| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Alexander reported mkswap on /dev/zram0 is failed if other process is
opening the block device file.
Step is as follows,
0. Reset the unused zram device.
1. Use a program that opens /dev/zram0 with O_RDWR and sleeps
until killed.
2. While that program sleeps, echo the correct value to
/sys/block/zram0/disksize.
3. Verify (e.g. in /proc/partitions) that the disk size is applied
correctly. It is.
4. While that program still sleeps, attempt to mkswap /dev/zram0.
This fails: mkswap: error: swap area needs to be at least 40 KiB
When I investigated, the size get by ioctl(fd, BLKGETSIZE64, xxx) on
mkswap to get a size of blockdev was zero although zram0 has right size by
2.
The reason is zram didn't revalidate disk after changing capacity so that
size of blockdev's inode is not uptodate until all of file is close.
This patch should fix the BUG.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Reported-by: Alexander E. Patrakov <patrakov@gmail.com>
Tested-by: Alexander E. Patrakov <patrakov@gmail.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We want to skip the physical block(PAGE_SIZE) which is partially covered
by the discard bio, so we check the remaining size and subtract it if
there is a need to goto the next physical block.
The current offset usage in zram_bio_discard is incorrect, it will cause
its upper filesystem breakdown. Consider the following scenario:
On some architecture or config, PAGE_SIZE is 64K for example, filesystem
is set up on zram disk without PAGE_SIZE aligned, a discard bio leads to a
offset = 4K and size=72K, normally, it should not really discard any
physical block as it partially cover two physical blocks. However, with
the current offset usage, it will discard the second physical block and
free its memory, which will cause filesystem breakdown.
This patch corrects the offset usage in zram_bio_discard.
Signed-off-by: Weijie Yang <weijie.yang@samsung.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Bob Liu <bob.liu@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
zram is ram based block device and can be used by backend of filesystem.
When filesystem deletes a file, it normally doesn't do anything on data
block of that file. It just marks on metadata of that file. This
behavior has no problem on disk based block device, but has problems on
ram based block device, since we can't free memory used for data block.
To overcome this disadvantage, there is REQ_DISCARD functionality. If
block device support REQ_DISCARD and filesystem is mounted with discard
option, filesystem sends REQ_DISCARD to block device whenever some data
blocks are discarded. All we have to do is to handle this request.
This patch implements to flag up QUEUE_FLAG_DISCARD and handle this
REQ_DISCARD request. With it, we can free memory used by zram if it isn't
used.
[akpm@linux-foundation.org: tweak comments]
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
sysfs.txt documentation lists the following requirements:
- The buffer will always be PAGE_SIZE bytes in length. On i386, this
is 4096.
- show() methods should return the number of bytes printed into the
buffer. This is the return value of scnprintf().
- show() should always use scnprintf().
Use scnprintf() in show() functions.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When we initialized zcomp with single, we couldn't change
max_comp_streams without zram reset but current interface doesn't show
any error to user and even it changes max_comp_streams's value without
any effect so it would make user very confusing.
This patch prevents max_comp_streams's change when zcomp was initialized
as single zcomp and emit the error to user(ex, echo).
[akpm@linux-foundation.org: don't return with the lock held, per Sergey]
[fengguang.wu@intel.com: fix coccinelle warnings]
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Instead of returning just NULL, return ERR_PTR from zcomp_create() if
compressing backend creation has failed. ERR_PTR(-EINVAL) for unsupported
compression algorithm request, ERR_PTR(-ENOMEM) for allocation (zcomp or
compression stream) error.
Perform IS_ERR() check of returned from zcomp_create() value in
disksize_store() and set return code to PTR_ERR().
Change suggested by Jerome Marchand.
