client will
always be ERR_PTR(-EINVAL).
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
Sunrise Point PCH with SPS Firmware doesn't expose working
MEI interface, we need to quirk it out.
The SPS Firmware is identifiable only on the first PCI function
of the device.
Cc: <stable@vger.kernel.org> #4.6+
Tested-by: Sujith Pandel <sujith_pandel@dell.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If we have USB gadgets disabled and USB_MUSB_HOST set, we get
errors "possible irq lock inverssion dependency detected"
errors during boot.
Let's fix the issue by adding start_musb flag and start
the controller after we're out of the spinlock protected
section.
Reported-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The atomic conversion lost the notification to let the DRM core
know about the current state of the CRTC vblank interrupts. This
regressed the ability of the core to reject page flip attempts
on currently disabled CRTCs. Add back the notifications.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Christoph reports slab corruption when a deferred refcount update
aborts during _defer_finish(). The cause of this was broken log item
state tracking in xfs_defer_pending -- upon an abort,
_defer_trans_abort() will call abort_intent on all intent items,
including the ones that have already had a done item attached.
This is incorrect because each intent item has 2 refcount: the first
is released when the intent item is committed to the log; and the
second is released when the _done_ item is committed to the log, or
by the intent creator if there is no done item. In other words, once
we log the done item, responsibility for releasing the intent item's
second refcount is transferred to the done item and /must not/ be
performed by anything else.
The dfp_committed flag should have been tracking whether or not we had
a done item so that _defer_trans_abort could decide if it needs to
abort the intent item, but due to a thinko this was not the case. Rip
it out and track the done item directly so that we do the right thing
w.r.t. intent item freeing.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reported-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
|
|
If the attempt to connect to a DS fails inside ff_layout_pg_init_read or
ff_layout_pg_init_write, then we currently end up clearing the layout
segment carried by the struct nfs_pageio_descriptor, causing an Oops
when we later call into ff_layout_read_pagelist/ff_layout_write_pagelist.
The fix is to ensure we return the layout and then retry.
Fixes: 446ca2195303 ("pNFS/flexfiles: When initing reads or writes, we...")
Cc: stable@vger.kernel.org # v4.7+
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
We don't support configuring active plane on-the-fly for imx-drm.
The relevant CRTC should be disabled before the plane configuration.
Of course, the plane itself should be disabled as well.
This patch adds active plane reconfiguration support by forcing CRTC
mode change and disabling-enabling plane in plane's ->atomic_update
callback.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Tested-by: Peter Senna Tschudin <peter.senna@gmail.com>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Attribute array it87_attributes_in lacks its NULL terminator,
causing random behavior when operating on the attribute group.
Fixes: 52929715634a ("hwmon: (it87) Use is_visible for voltage sensors")
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The previous fix introduced a check against the ret variable which
is not defined, hence producing a compilation error:
linux/drivers/clocksource/timer-atmel-pit.c: In function ‘at91sam926x_pit_dt_init’:
linux/drivers/clocksource/timer-atmel-pit.c:264:2: error: ‘ret’ undeclared (first use in this function)
ret = clk_prepare_enable(data->mck);
^
linux/drivers/clocksource/timer-atmel-pit.c:264:2: note: each undeclared identifier is reported only once for each function it appears in
Add the missing the variable 'ret'.
Fixes: 504f34c9e45c "clocksource/drivers/atmel-pit: Convert init function to return error"
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: alexandre.belloni@free-electrons.com
Cc: motobud@gmail.com
Cc: realbright@lgcns.com
Link: http://lkml.kernel.org/r/1472453043-24287-1-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The Kconfig entry controlling compilation of this code is:
drivers/platform/x86/Kconfig:config GPIO_INTEL_PMIC
drivers/platform/x86/Kconfig: bool "Intel PMIC GPIO support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
We don't replace module.h with init.h since the file already has that.
Cc: Alek Du <alek.du@intel.com>
Cc: platform-driver-x86@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
|
|
The Kconfig entry controlling compilation of this code is:
arch/x86/Kconfig:config OLPC
arch/x86/Kconfig: bool "One Laptop Per Child support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: platform-driver-x86@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit b70661c70830 ("net: smc91x: use run-time configuration on all ARM
machines") broke some ARM platforms through several mistakes. Firstly,
the access size must correspond to the following rule:
(a) at least one of 16-bit or 8-bit access size must be supported
(b) 32-bit accesses are optional, and may be enabled in addition to
the above.
Secondly, it provides no emulation of 16-bit accesses, instead blindly
making 16-bit accesses even when the platform specifies that only 8-bit
is supported.
