| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull x86 pti updates from Thomas Gleixner:
"This contains:
- a PTI bugfix to avoid setting reserved CR3 bits when PCID is
disabled. This seems to cause issues on a virtual machine at least
and is incorrect according to the AMD manual.
- a PTI bugfix which disables the perf BTS facility if PTI is
enabled. The BTS AUX buffer is not globally visible and causes the
CPU to fault when the mapping disappears on switching CR3 to user
space. A full fix which restores BTS on PTI is non trivial and will
be worked on.
- PTI bugfixes for EFI and trusted boot which make sure that the user
space visible page table entries have the NX bit cleared
- removal of dead code in the PTI pagetable setup functions
- add PTI documentation
- add a selftest for vsyscall to verify that the kernel actually
implements what it advertises.
- a sysfs interface to expose vulnerability and mitigation
information so there is a coherent way for users to retrieve the
status.
- the initial spectre_v2 mitigations, aka retpoline:
+ The necessary ASM thunk and compiler support
+ The ASM variants of retpoline and the conversion of affected ASM
code
+ Make LFENCE serializing on AMD so it can be used as speculation
trap
+ The RSB fill after vmexit
- initial objtool support for retpoline
As I said in the status mail this is the most of the set of patches
which should go into 4.15 except two straight forward patches still on
hold:
- the retpoline add on of LFENCE which waits for ACKs
- the RSB fill after context switch
Both should be ready to go early next week and with that we'll have
covered the major holes of spectre_v2 and go back to normality"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
x86,perf: Disable intel_bts when PTI
security/Kconfig: Correct the Documentation reference for PTI
x86/pti: Fix !PCID and sanitize defines
selftests/x86: Add test_vsyscall
x86/retpoline: Fill return stack buffer on vmexit
x86/retpoline/irq32: Convert assembler indirect jumps
x86/retpoline/checksum32: Convert assembler indirect jumps
x86/retpoline/xen: Convert Xen hypercall indirect jumps
x86/retpoline/hyperv: Convert assembler indirect jumps
x86/retpoline/ftrace: Convert ftrace assembler indirect jumps
x86/retpoline/entry: Convert entry assembler indirect jumps
x86/retpoline/crypto: Convert crypto assembler indirect jumps
x86/spectre: Add boot time option to select Spectre v2 mitigation
x86/retpoline: Add initial retpoline support
objtool: Allow alternatives to be ignored
objtool: Detect jumps to retpoline thunks
x86/pti: Make unpoison of pgd for trusted boot work for real
x86/alternatives: Fix optimize_nops() checking
sysfs/cpu: Fix typos in vulnerability documentation
x86/cpu/AMD: Use LFENCE_RDTSC in preference to MFENCE_RDTSC
...
|
|
As the meltdown/spectre problem affects several CPU architectures, it makes
sense to have common way to express whether a system is affected by a
particular vulnerability or not. If affected the way to express the
mitigation should be common as well.
Create /sys/devices/system/cpu/vulnerabilities folder and files for
meltdown, spectre_v1 and spectre_v2.
Allow architectures to override the show function.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Linus Torvalds <torvalds@linuxfoundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lkml.kernel.org/r/20180107214913.096657732@linutronix.de
|
|
Pull driver core fixes from Greg KH:
"Here are two driver core fixes for 4.15-rc6, resolving some reported
issues.
The first is a cacheinfo fix for DT based systems to resolve a
reported issue that has been around for a while, and the other is to
resolve a regression in the kobject uevent code that showed up in
4.15-rc1.
Both have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kobject: fix suppressing modalias in uevents delivered over netlink
drivers: base: cacheinfo: fix cache type for non-architected system cache
|
|
Commit dfea747d2aba ("drivers: base: cacheinfo: support DT overrides for
cache properties") doesn't initialise the cache type if it's present
only in DT and the architecture is not aware of it. They are unified
system level cache which are generally transparent.
This patch check if the cache type is set to NOCACHE but the DT node
indicates that it's unified cache and sets the cache type accordingly.
Fixes: dfea747d2aba ("drivers: base: cacheinfo: support DT overrides for cache properties")
Reported-and-tested-by: Tan Xiaojun <tanxiaojun@huawei.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Middle-layer code doing suspend-time optimizations for devices with
the DPM_FLAG_SMART_SUSPEND flag set (currently, the PCI bus type and
the ACPI PM domain) needs to make the core skip ->thaw_early and
->thaw callbacks for those devices in some cases and it sets the
power.direct_complete flag for them for this purpose.
However, it turns out that setting power.direct_complete outside of
the PM core is a bad idea as it triggers an excess invocation of
pm_runtime_enable() in device_resume().
