| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull ARM SoC fixes from Arnd Bergmann:
"Here are a bunch of small bug fixes for various ARM platforms, nothing
really sticks out this week, most of either fixes bugs in code that
was just added in 4.4, or that has been broken for many years without
anyone noticing.
at91/sama5d2:
- fix sama5de hardware setup of sd/mmc interface
- proper selection of pinctrl drivers. PIO4 is necessary for sama5d2
berlin:
- fix incorrect clock input for SDIO
exynos:
- Fix potential NULL pointer dereference in Exynos PMU driver.
imx:
- Fix vf610 SAI clock configuration bug which is discovered by the
newly added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
ixp4xx:
- fix prototypes for readl/writel functions
ls2080a:
- use little-endian register access for GPIO and SDHCI
omap:
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of when
MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
pxa:
- use PWM lookup table for all ezx machines
s3c24xx:
- Remove incorrect __init annotation from s3c24xx cpufreq driver
structures.
versatile:
- fix PCI IRQ mapping on Versatile PB"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ls2080a/dts: Add little endian property for GPIO IP block
dt-bindings: define little-endian property for QorIQ GPIO
ARM64: dts: ls2080a: fix eSDHC endianness
ARM: dts: vf610: use reset values for L2 cache latencies
ARM: pxa: use PWM lookup table for all machines
ARM: dts: berlin: add 2nd clock for BG2Q sdhci0 and sdhci1
ARM: dts: berlin: correct BG2Q's sdhci2 2nd clock
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM: at91: fix pinctrl driver selection
ARM: at91/dt: add always-on to 1.8V regulator
ARM: dts: vf610: fix clock definition for SAI2
ARM: imx: clk-vf610: fix SAI clock tree
ARM: ixp4xx: fix read{b,w,l} return types
irqchip/versatile-fpga: Fix PCI IRQ mapping on Versatile PB
ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE
ARM: dts: add dm816x missing spi DT dma handles
ARM: dts: add dm816x missing #mbox-cells
cpufreq: s3c24xx: Do not mark s3c2410_plls_add as __init
ARM: EXYNOS: Fix potential NULL pointer access in exynos_sys_powerdown_conf
|
|
Reference the newly added efuse clock-ids in the clock-tree.
Signed-off-by: ZhengShunQian <zhengsq@rock-chips.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add the clock tree definition for the new rk3228 SoC.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
RK3228's armclk has 3 parents, so allow cpuclk to have
more than 2 parents.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The APBS clock on sun9i is the same as the APB0 clock on sun8i. With
sun9i we are supporting the PRCM clocks by using CLK_OF_DECLARE,
instead of through a PRCM mfd device and subdevices for each clock
and reset control. As such we need a CLK_OF_DECLARE version of
the sun8i-a23-apb0-clk driver.
Also, build it for sun9i/A80, and not just for configurations with
MFD_SUN6I_PRCM enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add a new R-Car H3 Clock Pulse Generator / Module Standby and Software
Reset driver, using the new CPG/MSSR driver core.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add the common core for the new Renesas Clock Pulse Generator / Module
Standby and Software Reset driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Extract cpg_div6_register(), to allow registering div6 clocks from
another clock driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Renesas DIV6 clocks provide a single clock output. Hence make the
"clock-output-names" DT property optional instead of mandatory. In case
the DT property is omitted the DT node name will be used.
Rename the variable "name" to "clk_name" to make the code more similar
with fixed-factor-clock.c, and to avoid a conflict with a nested local
variable while we're at it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Shmobile is all multiplatform these days, so get rid of the reference to
CONFIG_ARCH_SHMOBILE_MULTI in drivers/clk/shmobile/.
Also instead of always enabling DIV6 and MSTP adjust the Makefile
to enable DIV6 and MSTP depending on if they are included in the
SoC or not.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The video engine has its own special module clock, consisting of a clock
gate, configurable dividers, and a reset control.
On later (sun[68]i) families, the reset control is moved out of this
piece of hardware and grouped with reset controls of other peripherals.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The H3 clock control unit is similar to the those of other sun8i family
members like the A23.
It adds a new bus gates clock similar to the simple gates, but with a
different parent clock for each single gate.
