aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/base (unfollow)
AgeCommit message (Collapse)AuthorFilesLines
2013-10-17dm9000: during init reset phy only for dm9000bNikita Kiryanov1-2/+7
Some of the changes introduced in commit 6741f40 (DM9000B: driver initialization upgrade) break functionality on DM9000A (error message during NFS boot: "dm9000 dm9000.0: eth0: link down") Since the changes were meant to serve only DM9000B, make them dependent on the chip type. Cc: David S. Miller <davem@davemloft.net> Cc: Jingoo Han <jg1.han@samsung.com> Cc: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-11net: smc91x: dont't use SMC_outw for fixing up halfword-aligned dataWill Deacon1-4/+2
SMC_outw invokes an endian-aware I/O accessor, which may change the data endianness before writing to the device. This is not suitable for data transfers where the memory buffer is simply a string of bytes that does not require any byte-swapping. This patches fixes the smc91x SMC_PUSH_DATA macro so that it uses the string I/O accessor for outputting the leading or trailing halfwords on halfword-aligned buffers. Cc: <netdev@vger.kernel.org> Cc: Nicolas Pitre <nico@fluxnic.net> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Will Deacon <will.deacon@arm.com> Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-11farsync: fix info leak in ioctlSalva Peiró1-0/+1
The fst_get_iface() code fails to initialize the two padding bytes of struct sync_serial_settings after the ->loopback member. Add an explicit memset(0) before filling the structure to avoid the info leak. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-11ipv6: Initialize ip6_tnl.hlen in gre tunnel even if no route is foundOussama Ghorbel1-2/+1
The ip6_tnl.hlen (gre and ipv6 headers length) is independent from the outgoing interface, so it would be better to initialize it even when no route is found, otherwise its value will be zero. While I'm not sure if this could happen in real life, but doing that will avoid to call the skb_push function with a zero in ip6gre_header function. Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Oussama Ghorbel <ou.ghorbel@gmail.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-11netem: free skb's in tree on resetstephen hemminger1-0/+16
Netem can leak memory because packets get stored in red-black tree and it is not cleared on reset. Reported by: Сергеев Сергей <adron@yapic.net> Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-11netem: update backlog after dropstephen hemminger1-0/+1
When packet is dropped from rb-tree netem the backlog statistic should also be updated. Reported-by: Сергеев Сергей <adron@yapic.net> Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-11l2tp: must disable bh before calling l2tp_xmit_skb()Eric Dumazet1-0/+4
François Cachereul made a very nice bug report and suspected the bh_lock_sock() / bh_unlok_sock() pair used in l2tp_xmit_skb() from process context was not good. This problem was added by commit 6af88da14ee284aaad6e4326da09a89191ab6165 ("l2tp: Fix locking in l2tp_core.c"). l2tp_eth_dev_xmit() runs from BH context, so we must disable BH from other l2tp_xmit_skb() users. [ 452.060011] BUG: soft lockup - CPU#1 stuck for 23s! [accel-pppd:6662] [ 452.061757] Modules linked in: l2tp_ppp l2tp_netlink l2tp_core pppoe pppox ppp_generic slhc ipv6 ext3 mbcache jbd virtio_balloon xfs exportfs dm_mod virtio_blk ata_generic virtio_net floppy ata_piix libata virtio_pci virtio_ring virtio [last unloaded: scsi_wait_scan] [ 452.064012] CPU 1 [ 452.080015] BUG: soft lockup - CPU#2 stuck for 23s! [accel-pppd:6643] [ 452.080015] CPU 2 [ 452.080015] [ 452.080015] Pid: 6643, comm: accel-pppd Not tainted 3.2.46.mini #1 Bochs Bochs [ 452.080015] RIP: 0010:[<ffffffff81059f6c>] [<ffffffff81059f6c>] do_raw_spin_lock+0x17/0x1f [ 452.080015] RSP: 0018:ffff88007125fc18 EFLAGS: 00000293 [ 452.080015] RAX: 000000000000aba9 RBX: ffffffff811d0703 RCX: 0000000000000000 [ 452.080015] RDX: 00000000000000ab RSI: ffff8800711f6896 RDI: ffff8800745c8110 [ 452.080015] RBP: ffff88007125fc18 R08: 0000000000000020 R09: 0000000000000000 [ 452.080015] R10: 0000000000000000 R11: 0000000000000280 R12: 0000000000000286 [ 452.080015] R13: 0000000000000020 R14: 0000000000000240 R15: 0000000000000000 [ 452.080015] FS: 00007fdc0cc24700(0000) GS:ffff8800b6f00000(0000) knlGS:0000000000000000 [ 452.080015] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 452.080015] CR2: 00007fdb054899b8 CR3: 0000000074404000 CR4: 00000000000006a0 [ 452.080015] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 452.080015] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 [ 452.080015] Process accel-pppd (pid: 6643, threadinfo ffff88007125e000, task ffff8800b27e6dd0) [ 452.080015] Stack: [ 452.080015] ffff88007125fc28 ffffffff81256559 ffff88007125fc98 ffffffffa01b2bd1 [ 452.080015] ffff88007125fc58 000000000000000c 00000000029490d0 0000009c71dbe25e [ 