| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Commit '3d035f580699 ("drivers/char/hpet.c: allow user controlled mmap for
user processes")' introduced a new kernel command line parameter hpet_mmap,
that is required to expose the memory map of the HPET registers to
user-space. Unfortunately the kernel command line parameter 'hpet_mmap' is
broken and never takes effect due to missing '=' character in the __setup()
code of hpet_mmap_enable.
Before this patch:
dmesg output with the kernel command line parameter hpet_mmap=1
[ 0.204152] HPET mmap disabled
dmesg output with the kernel command line parameter hpet_mmap=0
[ 0.204192] HPET mmap disabled
After this patch:
dmesg output with the kernel command line parameter hpet_mmap=1
[ 0.203945] HPET mmap enabled
dmesg output with the kernel command line parameter hpet_mmap=0
[ 0.204652] HPET mmap disabled
Fixes: 3d035f580699 ("drivers/char/hpet.c: allow user controlled mmap for user processes")
Signed-off-by: Buland Singh <bsingh@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is no advantage to keep 'struct file_operations.open & .close'
API's. So removed the unnecessary code efi_rtc_open & efi_rtc_close.
Signed-off-by: Naveen Kumar Parna <parna.naveenkumar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Adopt nvram module to reduce code duplication. This means CONFIG_NVRAM
becomes available to PPC64 builds. Previously it was only available to
PPC32 builds because it depended on CONFIG_GENERIC_NVRAM.
The IOC_NVRAM_GET_OFFSET ioctl as implemented on PPC64 validates the
offset returned by pmac_get_partition(). Do the same in the nvram module.
Note that the old PPC32 generic_nvram module lacked this test.
So when CONFIG_PPC32 && CONFIG_PPC_PMAC, the IOC_NVRAM_GET_OFFSET ioctl
would have returned 0 (always). But when CONFIG_PPC64 && CONFIG_PPC_PMAC,
the IOC_NVRAM_GET_OFFSET ioctl would have returned -1 (which is -EPERM)
when the requested partition was not found.
With this patch, the result is now -EINVAL on both PPC32 and PPC64 when
the requested PowerMac NVRAM partition is not found. This is a userspace-
visible change, in the non-existent partition case, which would be in
an error path for an IOC_NVRAM_GET_OFFSET ioctl syscall.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Switch PPC32 kernels from the generic_nvram module to the nvram module.
Also fix a theoretical bug where CHRP omits the chrp_nvram_init() call
when CONFIG_NVRAM_MODULE=m.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the powerpc-specific ioctls to the nvram module. This allows the nvram
module to replace the generic_nvram module.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Atari RTC NVRAM uses a checksum so implement the remaining arch_nvram_ops
methods for the set_checksum and initialize ioctls. Enable
CONFIG_HAVE_ARCH_NVRAM_OPS.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Refactor the RTC "CMOS" NVRAM functions so that they can be used as
arch_nvram_ops methods. Checksumming logic is moved from the misc device
operations to the nvram read/write operations. This makes the misc device
implementation more generic.
This preserves the locking mechanism such that "read if checksum valid"
and "write and update checksum" remain atomic operations.
Some platforms implement byte-range read/write methods which are similar
to file_operations struct methods. Other platforms provide only
byte-at-a-time methods. The former are more efficient but may be
unavailable so fall back on the latter methods when necessary.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The drivers/char/nvram.c module has previously supported only RTC "CMOS"
NVRAM, for which it provides appropriate checksum ioctls. Make these
ioctls optional so the module can be re-used with other kinds of NVRAM.
The ops struct methods that implement the ioctls now return error
codes so that a multi-platform kernel binary can do the right thing when
running on hardware without a suitable NVRAM.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
NVRAMs on different platforms and architectures have different attributes
and access methods. E.g. some platforms have byte-at-a-time accessor
functions while others have byte-range accessor functions. Some have
checksum functionality while others do not. By calling ops struct methods
via the common wrapper functions, the nvram module and other drivers can
make use of the available NVRAM functionality in a portable way.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove the nvram_read_byte() and nvram_write_byte() declarations in
powerpc/include/asm/nvram.h and use the cross-platform static functions
in linux/nvram.h instead.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace nvram_* functions with static functions in nvram.h. These will
become wrappers for struct nvram_ops method calls.
This patch effectively disables existing NVRAM functionality so as to
allow the rest of the series to be bisected without build failures.
That functionality is gradually re-implemented in subsequent patches.