[akpm@linux-foundation.org: clean up error recovery flow]
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reported-by: Jerome Marchand <jmarchan@redhat.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
While fixing lockdep spew of ->init_lock reported by Sasha Levin [1],
Minchan Kim noted [2] that it's better to move compression backend
allocation (using GPF_KERNEL) out of the ->init_lock lock, same way as
with zram_meta_alloc(), in order to prevent the same lockdep spew.
[1] https://lkml.org/lkml/2014/2/27/337
[2] https://lkml.org/lkml/2014/3/3/32
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reported-by: Minchan Kim <minchan@kernel.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Sasha Levin <sasha.levin@oracle.com>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add and document `comp_algorithm' device attribute. This attribute allows
to show supported compression and currently selected compression
algorithms:
cat /sys/block/zram0/comp_algorithm
[lzo] lz4
and change selected compression algorithm:
echo lzo > /sys/block/zram0/comp_algorithm
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch allows to change max_comp_streams on initialised zcomp.
Introduce zcomp set_max_streams() knob, zcomp_strm_multi_set_max_streams()
and zcomp_strm_single_set_max_streams() callbacks to change streams limit
for zcomp_strm_multi and zcomp_strm_single, accordingly. set_max_streams
for single steam zcomp does nothing.
If user has lowered the limit, then zcomp_strm_multi_set_max_streams()
attempts to immediately free extra streams (as much as it can, depending
on idle streams availability).
Note, this patch does not allow to change stream 'policy' from single to
multi stream (or vice versa) on already initialised compression backend.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Existing zram (zcomp) implementation has only one compression stream
(buffer and algorithm private part), so in order to prevent data
corruption only one write (compress operation) can use this compression
stream, forcing all concurrent write operations to wait for stream lock
to be released. This patch changes zcomp to keep a compression streams
list of user-defined size (via sysfs device attr). Each write operation
still exclusively holds compression stream, the difference is that we
can have N write operations (depending on size of streams list)
executing in parallel. See TEST section later in commit message for
performance data.
Introduce struct zcomp_strm_multi and a set of functions to manage
zcomp_strm stream access. zcomp_strm_multi has a list of idle
zcomp_strm structs, spinlock to protect idle list and wait queue, making
it possible to perform parallel compressions.
The following set of functions added:
- zcomp_strm_multi_find()/zcomp_strm_multi_release()
find and release a compression stream, implement required locking
- zcomp_strm_multi_create()/zcomp_strm_multi_destroy()
create and destroy zcomp_strm_multi
zcomp ->strm_find() and ->strm_release() callbacks are set during
initialisation to zcomp_strm_multi_find()/zcomp_strm_multi_release()
correspondingly.
Each time zcomp issues a zcomp_strm_multi_find() call, the following set
of operations performed:
- spin lock strm_lock
- if idle list is not empty, remove zcomp_strm from idle list, spin
unlock and return zcomp stream pointer to caller
- if idle list is empty, current adds itself to wait queue. it will be
awaken by zcomp_strm_multi_release() caller.
zcomp_strm_multi_release():
- spin lock strm_lock
- add zcomp stream to idle list
- spin unlock, wake up sleeper
Minchan Kim reported that spinlock-based locking scheme has demonstrated
a severe perfomance regression for single compression stream case,
comparing to mutex-based (see https://lkml.org/lkml/2014/2/18/16)
base spinlock mutex
==Initial write ==Initial write ==Initial write
records: 5 records: 5 records: 5
avg: 1642424.35 avg: 699610.40 avg: 1655583.71
std: 39890.95(2.43%) std: 232014.19(33.16%) std: 52293.96
max: 1690170.94 max: 1163473.45 max: 1697164.75
min: 1568669.52 min: 573429.88 min: 1553410.23
==Rewrite ==Rewrite ==Rewrite
records: 5 records: 5 records: 5
avg: 1611775.39 avg: 501406.64 avg: 1684419.11
std: 17144.58(1.06%) std: 15354.41(3.06%) std: 18367.42
max: 1641800.95 max: 531356.78 max: 1706445.84
min: 1593515.27 min: 488817.78 min: 1655335.73
When only one compression stream available, mutex with spin on owner
tends to perform much better than frequent wait_event()/wake_up(). This
is why single stream implemented as a special case with mutex locking.