452.080015] 000000000000005c 000000080000000e 0000000000000000 ffff880071170600 [ 452.080015] Call Trace: [ 452.080015] [<ffffffff81256559>] _raw_spin_lock+0xe/0x10 [ 452.080015] [<ffffffffa01b2bd1>] l2tp_xmit_skb+0x189/0x4ac [l2tp_core] [ 452.080015] [<ffffffffa01c2d36>] pppol2tp_sendmsg+0x15e/0x19c [l2tp_ppp] [ 452.080015] [<ffffffff811c7872>] __sock_sendmsg_nosec+0x22/0x24 [ 452.080015] [<ffffffff811c83bd>] sock_sendmsg+0xa1/0xb6 [ 452.080015] [<ffffffff81254e88>] ? __schedule+0x5c1/0x616 [ 452.080015] [<ffffffff8103c7c6>] ? __dequeue_signal+0xb7/0x10c [ 452.080015] [<ffffffff810bbd21>] ? fget_light+0x75/0x89 [ 452.080015] [<ffffffff811c8444>] ? sockfd_lookup_light+0x20/0x56 [ 452.080015] [<ffffffff811c9b34>] sys_sendto+0x10c/0x13b [ 452.080015] [<ffffffff8125cac2>] system_call_fastpath+0x16/0x1b [ 452.080015] Code: 81 48 89 e5 72 0c 31 c0 48 81 ff 45 66 25 81 0f 92 c0 5d c3 55 b8 00 01 00 00 48 89 e5 f0 66 0f c1 07 0f b6 d4 38 d0 74 06 f3 90 <8a> 07 eb f6 5d c3 90 90 55 48 89 e5 9c 58 0f 1f 44 00 00 5d c3 [ 452.080015] Call Trace: [ 452.080015] [<ffffffff81256559>] _raw_spin_lock+0xe/0x10 [ 452.080015] [<ffffffffa01b2bd1>] l2tp_xmit_skb+0x189/0x4ac [l2tp_core] [ 452.080015] [<ffffffffa01c2d36>] pppol2tp_sendmsg+0x15e/0x19c [l2tp_ppp] [ 452.080015] [<ffffffff811c7872>] __sock_sendmsg_nosec+0x22/0x24 [ 452.080015] [<ffffffff811c83bd>] sock_sendmsg+0xa1/0xb6 [ 452.080015] [<ffffffff81254e88>] ? __schedule+0x5c1/0x616 [ 452.080015] [<ffffffff8103c7c6>] ? __dequeue_signal+0xb7/0x10c [ 452.080015] [<ffffffff810bbd21>] ? fget_light+0x75/0x89 [ 452.080015] [<ffffffff811c8444>] ? sockfd_lookup_light+0x20/0x56 [ 452.080015] [<ffffffff811c9b34>] sys_sendto+0x10c/0x13b [ 452.080015] [<ffffffff8125cac2>] system_call_fastpath+0x16/0x1b [ 452.064012] [ 452.064012] Pid: 6662, comm: accel-pppd Not tainted 3.2.46.mini #1 Bochs Bochs [ 452.064012] RIP: 0010:[<ffffffff81059f6e>] [<ffffffff81059f6e>] do_raw_spin_lock+0x19/0x1f [ 452.064012] RSP: 0018:ffff8800b6e83ba0 EFLAGS: 00000297 [ 452.064012] RAX: 000000000000aaa9 RBX: ffff8800b6e83b40 RCX: 0000000000000002 [ 452.064012] RDX: 00000000000000aa RSI: 000000000000000a RDI: ffff8800745c8110 [ 452.064012] RBP: ffff8800b6e83ba0 R08: 000000000000c802 R09: 000000000000001c [ 452.064012] R10: ffff880071096c4e R11: 0000000000000006 R12: ffff8800b6e83b18 [ 452.064012] R13: ffffffff8125d51e R14: ffff8800b6e83ba0 R15: ffff880072a589c0 [ 452.064012] FS: 00007fdc0b81e700(0000) GS:ffff8800b6e80000(0000) knlGS:0000000000000000 [ 452.064012] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 452.064012] CR2: 0000000000625208 CR3: 0000000074404000 CR4: 00000000000006a0 [ 452.064012] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 452.064012] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 [ 452.064012] Process accel-pppd (pid: 6662, threadinfo ffff88007129a000, task ffff8800744f7410) [ 452.064012] Stack: [ 452.064012] ffff8800b6e83bb0 ffffffff81256559 ffff8800b6e83bc0 ffffffff8121c64a [ 452.064012] ffff8800b6e83bf0 ffffffff8121ec7a ffff880072a589c0 ffff880071096c62 [ 452.064012] 0000000000000011 ffffffff81430024 ffff8800b6e83c80 ffffffff8121f276 [ 452.064012] Call Trace: [ 452.064012] <IRQ> [ 452.064012] [<ffffffff81256559>] _raw_spin_lock+0xe/0x10 [ 452.064012] [<ffffffff8121c64a>] spin_lock+0x9/0xb [ 452.064012] [<ffffffff8121ec7a>] udp_queue_rcv_skb+0x186/0x269 [ 452.064012] [<ffffffff8121f276>] __udp4_lib_rcv+0x297/0x4ae [ 452.064012] [<ffffffff8121c178>] ? raw_rcv+0xe9/0xf0 [ 452.064012] [<ffffffff8121f4a7>] udp_rcv+0x1a/0x1c [ 452.064012] [<ffffffff811fe385>] ip_local_deliver_finish+0x12b/0x1a5 [ 452.064012] [<ffffffff811fe54e>] ip_local_deliver+0x53/0x84 [ 452.064012] [<ffffffff811fe1d0>] ip_rcv_finish+0x2bc/0x2f3 [ 452.064012] [<ffffffff811fe78f>] ip_rcv+0x210/0x269 [ 452.064012] [<ffffffff8101911e>] ? kvm_clock_get_cycles+0x9/0xb [ 452.064012] [<ffffffff811d88cd>] __netif_receive_skb+0x3a5/0x3f7 [ 452.064012] [<ffffffff811d8eba>] netif_receive_skb+0x57/0x5e [ 452.064012] [<ffffffff811cf30f>] ? __netdev_alloc_skb+0x1f/0x3b [ 452.064012] [<ffffffffa0049126>] virtnet_poll+0x4ba/0x5a4 [virtio_net] [ 452.064012] [<ffffffff811d9417>] net_rx_action+0x73/0x184 [ 452.064012] [<ffffffffa01b2cc2>] ? l2tp_xmit_skb+0x27a/0x4ac [l2tp_core] [ 452.064012] [<ffffffff810343b9>] __do_softirq+0xc3/0x1a8 [ 452.064012] [<ffffffff81013b56>] ? ack_APIC_irq+0x10/0x12 [ 452.064012] [<ffffffff81256559>] ? _raw_spin_lock+0xe/0x10 [ 452.064012] [<ffffffff8125e0ac>] call_softirq+0x1c/0x26 [ 452.064012] [<ffffffff81003587>] do_softirq+0x45/0x82 [ 452.064012] [<ffffffff81034667>] irq_exit+0x42/0x9c [ 452.064012] [<ffffffff8125e146>] do_IRQ+0x8e/0xa5 [ 452.064012] [<ffffffff8125676e>] common_interrupt+0x6e/0x6e [ 452.064012] <EOI> [ 452.064012] [<ffffffff810b82a1>] ? kfree+0x8a/0xa3 [ 452.064012] [<ffffffffa01b2cc2>] ? l2tp_xmit_skb+0x27a/0x4ac [l2tp_core] [ 452.064012] [<ffffffffa01b2c25>] ? l2tp_xmit_skb+0x1dd/0x4ac [l2tp_core] [ 452.064012] [<ffffffffa01c2d36>] pppol2tp_sendmsg+0x15e/0x19c [l2tp_ppp] [ 452.064012] [<ffffffff811c7872>] __sock_sendmsg_nosec+0x22/0x24 [ 452.064012] [<ffffffff811c83bd>] sock_sendmsg+0xa1/0xb6 [ 452.064012] [<ffffffff81254e88>] ? __schedule+0x5c1/0x616 [ 452.064012] [<ffffffff8103c7c6>] ? __dequeue_signal+0xb7/0x10c [ 452.064012] [<ffffffff810bbd21>] ? fget_light+0x75/0x89 [ 452.064012] [<ffffffff811c8444>] ? sockfd_lookup_light+0x20/0x56 [ 452.064012] [<ffffffff811c9b34>] sys_sendto+0x10c/0x13b [ 452.064012] [<ffffffff8125cac2>] system_call_fastpath+0x16/0x1b [ 452.064012] Code: 89 e5 72 0c 31 c0 48 81 ff 45 66 25 81 0f 92 c0 5d c3 55 b8 00 01 00 00 48 89 e5 f0 66 0f c1 07 0f b6 d4 38 d0 74 06 f3 90 8a 07 <eb> f6 5d c3 90 90 55 48 89 e5 9c 58 0f 1f 44 00 00 5d c3 55 48 [ 452.064012] Call Trace: [ 452.064012] <IRQ> [<ffffffff81256559>] _raw_spin_lock+0xe/0x10 [ 452.064012] [<ffffffff8121c64a>] spin_lock+0x9/0xb [ 452.064012] [<ffffffff8121ec7a>] udp_queue_rcv_skb+0x186/0x269 [ 452.064012] [<ffffffff8121f276>] __udp4_lib_rcv+0x297/0x4ae [ 452.064012] [<ffffffff8121c178>] ? raw_rcv+0xe9/0xf0 [ 452.064012] [<ffffffff8121f4a7>] udp_rcv+0x1a/0x1c [ 452.064012] [<ffffffff811fe385>] ip_local_deliver_finish+0x12b/0x1a5 [ 452.064012] [<ffffffff811fe54e>] ip_local_deliver+0x53/0x84 [ 452.064012] [<ffffffff811fe1d0>] ip_rcv_finish+0x2bc/0x2f3 [ 452.064012] [<ffffffff811fe78f>] ip_rcv+0x210/0x269 [ 452.064012] [<ffffffff8101911e>] ? kvm_clock_get_cycles+0x9/0xb [ 452.064012] [<ffffffff811d88cd>] __netif_receive_skb+0x3a5/0x3f7 [ 452.064012] [<ffffffff811d8eba>] netif_receive_skb+0x57/0x5e [ 452.064012] [<ffffffff811cf30f>] ? __netdev_alloc_skb+0x1f/0x3b [ 452.064012] [<ffffffffa0049126>] virtnet_poll+0x4ba/0x5a4 [virtio_net] [ 452.064012] [<ffffffff811d9417>] net_rx_action+0x73/0x184 [ 452.064012] [<ffffffffa01b2cc2>] ? l2tp_xmit_skb+0x27a/0x4ac [l2tp_core] [ 452.064012] [<ffffffff810343b9>] __do_softirq+0xc3/0x1a8 [ 452.064012] [<ffffffff81013b56>] ? ack_APIC_irq+0x10/0x12 [ 452.064012] [<ffffffff81256559>] ? _raw_spin_lock+0xe/0x10 [ 452.064012] [<ffffffff8125e0ac>] call_softirq+0x1c/0x26 [ 452.064012] [<ffffffff81003587>] do_softirq+0x45/0x82 [ 452.064012] [<ffffffff81034667>] irq_exit+0x42/0x9c [ 452.064012] [<ffffffff8125e146>] do_IRQ+0x8e/0xa5 [ 452.064012] [<ffffffff8125676e>] common_interrupt+0x6e/0x6e [ 452.064012] <EOI> [<ffffffff810b82a1>] ? kfree+0x8a/0xa3 [ 452.064012] [<ffffffffa01b2cc2>] ? l2tp_xmit_skb+0x27a/0x4ac [l2tp_core] [ 452.064012] [<ffffffffa01b2c25>] ? l2tp_xmit_skb+0x1dd/0x4ac [l2tp_core] [ 452.064012] [<ffffffffa01c2d36>] pppol2tp_sendmsg+0x15e/0x19c [l2tp_ppp] [ 452.064012] [<ffffffff811c7872>] __sock_sendmsg_nosec+0x22/0x24 [ 452.064012] [<ffffffff811c83bd>] sock_sendmsg+0xa1/0xb6 [ 452.064012] [<ffffffff81254e88>] ? __schedule+0x5c1/0x616 [ 452.064012] [<ffffffff8103c7c6>] ? __dequeue_signal+0xb7/0x10c [ 452.064012] [<ffffffff810bbd21>] ? fget_light+0x75/0x89 [ 452.064012] [<ffffffff811c8444>] ? sockfd_lookup_light+0x20/0x56 [ 452.064012] [<ffffffff811c9b34>] sys_sendto+0x10c/0x13b [ 452.064012] [<ffffffff8125cac2>] system_call_fastpath+0x16/0x1b Reported-by: François Cachereul <f.cachereul@alphalink.fr> Tested-by: François Cachereul <f.cachereul@alphalink.fr> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: James Chapman <jchapman@katalix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-11net: sh_eth: Correct fix for RX packet errors on R8A7740Simon Horman1-4/+4
Nguyen Hong Ky posted a patch to correct RX packet errors on R8A7740 which was applied as 2c6221e4a5aab417 ("net: sh_eth: Fix RX packets errors on R8A7740"). Unfortunately sh_eth.c contains many similar instances of struct sh_eth_cpu_data and the patch was miss-applied, updating sh7734_data instead of r8a7740_data. This patch corrects this problem by. 1. Reverting the change to sh7734_data and; 2. Applying the change to r8a7740_data. Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-11vti: get rid of nf mark rule in preroutingChristophe Gouault1-3/+11
This patch fixes and improves the use of vti interfaces (while lightly changing the way of configuring them). Currently: - it is necessary to identify and mark inbound IPsec packets destined to each vti interface, via netfilter rules in the mangle table at prerouting hook. - the vti module cannot retrieve the right tunnel in input since commit b9959fd3: vti tunnels all have an i_key, but the tunnel lookup is done with flag TUNNEL_NO_KEY, so there no chance to retrieve them. - the i_key is used by the outbound processing as a mark to lookup for the right SP and SA bundle. This patch uses the o_key to store the vti mark (instead of i_key) and enables: - to avoid the need for previously marking the inbound skbuffs via a netfilter rule. - to properly retrieve the right tunnel in input, only based on the IPsec packet outer addresses. - to properly perform an