Replace the sole validate-checksum-and-read-byte sequence with a call to
nvram_read() which will gain the same semantics in subsequent patches.
Remove unused exports.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Also give functions more sensible names: nvram_misc_* for misc device ops,
nvram_proc_* for proc file ops and nvram_module_* for init and exit
functions. This prevents name collisions with nvram.h helper functions
and improves readability.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move the m68k-specific code out of the driver to make the driver generic.
I've used 'SPDX-License-Identifier: GPL-2.0+' for the new file because the
old file is covered by MODULE_LICENSE("GPL").
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On powerpc, setting CONFIG_NVRAM=n builds a kernel with no NVRAM support.
Setting CONFIG_NVRAM=m enables the /dev/nvram misc device module without
enabling NVRAM support in drivers. Setting CONFIG_NVRAM=y enables the
misc device (built-in) and also enables NVRAM support in drivers.
m68k shares the valkyriefb driver with powerpc, and since that driver uses
NVRAM, it is affected by CONFIG_ATARI_SCSI, because of the use of
"select NVRAM". We can avoid the "select" here, but drivers still have
to interpret the CONFIG_NVRAM symbol consistently regardless of platform.
In this patch and the subsequent fbdev driver patch, the convention is
adopted across all relevant platforms whereby NVRAM functionality gets
enabled in a given device driver when the nvram misc device is built-in
or when both drivers are modules.
Acked-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ipcnum is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/char/mwave/mwavedd.c:299 mwave_ioctl() warn: potential spectre issue 'pDrvData->IPCs' [w] (local cap)
Fix this by sanitizing ipcnum before using it to index pDrvData->IPCs.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull TPM updates from James Morris:
- Support for partial reads of /dev/tpm0.
- Clean up for TPM 1.x code: move the commands to tpm1-cmd.c and make
everything to use the same data structure for building TPM commands
i.e. struct tpm_buf.
* 'next-tpm' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (25 commits)
tpm: add support for partial reads
tpm: tpm_ibmvtpm: fix kdoc warnings
tpm: fix kdoc for tpm2_flush_context_cmd()
tpm: tpm_try_transmit() refactor error flow.
tpm: use u32 instead of int for PCR index
tpm1: reimplement tpm1_continue_selftest() using tpm_buf
tpm1: reimplement SAVESTATE using tpm_buf
tpm1: rename tpm1_pcr_read_dev to tpm1_pcr_read()
tpm1: implement tpm1_pcr_read_dev() using tpm_buf structure
tpm: tpm1: rewrite tpm1_get_random() using tpm_buf structure
tpm: tpm-space.c remove unneeded semicolon
tpm: tpm-interface.c drop unused macros
tpm: add tpm_auto_startup() into tpm-interface.c
tpm: factor out tpm_startup function
tpm: factor out tpm 1.x pm suspend flow into tpm1-cmd.c
tpm: move tpm 1.x selftest code from tpm-interface.c tpm1-cmd.c
tpm: factor out tpm1_get_random into tpm1-cmd.c
tpm: move tpm_getcap to tpm1-cmd.c
tpm: move tpm1_pcr_extend to tpm1-cmd.c
tpm: factor out tpm_get_timeouts()
...
|
|
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- new %ptR printk format
- rename core files
- allow registration of multiple nvmem devices
New driver:
- i.MX system controller RTC
Driver updates:
- abx80x: handle voltage ioctls, correct binding doc
- m41t80: correct month in alarm reads
- pcf85363: add pcf85263 support
- pcf8523: properly handle battery low flag
- s3c: limit alarm to one year in the future as ALMYEAR is broken
- sun6i: rework clock output binding"
* tag 'rtc-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (54 commits)
rtc: rename core files
rtc: nvmem: fix possible use after free
rtc: add i.MX system controller RTC support
dt-bindings: fsl: scu: add rtc binding
rtc: pcf2123: Add Microcrystal rv2123
rtc: class: reimplement devm_rtc_device_register
rtc: enforce rtc_timer_init private_data type
rtc: abx80x: Implement RTC_VL_READ,CLR ioctls
rtc: pcf85363: Add support for NXP pcf85263 rtc
dt-bindings: rtc: pcf85363: Document pcf85263 real-time clock
rtc: pcf8523: don't return invalid date when battery is low
dt-bindings: rtc: use a generic node name for ds1307
PM: Switch to use %ptR
m68k/mac: Switch to use %ptR
Input: hp_sdc_rtc - Switch to use %ptR
rtc: tegra: Switch to use %ptR
rtc: s5m: Switch to use %ptR
rtc: s3c: Switch to use %ptR
rtc: rx8025: Switch to use %ptR
rtc: rx6110: Switch to use %ptR
...
|
|
Pull char/misc driver updates from Greg KH:
"Here is the big set of char and misc driver patches for 4.21-rc1.
