| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
PWM2 is commonly used to control voltage of PWM regulator of VDD_LOG in
RK3399. On the Firefly-RK3399 board, PWM2 outputs 40 KHz square wave
from power on and the VDD_LOG is about 0.9V. When the kernel boots
normally into the system, the PWM2 keeps outputing PWM signal.
But the kernel hangs randomly after "Starting kernel ..." line on that
board. When it happens, PWM2 outputs high level which causes VDD_LOG
drops to 0.4V below the normal operating voltage.
By adding "pclk_rkpwm_pmu" to the rk3399_pmucru_critical_clocks array,
PWM clock is ensured to be prepared at startup and the PWM2 output is
normal. After repeated tests, the early boot hang is gone.
This patch works on both Firefly-RK3399 and ROC-RK3399-PC boards.
Signed-off-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
This fix rounds the clock rate properly by using quotient and not
remainder in the calculation. This issue was found while testing HDMI
in the Juno platform.
Fixes: 6d6a1d82eaef7 ("clk: add support for clocks provided by SCMI")
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add support for the display clock controller found on SDM845
based devices. This would allow display drivers to probe and
control their clocks.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
[sboyd@kernel.org: Remove CLK_GET_RATE_NOCACHE everywhere]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
When building armada-37xx-periph, num_parents isn't used in function
clk_pm_cpu_get_parent:
drivers/clk/mvebu/armada-37xx-periph.c: In function ‘clk_pm_cpu_get_parent’:
drivers/clk/mvebu/armada-37xx-periph.c:419:6: warning: unused variable ‘num_parents’ [-Wunused-variable]
int num_parents = clk_hw_get_num_parents(hw);
^~~~~~~~~~~
Remove the declaration of num_parents to dispose the warning.
Fixes: 616bf80d381d ("clk: mvebu: armada-37xx-periph: Fix wrong return value in get_parent")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Remove unused 'mout_user_aclk400_mcuisp_p4x12' variable to fix GCC warning:
drivers/clk/samsung/clk-exynos4412-isp.c:40:27: warning:
'mout_user_aclk400_mcuisp_p4x12' defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Exynos5440 drivers removal
The Exynos5440 (quad-core A15 with GMAC, PCIe, SATA) was targeting
server platforms but it did not make it to the market really. There are
no development boards with it and probably there are no real products
neither. The development for Exynos5440 ended in 2013 and since then
the platform is in maintenance mode.
Removing Exynos5440 makes our life slightly easier: less maintenance,
smaller code, reduced number of quirks, no need to preserve DTB
backward-compatibility.
The Device Tree sources and some of the drivers for Exynos5440 were
already removed. This removes remaining drivers.
* tag 'samsung-drivers-exynos5440-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
usb: host: exynos: Remove support for Exynos5440
clk: samsung: Remove support for Exynos5440
cpufreq: exynos: Remove support for Exynos5440
ata: ahci-platform: Remove support for Exynos5440
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add Actions Semi S700 SoC clock support
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add REGMAP_MMIO as dependency to avoid undefined
reference to regmap symbols.
Fixes: d85d20053e19 ("clk: actions: Add S900 SoC clock support")
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add clock control for SPI controller on UniPhier SoCs.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add USB3 PHY clocks where missing. Use fixed-factor clocks for those
without gating.
For clarification, prefix clock names with 'ss' or 'hs'.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The Denali NAND controller IP needs three clocks:
- clk: controller core clock
- clk_x: bus interface clock
- ecc_clk: clock at which ECC circuitry is run
Currently, only the first one (50MHz) is provided. The rest of the
two clock ports must be connected to the 200MHz clock line. Add this.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
These clocks have low jitter paths to certain parents. To model these
correctly, use the sdmmc mux divider clock type.
Signed-off-by: Peter De-Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add a clock type to model the sdmmc switch divider clocks which have paths
to source clocks bypassing the divider (Low Jitter paths). These
are handled by selecting the lj path when the divider is 1 (ie the
rate is the parent rate), otherwise the normal path with divider
will be selected. Otherwise this clock behaves as a normal peripheral
clock.
Signed-off-by: Peter De-Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Move this to a separate file so it can be used to calculate the sdmmc
clock dividers.