inbound policy check (using the tunnel o_key as a mark). - to properly perform an outbound SPD and SAD lookup (using the tunnel o_key as a mark). - to keep the current mark of the skbuff. The skbuff mark is neither used nor changed by the vti interface. Only the vti interface o_key is used. SAs have a wildcard mark. SPs have a mark equal to the vti interface o_key. The vti interface must be created as follows (i_key = 0, o_key = mark): ip link add vti1 mode vti local 1.1.1.1 remote 2.2.2.2 okey 1 The SPs attached to vti1 must be created as follows (mark = vti1 o_key): ip xfrm policy add dir out mark 1 tmpl src 1.1.1.1 dst 2.2.2.2 \ proto esp mode tunnel ip xfrm policy add dir in mark 1 tmpl src 2.2.2.2 dst 1.1.1.1 \ proto esp mode tunnel The SAs are created with the default wildcard mark. There is no distinction between global vs. vti SAs. Just their addresses will possibly link them to a vti interface: ip xfrm state add src 1.1.1.1 dst 2.2.2.2 proto esp spi 1000 mode tunnel \ enc "cbc(aes)" "azertyuiopqsdfgh" ip xfrm state add src 2.2.2.2 dst 1.1.1.1 proto esp spi 2000 mode tunnel \ enc "cbc(aes)" "sqbdhgqsdjqjsdfh" To avoid matching "global" (not vti) SPs in vti interfaces, global SPs should no use the default wildcard mark, but explicitly match mark 0. To avoid a double SPD lookup in input and output (in global and vti SPDs), the NOPOLICY and NOXFRM options should be set on the vti interfaces: echo 1 > /proc/sys/net/ipv4/conf/vti1/disable_policy echo 1 > /proc/sys/net/ipv4/conf/vti1/disable_xfrm The outgoing traffic is steered to vti1 by a route via the vti interface: ip route add 192.168.0.0/16 dev vti1 The incoming IPsec traffic is steered to vti1 because its outer addresses match the vti1 tunnel configuration. Signed-off-by: Christophe Gouault <christophe.gouault@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-11bridge: update mdb expiration timer upon reports.Vlad Yasevich1-1/+8
commit 9f00b2e7cf241fa389733d41b615efdaa2cb0f5b bridge: only expire the mdb entry when query is received changed the mdb expiration timer to be armed only when QUERY is received. Howerver, this causes issues in an environment where the multicast server socket comes and goes very fast while a client is trying to send traffic to it. The root cause is a race where a sequence of LEAVE followed by REPORT messages can race against QUERY messages generated in response to LEAVE. The QUERY ends up starting the expiration timer, and that timer can potentially expire after the new REPORT message has been received signaling the new join operation. This leads to a significant drop in multicast traffic and possible complete stall. The solution is to have REPORT messages update the expiration timer on entries that already exist. CC: Cong Wang <xiyou.wangcong@gmail.com> CC: Herbert Xu <herbert@gondor.apana.org.au> CC: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-09can: at91-can: fix device to driver data mapping for platform devicesMarc Kleine-Budde1-2/+2
In commit: 3078cde7 can: at91_can: add dt support device tree support was added to the at91_can driver. In this commit the mapping of device to driver data was mixed up. This results in the sam9x5 parameters being used for the sam9263 and the workaround for the broken mailbox 0 on the sam9263 not being activated. This patch fixes the broken platform_device_id table. Cc: linux-stable <stable@vger.kernel.org> Cc: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2013-10-09can: flexcan: fix mx28 detection by rearanging OF match tableMarc Kleine-Budde1-2/+2
The current implemetation of of_match_device() relies that the of_device_id table in the driver is sorted from most specific to least specific compatible. Without this patch the mx28 is detected as the less specific p1010. This leads to a p1010 specific workaround is activated on the mx28, which is not needed. Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2013-10-09can: flexcan: flexcan_chip_start: fix regression, mark one MB for TX and abort pending TXMarc Kleine-Budde1-2/+8
In patch 0d1862e can: flexcan: fix flexcan_chip_start() on imx6 the loop in flexcan_chip_start() that iterates over all mailboxes after the soft reset of the CAN core was removed. This loop put all mailboxes (even the ones marked as reserved 1...7) into EMPTY/INACTIVE mode. On mailboxes 8...63, this aborts any pending TX messages. After a cold boot there is random garbage in the mailboxes, which leads to spontaneous transmit of CAN frames during first activation. Further if the interface was disabled with a pending message (usually due to an error condition on the CAN bus), this message is retransmitted after enabling the interface again. This patch fixes the regression by: 1) Limiting the maximum number of used mailboxes to 8, 0...7 are used by the RX FIFO, 8 is used by TX. 2) Marking the TX mailbox as EMPTY/INACTIVE, so that any pending TX of that mailbox is aborted. Cc: linux-stable <stable@vger.kernel.org> Cc: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2013-10-09gianfar: Enable eTSEC-20 erratum w/a for P2020 Rev1Claudiu Manoil1-0/+3