For this reason, provide a helper to clear power.is_late_suspended
and power.is_suspended to be invoked by the middle-layer code in
question instead of setting power.direct_complete and make that code
call the new helper.
Fixes: c4b65157aeef (PCI / PM: Take SMART_SUSPEND driver flag into account)
Fixes: 05087360fd7a (ACPI / PM: Take SMART_SUSPEND driver flag into account)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Pull power management fix from Rafael Wysocki:
"This fixes an issue in the device runtime PM framework that prevents
customer devices from resuming if runtime PM is disabled for one or
more of their supplier devices (as reflected by device links between
those devices)"
* tag 'pm-4.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / runtime: Fix handling of suppliers with disabled runtime PM
|
|
Prevent rpm_get_suppliers() from returning an error code if runtime
PM is disabled for one or more of the supplier devices it wants to
runtime-resume, so as to make runtime PM work for devices with links
to suppliers that don't use runtime PM (such links may be created
during device enumeration even before it is known whether or not
runtime PM will be enabled for the devices in question, for example).
Fixes: 21d5c57b3726 (PM / runtime: Use device links)
Reported-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Tested-by: Adrian Hunter <adrian.hunter@intel.com>
|
|
The help for FIRMWARE_IN_KERNEL still references the firmware_install
command that was recently removed by commit 5620a0d1aacd ("firmware:
delete in-kernel firmware").
Clean up the message to direct the user to their distribution's
linux-firmware package, and remove any reference to firmware being
included in the kernel source tree.
Fixes: 5620a0d1aacd ("firmware: delete in-kernel firmware").
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: stable <stable@vger.kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The isa_driver structure for an isa_bus device is stored in the device
platform_data member of the respective device structure. This
platform_data member may be reset to NULL if isa_driver match callback
for the device fails, indicating a device unsupported by the ISA driver.
This patch fixes a possible NULL pointer dereference if one of the
isa_driver callbacks to attempted for an unsupported device. This error
should not occur in practice since ISA devices are typically manually
configured and loaded by the users, but we may as well prevent this
error from popping up for the 0day testers.
Fixes: a5117ba7da37 ("[PATCH] Driver model: add ISA bus")
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With all callbacks converted, and the timer callback prototype
switched over, the TIMER_FUNC_TYPE cast is no longer needed,
so remove it. Conversion was done with the following scripts:
perl -pi -e 's|\(TIMER_FUNC_TYPE\)||g' \
$(git grep TIMER_FUNC_TYPE | cut -d: -f1 | sort -u)
perl -pi -e 's|\(TIMER_DATA_TYPE\)||g' \
$(git grep TIMER_DATA_TYPE | cut -d: -f1 | sort -u)
The now unused macros are also dropped from include/linux/timer.h.
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
Pull two power management fixes from Rafael Wysocki:
"This is the change making /proc/cpuinfo on x86 report current CPU
frequency in "cpu MHz" again in all cases and an additional one
dealing with an overzealous check in one of the helper routines in the
runtime PM framework"
* tag 'pm-fixes-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / runtime: Drop children check from __pm_runtime_set_status()
x86 / CPU: Always show current CPU frequency in /proc/cpuinfo
|
|
The check for "active" children in __pm_runtime_set_status(), when
trying to set the parent device status to "suspended", doesn't
really make sense, because in fact it is not invalid to set the
status of a device with runtime PM disabled to "suspended" in any
case. It is invalid to enable runtime PM for a device with its
status set to "suspended" while its child_count reference counter
is nonzero, but the check in __pm_runtime_set_status() doesn't
really cover that situation.
For this reason, drop the children check from __pm_runtime_set_status()
and add a check against child_count reference counters of "suspended"
devices to pm_runtime_enable().
Fixes: a8636c89648a (PM / Runtime: Don't allow to suspend a device with an active child)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
|
|
Pull driver core updates from Greg KH:
"Here is the set of driver core / debugfs patches for 4.15-rc1.
Not many here, mostly all are debugfs fixes to resolve some
long-reported problems with files going away with references to them
in userspace. There's also some SPDX cleanups for the debugfs code, as
well as a few other minor driver core changes for issues reported by
people.
All of these have been in linux-next for a week or more with no
reported issues"
* tag 'driver-core-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: Fix device link deferred probe
debugfs: Remove redundant license text
debugfs: add SPDX identifiers to all debugfs files
debugfs: defer debugfs_fsdata allocation to first usage
debugfs: call debugfs_real_fops() only after debugfs_file_get()
debugfs: purge obsolete SRCU based removal protection
IB/hfi1: convert to debugfs_file_get() and -put()
debugfs: convert to debugfs_file_get() and -put()
debugfs: debugfs_real_fops(): drop __must_hold sparse annotation
debugfs: implement per-file removal protection
debugfs: add support for more elaborate ->d_fsdata
driver core: Move device_links_purge() after bus_remove_device()
arch_topology: Fix section miss match warning due to free_raw_capacity()
driver-core: pr_err() strings should end with newlines
|
|
Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild changes and a tree wide
fix in the binding documentation.