Signed-off-by: Peter De-Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add the missing linux/delay.h include statement for udelay() used by
fence_udelay() macro.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
of_find_compatible_node() is returning a device node with refcount
incremented and must be explicitly decremented after the last use
which is right after the us in of_iomap() here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 4a5f720b6542 ("clk: imx: add clock driver for imx6sll")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
of_find_compatible_node() is returning a device node with refcount
incremented and must be explicitly decremented after the last use
which is right after the us in of_iomap() here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 787b4271a6a0 ("clk: imx: add imx6ul clk tree support")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
i.MX6SX has a 16KB always-on ocram bank called
ocram_s, and its clock gate in CCM CCGR1 CG14
needs to be enabled before access, add it to
clock tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The return value of the get_parent operation is a u8, whereas a -EINVAL
was returned. This wrong value was return if the value was bigger that
the number of parent but this case was already handled by the core.
So we can just remove this chunk of code to fix the issue.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 9818a7a4fd10 ("clk: mvebu: armada-37xx-periph: prepare cpu clk to
be used with DVFS")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Fixed factor clock has two initializations at of_clk_init() time
and during platform driver probe. Before of_clk_init() call,
node is marked as populated and so its probe never gets called.
During of_clk_init() fixed factor clock registration may fail if
any of its parent clock is not registered. In this case, it doesn't
get chance to retry registration from probe. Clear OF_POPULATED
flag if fixed factor clock registration fails so that clock
registration is attempted again from probe.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Patch "clk: core: Copy connection id" made it so that the connector id
'con_id' is kstrdup_const()ed to cater to drivers that pass non-constant
connection ids. The patch added the corresponding kfree_const to
__clk_free_clk(), but struct clk's can be freed also via __clk_put().
Add the kfree_const call to __clk_put() and add comments to both
functions to remind that the logic in them should be kept in sync.
Fixes: 253160a8ad06 ("clk: core: Copy connection id")
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
SPDX headers updated for common/branch/pll/regmap files.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The Exynos5440 is not actively developed, there are no development
boards available and probably there are no real products with it.
Remove wide-tree support for Exynos5440.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Sylwester Nawrocki <snawrocki@kernel.org>
|
|
Add the RPMh clock driver to control the RPMh managed clock resources on
some of the Qualcomm Technologies, Inc. SoCs.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
[sboyd@kernel.org: Clean up whitespace, indentation, remove
cmd_db_ready check]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The HPLL can be configured through a register (SCU24), however some
platforms chose to configure it through the strapping settings and do
not use the register. This was not noticed as the logic for bit 18 in
SCU24 was confused: set means programmed, but the driver read it as set
means strapped.
This gives us the correct HPLL value on Palmetto systems, from which
most of the peripheral clocks are generated.
Fixes: 5eda5d79e4be ("clk: Add clock driver for ASPEED BMC SoCs")
Cc: stable@vger.kernel.org # v4.15
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
__of_clk_get() calls of_parse_phandle_with_args(), which rejects
negative indices since commit bd69f73f2c81eed9 ("of: Create function for
counting number of phandles in a property").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add clkctrl data for the m_can clocks and register it within the
clkctrl driver
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
CC: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This clock is needed for iMX mailbox driver
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Switching the CPU from the L2 or L3 frequencies (300 and 200 Mhz
respectively) to L0 frequency (1.2 Ghz) requires a significant amount
of time to let VDD stabilize to the appropriate voltage. This amount of
time is large enough that it cannot be covered by the hardware
countdown register. Due to this, the CPU might start operating at L0
before the voltage is stabilized, leading to CPU stalls.
To work around this problem, we prevent switching directly from the
L2/L3 frequencies to the L0 frequency, and instead switch to the L1
frequency in-between. The sequence therefore becomes:
1. First switch from L2/L3(200/300MHz) to L1(600MHZ)
2. Sleep 20ms for stabling VDD voltage
3. Then switch from L1(600MHZ) to L0(1200Mhz).
It is based on the work done by Ken Ma <make@marvell.com>
Cc: stable@vger.kernel.org
Fixes: 2089dc33ea0e ("clk: mvebu: armada-37xx-periph: add DVFS support for cpu clocks")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
GEN_CLK is able to route several internal clocks to one of the SoC
pads. In the future, even more clocks could be made accessible using
cts_msr_clk - the clock measure block.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
HHI_GEN_CLK_CTNL is defined twice, just remove the duplicate definition
Fixes: 738f66d3211d ("clk: gxbb: add AmLogic GXBB clk controller driver")
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
Adding clocks for the pcie driver. Due to the ASIC design,
the pcie controller re-use part of the mipi clock logic,
so the mipi clock is also added.