Lots of different types of driver things in here, as this tree seems
to be the "collection of various driver subsystems not big enough to
have their own git tree" lately.
Anyway, some highlights of the changes in here:
- binderfs: is it a rule that all driver subsystems will eventually
grow to have their own filesystem? Binder now has one to handle the
use of it in containerized systems.
This was discussed at the Plumbers conference a few months ago and
knocked into mergable shape very fast by Christian Brauner. Who
also has signed up to be another binder maintainer, showing a
distinct lack of good judgement :)
- binder updates and fixes
- mei driver updates
- fpga driver updates and additions
- thunderbolt driver updates
- soundwire driver updates
- extcon driver updates
- nvmem driver updates
- hyper-v driver updates
- coresight driver updates
- pvpanic driver additions and reworking for more device support
- lp driver updates. Yes really, it's _finally_ moved to the proper
parallal port driver model, something I never thought I would see
happen. Good stuff.
- other tiny driver updates and fixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (116 commits)
MAINTAINERS: add another Android binder maintainer
intel_th: msu: Fix an off-by-one in attribute store
stm class: Add a reference to the SyS-T document
stm class: Fix a module refcount leak in policy creation error path
char: lp: use new parport device model
char: lp: properly count the lp devices
char: lp: use first unused lp number while registering
char: lp: detach the device when parallel port is removed
char: lp: introduce list to save port number
bus: qcom: remove duplicated include from qcom-ebi2.c
VMCI: Use memdup_user() rather than duplicating its implementation
char/rtc: Use of_node_name_eq for node name comparisons
misc: mic: fix a DMA pool free failure
ptp: fix an IS_ERR() vs NULL check
genwqe: Fix size check
binder: implement binderfs
binder: fix use-after-free due to ksys_close() during fdget()
bus: fsl-mc: remove duplicated include files
bus: fsl-mc: explicitly define the fsl_mc_command endianness
misc: ti-st: make array read_ver_cmd static, shrinks object size
...
|
|
Pull tty/serial driver updates from Greg KH:
"Here is the large TTY/Serial driver set of patches for 4.21-rc1.
A number of small serial driver changes along with some good tty core
fixes for long-reported issues with locking. There is also a new
console font added to the tree, for high-res screens, so that should
be helpful for many.
The last patch in the series is a revert of an older one in the tree,
it came late but it resolves a reported issue that linux-next was
having for some people.
Full details are in the shortlog, and all of these, with the exception
of the revert, have been in linux-next for a while with no reported
issues"
* tag 'tty-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (85 commits)
Revert "serial: 8250: Default SERIAL_OF_PLATFORM to SERIAL_8250"
serial: sccnxp: Allow to use non-standard baud rates
serial: sccnxp: Adds a delay between sequential read/write cycles
tty: serial: qcom_geni_serial: Fix UART hang
tty: serial: qcom_geni_serial: Fix wrap around of TX buffer
serial: max310x: Fix tx_empty() callback
dt-bindings: serial: sh-sci: Document r8a774c0 bindings
dt-bindings: serial: sh-sci: Document r8a774a1 bindings
Fonts: New Terminus large console font
dt-bindings: serial: lpuart: add imx8qxp compatible string
serial: uartps: Fix interrupt mask issue to handle the RX interrupts properly
serial: uartps: Fix error path when alloc failed
serial: uartps: Check if the device is a console
serial: uartps: Add the device_init_wakeup
tty: serial: samsung: Increase maximum baudrate
tty: serial: samsung: Properly set flags in autoCTS mode
tty: Use of_node_name_{eq,prefix} for node name comparisons
tty/serial: do not free trasnmit buffer page under port lock
serial: 8250: Rate limit serial port rx interrupts during input overruns
dt-bindings: serial: 8250: Add rate limit for serial port input overruns
...
|
|
totalram_pages and totalhigh_pages are made static inline function.
Main motivation was that managed_page_count_lock handling was complicating
things. It was discussed in length here,
https://lore.kernel.org/patchwork/patch/995739/#1181785 So it seemes
better to remove the lock and convert variables to atomic, with preventing
poteintial store-to-read tearing as a bonus.