Some of the gates use the new AHB2 clock as parent, whose clock source
is muxable between AHB1 and PLL6/2. The documentation isn't totally clear
about which devices belong to AHB2 now, especially USB EHIC/OHIC, so it
is mostly based on Allwinner kernel source code.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The A10/A20 share the same set of DRAM clock gates, which controls
direct memory access for some peripherals.
On the A10, bit 15 controls the system's DRAM clock output (possibly
to the DRAM chips), which we need to keep on.
On the A20 this has been moved to the DRAM controller, becoming a no-op.
However it is still listed in the user manual, so add it anyway.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
BCM63138 has a simple clocking domain which is primarily the ARMPLL
clocking complex, from which the ARM (CPU), APB and AXI clocks would be
derived from.
Since the ARMPLL controller is entirely compatible with the iProc ARM
PLL, we just initialize it without additional parameters.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The timer clock aliases are needed early on dm814x. Let's also
add the aliases for the interconnects and MMC.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Due to a copy-paste error the the rk3368 cpuclk settings were acessing
rk3288-specific register offsets. This never caused problems till now,
as cpu frequency scaling in't used currently at all.
Reported-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
* clk-fixes:
clk: sunxi: pll2: Fix clock running too fast
clk: scpi: add missing of_node_put
clk: qoriq: fix memory leak
imx/clk-pllv2: fix wrong do_div() usage
imx/clk-pllv1: fix wrong do_div() usage
clk: mmp: add linux/clk.h includes
clk: ti: drop locking code from mux/divider drivers
clk: ti816x: Add missing dmtimer clkdev entries
clk: ti: fapll: fix wrong do_div() usage
clk: ti: clkt_dpll: fix wrong do_div() usage
clk: gpio: Get parent clk names in of_gpio_clk_setup()
|
|
Contrary to what the datasheet says, the pre divider doesn't seem to be
incremented by one in the PLL2, but just uses the value from the register,
with 0 being a bypass.
This fixes the audio playing too fast.
Since we now have the same pre-divider flags, and the only difference with
the A10 is the post-divider offset, also remove the structure to just pass
the offset as an argument.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fixes: eb662f854710 ("clk: sunxi: pll2: Add A13 support")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Currently, of_clk_get_parent_name() returns a wrong parent clock name
when "clock-indices" property exists and the target index is not
found in the property. In this case, NULL should be returned.
For example,
oscillator {
compatible = "myclocktype";
#clock-cells = <1>;
clock-indices = <1>, <3>;
clock-output-names = "clka", "clkb";
};
consumer {
compatible = "myclockconsumer";
clocks = <&oscillator 0>, <&oscillator 1>;
};
Currently, of_clk_get_parent_name(consumer_np, 0) returns "clka"
(and of_clk_get_parent_name(consumer_np, 1) also returns "clka",
this is correct). Because the "clock-indices" in the clock parent
does not contain <0>, of_clk_get_parent_name(consumer_np, 0) should
return NULL.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add aclk_bus and aclk_peri to the list of rk3368 critical clocks,
which are the base clocks that supply for all peripherals, never
to be disabled automatically.
Signed-off-by: Jianqun xu <jay.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
To obtain exact pixel clocks, allow the DI clock selectors to influence
the PLLs that they are derived from.
Commit 4591b13289b5 ("ARM: i.MX6: ipu_di_sel clocks can set parent
rates") did this for i.MX6.
Port it to enable high display resolutions on i.MX53 based platforms
such as CX9020 Embedded PC, too.
Signed-off-by: Patrick Brünn <p.bruenn@beckhoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
As we already have a 'imx_check_clocks' to do the clock error
check, so cleanup the error check code.
Signed-off-by: Bai Ping <b51503@freescale.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add a virtual arm clk to abstract the actual steps
when changing the ARM core frequency.So we can using
the 'cpufreq-dt' driver on i.MX7D/Solo.
Signed-off-by: Bai Ping <b51503@freescale.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Synchronous Audio Interface (SAI) instances are clocked by
independent clocks: The bus clock and the audio clock (as shown in
Figure 51-1 in the Vybrid Reference Manual). The clock gates in
CCGR0/CCGR1 for SAI0 through SAI3 are bus clock gates, as access
tests to the registers with/without gating those clocks have shown.
