| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.3 for MIPS. Here's the summary:
Three fixes that didn't make 4.2-stable:
- a -Os build might compile the kernel using the MIPS16 instruction
set but the R2 optimized inline functions in <uapi/asm/swab.h> are
implemented using 32-bit wide instructions which is invalid.
- a build error in pgtable-bits.h for a particular kernel
configuration.
- accessing registers of the CM GCR might have been compiled to use
64 bit accesses but these registers are onl 32 bit wide.
And also a few new bits:
- move the ATH79 GPIO driver to drivers/gpio
- the definition of IRQCHIP_DECLARE has moved to linux/irqchip.h,
change ATH79 accordingly.
- fix definition of pgprot_writecombine
- add an implementation of dma_map_ops.mmap
- fix alignment of quiet build output for vmlinuz link
- BCM47xx: Use kmemdup rather than duplicating its implementation
- Netlogic: Fix 0x0x prefixes of constants.
- merge Bjorn Helgaas' series to remove most of the weak keywords
from function declarations.
- CP0 and CP1 registers are best considered treated as unsigned
values to avoid large values from becoming negative values.
- improve support for the MIPS GIC timer.
- enable common clock framework for Malta and SEAD3.
- a number of improvments and fixes to dump_tlb().
- document the MIPS TLB dump functionality in Magic SysRq.
- Cavium Octeon CN68XX improvments.
- NetLogic improvments.
- irq: Use access helper irq_data_get_affinity_mask.
- handle MSA unaligned accesses.
- a number of R6-related math-emu fixes.
- support for I6400.
- improvments to MSA support.
- add uprobes support.
- move from deprecated __initcall to arch_initcall.
- remove finish_arch_switch().
- IRQ cleanups by Thomas Gleixner.
- migrate to new 'set-state' interface.
- random small cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (148 commits)
MIPS: UAPI: Fix unrecognized opcode WSBH/DSBH/DSHD when using MIPS16.
MIPS: Fix alignment of quiet build output for vmlinuz link
MIPS: math-emu: Remove unused handle_dsemul function declaration
MIPS: math-emu: Add support for the MIPS R6 MAX{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MIN{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 CLASS FPU instruction
MIPS: math-emu: Add support for the MIPS R6 RINT FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MSUBF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MADDF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELNEZ FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELEQZ FPU instruction
MIPS: math-emu: Add support for the CMP.condn.fmt R6 instruction
MIPS: inst.h: Add new MIPS R6 FPU opcodes
MIPS: Octeon: Fix management port MII address on Kontron S1901
MIPS: BCM47xx: Use kmemdup rather than duplicating its implementation
STAGING: Octeon: Use common helpers for determining interface and port
MIPS: Octeon: Support interfaces 4 and 5
MIPS: Octeon: Set up 1:1 mapping between CN68XX PKO queues and ports
MIPS: Octeon: Initialize CN68XX PKO
STAGING: Octeon: Support CN68XX style WQE
...
|
|
Currently CONFIG_ARCH_HAVE_CUSTOM_GPIO_H is defined for all MIPS
machines, and each machine type provides its own gpio.h. However
only a handful really implement the GPIO API, most just forward
everythings to gpiolib.
The Alchemy machine is notable as it provides a system to allow
implementing the GPIO API at the board level. But it is not used by
any board currently supported, so it can also be removed.
For most machine types we can just remove the custom gpio.h, as well
as the custom wrappers if some exists. Some of the code found in
the wrappers must be moved to the respective GPIO driver.
A few more fixes are need in some drivers as they rely on linux/gpio.h
to provides some machine specific definitions, or used asm/gpio.h
instead of linux/gpio.h for the gpio API.