Summary:
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing
memory leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node.
The prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to
dtb compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage
Technology, shimafuji, Tecon Microprocessor Technologies, DH
electronics GmbH, Opal Kelly, and Next Thing"
* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: usb: add #phy-cells to usb-nop-xceiv
dt-bindings: Remove leading zeros from bindings notation
kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
.gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
.gitignore: sort normal pattern rules alphabetically
dt-bindings: add vendor prefix for Next Thing Co.
scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
of: dynamic: fix memory leak related to properties of __of_node_dup
of: overlay: make pr_err() string unique
of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
of: overlay: remove unneeded check for NULL kbasename()
of: overlay: remove a dependency on device node full_name
of: overlay: simplify applying symbols from an overlay
of: overlay: avoid race condition between applying multiple overlays
of: overlay: loosen overly strict phandle clash check
of: overlay: expand check of whether overlay changeset can be removed
of: overlay: detect cases where device tree may become corrupt
of: overlay: minor restructuring
...
|
|
Pull dma-mapping updates from Christoph Hellwig:
- turn dma_cache_sync into a dma_map_ops instance and remove
implementation that purely are dead because the architecture doesn't
support noncoherent allocations
- add a flag for busses that need DMA configuration (Robin Murphy)
* tag 'dma-mapping-4.15' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: turn dma_cache_sync into a dma_map_ops method
sh: make dma_cache_sync a no-op
xtensa: make dma_cache_sync a no-op
unicore32: make dma_cache_sync a no-op
powerpc: make dma_cache_sync a no-op
mn10300: make dma_cache_sync a no-op
microblaze: make dma_cache_sync a no-op
ia64: make dma_cache_sync a no-op
frv: make dma_cache_sync a no-op
x86: make dma_cache_sync a no-op
floppy: consolidate the dummy fd_cacheflush definition
drivers: flag buses which demand DMA configuration
|
|
Pull device properties framework updates from Rafael Wysocki:
"These make the fwnode_handle_get() function return a pointer to the
target fwnode object, which reflects the of_node_get() behavior, and
add a macro for iterating over graph endpoints (Sakari Ailus)"
* tag 'devprop-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
device property: Add a macro for interating over graph endpoints
device property: Make fwnode_handle_get() return the fwnode
|
|
Pull power management updates from Rafael Wysocki:
"There are no real big ticket items here this time.
The most noticeable change is probably the relocation of the OPP
(Operating Performance Points) framework to its own directory under
drivers/ as it has grown big enough for that. Also Viresh is now going
to maintain it and send pull requests for it to me, so you will see
this change in the git history going forward (but still not right
now).
Another noticeable set of changes is the modifications of the PM core,
the PCI subsystem and the ACPI PM domain to allow of more integration
between system-wide suspend/resume and runtime PM. For now it's just a
way to avoid resuming devices from runtime suspend unnecessarily
during system suspend (if the driver sets a flag to indicate its
readiness for that) and in the works is an analogous mechanism to
allow devices to stay suspended after system resume.
In addition to that, we have some changes related to supporting
frequency-invariant CPU utilization metrics in the scheduler and in
the schedutil cpufreq governor on ARM and changes to add support for
device performance states to the generic power domains (genpd)
framework.
The rest is mostly fixes and cleanups of various sorts.
Specifics:
- Relocate the OPP (Operating Performance Points) framework to its
own directory under drivers/ and add support for power domain
performance states to it (Viresh Kumar).
- Modify the PM core, the PCI bus type and the ACPI PM domain to
support power management driver flags allowing device drivers to
specify their capabilities and preferences regarding the handling
of devices with enabled runtime PM during system suspend/resume and
clean up that code somewhat (Rafael Wysocki, Ulf Hansson).
- Add frequency-invariant accounting support to the task scheduler on
ARM and ARM64 (Dietmar Eggemann).
- Fix PM QoS device resume latency framework to prevent "no
restriction" requests from overriding requests with specific
requirements and drop the confusing PM_QOS_FLAG_REMOTE_WAKEUP
device PM QoS flag (Rafael Wysocki).
- Drop legacy class suspend/resume operations from the PM core and
drop legacy bus type suspend and resume callbacks from ARM/locomo
(Rafael Wysocki).
- Add min/max frequency support to devfreq and clean it up somewhat
(Chanwoo Choi).