Enable workaround for P2020/P2010 erratum eTSEC 20, "Excess delays when transmitting TOE=1 large frames". The impact is that frames lager than 2500-bytes for which TOE (i.e. TCP/IP hw accelerations like Tx csum) is enabled may see excess delay before start of transmission. This erratum was fixed in Rev 2.0. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-09gianfar: Use mpc85xx support for errata detectionClaudiu Manoil1-8/+25
Use the macros and defines from mpc85xx.h to simplify and prevent errors in identifying a mpc85xx based SoC for errata detection. This should help enabling (and identifying) workarounds for various mpc85xx based chips and revisions. For instance, express MPC8548 Rev.2 as: (SVR_SOC_VER(svr) == SVR_8548) && (SVR_REV(svr) == 0x20) instead of: (pvr == 0x80210020 && mod == 0x8030 && rev == 0x0020) Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-09gianfar: Enable eTSEC-A002 erratum w/a for all partsClaudiu Manoil1-6/+4
A002 is still in "no plans to fix" state, and applies to all the current P1/P2 parts as well, so it's resonable to enable its workaround by default, for all the soc's with etsec. The impact of not enabling this workaround for affected parts is that under certain conditons (runt frames or even frames with RX error detected at PHY level) during controller reset, the controller might fail to indicate Rx reset (GRS) completion. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-09net: secure_seq: Fix warning when CONFIG_IPV6 and CONFIG_INET are not selectedFabio Estevam1-0/+2
net_secret() is only used when CONFIG_IPV6 or CONFIG_INET are selected. Building a defconfig with both of these symbols unselected (Using the ARM at91sam9rl_defconfig, for example) leads to the following build warning: $ make at91sam9rl_defconfig # # configuration written to .config # $ make net/core/secure_seq.o scripts/kconfig/conf --silentoldconfig Kconfig CHK include/config/kernel.release CHK include/generated/uapi/linux/version.h CHK include/generated/utsrelease.h make[1]: `include/generated/mach-types.h' is up to date. CALL scripts/checksyscalls.sh CC net/core/secure_seq.o net/core/secure_seq.c:17:13: warning: 'net_secret_init' defined but not used [-Wunused-function] Fix this warning by protecting the definition of net_secret() with these symbols. Reported-by: Olof Johansson <olof@lixom.net> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-08pkt_sched: fq: fix non TCP flows pacingEric Dumazet2-11/+10
Steinar reported FQ pacing was not working for UDP flows. It looks like the initial sk->sk_pacing_rate value of 0 was a wrong choice. We should init it to ~0U (unlimited) Then, TCA_FQ_FLOW_DEFAULT_RATE should be removed because it makes no real sense. The default rate is really unlimited, and we need to avoid a zero divide. Reported-by: Steinar H. Gunderson <sesse@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-08qlcnic: add missing destroy_workqueue() on error path in qlcnic_probe()Wei Yongjun1-1/+4
Add the missing destroy_workqueue() before return from qlcnic_probe() in the error handling case. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-08moxa: fix the error handling in moxart_mac_probe()Wei Yongjun1-6/+16
This patch fix the error handling in moxart_mac_probe(): - return -ENOMEM in some memory alloc fail cases - add missing free_netdev() in the error handling case Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-08net: vlan: fix nlmsg size calculation in vlan_get_size()Marc Kleine-Budde1-1/+1
This patch fixes the calculation of the nlmsg size, by adding the missing nla_total_size(). Cc: Patrick McHardy <kaber@trash.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-08pkt_sched: fq: fix typo for initial_quantumEric Dumazet1-1/+1
TCA_FQ_INITIAL_QUANTUM should set q->initial_quantum Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-08ipv6: Fix the upper MTU limit in GRE tunnelOussama Ghorbel1-2/+1
Unlike ipv4, the struct member hlen holds the length of the GRE and ipv6 headers. This length is also counted in dev->hard_header_len. Perhaps, it's more clean to modify the hlen to count only the GRE header without ipv6 header as the variable name suggest, but the simple way to fix this without regression risk is simply modify the calculation of the limit in ip6gre_tunnel_change_mtu function. Verified in kernel version v3.11. Signed-off-by: Oussama Ghorbel <ou.ghorbel@gmail.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-08xen-netback: transition to CLOSED when removing a VIFDavid Vrabel1-0/+4