Signed-off-by: Alban Bedel <albeu@free.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Daniel Walter <dwalter@google.com>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Cc: Masanari Iida <standby24x7@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Michael Buesch <m@bues.ch>
Cc: abdoulaye berthe <berthe.ab@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-ide@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: netdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10828/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Pull libata updates from Tejun Heo:
"Nothing interesting. A couple device specific minor updates and a
kernel doc change"
* 'for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: pata_arasam_cf: Use devm_clk_get
libata: fix libata-core.c kernel-doc warning
ata: sata_rcar: Remove obsolete sata-r8a779* platform_device_id entries
|
|
Pull PCI updates from Bjorn Helgaas:
"PCI changes for the v4.3 merge window:
Enumeration:
- Allocate ATS struct during enumeration (Bjorn Helgaas)
- Embed ATS info directly into struct pci_dev (Bjorn Helgaas)
- Reduce size of ATS structure elements (Bjorn Helgaas)
- Stop caching ATS Invalidate Queue Depth (Bjorn Helgaas)
- iommu/vt-d: Cache PCI ATS state and Invalidate Queue Depth (Bjorn Helgaas)
- Move MPS configuration check to pci_configure_device() (Bjorn Helgaas)
- Set MPS to match upstream bridge (Keith Busch)
- ARM/PCI: Set MPS before pci_bus_add_devices() (Murali Karicheri)
- Add pci_scan_root_bus_msi() (Lorenzo Pieralisi)
- ARM/PCI, designware, xilinx: Use pci_scan_root_bus_msi() (Lorenzo Pieralisi)
Resource management:
- Call pci_read_bridge_bases() from core instead of arch code (Lorenzo Pieralisi)
PCI device hotplug:
- pciehp: Remove unused interrupt events (Bjorn Helgaas)
- pciehp: Remove ignored MRL sensor interrupt events (Bjorn Helgaas)
- pciehp: Handle invalid data when reading from non-existent devices (Jarod Wilson)
- pciehp: Simplify pcie_poll_cmd() (Yijing Wang)
- Use "slot" and "pci_slot" for struct hotplug_slot and struct pci_slot (Yijing Wang)
- Protect pci_bus->slots with pci_slot_mutex, not pci_bus_sem (Yijing Wang)
- Hold pci_slot_mutex while searching bus->slots list (Yijing Wang)
Power management:
- Disable async suspend/resume for JMicron multi-function SATA/AHCI (Zhang Rui)
Virtualization:
- Add ACS quirks for Intel I219-LM/V (Alex Williamson)
- Restore ACS configuration as part of pci_restore_state() (Alexander Duyck)
MSI:
- Add pcibios_alloc_irq() and pcibios_free_irq() (Jiang Liu)
- x86: Implement pcibios_alloc_irq() and pcibios_free_irq() (Jiang Liu)
- Add helpers to manage pci_dev->irq and pci_dev->irq_managed (Jiang Liu)
- Free legacy IRQ when enabling MSI/MSI-X (Jiang Liu)
- ARM/PCI: Remove msi_controller from struct pci_sys_data (Lorenzo Pieralisi)
- Remove unused pcibios_msi_controller() hook (Lorenzo Pieralisi)
Generic host bridge driver:
- Remove dependency on ARM-specific struct hw_pci (Jayachandran C)
- Build setup-irq.o for arm64 (Jayachandran C)
- Add arm64 support (Jayachandran C)
APM X-Gene host bridge driver:
- Add APM X-Gene PCIe 64-bit prefetchable window (Duc Dang)
- Add support for a 64-bit prefetchable memory window (Duc Dang)
- Drop owner assignment from platform_driver (Krzysztof Kozlowski)
Broadcom iProc host bridge driver:
- Allow BCMA bus driver to be built as module (Hauke Mehrtens)
- Delete unnecessary checks before phy calls (Markus Elfring)
- Add arm64 support (Ray Jui)
Synopsys DesignWare host bridge driver:
- Don't complain missing *config* reg space if va_cfg0 is set (Murali Karicheri)
TI DRA7xx host bridge driver:
- Disable pm_runtime on get_sync failure (Kishon Vijay Abraham I)
- Add PM support (Kishon Vijay Abraham I)