- Rework wakeup support in the generic power domains (genpd)
framework and update some of its users accordingly (Geert
Uytterhoeven).
- Convert timers in the PM core to use timer_setup() (Kees Cook).
- Add support for exposing the SLP_S0 (Low Power S0 Idle) residency
counter based on the LPIT ACPI table on Intel platforms (Srinivas
Pandruvada).
- Add per-CPU PM QoS resume latency support to the ladder cpuidle
governor (Ramesh Thomas).
- Fix a deadlock between the wakeup notify handler and the notifier
removal in the ACPI core (Ville Syrjälä).
- Fix a cpufreq schedutil governor issue causing it to use stale
cached frequency values sometimes (Viresh Kumar).
- Fix an issue in the system suspend core support code causing wakeup
events detection to fail in some cases (Rajat Jain).
- Fix the generic power domains (genpd) framework to prevent the PM
core from using the direct-complete optimization with it as that is
guaranteed to fail (Ulf Hansson).
- Fix a minor issue in the cpuidle core and clean it up a bit (Gaurav
Jindal, Nicholas Piggin).
- Fix and clean up the intel_idle and ARM cpuidle drivers (Jason
Baron, Len Brown, Leo Yan).
- Fix a couple of minor issues in the OPP framework and clean it up
(Arvind Yadav, Fabio Estevam, Sudeep Holla, Tobias Jordan).
- Fix and clean up some cpufreq drivers and fix a minor issue in the
cpufreq statistics code (Arvind Yadav, Bhumika Goyal, Fabio
Estevam, Gautham Shenoy, Gustavo Silva, Marek Szyprowski, Masahiro
Yamada, Robert Jarzmik, Zumeng Chen).
- Fix minor issues in the system suspend and hibernation core, in
power management documentation and in the AVS (Adaptive Voltage
Scaling) framework (Helge Deller, Himanshu Jha, Joe Perches, Rafael
Wysocki).
- Fix some issues in the cpupower utility and document that Shuah
Khan is going to maintain it going forward (Prarit Bhargava, Shuah
Khan)"
* tag 'pm-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (88 commits)
tools/power/cpupower: add libcpupower.so.0.0.1 to .gitignore
tools/power/cpupower: Add 64 bit library detection
intel_idle: Graceful probe failure when MWAIT is disabled
cpufreq: schedutil: Reset cached_raw_freq when not in sync with next_freq
freezer: Fix typo in freezable_schedule_timeout() comment
PM / s2idle: Clear the events_check_enabled flag
cpufreq: stats: Handle the case when trans_table goes beyond PAGE_SIZE
cpufreq: arm_big_little: make cpufreq_arm_bL_ops structures const
cpufreq: arm_big_little: make function arguments and structure pointer const
cpuidle: Avoid assignment in if () argument
cpuidle: Clean up cpuidle_enable_device() error handling a bit
ACPI / PM: Fix acpi_pm_notifier_lock vs flush_workqueue() deadlock
PM / Domains: Fix genpd to deal with drivers returning 1 from ->prepare()
cpuidle: ladder: Add per CPU PM QoS resume latency support
PM / QoS: Fix device resume latency framework
PM / domains: Rework governor code to be more consistent
PM / Domains: Remove gpd_dev_ops.active_wakeup() callback
soc: rockchip: power-domain: Use GENPD_FLAG_ACTIVE_WAKEUP
soc: mediatek: Use GENPD_FLAG_ACTIVE_WAKEUP
ARM: shmobile: pm-rmobile: Use GENPD_FLAG_ACTIVE_WAKEUP
...
|
|
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
|
|
Pull scheduler updates from Ingo Molnar:
"The main updates in this cycle were:
- Group balancing enhancements and cleanups (Brendan Jackman)
- Move CPU isolation related functionality into its separate
kernel/sched/isolation.c file, with related 'housekeeping_*()'
namespace and nomenclature et al. (Frederic Weisbecker)
- Improve the interactive/cpu-intense fairness calculation (Josef
Bacik)
- Improve the PELT code and related cleanups (Peter Zijlstra)
- Improve the logic of pick_next_task_fair() (Uladzislau Rezki)
- Improve the RT IPI based balancing logic (Steven Rostedt)
- Various micro-optimizations:
- better !CONFIG_SCHED_DEBUG optimizations (Patrick Bellasi)
- better idle loop (Cheng Jian)
- ... plus misc fixes, cleanups and updates"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (54 commits)
sched/core: Optimize sched_feat() for !CONFIG_SCHED_DEBUG builds
sched/sysctl: Fix attributes of some extern declarations
sched/isolation: Document isolcpus= boot parameter flags, mark it deprecated
sched/isolation: Add basic isolcpus flags
sched/isolation: Move isolcpus= handling to the housekeeping code
sched/isolation: Handle the nohz_full= parameter
sched/isolation: Introduce housekeeping flags
sched/isolation: Split out new CONFIG_CPU_ISOLATION=y config from CONFIG_NO_HZ_FULL
sched/isolation: Rename is_housekeeping_cpu() to housekeeping_cpu()
sched/isolation: Use its own static key
sched/isolation: Make the housekeeping cpumask private
sched/isolation: Provide a dynamic off-case to housekeeping_any_cpu()
sched/isolation, watchdog: Use housekeeping_cpumask() instead of ad-hoc version
sched/isolation: Move housekeeping related code to its own file
sched/idle: Micro-optimize the idle loop
sched/isolcpus: Fix "isolcpus=" boot parameter handling when !CONFIG_CPUMASK_OFFSTACK
x86/tsc: Append the 'tsc=' description for the 'tsc=unstable' boot parameter
sched/rt: Simplify the IPI based RT balancing logic
block/ioprio: Use a helper to check for RT prio
sched/rt: Add a helper to test for a RT task
...