Introduce and document zram device attribute max_comp_streams. This
attr shows and stores current zcomp's max number of zcomp streams
(max_strm). Extend zcomp's zcomp_create() with `max_strm' parameter.
`max_strm' limits the number of zcomp_strm structs in compression
backend's idle list (max_comp_streams).
max_comp_streams used during initialisation as follows:
-- passing to zcomp_create() max_strm equals to 1 will initialise zcomp
using single compression stream zcomp_strm_single (mutex-based locking).
-- passing to zcomp_create() max_strm greater than 1 will initialise zcomp
using multi compression stream zcomp_strm_multi (spinlock-based locking).
default max_comp_streams value is 1, meaning that zram with single stream
will be initialised.
Later patch will introduce configuration knob to change max_comp_streams
on already initialised and used zcomp.
TEST
iozone -t 3 -R -r 16K -s 60M -I +Z
test base 1 strm (mutex) 3 strm (spinlock)
-----------------------------------------------------------------------
Initial write 589286.78 583518.39 718011.05
Rewrite 604837.97 596776.38 1515125.72
Random write 584120.11 595714.58 1388850.25
Pwrite 535731.17 541117.38 739295.27
Fwrite 1418083.88 1478612.72 1484927.06
Usage example:
set max_comp_streams to 4
echo 4 > /sys/block/zram0/max_comp_streams
show current max_comp_streams (default value is 1).
cat /sys/block/zram0/max_comp_streams
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Do not perform direct LZO compress/decompress calls, initialise
and use zcomp LZO backend (single compression stream) instead.
[akpm@linux-foundation.org: resolve conflicts with zram-delete-zram_init_device-fix.patch]
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
allocate new `zram_meta' in disksize_store() only for uninitialised zram
device, saving a number of allocations and deallocations in case if
disksize_store() was called on currently used device. at the same time
zram_meta stack variable is not necessary, because we can set ->meta
directly. there is also no need in setting QUEUE_FLAG_NONROT queue on
every disksize_store(), set it once during device creation.
[minchan@kernel.org: handle zram->meta alloc fail case]
[minchan@kernel.org: prevent lockdep spew of init_lock]
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move zram warning about disksize and size of memory correlation to zram
documentation.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
zram accounted but did not report numbers of failed read and write
queries. make these stats available as failed_reads and failed_writes
attrs.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Introduce ZRAM_ATTR_RO macro that generates device_attribute and default
ATTR show() function for existing atomic64_t zram stats.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is a preparation patch for stats code duplication removal.
1) use atomic64_t for `pages_zero' and `pages_stored' zram stats.
2) `compr_size' and `pages_zero' struct zram_stats members did not
follow the existing device attr naming scheme: zram_stats.ATTR has
ATTR_show() function. rename them:
-- compr_size -> compr_data_size
-- pages_zero -> zero_pages
Minchan Kim's note:
If we really have trouble with atomic stat operation, we could
change it with percpu_counter so that it could solve atomic overhead and
unnecessary memory space by introducing unsigned long instead of 64bit
atomic_t.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove `good' and `bad' compressed sub-requests stats. RW request may
cause a number of RW sub-requests. zram used to account `good' compressed
sub-queries (with compressed size less than 50% of original size), `bad'
compressed sub-queries (with compressed size greater that 75% of original
size), leaving sub-requests with compression size between 50% and 75% of
original size not accounted and not reported. zram already accounts each
sub-request's compression size so we can calculate real device compression
ratio.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Do not pass rw argument down the __zram_make_request() -> zram_bvec_rw()
chain, decode it in zram_bvec_rw() instead. Besides, this is the place
where we distinguish READ and WRITE bio data directions, so account zram
RW stats here, instead of __zram_make_request(). This also allows to
account a real number of zram READ/WRITE operations, not just requests
(single RW request may cause a number of zram RW ops with separate
locking, compression/decompression, etc).