- Clear MSE bit during suspend so clocks will idle (Kishon Vijay Abraham I)
- Add support to make GPIO drive PERST# line (Kishon Vijay Abraham I)
Xilinx AXI host bridge driver:
- Check for MSI interrupt flag before handling as INTx (Russell Joyce)
Miscellaneous:
- Fix Intersil/Techwell TW686[4589] AV capture class code (Krzysztof Hałasa)
- Use PCI_CLASS_SERIAL_USB instead of bare number (Bjorn Helgaas)
- Fix generic NCR 53c810 class code quirk (Bjorn Helgaas)
- Fix TI816X class code quirk (Bjorn Helgaas)
- Remove unused "pci_probe" flags (Bjorn Helgaas)
- Host bridge driver code simplifications (Fabio Estevam)
- Add dev_flags bit to access VPD through function 0 (Mark Rustad)
- Add VPD function 0 quirk for Intel Ethernet devices (Mark Rustad)
- Kill off set_irq_flags() usage (Rob Herring)
- Remove Intel Cherrytrail D3 delays (Srinidhi Kasagar)
- Clean up pci_find_capability() (Wei Yang)"
* tag 'pci-v4.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (72 commits)
PCI: Disable async suspend/resume for JMicron multi-function SATA/AHCI
PCI: Set MPS to match upstream bridge
PCI: Move MPS configuration check to pci_configure_device()
PCI: Drop references acquired by of_parse_phandle()
PCI/MSI: Remove unused pcibios_msi_controller() hook
ARM/PCI: Remove msi_controller from struct pci_sys_data
ARM/PCI, designware, xilinx: Use pci_scan_root_bus_msi()
PCI: Add pci_scan_root_bus_msi()
ARM/PCI: Replace panic with WARN messages on failures
PCI: generic: Add arm64 support
PCI: Build setup-irq.o for arm64
PCI: generic: Remove dependency on ARM-specific struct hw_pci
PCI: imx6: Simplify a trivial if-return sequence
PCI: spear: Use BUG_ON() instead of condition followed by BUG()
PCI: dra7xx: Remove unneeded use of IS_ERR_VALUE()
PCI: Remove pci_ats_enabled()
PCI: Stop caching ATS Invalidate Queue Depth
PCI: Move ATS declarations to linux/pci.h so they're all together
PCI: Clean up ATS error handling
PCI: Use pci_physfn() rather than looking up physfn by hand
...
|
|
Pull libata fixlet from Tejun Heo:
"Simple blacklist entry addition"
* 'for-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
Add factory recertified Crucial M500s to blacklist
|
|
The Crucial M500 is known to have issues with queued TRIM commands, the
factory recertified SSDs use a different model number naming convention
which causes them to get ignored by the blacklist.
The new naming convention boils down to: s/Crucial_/FC/
Signed-off-by: Guillermo A. Amaral <g@maral.me>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
|
|
On multi-function JMicron SATA/PATA/AHCI devices, the PATA controller at
function 1 doesn't work if it is powered on before the SATA controller at
function 0. The result is that PATA doesn't work after resume, and we
print messages like this:
pata_jmicron 0000:02:00.1: Refused to change power state, currently in D3
irq 17: nobody cared (try booting with the "irqpoll" option)
Async resume was introduced in v3.15 by 76569faa62c4 ("PM / sleep:
Asynchronous threads for resume_noirq"). Prior to that, we powered on
the functions in order, so this problem shouldn't happen.
e6b7e41cdd8c ("ata: Disabling the async PM for JMicron chip 363/361")
solved the problem for JMicron 361 and 363 devices. With async suspend
disabled, we always power on function 0 before function 1.
Barto then reported the same problem with a JMicron 368 (see comment #57 in
the bugzilla).
Rather than extending the blacklist piecemeal, disable async suspend for
all JMicron multi-function SATA/PATA/AHCI devices.
This quirk could stay in the ahci and pata_jmicron drivers, but it's likely
the problem will occur even if pata_jmicron isn't loaded until after the
suspend/resume. Making it a PCI quirk ensures that we'll preserve the
power-on order even if the drivers aren't loaded.