If a guest is destroyed without transitioning its frontend to CLOSED, the domain becomes a zombie as netback was not grant unmapping the shared rings. When removing a VIF, transition the backend to CLOSED so the VIF is disconnected if necessary (which will unmap the shared rings etc). This fixes a regression introduced by 279f438e36c0a70b23b86d2090aeec50155034a9 (xen-netback: Don't destroy the netdev until the vif is shut down). Signed-off-by: David Vrabel <david.vrabel@citrix.com> Cc: Ian Campbell <ian.campbell@citrix.com> Cc: Wei Liu <wei.liu2@citrix.com> Cc: Paul Durrant <Paul.Durrant@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Reviewed-by: Paul Durrant <paul.durrant@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-08net/mlx4_en: Fix pages never dma unmapped on rxAmir Vadai1-2/+3
This patch fixes a bug introduced by commit 51151a16 (mlx4: allow order-0 memory allocations in RX path). dma_unmap_page never reached because condition to detect last fragment in page is wrong. offset+frag_stride can't be greater than size, need to make sure no additional frag will fit in page => compare offset + frag_stride + next_frag_size instead. next_frag_size is the same as the current one, since page is shared only with frags of the same size. CC: Eric Dumazet <edumazet@google.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-08net/mlx4_en: Rename name of mlx4_en_rx_alloc membersAmir Vadai2-19/+25
Add page prefix to page related members: @size and @offset into @page_size and @page_offset CC: Eric Dumazet <edumazet@google.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-08net: sh_eth: Fix RX packets errors on R8A7740Nguyen Hong Ky1-0/+4
This patch will fix RX packets errors when receiving big size of data by set bit RNC = 1. RNC - Receive Enable Control 0: Upon completion of reception of one frame, the E-DMAC writes the receive status to the descriptor and clears the RR bit in EDRRR to 0. 1: Upon completion of reception of one frame, the E-DMAC writes (writes back) the receive status to the descriptor. In addition, the E-DMAC reads the next descriptor and prepares for reception of the next frame. In addition, for get more stable when receiving packets, I set maximum size for the transmit/receive FIFO and inserts padding in receive data. Signed-off-by: Nguyen Hong Ky <nh-ky@jinso.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-08l2tp: Fix build warning with ipv6 disabled.David S. Miller1-5/+8
net/l2tp/l2tp_core.c: In function ‘l2tp_verify_udp_checksum’: net/l2tp/l2tp_core.c:499:22: warning: unused variable ‘tunnel’ [-Wunused-variable] Create a helper "l2tp_tunnel()" to facilitate this, and as a side effect get rid of a bunch of unnecessary void pointer casts. Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-08tun: don't look at current when non-blockingMichael S. Tsirkin1-3/+5
We play with a wait queue even if socket is non blocking. This is an obvious waste. Besides, it will prevent calling the non blocking variant when current is not valid. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-08mrf24j40: Use level-triggered interruptsAlan Ott1-1/+1
The mrf24j40 generates level interrupts. There are rare cases where it appears that the interrupt line never gets de-asserted between interrupts, causing interrupts to be lost, and causing a hung device from the driver's perspective. Switching the driver to interpret these interrupts as level-triggered fixes this issue. Signed-off-by: Alan Ott <alan@signal11.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-08mrf24j40: Use threaded IRQ handlerAlan Ott1-20/+7
Eliminate all the workqueue and interrupt enable/disable. Signed-off-by: Alan Ott <alan@signal11.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-08mrf24j40: Move INIT_COMPLETION() to before packet transmissionAlan Ott1-2/+2
This avoids a race condition where complete(tx_complete) could be called before tx_complete is initialized. Signed-off-by: Alan Ott <alan@signal11.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-086lowpan: Sync default hardware address of lowpan links to their wpanAlan Ott1-0/+3
When a lowpan link to a wpan device is created, set the hardware address of the lowpan link to that of the wpan device. Signed-off-by: Alan Ott <alan@signal11.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-086lowpan: Only make 6lowpan links to IEEE802154 devicesAlan Ott1-0/+2
Refuse to create 6lowpan links if the actual hardware interface is of any type other than ARPHRD_IEEE802154. Signed-off-by: Alan Ott <alan@signal11.us> Suggested-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-08xfrm: check for a vaild skb in xfrm_policy_queue_processSteffen Klassert1-0/+4
We might dreference a NULL pointer if the hold_queue is empty, so add a check to avoid this. Bug was introduced with git commit a0073fe18 ("xfrm: Add a state resolution packet queue") Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2013-10-08xfrm: Add refcount handling to queued policiesSteffen Klassert1-7/+17