|
|
Pull core locking updates from Ingo Molnar:
"The main changes in this cycle are:
- Another attempt at enabling cross-release lockdep dependency
tracking (automatically part of CONFIG_PROVE_LOCKING=y), this time
with better performance and fewer false positives. (Byungchul Park)
- Introduce lockdep_assert_irqs_enabled()/disabled() and convert
open-coded equivalents to lockdep variants. (Frederic Weisbecker)
- Add down_read_killable() and use it in the VFS's iterate_dir()
method. (Kirill Tkhai)
- Convert remaining uses of ACCESS_ONCE() to
READ_ONCE()/WRITE_ONCE(). Most of the conversion was Coccinelle
driven. (Mark Rutland, Paul E. McKenney)
- Get rid of lockless_dereference(), by strengthening Alpha atomics,
strengthening READ_ONCE() with smp_read_barrier_depends() and thus
being able to convert users of lockless_dereference() to
READ_ONCE(). (Will Deacon)
- Various micro-optimizations:
- better PV qspinlocks (Waiman Long),
- better x86 barriers (Michael S. Tsirkin)
- better x86 refcounts (Kees Cook)
- ... plus other fixes and enhancements. (Borislav Petkov, Juergen
Gross, Miguel Bernal Marin)"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
locking/x86: Use LOCK ADD for smp_mb() instead of MFENCE
rcu: Use lockdep to assert IRQs are disabled/enabled
netpoll: Use lockdep to assert IRQs are disabled/enabled
timers/posix-cpu-timers: Use lockdep to assert IRQs are disabled/enabled
sched/clock, sched/cputime: Use lockdep to assert IRQs are disabled/enabled
irq_work: Use lockdep to assert IRQs are disabled/enabled
irq/timings: Use lockdep to assert IRQs are disabled/enabled
perf/core: Use lockdep to assert IRQs are disabled/enabled
x86: Use lockdep to assert IRQs are disabled/enabled
smp/core: Use lockdep to assert IRQs are disabled/enabled
timers/hrtimer: Use lockdep to assert IRQs are disabled/enabled
timers/nohz: Use lockdep to assert IRQs are disabled/enabled
workqueue: Use lockdep to assert IRQs are disabled/enabled
irq/softirqs: Use lockdep to assert IRQs are disabled/enabled
locking/lockdep: Add IRQs disabled/enabled assertion APIs: lockdep_assert_irqs_enabled()/disabled()
locking/pvqspinlock: Implement hybrid PV queued/unfair locks
locking/rwlocks: Fix comments
x86/paravirt: Set up the virt_spin_lock_key after static keys get initialized
block, locking/lockdep: Assign a lock_class per gendisk used for wait_for_completion()
workqueue: Remove now redundant lock acquisitions wrt. workqueue flushes
...
|
|
Pull regmap updates from Mark Brown:
"After several quiet kernel releases we've got a couple of new features
in regmap, support for using hwspinlocks as the lock for the internal
data structures and a helper for polling on regmap_fields. The Kconfig
dependencies on hwspinlocks were annoyingly difficult to squash
between things behaving surprisingly and randconfig, I could've
squashed those commits down but might've have caused hassle with other
trees trying to use the new support.