[bhelgaas: changelog, limit to multi-function, limit to IDE/ATA]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=81551
Reported-and-tested-by: Barto <mister.freeman@laposte.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.15+
|
|
This patch introduces the use of managed resource function
devm_clk_get instead of clk_get and removes corresponding call
to clk_put in the remove function.
To be compatible with the change various gotos are replaced with
direct returns, and unneeded label is dropped.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Pull libata fixes from Tejun Heo:
"Three minor device-specific fixes and revert of NCQ autosense added
during this -rc1.
It turned out that NCQ autosense as currently implemented interferes
with the usual error handling behavior. It will be revisited in the
near future"
* 'for-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: ahci_brcmstb: Fix misuse of IS_ENABLED
sata_sx4: Check return code from pdc20621_i2c_read()
Revert "libata: Implement NCQ autosense"
Revert "libata: Implement support for sense data reporting"
Revert "libata-eh: Set 'information' field for autosense"
ata: ahci_brcmstb: Fix warnings with CONFIG_PM_SLEEP=n
|
|
Fix kernel-doc warning in libata-core.c:
Warning(..//drivers/ata/libata-core.c:4763): No description found for parameter 'tag'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
While IS_ENABLED() is perfectly fine for CONFIG_* symbols, it is not
for other symbols such as __BIG_ENDIAN that is provided directly by
the compiler.
Switch to use CONFIG_CPU_BIG_ENDIAN instead of __BIG_ENDIAN.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
|
|
The variable spd0 might be used uninitialized when pdc20621_i2c_read()
fails. This also generates a compilation warning with gcc 5.1.
tj: use pr_err()
Signed-off-by: Tomer Barletz <barletz@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
This reverts commit 42b966fbf35da9c87f08d98f9b8978edf9e717cf.
As implemented, ACS-4 sense reporting for ATA devices bypasses error
diagnosis and handling in libata degrading EH behavior significantly.
Revert the related changes for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org #v4.1+
|
|
This reverts commit fe7173c206de63fc28475ee6ae42ff95c05692de.
As implemented, ACS-4 sense reporting for ATA devices bypasses error
diagnosis and handling in libata degrading EH behavior significantly.
Revert the related changes for now.
ATA_ID_COMMAND_SET_3/4 constants are not reverted as they're used by
later changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org #v4.1+
|
|
This reverts commit a1524f226a02aa6edebd90ae0752e97cfd78b159.
As implemented, ACS-4 sense reporting for ATA devices bypasses error
diagnosis and handling in libata degrading EH behavior significantly.
Revert the related changes for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org #v4.1+
|
|
When CONFIG_PM_SLEEP is disabled, brcm_ahci_{suspend,resume} are not
used, which causes such a build warning to occur:
CC drivers/ata/ahci_brcmstb.o
drivers/ata/ahci_brcmstb.c:212:12: warning: 'brcm_ahci_suspend' defined
but not used [-Wunused-function]
static int brcm_ahci_suspend(struct device *dev)
^
drivers/ata/ahci_brcmstb.c:224:12: warning: 'brcm_ahci_resume' defined
but not used [-Wunused-function]
static int brcm_ahci_resume(struct device *dev)
^
LD drivers/ata/built-in.o
Fixes: 766a2d979632 ("ata: add Broadcom AHCI SATA3 driver for STB chips")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Pull libata fixes from Tejun Heo:
"A couple important fixes.
- A block layer change which removed restriction on max transfer size
led to silent data corruption on some devices. A new quirk is
added to restore the old size limit for the reported device. If it
gets reported on more devices, we might have to consider restoring
the restriction for ATA devices by default.
- There finally is a SSD which is confirmed to cause data corruption
on TRIM regardless of which flavor is used. A new quirk is added
and the device is blacklisted
- Other device-specific workarounds"
* 'for-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: Do not blacklist M510DC
libata: increase the timeout when setting transfer mode
libata: add ATA_HORKAGE_MAX_SEC_1024 to revert back to previous max_sectors limit
libata: force disable trim for SuperSSpeed S238
libata: add ATA_HORKAGE_NOTRIM
libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for HP 250GB SATA disk VB0250EAVER
ata: pmp: add quirk for Marvell 4140 SATA PMP
|
|
Switch to my kernel.org alias instead of a badly named gmail address,
which I rarely use.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A new Micron drive was just announced, once again recycling the first
part of the model string. Add an underscore to the M510/M550 pattern to
avoid picking up the new DC drive.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
I have a ST4000DM000 disk. If Linux is booted while the disk is spun down,
the command that sets transfer mode causes the disk to spin up. The
spin-up takes longer than the default 5s timeout, so the command fails and
timeout is reported.