We need to ensure that policies can't go away as long as the hold timer is armed, so take a refcont when we arm the timer and drop one if we delete it. Bug was introduced with git commit a0073fe18 ("xfrm: Add a state resolution packet queue") Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2013-10-07net: Update the sysctl permissions handler to test effective uid/gidEric W. Biederman1-2/+2
On Tue, 20 Aug 2013 11:40:04 -0500 Eric Sandeen <sandeen@redhat.com> wrote: > This was brought up in a Red Hat bug (which may be marked private, I'm sorry): > > Bug 987055 - open O_WRONLY succeeds on some root owned files in /proc for process running with unprivileged EUID > > "On RHEL7 some of the files in /proc can be opened for writing by an unprivileged EUID." > > The flaw existed upstream as well last I checked. > > This commit in kernel v3.8 caused the regression: > > commit cff109768b2d9c03095848f4cd4b0754117262aa > Author: Eric W. Biederman <ebiederm@xmission.com> > Date: Fri Nov 16 03:03:01 2012 +0000 > > net: Update the per network namespace sysctls to be available to the network namespace owner > > - Allow anyone with CAP_NET_ADMIN rights in the user namespace of the > the netowrk namespace to change sysctls. > - Allow anyone the uid of the user namespace root the same > permissions over the network namespace sysctls as the global root. > - Allow anyone with gid of the user namespace root group the same > permissions over the network namespace sysctl as the global root group. > > Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> > Signed-off-by: David S. Miller <davem@davemloft.net> > > because it changed /sys/net's special permission handler to test current_uid, not > current_euid; same for current_gid/current_egid. > > So in this case, root cannot drop privs via set[ug]id, and retains all privs > in this codepath. Modify the code to use current_euid(), and in_egroup_p, as in done in fs/proc/proc_sysctl.c:test_perm() Cc: stable@vger.kernel.org Reviewed-by: Eric Sandeen <sandeen@redhat.com> Reported-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-07can: dev: fix nlmsg size calculation in can_get_size()Marc Kleine-Budde1-5/+5
This patch fixes the calculation of the nlmsg size, by adding the missing nla_total_size(). Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-07ipv4: fix ineffective source address selectionJiri Benc1-1/+1
When sending out multicast messages, the source address in inet->mc_addr is ignored and rewritten by an autoselected one. This is caused by a typo in commit 813b3b5db831 ("ipv4: Use caller's on-stack flowi as-is in output route lookups"). Signed-off-by: Jiri Benc <jbenc@redhat.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-07net/ethernet: cpsw: DT read bool dual_emacMarkus Pargmann1-2/+2
Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Acked-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-07net: ethernet: cpsw: Search childs for slave nodesMarkus Pargmann1-1/+5
The current implementation searches the whole DT for nodes named "slave". This patch changes it to search only child nodes for slaves. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Acked-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-07net: fix unsafe set_memory_rw from softirqAlexei Starovoitov8-18/+36
on x86 system with net.core.bpf_jit_enable = 1 sudo tcpdump -i eth1 'tcp port 22' causes the warning: [ 56.766097] Possible unsafe locking scenario: [ 56.766097] [ 56.780146] CPU0 [ 56.786807] ---- [ 56.793188] lock(&(&vb->lock)->rlock); [ 56.799593] <Interrupt> [ 56.805889] lock(&(&vb->lock)->rlock); [ 56.812266] [ 56.812266] *** DEADLOCK *** [ 56.812266] [ 56.830670] 1 lock held by ksoftirqd/1/13: [ 56.836838] #0: (rcu_read_lock){.+.+..}, at: [<ffffffff8118f44c>] vm_unmap_aliases+0x8c/0x380 [ 56.849757] [ 56.849757] stack backtrace: [ 56.862194] CPU: 1 PID: 13 Comm: ksoftirqd/1 Not tainted 3.12.0-rc3+ #45 [ 56.868721] Hardware name: System manufacturer System Product Name/P8Z77 WS, BIOS 3007 07/26/2012 [ 56.882004] ffffffff821944c0 ffff88080bbdb8c8 ffffffff8175a145 0000000000000007 [ 56.895630] ffff88080bbd5f40 ffff88080bbdb928 ffffffff81755b14 0000000000000001 [ 56.909313] ffff880800000001 ffff880800000000 ffffffff8101178f 0000000000000001 [ 56.923006] Call Trace: [ 56.929532] [<ffffffff8175a145>] dump_stack+0x55/0x76 [ 56.936067] [<ffffffff81755b14>] print_usage_bug+0x1f7/0x208 [ 56.942445] [<ffffffff8101178f>] ? save_stack_trace+0x2f/0x50 [ 56.948932] [<ffffffff810cc0a0>] ? check_usage_backwards+0x150/0x150 [ 56.955470] [<ffffffff810ccb52>] mark_lock+0x282/0x2c0 [ 56.961945] [<ffffffff810ccfed>] __lock_acquire+0x45d/0x1d50 [ 56.968474] [<ffffffff810cce6e>] ? __lock_acquire+0x2de/0x1d50 [ 56.975140] [<ffffffff81393bf5>] ? cpumask_next_and+0x55/0x90 [ 56.981942] [<ffffffff810cef72>] lock_acquire+0x92/0x1d0 [ 56.988745] [<ffffffff8118f52a>] ? vm_unmap_aliases+0x16a/0x380 [ 56.995619] [<ffffffff817628f1>] _raw_spin_lock+0x41/0x50 [ 57.002493] [<ffffffff8118f52a>] ? vm_unmap_aliases+0x16a/0x380 [ 57.009447] [<ffffffff8118f52a>] vm_unmap_aliases+0x16a/0x380 [ 57.016477] [<ffffffff8118f44c>] ? vm_unmap_aliases+0x8c/0x380 [ 57.023607] [<ffffffff810436b0>] change_page_attr_set_clr+0xc0/0x460 [ 57.030818] [<ffffffff810cfb8d>] ? trace_hardirqs_on+0xd/0x10 [ 57.037896] [<ffffffff811a8330>] ? kmem_cache_free+0xb0/0x2b0 [ 57.044789] [<ffffffff811b59c3>] ? free_object_rcu+0x93/0xa0 [ 57.051720] [<ffffffff81043d9f>] set_memory_rw+0x2f/0x40 [ 57.058727] [<ffffffff8104e17c>] bpf_jit_free+0x2c/0x40 [ 57.065577] [<ffffffff81642cba>] sk_filter_release_rcu+0x1a/0x30 [ 57.072338] [<ffffffff811108e2>] rcu_process_callbacks+0x202/0x7c0 [ 57.078962] [<ffffffff81057f17>] __do_softirq+0xf7/0x3f0 [ 57.085373] [<ffffffff81058245>] run_ksoftirqd+0x35/0x70 cannot reuse jited filter memory, since it's readonly, so use original bpf insns memory to hold work_struct defer kfree of sk_filter until jit completed freeing tested on x86_64 and i386 Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-07sfc: Only bind to EF10 functions with the LinkCtrl and Trusted flagsBen Hutchings1-1/+17
Although we do not yet enable multiple PFs per port, it is possible that a board will be reconfigured to enable them while the driver has not yet been updated to fully support this. The most obvious problem is that multiple functions may try to set conflicting link settings. But we will also run into trouble if the firmware doesn't consider us fully trusted. So, abort probing unless both the LinkCtrl and Trusted flags are set for this function. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
2013-10-07iwlwifi: pcie: fix merge damageJohannes Berg1-4/+4
The merge b35c8097 seems to have lost commit eabc4ac5d, put the code back. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-07ath9k: fix tx queue scheduling after channel changesFelix Fietkau1-12/+11
Otherwise, if queues are full during a scan, tx scheduling does not resume after switching back to the home channel. Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-07ipv6: Allow the MTU of ipip6 tunnel to be set below 1280Oussama Ghorbel1-2/+10
The (inner) MTU of a ipip6 (IPv4-in-IPv6) tunnel cannot be set below 1280, which is the minimum MTU in IPv6. However, there should be no IPv6 on the tunnel interface at all, so the IPv6 rules should not apply. More info at https://bugzilla.kernel.org/show_bug.cgi?id=15530 This patch allows to check the minimum MTU for ipv6 tunnel according to these rules: -In case the tunnel is configured with ipip6 mode the minimum MTU is 68. -In case the tunnel is configured with ip6ip6 or any mode the minimum MTU is 1280. Signed-off-by: Oussama Ghorbel <ou.ghorbel@gmail.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-07netif_set_xps_queue: make cpu mask constMichael S. Tsirkin2-3/+5
virtio wants to pass in cpumask_of(cpu), make parameter const to avoid build warnings. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-04sfc: Add PM and RXDP drop counters to ethtool statsEdward Cree2-0/+47
Recognise the new Packet Memory and RX Data Path counters. The following counters are added: rx_pm_{trunc,discard}_bb_overflow - burst buffer overflowed. This should not occur if BB correctly configured. rx_pm_{trunc,discard}_vfifo_full - not enough space in packet memory. May indicate RX performance problems. rx_pm_{trunc,discard}_qbb - dropped by 802.1Qbb early discard mechanism. Since Qbb is not supported at present, this should not occur. rx_pm_discard_mapping - 802.1p priority configured to be dropped. This should not occur in normal operation. rx_dp_q_disabled_packets - packet was to be delivered to a queue but queue is disabled. May indicate misconfiguration by the driver. rx_dp_di_dropped_packets - parser-dispatcher indicated that a packet should be dropped. rx_dp_streaming_packets - packet was sent to the RXDP streaming bus, ie. a filter directed the packet to the MCPU. rx_dp_emerg_{fetch,wait} - RX datapath had to wait for descriptors to be loaded. Indicates performance problems but not drops. These are only provided if the MC firmware has the PM_AND_RXDP_COUNTERS capability. Otherwise, mask them out. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
2013-10-04sfc: Add definitions for new stats counters and capability flagMatthew Slattery1-2/+54
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
2013-10-04sfc: Refactor EF10 stat mask code to allow for more conditional statsEdward Cree1-21/+28
Previously, efx_ef10_stat_mask returned a static const unsigned long[], which meant that each possible mask had to be declared statically with STAT_MASK_BITMAP. Since adding a condition would double the size of the decision tree, we now create the bitmask dynamically. To do this, we have two functions efx_ef10_raw_stat_mask, which returns a u64, and efx_ef10_get_stat_mask, which fills in an unsigned long * argument. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.