[akpm@linux-foundation.org: coding style fixes]
Link: http://lkml.kernel.org/r/1542090790-21750-4-git-send-email-arunks@codeaurora.org
Signed-off-by: Arun KS <arunks@codeaurora.org>
Suggested-by: Michal Hocko <mhocko@suse.com>
Suggested-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reviewed-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: David Hildenbrand <david@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull crypto updates from Herbert Xu:
"API:
- Add 1472-byte test to tcrypt for IPsec
- Reintroduced crypto stats interface with numerous changes
- Support incremental algorithm dumps
Algorithms:
- Add xchacha12/20
- Add nhpoly1305
- Add adiantum
- Add streebog hash
- Mark cts(cbc(aes)) as FIPS allowed
Drivers:
- Improve performance of arm64/chacha20
- Improve performance of x86/chacha20
- Add NEON-accelerated nhpoly1305
- Add SSE2 accelerated nhpoly1305
- Add AVX2 accelerated nhpoly1305
- Add support for 192/256-bit keys in gcmaes AVX
- Add SG support in gcmaes AVX
- ESN for inline IPsec tx in chcr
- Add support for CryptoCell 703 in ccree
- Add support for CryptoCell 713 in ccree
- Add SM4 support in ccree
- Add SM3 support in ccree
- Add support for chacha20 in caam/qi2
- Add support for chacha20 + poly1305 in caam/jr
- Add support for chacha20 + poly1305 in caam/qi2
- Add AEAD cipher support in cavium/nitrox"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (130 commits)
crypto: skcipher - remove remnants of internal IV generators
crypto: cavium/nitrox - Fix build with !CONFIG_DEBUG_FS
crypto: salsa20-generic - don't unnecessarily use atomic walk
crypto: skcipher - add might_sleep() to skcipher_walk_virt()
crypto: x86/chacha - avoid sleeping under kernel_fpu_begin()
crypto: cavium/nitrox - Added AEAD cipher support
crypto: mxc-scc - fix build warnings on ARM64
crypto: api - document missing stats member
crypto: user - remove unused dump functions
crypto: chelsio - Fix wrong error counter increments
crypto: chelsio - Reset counters on cxgb4 Detach
crypto: chelsio - Handle PCI shutdown event
crypto: chelsio - cleanup:send addr as value in function argument
crypto: chelsio - Use same value for both channel in single WR
crypto: chelsio - Swap location of AAD and IV sent in WR
crypto: chelsio - remove set but not used variable 'kctx_len'
crypto: ux500 - Use proper enum in hash_set_dma_transfer
crypto: ux500 - Use proper enum in cryp_set_dma_transfer
crypto: aesni - Add scatter/gather avx stubs, and use them in C
crypto: aesni - Introduce partial block macro
..
|
|
Modify lp driver to use the new parallel port device model.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the parallel port is usb based and the lp attaches to it based on
LP_PARPORT_AUTO, we do get /dev/lp0 and when we remove the usb device
/dev/lp0 is unregistered. If we now reconnect the usb device we get
our /dev/lp0 back. But if we now disconnect and reconnect eight times
we donot get any lp device and dmesg shows:
lp: ignoring parallel port (max. 8)
Decrement the lp_count when the device detaches as this represents the
number of lp devices connected to the system.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the parallel port is usb based and the lp attaches to it based on
LP_PARPORT_AUTO, we do get /dev/lp0 and when we remove the usb device
/dev/lp0 is unregistered. But if we now reconnect the usb device we get
/dev/lp1, another disconnection and reconnection and we get /dev/lp2.
Use the port number array to find the first unused lp number and use
that to register the lp device with the parallel port.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the parallel port is usb based and the lp attaches to it, we do
get /dev/lp0, but when we remove the usb device and the parallel port
is gone, we are still left with /dev/lp0.
Unregister the device properly in the detach routine based on the port
number it has connected to.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When we are registering lp in LP_PARPORT_AUTO mode, we are not keeping
any record of the parallel port number to which lp is connecting.
Add an array to save the port number to it.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
The open coded iterating thru the child node names is converted to use
for_each_child_of_node() instead.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently to read a response from the TPM device an application needs
provide big enough buffer for the whole response and read it in one go.
The application doesn't know how big the response it beforehand so it
always needs to maintain a 4K buffer and read the max (4K).