Fix this by increasing the timeout to 15s, which is enough for the disk to
spin up.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Since no longer limiting max_sectors to BLK_DEF_MAX_SECTORS (commit 34b48db66e08),
data corruption may occur on ST380013AS drive configured on 82801JI (ICH10 Family)
SATA controller. This patch will allow the driver to limit max_sectors as before
# cat /sys/block/sdb/queue/max_sectors_kb
512
I was able to double the max_sectors_kb value up to 16384 on linux-4.2.0-rc2
before seeing corruption, but seems safer to use previous limit. Without this
patch max_sectors_kb will be 32767.
tj: Minor comment update.
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org # v3.19 and later
Fixes: 34b48db66e08 ("block: remove artifical max_hw_sectors cap")
|
|
This device loses blocks, often the partition table area, on trim.
Disable TRIM.
http://pcengines.ch/msata16a.htm
Signed-off-by: Arne Fitzenreiter <arne_f@ipfire.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
|
|
Some devices lose data on TRIM whether queued or not. This patch adds
a horkage to disable TRIM.
tj: Collapsed unnecessary if() nesting.
Signed-off-by: Arne Fitzenreiter <arne_f@ipfire.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
|
|
Enabling AA on HP 250GB SATA disk VB0250EAVER causes errors:
[ 3.788362] ata3.00: failed to enable AA (error_mask=0x1)
[ 3.789243] ata3.00: failed to enable AA (error_mask=0x1)
Add the ATA_HORKAGE_BROKEN_FPDMA_AA for this specific harddisk.
tj: Collected FPDMA_AA entries and updated comment.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
|
|
This commit adds the necessary quirk to make the Marvell 4140 SATA PMP
work properly. This PMP doesn't like SRST on port number 4 (the host
port) so this commit marks this port as not supporting SRST.
Signed-off-by: Lior Amsalem <alior@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
|
|
Since commit a483dcbfa21f919c ("ARM: shmobile: lager: Remove legacy
board support"), R-Car Gen2 SoCs are only supported in generic DT-only
ARM multi-platform builds. The driver doesn't need to match platform
devices by name anymore, hence remove the corresponding
platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
This patch adds ACPI supports for AHCI platform driver, which uses _CLS
method to match the device.
The following is an example of ASL structure in DSDT for a SATA controller,
which contains _CLS package to be matched by the ahci_platform driver:
Device (AHC0) // AHCI Controller
{
Name(_HID, "AMDI0600")
Name (_CCA, 1)
Name (_CLS, Package (3)
{
0x01, // Base Class: Mass Storage
0x06, // Sub-Class: serial ATA
0x01, // Interface: AHCI
})
Name (_CRS, ResourceTemplate ()
{
Memory32Fixed (ReadWrite, 0xE0300000, 0x00010000)
Interrupt (ResourceConsumer, Level, ActiveHigh, Exclusive,,,) { 387 }
})
}
Also, since ATA driver should not require PCI support for ATA_ACPI,
this patch removes dependency in the driver/ata/Kconfig.