The audio clock is gated by the SAIx_EN gates in CCM_CSCDR1,
followed by a clock divider (SAIx_DIV). Currently, the parent of
the bus clock gates has been assigned to SAIx_DIV, which is not
involved in the bus clock path for the SAI instances (see chapter
9.10.12, SAI clocking in the Vybrid Reference Manual).
Fix this by define the parent clock of VF610_CLK_SAIx to be the bus
clock.
If the driver needs the audio clock (when used in master mode), a
fixed device tree is required which assign the audio clock properly
to VF610_CLK_SAIx_DIV.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Most rk3368 boards (especially those with Pmic that followed the lead
from rk3368-evb-act8846) have a PWM regulator on them for vdd_logic.
This is the main voltage for all kinds of misc stuff including the
memory controller.
On these boards it is critically important to make sure that the PWM
never ever glitches and never loses its clock. Any glitch could
crash the system.
Right now there are no users of the PWM regulator and also Linux
thinks that the PWM regulator is disabled. Things happen to work
because firmware configured the PWM and Linux doesn't touch it.
..and the PWM's clock is marked as "ignore unused".
...but things _stop_ working if we turn off serial console. Why?
Because:
1. Serial console shares a parent clock with the PWM (pclk_cpu)
2. If we have no serial console then nobody is holding pclk_cpu on
at reboot time. It gets disabled.
We need to fix a lot of the above problems, but until we get
everything right the cleanest "hack" seems like it is to just keep
the "rk_pwm" clock on always.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Lots of header files are never included outside of a mach-pxa
directory and do not need to be made visible in include/mach,
so let's just move them all down one level.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The mmp clock drivers currently hardcode the physical addresses for
the clock registers. This is generally a bad idea, and it also gets in
the way of multiplatform builds, which make the platform header files
inaccessible to device drivers.
To work around the header file problem, this patch changes the calling
convention so the three mmp clock drivers get initialized with the base
addresses as arguments from the platform code.
It would still be useful to have a larger rework of the clock drivers,
with DT integration to let the clocks actually be probed automatically,
and the base addresses passed as DT properties. I am unsure if anyone
is still interested in the mmp platform, so it is possible that this
won't happen.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Chao Xie <chao.xie@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
|
|
We've been seeing some crashes at reboot test on rk3288-based systems,
which boards have not reset pin connected to NPOR, they reboot by
setting 0xfdb9 to RK3288_GLB_SRST_FST register. If the APLL works in
a high frequency mode, some IPs might hang during soft reset.
It appears that we can fix the problem by switching to slow mode before
reboot, just like what we did before suspend.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The "cpus" clock is the clock for the embedded processor in the A80.
It is also part of the PRCM clock tree. This clock includes a pre-
divider on one of its inputs. For now we are using a custom clock
driver for it. In the future we may want to develop a generalized
driver for these types of clocks, which also includes the AHB clock
driver on sun[5678]i.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This patch adds support for the PRCM apbs clock gates found on the
Allwinner A80 SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
* clk-msm8996:
clk: qcom: Add MSM8996 Multimedia Clock Controller (MMCC) driver
clk: qcom: Add gfx3d ping-pong PLL frequency switching
clk: qcom: Add MSM8996 Global Clock Control (GCC) driver
clk: qcom: Add Alpha PLL support
clk: divider: Cap table divider values to 'width' member
|
|
Add a driver for the multimedia clock controller found on MSM8996
based devices. This should allow most multimedia device drivers
to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The GPU clocks on msm8996 have three dedicated PLLs, MMPLL2,
MMPLL8, and MMPLL9. We leave MMPLL9 at the maximum speed (624
MHz), and we use MMPLL2 and MMPLL8 for the other frequencies. To
make switching frequencies faster, we ping-pong between MMPLL2
and MMPLL8 when we're switching between frequencies that aren't
the maximum. Implement custom rcg clk ops for this type of
frequency switching.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add support for the global clock controller found on MSM8996
based devices. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add support for configuring rates of, enabling, and disabling
Alpha PLLs. This is sufficient for the types of PLLs found in
the global and multimedia clock controllers.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
When we use a clk divider with a divider table, we limit the
maximum divider value in divider_get_val() to the
div_mask(width), but when we calculate the divider in
divider_round_rate() we don't consider that the maximum divider
may be limited by the width. Pass the width along to
_get_table_maxdiv() so that we only return the maximum divider
that is valid. This is useful for clocks that want to share the
same divider table while limiting the available dividers to some
subset of the table depending on the width of the bitfield.