In case if the user of the TSS library doesn't provide big enough
buffer the TCTI spec says that the library should set the required
size and return TSS2_TCTI_RC_INSUFFICIENT_BUFFER error code so that the
application could allocate a bigger buffer and call receive again.
To make it possible in the TSS library, this requires being able to do
partial reads from the driver.
The library would read the 10 bytes header first to get the actual size
of the response from the header, and then read the rest of the response.
This patch adds support for partial reads, i.e. the user can read the
response in one or multiple reads, until the whole response is consumed.
The user can also read only part of the response and ignore
the rest by issuing a new write to send a new command.
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Note, we drop the validation option. This is only used in
a deprecated ABI and is mostly wrong as many RTCs will still be valid
after 2100.
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that synchronize_rcu() waits for preempt-disable regions of code
as well as RCU read-side critical sections, synchronize_sched() can be
replaced by synchronize_rcu(). This commit therefore makes this change.
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <openipmi-developer@lists.sourceforge.net>
Acked-by: Corey Minyard <cminyard@mvista.com>
|
|
Fixes the checkpatch warning:
"space prohibited between function name and open parenthesis"
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fixes checkpatch warning:
"foo * bar should be foo *bar"
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fixes the checkpatch error:
ERROR: code indent should use tabs where possible
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
return is not a function, parentheses are not required.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix checkpatch errors for trailing if else statements.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix checkpatch error for trailing whitespace.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In preparation for adding XChaCha12 support, rename/refactor
chacha20-generic to support different numbers of rounds. The
justification for needing XChaCha12 support is explained in more detail
in the patch "crypto: chacha - add XChaCha12 support".
The only difference between ChaCha{8,12,20} are the number of rounds
itself; all other parts of the algorithm are the same. Therefore,
remove the "20" from all definitions, structures, functions, files, etc.
that will be shared by all ChaCha versions.
Also make ->setkey() store the round count in the chacha_ctx (previously
chacha20_ctx). The generic code then passes the round count through to
chacha_block(). There will be a ->setkey() function for each explicitly
allowed round count; the encrypt/decrypt functions will be the same. I
decided not to do it the opposite way (same ->setkey() function for all
round counts, with different encrypt/decrypt functions) because that
would have required more boilerplate code in architecture-specific
implementations of ChaCha and XChaCha.
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Adopt the SPDX license identifier headers to ease license compliance
management. While we are at this fix the comment style, too.
Cc: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Remove redundant lines in the kdoc:
Fixes kdoc warnings:
drivers/char/tpm/tpm_ibmvtpm.c:42: warning: Cannot understand *
on line 42 - I thought it was a doc line
drivers/char/tpm/tpm_ibmvtpm.c:57: warning: Cannot understand *
on line 57 - I thought it was a doc line
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
kdoc for tpm2_flush_context_cmd() was off.
Fixes: 9aa36b399a50 ("tpm: export tpm2_flush_context_cmd")'
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
First, rename out_no_locality to out_locality for bailing out on
both tpm_cmd_ready() and tpm_request_locality() failure.
Second, ignore the return value of go_to_idle() as it may override
the return value of the actual tpm operation, the go_to_idle() error
will be caught on any consequent command.
Last, fix the wrong 'goto out', that jumped back instead of forward.
Cc: stable@vger.kernel.org
Fixes: 627448e85c76 ("tpm: separate cmd_ready/go_idle from runtime_pm")
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
The TPM specs defines PCR index as a positive number, and there is
no reason to use a signed number. It is also a possible security
issue as currently no functions check for a negative index,
which may become a large number when converted to u32.
Adjust the API to use u32 instead of int in all PCR related
functions.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Reimplement tpm1_continue_selftest() using tpm_buf structure.
This is the last command using the old tpm_cmd_t structure
and now the structure can be removed.
Cc: Nayna Jain <nayna@linux.vnet.ibm.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
In tpm1_pm_suspend() function reimplement,
TPM_ORD_SAVESTATE comamnd using tpm_buf.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Rename tpm1_pcr_read_dev to tpm1_pcr_read() to match
the counterpart tpm2_pcr_read().
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Implement tpm1_pcr_read_dev() using tpm_buf and remove
now unneeded structures from tpm.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
Buland Singh
Naveen Kumar Parna
Finn Thain
Gustavo A. R. Silva
Linus Torvalds
Arun KS
Sudip Mukherjee
Rob Herring
Tadeusz Struk
Andy Shevchenko
Yangtao Li
Paul E. McKenney
Eric Biggers
Stefan Wahren
Tomas Winkler