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull ARM SoC cleanups from Kevin Hilman:
"A relatively small setup of cleanups this time around, and similar to
last time the bulk of it is removal of legacy board support:
- OMAP: removal of legacy (non-DT) booting for several platforms
- i.MX: remove some legacy board files"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (36 commits)
ARM: fix EFM32 build breakage caused by cpu_resume_arm
ARM: 8389/1: Add cpu_resume_arm() for firmwares that resume in ARM state
ARM: v7 setup function should invalidate L1 cache
mach-omap2: Remove use of deprecated marco, PTR_RET in devices.c
ARM: OMAP2+: Remove calls to deprecacted marco,PTR_RET in the files,fb.c and pmu.c
ARM: OMAP2+: Constify irq_domain_ops
ARM: OMAP2+: use symbolic defines for console loglevels instead of numbers
ARM: at91: remove useless Makefile.boot
ARM: at91: remove at91rm9200_sdramc.h
ARM: at91: remove mach/at91_ramc.h and mach/at91rm9200_mc.h
ARM: at91/pm: use the atmel-mc syscon defines
pcmcia: at91_cf: Use syscon to configure the MC/smc
ARM: at91: declare the at91rm9200 memory controller as a syscon
mfd: syscon: Add Atmel MC (Memory Controller) registers definition
ARM: at91: drop sam9_smc.c
ata: at91: use syscon to configure the smc
ARM: ux500: delete static resource defines
ARM: ux500: rename ux500_map_io
ARM: ux500: look up PRCMU resource from DT
ARM: ux500: kill off L2CC static map
...
|
|
Pull libata updates from Tejun Heo:
- a number of libata core changes to better support NCQ TRIM.
- ahci now supports MSI-X in single IRQ mode to support a new
controller which doesn't implement MSI or INTX.
- ahci now supports edge-triggered IRQ mode to support a new controller
which for some odd reason did edge-triggered IRQ.
- the usual controller support additions and changes.
* 'for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (27 commits)
libata: Do not blacklist Micron M500DC
ata: ahci_mvebu: add suspend/resume support
ahci, msix: Fix build error for !PCI_MSI
ahci: Add support for Cavium's ThunderX host controller
ahci: Add generic MSI-X support for single interrupts to SATA PCI driver
libata: finally use __initconst in ata_parse_force_one()
drivers: ata: add support for Ceva sata host controller
devicetree:bindings: add devicetree bindings for ceva ahci
ahci: added support for Freescale AHCI sata
ahci: Store irq number in struct ahci_host_priv
ahci: Move interrupt enablement code to a separate function
Doc: libata: Fix spelling typo found in libata.xml
ata:sata_nv - Change 1 to true for bool type variable.
ata: add Broadcom AHCI SATA3 driver for STB chips
Documentation: devicetree: add Broadcom SATA binding
libata: Fix regression when the NCQ Send and Receive log page is absent
ata: hpt366: fix constant cast warning
ata: ahci_xgene: potential NULL dereference in probe
ata: ahci_xgene: Add AHCI Support for 2nd HW version of APM X-Gene SoC AHCI SATA Host controller.
libahci: Add support to handle HOST_IRQ_STAT as edge trigger latch.
...
|
|
Queued TRIM got disabled on Micron M500DC drives thanks to the
"Micron_M500*" pattern we had in place to accommodate the previous
generation of this drive family. Tweak the blacklist entry slightly so
we only disable queued TRIM for the non-DC variants of M500 drives.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
This commit adds suspend/resume support to the ahci_mvebu driver. The
suspend hook doesn't do anything special despite calling the generic
ahci_platform_suspend_host() function. However, the resume hook has to
restore the MBus windows configuration, as well as the regret option.
Tested on Marvell Armada 388 GP.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
It turned out the irq vector of the msix can be obtained from struct
msix_entry. This makes the lookup function for msi_desc obsolete.
This fixes a build error if PCI_MSI is unset:
drivers/ata/ahci.c: In function ‘msix_get_desc’:
drivers/ata/ahci.c:1210:2: error: ‘struct pci_dev’ has no member named ‘msi_list’
Catched by Fengguang's build bot.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
This patch adds support for Cavium's ThunderX host controller. The
controller resides on the SoC and is a AHCI compatible SATA controller
with one port, compliant with Serial ATA 3.1 and AHCI Revision 1.31.
There can exists multiple SATA controllers on the SoC.
The controller depends on MSI-X support since the PCI ECAM controller
on the SoC does not implement MSI nor lagacy intx interrupt support.