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Introduce init_done() helper function which allows us to drop `init_done'
struct zram member. init_done() uses the fact that ->init_done == 1
equals to ->meta != NULL.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
zram_meta_alloc could fail so caller should check it. Otherwise, your
system will hang.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Finally, we separated zram->lock dependency from 32bit stat/ table
handling so there is no reason to use rw_semaphore between read and
write path so this patch removes the lock from read path totally and
changes rw_semaphore with mutex. So, we could do
old:
read-read: OK
read-write: NO
write-write: NO
Now:
read-read: OK
read-write: OK
write-write: NO
The below data proves mixed workload performs well 11 times and there is
also enhance on write-write path because current rw-semaphore doesn't
support SPIN_ON_OWNER. It's side effect but anyway good thing for us.
Write-related tests perform better (from 61% to 1058%) but read path has
good/bad(from -2.22% to 1.45%) but they are all marginal within stddev.
CPU 12
iozone -t -T -l 12 -u 12 -r 16K -s 60M -I +Z -V 0
==Initial write ==Initial write
records: 10 records: 10
avg: 516189.16 avg: 839907.96
std: 22486.53 (4.36%) std: 47902.17 (5.70%)
max: 546970.60 max: 909910.35
min: 481131.54 min: 751148.38
==Rewrite ==Rewrite
records: 10 records: 10
avg: 509527.98 avg: 1050156.37
std: 45799.94 (8.99%) std: 40695.44 (3.88%)
max: 611574.27 max: 1111929.26
min: 443679.95 min: 980409.62
==Read ==Read
records: 10 records: 10
avg: 4408624.17 avg: 4472546.76
std: 281152.61 (6.38%) std: 163662.78 (3.66%)
max: 4867888.66 max: 4727351.03
min: 4058347.69 min: 4126520.88
==Re-read ==Re-read
records: 10 records: 10
avg: 4462147.53 avg: 4363257.75
std: 283546.11 (6.35%) std: 247292.63 (5.67%)
max: 4912894.44 max: 4677241.75
min: 4131386.50 min: 4035235.84
==Reverse Read ==Reverse Read
records: 10 records: 10
avg: 4565865.97 avg: 4485818.08
std: 313395.63 (6.86%) std: 248470.10 (5.54%)
max: 5232749.16 max: 4789749.94
min: 4185809.62 min: 3963081.34
==Stride read ==Stride read
records: 10 records: 10
avg: 4515981.80 avg: 4418806.01
std: 211192.32 (4.68%) std: 212837.97 (4.82%)
max: 4889287.28 max: 4686967.22
min: 4210362.00 min: 4083041.84
==Random read ==Random read
records: 10 records: 10
avg: 4410525.23 avg: 4387093.18
std: 236693.22 (5.37%) std: 235285.23 (5.36%)
max: 4713698.47 max: 4669760.62
min: 4057163.62 min: 3952002.16
==Mixed workload ==Mixed workload
records: 10 records: 10
avg: 243234.25 avg: 2818677.27
std: 28505.07 (11.72%) std: 195569.70 (6.94%)
max: 288905.23 max: 3126478.11
min: 212473.16 min: 2484150.69
==Random write ==Random write
records: 10 records: 10
avg: 555887.07 avg: 1053057.79
std: 70841.98 (12.74%) std: 35195.36 (3.34%)
max: 683188.28 max: 1096125.73
min: 437299.57 min: 992481.93
==Pwrite ==Pwrite
records: 10 records: 10
avg: 501745.93 avg: 810363.09
std: 16373.54 (3.26%) std: 19245.01 (2.37%)
max: 518724.52 max: 833359.70
min: 464208.73 min: 765501.87
==Pread ==Pread
records: 10 records: 10
avg: 4539894.60 avg: 4457680.58
std: 197094.66 (4.34%) std: 188965.60 (4.24%)
max: 4877170.38 max: 4689905.53
min: 4226326.03 min: 4095739.72
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit a0c516cbfc74 ("zram: don't grab mutex in zram_slot_free_noity")
introduced free request pending code to avoid scheduling by mutex under
spinlock and it was a mess which made code lenghty and increased
overhead.
