| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Fabia PLL is a Digital Frequency Locked Loop (DFLL) clock
generator which has a wide range of frequency output. It
supports dynamic updating of the output frequency
("frequency slewing") without need to turn off the PLL
before configuration. Add support for initial configuration
and programming sequence to control fabia PLLs.
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
[sboyd: Shorten code a little]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Some of the divider settings are preconfigured and should not
be changed by the clock framework during frequency change. This
patch adds the read-only divider operation for QCOM alpha pll
post divider which is equivalent to generic divider operations in
'commit 79c6ab509558 ("clk: divider: add CLK_DIVIDER_READ_ONLY flag")'.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The Brammo type of Alpha PLL doesn't allow configuration of a
VCO, but it does support dynamic update in which the frequency
can be changed dynamically without turning off the PLL.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The Huayra type Alpha PLL has a 16 bit alpha value, and
depending on the alpha_mode, the alpha value can be treated as
M/N value or as a two’s compliment number. This PLL supports
dynamic programming.
Since the decoding of alpha val and dynamic programming are
completely different from other Alpha PLLs we add separate
functions for Huayra PLLs.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Some of the Alpha PLLs support dynamic update in which the
frequency can be changed dynamically without turning off the PLL.
This dynamic update requires the following sequence:
1. Write the desired values to L_VAL and ALPHA_VAL registers
2. Toggle pll_latch_input from low to high
3. Wait for pll_ack_latch to transition from low to high
The new L and alpha values have been latched. It may
take some time for the PLL to fully settle with these
new values.
4. Pull pll_latch_input low
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The current configuration does not fully configure PLL alpha mode
and values so this patch
1. Configures PLL_ALPHA_VAL_U for PLL which supports 40 bit alpha.
2. Adds alpha enable and alpha mode configuration support.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The alpha value calculation has been written for 40-bit alpha
values which doesn't work work properly for 16-bit ones. The
alpha value is calculated on the basis of ALPHA_BITWIDTH to make
the computation easy for 40 bit alpha. After calculating the 32
bit alpha, it is converted to 40 bit alpha by making lower bits
zero. But if actual alpha register width is less than
ALPHA_BITWIDTH, then the actual width can be used for
calculation. This also means, during the 40 bit alpha pll set
rate path, the lower alpha register is not configured
Change the code to calculate the rate and register values from
'alpha_width' instead of hard-coding it so that it can work for
the different widths that are supported.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Alpha PLL is a generic name used for QCOM PLLs which uses L and
Alpha values for configuring the integer and fractional part.
QCOM SoCs use different types of Alpha PLLs for which basic
software configuration part is common with following differences.
1. All these PLLs have the same basic registers like
PLL_MODE, L_VAL, ALPHA_VAL but some of the register offsets are
different between PLLs types.
2. The dynamic programming sequence is different in some
of the Alpha PLLs
3. Some of the PLLs don’t have 64 bit config control, 64 bit
user control, VCO configuration, etc.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The votable alpha PLLs need to have the fsm mode enabled as part
of the initialization. The sequence seems to be the same as used
by clk-pll, so move the function which does this into a common
place and reuse it for the clk-alpha-pll
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Some alpha PLLs have support for only a 16bit programable Alpha Value
(as against the default 40bits). Add a flag to handle the 16bit alpha
registers
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add a function to do initial configuration of the alpha plls
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Some PLLs can support an HW FSM mode (different from the Votable FSMs,
though its the same bit used to enable Votable FSMs as well as HW FSMs)
which enables the HW to do the bypass/reset/enable-output-ctrl sequence
on its own. So all thats needed from SW is to set the FSM_ENA bit.
PLL_ACTIVE_FLAG is whats used to check if the PLL is active/enabled.
Some of the PLLs which support HW FSM can also need an OFFLINE request
that needs to be toggled across the enable/disable. We use a flag to
identify such cases and handle them.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add support for configuring rates of, enabling, and disabling
Alpha PLLs. This is sufficient for the types of PLLs found in
the global and multimedia clock controllers.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
Amit Nischal
Abhishek Sahu
Rajendra Nayak
Stephen Boyd