Thus, during device initialization, if MSI fails MSI-X will be used to
enable the device's interrupts.
The controller uses non-standard BAR0 for its register range. The
already existing device lookup (vendor and device id) that is already
implemented for other host controllers is used to change the PCI BAR.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
This patch adds generic MSI-X support for single interrupts to the
SATA PCI driver. MSI-X support is needed for host controller that only
have MSI-X support implemented, but no MSI or intx. This patch only
adds support for single interrupts, multiple per-port MSI-X interrupts
are not yet implemented.
The new implementation still initializes MSIs first. Only if that
fails, the code tries to enable MSI-X. If that fails too, setup is
continued with intx interrupts.
To not break other chips by this generic code change, there are the
following precautions:
* Interrupt ranges are not enabled at all.
* Only single interrupt mode is enabled for msix cap devices. Thus,
only one interrupt will be setup.
* During the discussion with Tejun we agreed to change the init
sequence from msix-msi-intx to msi-msix-intx. Thus, if a device
offers msi and init does not fail, the msix init code will not be
executed. This is equivalent to current code.
With this, the code only setups single mode msix as a last resort if
msi fails. No interrupt range is enabled at all. Only one interrupt
will be enabled.
tj: comment edits.
Changes of the patch series:
v5:
* updated patch subject that the patch only implements single IRQ
* moved Cavium specific code to a separate patch
* detect Cavium ThunderX device with PCI_CLASS_STORAGE_SATA_AHCI
instead of vendor/dev id
* added more comments to the code
* enable single msix support for all kind of devices (removing strict
check)
* rebased onto update libata/for-4.2 with patch 1, 2 applied
v4:
* removed implementation of ahci_init_intx()
* improved patch descriptions
* rebased onto libata/for-4.2
v3:
* store irq number in struct ahci_host_priv
* change initialization order from msix-msi-intx to msi-msix-intx
* improve comments in ahci_init_msix()
* improve error message in ahci_init_msix()
* do not enable MSI-X if MSI is actively disabled for the device
v2:
* determine irq vector from pci_dev->msi_list
Based on a patch from Sunil Goutham <sgoutham@cavium.com>.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Just six days after this FIXME was added seven years ago, Sam Ravnborg
added the missing feature (37c514e3dfc8 "Add missing init section
definitions"), though it ended up being called __initconst.
Let's use it; better late than never.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Adds support for Ceva sata host controller on Xilinx
Zynq UltraScale+ MPSoC.
Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Freescale introduced QorIQ series SOCs, like ls1021 ls2085, with AHCI
sata support. It complies with the serial ATA 3.0 specification
and the AHCI 1.3 specification.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Yuantian Tang <Yuantian.Tang@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Pull libata fixes from Tejun Heo:
"Two driver fixes. One is for an ahci_mvebu controller config bug and
the other fixes pata_octeon_cf build issue"
* 'for-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
pata_octeon_cf: fix broken build
ata: ahci_mvebu: Fix wrongly set base address for the MBus window setting
|
|
MODULE_DEVICE_TABLE is referring to wrong driver's table and breaks the
build. Fix that.
Cc: stable@vger.kernel.org
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Currently, ahci supports only msi and intx. To also support msix the
handling of the irq number need to be changed. The irq number for msix
devices is taken from msi_list instead of pci_dev. Thus, the irq
number of a device needs to be stored in struct ahci_host_priv now.
This allows the host controller to be activated in a generic way.
This change is only intended for ahci drivers. For that reason the irq
number is stored in struct ahci_host_priv used only by ahci drivers.
Thus, the ABI changes only for ahci_host_activate(), but existing ata
drivers (about 50) are unaffected and keep unchanged. All users of
ahci_host_activate() have been updated.
While touching drivers/ata/libahci.c, doing a small code cleanup in
ahci_port_start().
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
This patch refactors ahci_init_interrupts() and moves msi code to a
separate function. Need the split since we add msix initialization in
a later patch. The initialization for msix will be done after msi but
before intx.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
This patch fix a spelling typo found in libata.xml.