Now, we don't need zram->lock any more to free slot so this patch
reverts it and then, tb_lock should protect it.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, the zram table is protected by zram->lock but it's rather
coarse-grained lock and it makes hard for scalibility.
Let's use own rwlock instead of depending on zram->lock. This patch
adds new locking so obviously, it would make slow but this patch is just
prepartion for removing coarse-grained rw_semaphore(ie, zram->lock)
which is hurdle about zram scalability.
Final patch in this patchset series will remove the lock from read-path
and change rw_semaphore with mutex in write path. With bonus, we could
drop pending slot free mess in next patch.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some of fields in zram->stats are protected by zram->lock which is
rather coarse-grained so let's use atomic operation without explict
locking.
This patch is ready for removing dependency of zram->lock in read path
which is very coarse-grained rw_semaphore. Of course, this patch adds
new atomic operation so it might make slow but my 12CPU test couldn't
spot any regression. All gain/lose is marginal within stddev.
iozone -t -T -l 12 -u 12 -r 16K -s 60M -I +Z -V 0
==Initial write ==Initial write
records: 50 records: 50
avg: 412875.17 avg: 415638.23
std: 38543.12 (9.34%) std: 36601.11 (8.81%)
max: 521262.03 max: 502976.72
min: 343263.13 min: 351389.12
==Rewrite ==Rewrite
records: 50 records: 50
avg: 416640.34 avg: 397914.33
std: 60798.92 (14.59%) std: 46150.42 (11.60%)
max: 543057.07 max: 522669.17
min: 304071.67 min: 316588.77
==Read ==Read
records: 50 records: 50
avg: 4147338.63 avg: 4070736.51
std: 179333.25 (4.32%) std: 223499.89 (5.49%)
max: 4459295.28 max: 4539514.44
min: 3753057.53 min: 3444686.31
==Re-read ==Re-read
records: 50 records: 50
avg: 4096706.71 avg: 4117218.57
std: 229735.04 (5.61%) std: 171676.25 (4.17%)
max: 4430012.09 max: 4459263.94
min: 2987217.80 min: 3666904.28
==Reverse Read ==Reverse Read
records: 50 records: 50
avg: 4062763.83 avg: 4078508.32
std: 186208.46 (4.58%) std: 172684.34 (4.23%)
max: 4401358.78 max: 4424757.22
min: 3381625.00 min: 3679359.94
==Stride read ==Stride read
records: 50 records: 50
avg: 4094933.49 avg: 4082170.22
std: 185710.52 (4.54%) std: 196346.68 (4.81%)
max: 4478241.25 max: 4460060.97
min: 3732593.23 min: 3584125.78
==Random read ==Random read
records: 50 records: 50
avg: 4031070.04 avg: 4074847.49
std: 192065.51 (4.76%) std: 206911.33 (5.08%)
max: 4356931.16 max: 4399442.56
min: 3481619.62 min: 3548372.44
==Mixed workload ==Mixed workload
records: 50 records: 50
avg: 149925.73 avg: 149675.54
std: 7701.26 (5.14%) std: 6902.09 (4.61%)
max: 191301.56 max: 175162.05
min: 133566.28 min: 137762.87
==Random write ==Random write
records: 50 records: 50
avg: 404050.11 avg: 393021.47
std: 58887.57 (14.57%) std: 42813.70 (10.89%)
max: 601798.09 max: 524533.43
min: 325176.99 min: 313255.34
==Pwrite ==Pwrite
records: 50 records: 50
avg: 411217.70 avg: 411237.96
std: 43114.99 (10.48%) std: 33136.29 (8.06%)
max: 530766.79 max: 471899.76
min: 320786.84 min: 317906.94
==Pread ==Pread
records: 50 records: 50
avg: 4154908.65 avg: 4087121.92
std: 151272.08 (3.64%) std: 219505.04 (5.37%)
max: 4459478.12 max: 4435857.38
min: 3730512.41 min: 3101101.67
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit a0c516cbfc74 ("zram: don't grab mutex in zram_slot_free_noity")
introduced pending zram slot free in zram's write path in case of
missing slot free by memory allocation failure in zram_slot_free_notify
but it is not necessary because we have already freed the slot right
before overwriting.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Sergey reported we don't need to handle pending free request every I/O
so that this patch removes it in read path while we remain it in write
path.