- support for using a hwspinlock to protect the regmap
- an iopoll style helper for regmap_field"
* tag 'regmap-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Fix unused warning
regmap: Try to work around Kconfig exploding on HWSPINLOCK
regmap: Clean up hwspinlock on regmap exit
regmap: Also protect hwspinlock in error handling path
regmap: Add a config option for hwspinlock
regmap: Add hardware spinlock support
regmap: avoid -Wint-in-bool-context warning
regmap: add iopoll-like polling macro for regmap_field
regmap: constify regmap_bus structures
regmap: Avoid namespace collision within macro & tidy up
|
|
* pm-core:
ACPI / PM: Take SMART_SUSPEND driver flag into account
PCI / PM: Take SMART_SUSPEND driver flag into account
PCI / PM: Drop unnecessary invocations of pcibios_pm_ops callbacks
PM / core: Add SMART_SUSPEND driver flag
PCI / PM: Use the NEVER_SKIP driver flag
PM / core: Add NEVER_SKIP and SMART_PREPARE driver flags
PM / core: Convert timers to use timer_setup()
PM / core: Fix kerneldoc comments of four functions
PM / core: Drop legacy class suspend/resume operations
|
|
* pm-sleep:
freezer: Fix typo in freezable_schedule_timeout() comment
PM / s2idle: Clear the events_check_enabled flag
PM / sleep: Remove pm_complete_with_resume_check()
PM: ARM: locomo: Drop suspend and resume bus type callbacks
PM: Use a more common logging style
PM: Document rules on using pm_runtime_resume() in system suspend callbacks
|
|
* pm-cpufreq-sched:
cpufreq: schedutil: Reset cached_raw_freq when not in sync with next_freq
* pm-opp:
PM / OPP: Add dev_pm_opp_{un}register_get_pstate_helper()
PM / OPP: Support updating performance state of device's power domain
PM / OPP: add missing of_node_put() for of_get_cpu_node()
PM / OPP: Rename dev_pm_opp_register_put_opp_helper()
PM / OPP: Add missing of_node_put(np)
PM / OPP: Move error message to debug level
PM / OPP: Use snprintf() to avoid kasprintf() and kfree()
PM / OPP: Move the OPP directory out of power/
|
|
* pm-cpufreq: (22 commits)
cpufreq: stats: Handle the case when trans_table goes beyond PAGE_SIZE
cpufreq: arm_big_little: make cpufreq_arm_bL_ops structures const
cpufreq: arm_big_little: make function arguments and structure pointer const
cpufreq: pxa: convert to clock API
cpufreq: speedstep-lib: mark expected switch fall-through
cpufreq: ti-cpufreq: add missing of_node_put()
cpufreq: dt: Remove support for Exynos4212 SoCs
cpufreq: imx6q: Move speed grading check to cpufreq driver
cpufreq: ti-cpufreq: kfree opp_data when failure
cpufreq: SPEAr: pr_err() strings should end with newlines
cpufreq: powernow-k8: pr_err() strings should end with newlines
cpufreq: dt-platdev: drop socionext,uniphier-ld6b from whitelist
arm64: wire cpu-invariant accounting support up to the task scheduler
arm64: wire frequency-invariant accounting support up to the task scheduler
arm: wire cpu-invariant accounting support up to the task scheduler
arm: wire frequency-invariant accounting support up to the task scheduler
drivers base/arch_topology: allow inlining cpu-invariant accounting support
drivers base/arch_topology: provide frequency-invariant accounting support
cpufreq: dt: invoke frequency-invariance setter function
cpufreq: arm_big_little: invoke frequency-invariance setter function
...
|
|
* pm-qos:
PM / QoS: Fix device resume latency framework
PM / QoS: Drop PM_QOS_FLAG_REMOTE_WAKEUP
|
|
* pm-domains:
PM / Domains: Fix genpd to deal with drivers returning 1 from ->prepare()
PM / domains: Rework governor code to be more consistent
PM / Domains: Remove gpd_dev_ops.active_wakeup() callback
soc: rockchip: power-domain: Use GENPD_FLAG_ACTIVE_WAKEUP
soc: mediatek: Use GENPD_FLAG_ACTIVE_WAKEUP
ARM: shmobile: pm-rmobile: Use GENPD_FLAG_ACTIVE_WAKEUP
PM / Domains: Allow genpd users to specify default active wakeup behavior
PM / Domains: Add support to select performance-state of domains
PM / Domains: Rename genpd internals from pm_genpd_* to genpd_*
|
|
The fwnode_handle_get() function is used to obtain a reference to an
fwnode. A common usage pattern for the OF equivalent of the function is:
mynode = of_node_get(node);
Similarly make fwnode_handle_get() return the fwnode to which the
reference was obtained.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
A device probe deferred because of a device link is never probed again
because it is not added to the deferred_probe_pending_list. Add it, taking
care of the race with driver_deferred_probe_trigger().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
During system-wide PM, genpd relies on its PM callbacks to be invoked for
all its attached devices, as to deal with powering off/on the PM domain. In
other words, genpd is not compatible with the direct_complete path, if
executed by the PM core for any of its attached devices.