It is because libata.xml is generated from comments
in source, I have to fix it in libata-core.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
According to the Armada 38x datasheet, the window base address
registers value is set in bits [31:4] of the register and corresponds
to the transaction address bits [47:20].
Therefore, the 32bit base address value should be shifted right by
20bits and left by 4bits, resulting in 16 bit shift right.
The bug as not been noticed yet because if the memory available on
the platform is less than 2GB, then the base address is zero.
[gregory.clement@free-electrons.com: add extra-explanation]
Fixes: a3464ed2f14 (ata: ahci_mvebu: new driver for Marvell Armada 380
AHCI interfaces)
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Omri Itach <omrii@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The variable swncq_enabled is bool type. Hence initialize it
with true instead of 1.
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Pretty straightforward driver, using the nice library-ization of the
generic ahci_platform driver.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Commit 5d3abf8ff67f ("libata: Fall back to unqueued READ LOG EXT if
the DMA variant fails") allowed us to fall back to the unqueued READ
LOG variant if the queued version failed. However, if the device did
not support the page at all we would end up looping due to a merge
snafu.
Ensure we only take the fallback path once.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
gcc-5.x warns about a preexisting problem in the hpt36x pata driver:
drivers/ata/pata_hpt366.c: In function 'hpt36x_init_one':
drivers/ata/pata_hpt366.c:376:9: warning: assignment discards 'const' qualifier from pointer target type [-Wdiscarded-array-qualifiers]
Other ata drivers have the same problem, as ata_pci_bmdma_init_one
takes a non-const pointer, and they solve it by using a cast to
turn that pointer into a normal non-const pointer.
I also tried to change the ata core code to make host->private_data
a const pointer, but that quickly got out of hand, as some other
drivers expect it to be writable, so I ended up using the same
hack as the others here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Use syscon/regmap to configure the smc. This allows to avoid using
at91sam9_smc.h and to compile the driver in a multiplatform configuration.
The driver will still not probe until the proper DT bindings are added. That
binding will include an atmel,smc property that is a phandle to the SMC the CF
controller is connected to.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Smatch complains about this potential NULL dereference of "acpi_id".
Fixes: c9802a4be661 ('ata: ahci_xgene: Add AHCI Support for 2nd HW version of APM X-Gene SoC AHCI SATA Host controller.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Pull libata fixes from Tejun Heo:
"Rather big for fixes pull.
- SCC controllers never lived to see the light of the day. Both
libata and ide drivers removed.
- In some configurations, link power management policy changes
sometimes cause delayed spurious PHY events which can develop into
noticeable failures. This has been reported several times over the
years. Gabriele's patches suppress PHY events for a while after
LPM policy changes which should help most of these failures without
causing too much problem for hotplug use cases.
- A few controller specific fixes"
[ Hmm. I don't think removing SSC support is really a "fix", but hey, it
removes a lot of lines of code. Which I like. So ... good riddance ]
* 'for-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: avoton port-disable reset-quirk
ata: select DW_DMAC in case of SATA_DWC
libata: Blacklist queued TRIM on all Samsung 800-series
libata: Ignore spurious PHY event on LPM policy change
libata: Add helper to determine when PHY events should be ignored
ata: ahci_st: fixup layering violations / drvdata errors
Remove celleb-only SCC PATA drivers
|
Linus Torvalds
Alban Bedel
Guillermo A. Amaral
Zhang Rui
Vaishali Thakkar
Randy Dunlap
Axel Lin
Tomer Barletz
Tejun Heo
Florian Fainelli
Viresh Kumar
Martin K. Petersen
Mikulas Patocka
David Milburn
Arne Fitzenreiter
Aleksei Mamlin
Lior Amsalem
Geert Uytterhoeven
Suthikulpanit, Suravee
Thomas Petazzoni
Robert Richter
Robert Richter
Rasmus Villemoes
Suneel Garapati
Tang Yuantian
Aaro Koskinen
Masanari Iida
Nadav Haklai
Shailendra Verma
Brian Norris
Arnd Bergmann
Alexandre Belloni
Dan Carpenter