Let's consider below example.
Swap subsystem ask to zram "A" block free by swap_slot_free_notify but
zram had been pended it without real freeing. Swap subsystem allocates
"A" block for new data but request pended for a long time just handled
and zram blindly free new data on the "A" block. :(
That's why we couldn't remove handle pending free request right before
zram-write.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Dan and Sergey reported that there is a racy between reset and flushing
of pending work so that it could make oops by freeing zram->meta in
reset while zram_slot_free can access zram->meta if new request is
adding during the race window.
This patch moves flush after taking init_lock so it prevents new request
so that it closes the race.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add my copyright to the zram source code which I maintain.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove the old private compcache project address so upcoming patches
should be sent to LKML because we Linux kernel community will take care.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Zram has lived in staging for a LONG LONG time and have been
fixed/improved by many contributors so code is clean and stable now. Of
course, there are lots of product using zram in real practice.
The major TV companys have used zram as swap since two years ago and
recently our production team released android smart phone with zram
which is used as swap, too and recently Android Kitkat start to use zram
for small memory smart phone. And there was a report Google released
their ChromeOS with zram, too and cyanogenmod have been used zram long
time ago. And I heard some disto have used zram block device for tmpfs.
In addition, I saw many report from many other peoples. For example,
Lubuntu start to use it.
The benefit of zram is very clear. With my experience, one of the
benefit was to remove jitter of video application with backgroud memory
pressure. It would be effect of efficient memory usage by compression
but more issue is whether swap is there or not in the system. Recent
mobile platforms have used JAVA so there are many anonymous pages. But
embedded system normally are reluctant to use eMMC or SDCard as swap
because there is wear-leveling and latency issues so if we do not use
swap, it means we can't reclaim anoymous pages and at last, we could
encounter OOM kill. :(
Although we have real storage as swap, it was a problem, too. Because
it sometime ends up making system very unresponsible caused by slow swap
storage performance.
Quote from Luigi on Google
"Since Chrome OS was mentioned: the main reason why we don't use swap
to a disk (rotating or SSD) is because it doesn't degrade gracefully
and leads to a bad interactive experience. Generally we prefer to
manage RAM at a higher level, by transparently killing and restarting
processes. But we noticed that zram is fast enough to be competitive
with the latter, and it lets us make more efficient use of the
available RAM. " and he announced.
http://www.spinics.net/lists/linux-mm/msg57717.html
Other uses case is to use zram for block device. Zram is block device
so anyone can format the block device and mount on it so some guys on
the internet start zram as /var/tmp.
http://forums.gentoo.org/viewtopic-t-838198-start-0.html
Let's promote zram and enhance/maintain it instead of removing.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Nitin Gupta <ngupta@vflare.org>
Acked-by: Pekka Enberg <penberg@kernel.org>
Cc: Bob Liu <bob.liu@oracle.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Luigi Semenzato <semenzato@google.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Seth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
Minchan Kim
Weijie Yang
Joonsoo Kim
Sergey Senozhatsky