However, when genpd's ->prepare() callback invokes pm_generic_prepare(), it
does not take into account that it may return 1. Instead it treats that as
an error internally and expects the PM core to abort the prepare phase and
roll back. This leads to genpd not properly powering on/off the PM domain,
because its internal counters gets wrongly balanced.
To fix the behaviour, allow drivers to return 1 from their ->prepare()
callbacks, but let's return 0 from genpd's ->prepare() callback in such
case, as that prevents the PM core from running the direct_complete path
for the device.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The special value of 0 for device resume latency PM QoS means
"no restriction", but there are two problems with that.
First, device resume latency PM QoS requests with 0 as the
value are always put in front of requests with positive
values in the priority lists used internally by the PM QoS
framework, causing 0 to be chosen as an effective constraint
value. However, that 0 is then interpreted as "no restriction"
effectively overriding the other requests with specific
restrictions which is incorrect.
Second, the users of device resume latency PM QoS have no
way to specify that *any* resume latency at all should be
avoided, which is an artificial limitation in general.
To address these issues, modify device resume latency PM QoS to
use S32_MAX as the "no constraint" value and 0 as the "no
latency at all" one and rework its users (the cpuidle menu
governor, the genpd QoS governor and the runtime PM framework)
to follow these changes.
Also add a special "n/a" value to the corresponding user space I/F
to allow user space to indicate that it cannot accept any resume
latencies at all for the given device.
Fixes: 85dc0b8a4019 (PM / QoS: Make it possible to expose PM QoS latency constraints)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197323
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Ramesh Thomas <ramesh.thomas@intel.com>
|
|
|
|
The genpd governor currently uses negative PM QoS values to indicate
the "no suspend" condition and 0 as "no restriction", but it doesn't
use them consistently. Moreover, it tries to refresh QoS values for
already suspended devices in a quite questionable way.
For the above reasons, rework it to be a bit more consistent.
First off, note that dev_pm_qos_read_value() in
dev_update_qos_constraint() and __default_power_down_ok() is
evaluated for devices in suspend. Moreover, that only happens if the
effective_constraint_ns value for them is negative (meaning "no
suspend"). It is not evaluated in any other cases, so effectively
the QoS values are only updated for devices in suspend that should
not have been suspended in the first place. In all of the other
cases, the QoS values taken into account are the effective ones from
the time before the device has been suspended, so generally devices
need to be resumed and suspended again for new QoS values to take
effect anyway. Thus evaluating dev_update_qos_constraint() in
those two places doesn't make sense at all, so drop it.
Second, initialize effective_constraint_ns to 0 ("no constraint")
rather than to (-1) ("no suspend"), which makes more sense in
general and in case effective_constraint_ns is never updated
(the device is in suspend all the time or it is never suspended)
it doesn't affect the device's parent and so on.
Finally, rework default_suspend_ok() to explicitly handle the
"no restriction" and "no suspend" special cases.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Ramesh Thomas <ramesh.thomas@intel.com>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
There are no more users left of the gpd_dev_ops.active_wakeup()
callback. All have been converted to GENPD_FLAG_ACTIVE_WAKEUP.
Hence remove the callback.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
It is quite common for PM Domains to require slave devices to be kept
active during system suspend if they are to be used as wakeup sources.
To enable this, currently each PM Domain or driver has to provide its
own gpd_dev_ops.active_wakeup() callback.
Introduce a new flag GENPD_FLAG_ACTIVE_WAKEUP to consolidate this.
If specified, all slave devices configured as wakeup sources will be
kept active during system suspend.
PM Domains that need more fine-grained controls, based on the slave
device, can still provide their own callbacks, as before.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Conflicts:
include/linux/compiler-clang.h
include/linux/compiler-gcc.h
include/linux/compiler-intel.h
include/uapi/linux/stddef.h
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Make the PCI bus type take DPM_FLAG_SMART_SUSPEND into account in its
system-wide PM callbacks and make sure that all code that should not
run in parallel with pci_pm_runtime_resume() is executed in the "late"
phases of system suspend, freeze and poweroff transitions.
[Note that the pm_runtime_suspended() check in pci_dev_keep_suspended()
is an optimization, because if is not passed, all of the subsequent
checks may be skipped and some of them are much more overhead in
general.]
Also use the observation that if the device is in runtime suspend
at the beginning of the "late" phase of a system-wide suspend-like
transition, its state cannot change going forward (runtime PM is
disabled for it at that time) until the transition is over and the
subsequent system-wide PM callbacks should be skipped for it (as
they generally assume the device to not be suspended), so add checks
for that in pci_pm_suspend_late/noirq(), pci_pm_freeze_late/noirq()
and pci_pm_poweroff_late/noirq().