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
This patch adds CS2000 Fractional-N driver as clock provider.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[sboyd@codeaurora.org: Fix unsigned checked for < 0 in
cs2000_ratio_get()]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
for_each_available_child_of_node performs an of_node_get on each iteration,
so a break out of the loop requires an of_node_put.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
If get_pll_div() fails we exited by returning NULL but we missed
releasing hwc.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Fixes: 0dfc86b3173f ("clk: qoriq: Move chip-specific knowledge into driver")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
do_div() is meant to be used with an unsigned dividend.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
do_div() is meant to be used with an unsigned dividend.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Pull TI clock driver fixes from Tero Kristo:
* 'for-4.4-rc/ti-clk-fixes' of https://github.com/t-kristo/linux-pm:
clk: ti: drop locking code from mux/divider drivers
clk: ti816x: Add missing dmtimer clkdev entries
clk: ti: fapll: fix wrong do_div() usage
clk: ti: clkt_dpll: fix wrong do_div() usage
|
|
The word "cases" is doubled. Keep decent forms for the following
lines.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Errata i810 states that DPLL controller can get stuck while transitioning
to a power saving state, while its M/N ratio is being re-programmed.
As a workaround, before re-programming the M/N ratio, SW has to ensure
the DPLL cannot start an idle state transition. SW can disable DPLL
idling by setting the DPLL AUTO_DPLL_MODE=0 or keeping a clock request
active by setting a dependent clock domain in SW_WKUP.
This errata impacts OMAP5 and DRA7 chips, so enable the errata for these.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
sclk_mipidsi_24m is the gating of mipi dsi phy.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The common clk implementation for MMP broke without anyone noticing
when we stopped including linux/clk.h from the clk-provider header.
This did not show up in the defconfig builds because those use the
legacy MMP clk drivers, and it did not show up in my randconfig tests
either because I was testing with my mmp multiplatform series
applied, which at some point gained the fixup.
This fixes the three broken files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 61ae76563ec3 ("clk: Remove clk.h from clk-provider.h")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
OSC can be used as USB hub source clock. An example we can route to
CLK2_P imx6 pin.
This show a usage example:
[...]
usb_hub: usb-hub {
compatible = "smsc,usb3503a";
clocks = <&clks IMX6QDL_CLK_LVDS2_GATE>;
clock-names = "refclk";
};
};
[...]
&clks {
assigned-clocks = <&clks IMX6QDL_CLK_LVDS2_SEL>;
assigned-clock-parents = <&clks IMX6QDL_CLK_OSC>;
};
/sys/kernel/debug/clk/clk_summary
osc 5 5 24000000 0 0
[...]
lvds2_sel 1 1 24000000 0 0
lvds2_gate 1 1 24000000 0 0
[...]
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add 'is_prepared' callback function for pllv3 type clk to make sure when
the system is bootup, the unused clk is in a known state to match the
prepare count info.
Signed-off-by: Bai Ping <b51503@freescale.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The 'osc' clock is already initialized by the fixed clock defined in
imx25.dtsi. The imx25 clock driver tries to add this clock for a second
time and fails with -EEXIST:
i.MX clk 1: register failed with -17
As the clock is already properly setup in DT with a different driver, we
can completely remove the handling in the imx25 clock driver.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
TI's mux and divider clock drivers do not require locking and they do
not initialize internal spinlocks. This code was occasionally
copy-posted from generic mux/divider drivers. So remove it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
Linus Torvalds
ZhengShunQian
Jeffy Chen
Chen-Yu Tsai
Geert Uytterhoeven
Magnus Damm
Jens Kuske
Florian Fainelli
Tony Lindgren
Heiko Stuebner
Stephen Boyd
Maxime Ripard
Masahiro Yamada
Jianqun xu
Patrick Brünn
Bai Ping
Stefan Agner
Caesar Wang
Arnd Bergmann
Chris Zhong
Kuninori Morimoto
Julia Lawall
Sudip Mukherjee
Nicolas Pitre
Tero Kristo
Michael Trimarchi
Markus Pargmann
Grygorii Strashko