Reorganise smc91x.h so we can make use of the existing 16-bit access
emulation already provided - if 16-bit accesses are supported, use
16-bit accesses directly, otherwise if 8-bit accesses are supported,
use the provided 16-bit access emulation. If neither, BUG(). This
exactly reflects the driver behaviour prior to the commit being fixed.
Since the conversion incorrectly cut down the available access sizes on
several platforms, we also need to go through every platform and fix up
the overly-restrictive access size: Arnd assumed that if a platform can
perform 32-bit, 16-bit and 8-bit accesses, then only a 32-bit access
size needed to be specified - not so, all available access sizes must
be specified.
This likely fixes some performance regressions in doing this: if a
platform does not support 8-bit accesses, 8-bit accesses have been
emulated by performing a 16-bit read-modify-write access.
Tested on the Intel Assabet/Neponset platform, which supports only 8-bit
accesses, which was broken by the original commit.
Fixes: b70661c70830 ("net: smc91x: use run-time configuration on all ARM machines")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 83c0afaec7b7 ("net: dsa: Add new binding implementation"),
the shortcomings of the dsa platform device have been addressed, remove
that TODO item.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ethtool has 11 flow tables, each flow table has its own priority.
Increase the number of priorities to be aligned with the number of flow
tables.
Fixes: 1174fce8d141 ('net/mlx5e: Support l3/l4 flow type specs in ethtool flow steering')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Upon set ETS failure due to user invalid input, add error prints to
specify the exact error to the user.
Fixes: cdcf11212b22 ('net/mlx5e: Validate BW weight values of ETS')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Free 'in' command object also when mlx5_core_modify_tir fails.
Fixes: 724b2aa15126 ("net/mlx5e: TIRs management refactoring")
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a counter in ethtool for the number of times that
TX xmit_more was used.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver RQ has two possible configurations: striding RQ and
non-striding RQ. Until this patch, the driver always reported the
number of hardware WQEs (ring descriptors). For non striding RQ
configuration, this was OK since we have one WQE per pending packet
For striding RQ, multiple packets can fit into one WQE. For better
user experience we normalize the rx_pending parameter (size of wqe/mtu)
as the average ring size in case of striding RQ.
Fixes: 461017cb006a ('net/mlx5e: Support RX multi-packet WQE ...')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of asking the firmware to flush the SQ (Send Queue) via
asynchronous completions when moved to error, we handle SQ flush
manually (mlx5e_free_tx_descs) same as we did when SQ flush got
timed out or on tx_timeout.
This will reduce SQs flush time and speedup interface down procedure.
Moved mlx5e_free_tx_descs to the end of en_tx.c for tx
critical code locality.
Fixes: 29429f3300a3 ('net/mlx5e: Timeout if SQ doesn't flush during close')
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ICO (Internal control operations) SQ (Send Queue) is closed/disabled
after RQ (Receive Queue). After RQ is closed an ICO SQ completion
might post a fragmented MPWQE (Multi Packet Work Queue Element) into
that RQ.
As on regular RQ post, check if we are allowed to post to that
RQ (RQ is enabled). Cleanup in-progress UMR MPWQE on mlx5e_free_rx_descs
if needed.
Fixes: bc77b240b3c5 ('net/mlx5e: Add fragmented memory support for RX multi packet WQE')
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This will significantly reduce receive queue flush time on interface
down.
Instead of asking the firmware to flush the RQ (Receive Queue) via
asynchronous completions when moved to error, we handle RQ flush
manually (mlx5e_free_rx_descs) same as we did when RQ flush got timed
out.
This will reduce RQs flush time and speedup interface down procedure
(ifconfig down) from 6 sec to 0.3 sec on a 48 cores system.
Moved mlx5e_free_rx_descs en_main.c where it is needed, to keep en_rx.c
free form non critical data path code for better code locality.
Fixes: 6cd392a082de ('net/mlx5e: Handle RQ flush in error cases')
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ConnectX-4 UMR (User Memory Region) MTT translation table offset in WQE
is limited to U16_MAX, before this patch we ignored that limitation and
requested the maximum possible UMR translation length that the netdev
might need (MAX channels * MAX pages per channel).
In case of a system with #cores > 32 and when linear WQE allocation fails,
falling back to using UMR WQEs will cause the RQ (Receive Queue) to get
stuck.
Here we limit UMR length to min(U16_MAX, max required pages) (while
considering the required alignments) on driver load, by default U16_MAX is
sufficient since the default RX rings value guarantees that we are in
range, dynamically (on set_ringparam/set_channels) we will check if the
new required UMR length (num mtts) is still in range, if not, fail the
request.
Fixes: bc77b240b3c5 ('net/mlx5e: Add fragmented memory support for RX multi packet WQE')
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|