Moreover, if pci_pm_resume_noirq() or pci_pm_restore_noirq() is
called during the subsequent system-wide resume transition and if
the device was left in runtime suspend previously, its runtime PM
status needs to be changed to "active" as it is going to be put
into the full-power state, so add checks for that too to these
functions.
In turn, if pci_pm_thaw_noirq() runs after the device has been
left in runtime suspend, the subsequent "thaw" callbacks need
to be skipped for it (as they may not work correctly with a
suspended device), so set the power.direct_complete flag for the
device then to make the PM core skip those callbacks.
In addition to the above add a core helper for checking if
DPM_FLAG_SMART_SUSPEND is set and the device runtime PM status is
"suspended" at the same time, which is done quite often in the new
code (and will be done elsewhere going forward too).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Define and document a SMART_SUSPEND flag to instruct bus types and PM
domains that the system suspend callbacks provided by the driver can
cope with runtime-suspended devices, so from the driver's perspective
it should be safe to leave devices in runtime suspend during system
suspend.
Setting that flag may also cause middle-layer code (bus types,
PM domains etc.) to skip invocations of the ->suspend_late and
->suspend_noirq callbacks provided by the driver if the device
is in runtime suspend at the beginning of the "late" phase of
the system-wide suspend transition, in which case the driver's
system-wide resume callbacks may be invoked back-to-back with
its ->runtime_suspend callback, so the driver has to be able to
cope with that too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The motivation for this change is to provide a way to work around
a problem with the direct-complete mechanism used for avoiding
system suspend/resume handling for devices in runtime suspend.
The problem is that some middle layer code (the PCI bus type and
the ACPI PM domain in particular) returns positive values from its
system suspend ->prepare callbacks regardless of whether the driver's
->prepare returns a positive value or 0, which effectively prevents
drivers from being able to control the direct-complete feature.
Some drivers need that control, however, and the PCI bus type has
grown its own flag to deal with this issue, but since it is not
limited to PCI, it is better to address it by adding driver flags at
the core level.
To that end, add a driver_flags field to struct dev_pm_info for flags
that can be set by device drivers at the probe time to inform the PM
core and/or bus types, PM domains and so on on the capabilities and/or
preferences of device drivers. Also add two static inline helpers
for setting that field and testing it against a given set of flags
and make the driver core clear it automatically on driver remove
and probe failures.
Define and document two PM driver flags related to the direct-
complete feature: NEVER_SKIP and SMART_PREPARE that can be used,
respectively, to indicate to the PM core that the direct-complete
mechanism should never be used for the device and to inform the
middle layer code (bus types, PM domains etc) that it can only
request the PM core to use the direct-complete mechanism for
the device (by returning a positive value from its ->prepare
callback) if it also has been requested by the driver.
While at it, make the core check pm_runtime_suspended() when
setting power.direct_complete so that it doesn't need to be
checked by ->prepare callbacks.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
|
|
|
|
This patch fixes the warning of label 'err_map' defined but not used.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Trying to work with hwspinlock from built in code is painful as it can
be built modular. Invert the test for REGMAP_HWSPINLOCK for now so we
end up requiring users to depend on HWSPINLOCK=y in order to turn on the
hwspinlock code.
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We should free any hwspinlocks when we destroy the regmap, do so.
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The previous patch to allow the hwspinlock code to be disabled missed
handling the free in the error path, do so using the better IS_ENABLED()
pattern as suggested by Baolin. While we're at it also check that we have
a hardware spinlock before freeing it - the core code reports an error
when freeing an invalid lock.
Suggested-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Unlike other lock types hwspinlocks are optional and can be built
modular so we can't use them unconditionally in regmap so add a config
option that drivers that want to use hwspinlocks with regmap can select
which will ensure that hwspinlock is built in.
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On some platforms, when reading or writing some special registers through
regmap, we should acquire one hardware spinlock to synchronize between
the multiple subsystems. Thus this patch adds the hardware spinlock
support for regmap.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We want to centralize the isolation features, to be done by the housekeeping
subsystem and scheduler domain isolation is a significant part of it.
No intended behaviour change, we just reuse the housekeeping cpumask
and core code.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Wanpeng Li <kernellwp@gmail.com>
Link: http://lkml.kernel.org/r/1509072159-31808-11-git-send-email-frederic@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
Linus Torvalds
Thomas Gleixner
Sudeep Holla
Rafael J. Wysocki
Robin H. Johnson
William Breathitt Gray
Kees Cook
Sakari Ailus
Adrian Hunter
Ulf Hansson
Ingo Molnar
Geert Uytterhoeven
Mark Brown
Baolin Wang
Greg Kroah-Hartman
Frederic Weisbecker