Tested-by: Jianxin Qin <jianxin.qin@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
[amended to remove unnecessary locales]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
clk-audio-divider is no longer used, we can remove it.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
It is actually a lot easier to setup the PLL with carefully chosen rates
than relying on CCF clock propagation for this audio use case.
This way, we can make sure we will always be able to provide the common
audio clock rates, while having the PLL in the optimal operating range.
For this, we stop the rate propagation at the mux picking the
PLL and let it round to the closest matching PLL.
Doing so, we can use the generic divider for the i2s clock.
clk-audio-divider is no longer required. It was a (poor) attempt
to use CCF rate propagation while making sure the PLL rate would
be high enough to work with audio use cases.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
The axg audio clock controller is the clock generation unit for the
amlogic audio subsystem of A113 based SoCs. It may be clocked by 8
different plls provided by the primary clock controller and also by
10 slave bit clocks and 10 slave sample clocks which may be provided
by external components, such as audio codecs, through the SoC pads.
It contains several muxes, dividers and gates which are fed into the
the different devices of the audio subsystem.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
Add a driver to control the clock divider found in the sample clock
generator of the axg audio clock controller.
The sclk divider accumulates specific features which make the generic
divider unsuitable to control it:
- zero based divider (div = val + 1), but zero value gates the clock,
so minimum divider value is 2.
- lrclk variant may adjust the duty cycle depending the divider value
and the 'hi' value.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
|
|
Add a driver to control the output of the sample clock generator found
in the axg audio clock controller.
The goal of this driver is to coherently control the phase provided to
the different element using the sample clock generator. This simplify
the usage of the sample clock generator a lot, without comprising the
ability of the SoC.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
Add a driver based meson clk-regmap to control clock phase on
amlogic SoCs
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
Clean the dependencies in meson clock Kconfig.
CLK_AMLOGIC should actually select CLK_REGMAP_MESON which it uses. Also,
each platform should select CLK_AMLOGIC, so everything is properly turned
on when the platform Kconfig enable each configuration flag
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
The legacy method to access the hhi register space is not longer used.
We can safely drop it now.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
Apparently there was an attempt to avoid out-of-bounds accesses when there
is only one memory timing available, but there is a typo in the code that
neglects that attempt.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Memory Controller should be always-on. Currently the sibling EMC clock is
marked as critical, let's mark MC clock too for consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The current default is to leave the VDE clock's parent at the default,
which is clk_m. However, that is not a configuration that will allow the
VDE to function. Reparent it to pll_c3 instead to make sure the hardware
can actually decode video content.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
By default, the vic03 clock is a child of pll_m but that runs at 924 MHz
which is too fast for VIC. Make vic03 a child of pll_c3 by default so it
will run at a supported frequency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
When registering clocks, we just skip any that fail to register
(leaving a NULL hole in the clock table). However, our of_xlate
function still tries to dereference each entry while looking for
the clock with the requested id, causing a crash if any clocks
failed to register. Add a check to of_xlate to skip any NULL
clocks.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Register, shift and mask were wrong according to datasheet.
Fixes: 115510053e5e ("clk: rockchip: add clock controller for the RK3399")
Cc: stable@vger.kernel.org
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Frequency table macro is used by multiple clock drivers, move frequency
table macro to common header file.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
Levin Du
Kuninori Morimoto
Amit Daniel Kachhap
Taniya Das
Anders Roxell
Krzysztof Kozlowski
Olof Johansson
Saravanan Sekar
Kunihiko Hayashi
Masahiro Yamada
Peter De-Schrijver
Aapo Vienamo
Nicholas Mc Guire
Anson Huang
Gregory CLEMENT
Rajan Vaja
Mikko Perttunen
Joel Stanley
Geert Uytterhoeven
Faiz Abbas
Oleksij Rempel
Jerome Brunet
Yixun Lan
Dmitry Osipenko
Thierry Reding
Alberto Panizzo