| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Crypto self-tests reveal an error:
alg: skcipher: cbc-des3-ccp encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
The offset value should not be recomputed when retrieving the context.
Also, a code path exists which makes decisions based on older (version 3)
hardware; a v3 device deosn't support 3DES so remove this check.
Fixes: 990672d48515 ('crypto: ccp - Enable 3DES function on v5 CCPs')
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Updated testmgr will exhibit this error message when loading the
ccp-crypto module:
alg: skcipher: cfb-aes-ccp encryption failed with err -22 on test vector 3, cfg="in-place"
Update the CCP crypto driver to correctly treat CFB as a streaming mode
cipher (instead of block mode). Update the configuration for CFB to
specify the block size as a single byte;
Fixes: 2b789435d7f3 ('crypto: ccp - CCP AES crypto API support')
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
CFB mode should be treated as a stream cipher, not block.
Fixes: 63b945091a07 ('crypto: ccp - CCP device driver and interface support')
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Currently there is a mismatch b/w the ICID (Isolation Context ID) used
for DMA mapping keys and ICID used for accessing them.
-keys are DMA mapped using a job ring device, thus a job ring ICID
-keys are accessed from descriptors enqueued via Queue Interface,
thus using QI ICID
[Note: ICIDs of JRs, QI are configured by U-boot / other entity by:
-fixing up the corresponding job ring and controller DT nodes
-setting up corresponding caam ICID registers]
In order to avoid IOMMU faults, DMA map the key using the controller
device instead of a job ring device.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When IOMMU is enabled, iova -> phys address translation should be
performed using iommu_ops, not dma_to_phys().
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Use the controller device for caam/qi instead of allocating
a new platform device.
This is needed as a preparation to add support for working behind an
SMMU. A platform device allocated using platform_device_register_full()
is not completely set up - most importantly .dma_configure()
is not called.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Currently we allow top level code, i.e. that which sits between the
low level (HW-specific) drivers and crypto API, to be built as several
drivers: caamalg, caamhash, caam_pkc, caamrng, caamalg_qi.
There is no advantage in this, more it interferes with adding support
for deferred probing (there are no corresponding devices and thus
no bus).
Convert these drivers and call init() / exit() manually at the right
time.
Move algorithms initialization at JR probe / remove time:
-the first probed JR registers the crypto algs
-the last removed JR unregisters the crypto algs
Note: caam_qi_init() is called before JR platform devices creation
(of_populate_bus()), such that QI interface is initialized when
the caam/qi algorithms are registered in the JR driver (by calling
caam_qi_algapi_init().
While here, fix the Kconfig entries under CRYPTO_DEV_FSL_CAAM_JR
to be aligned.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
According to CAAM RM:
-crypto engine reads 4 S/G entries (64 bytes) at a time,
even if the S/G table has fewer entries
-it's the responsibility of the user / programmer to make sure
this HW behaviour has no side effect
The drivers do not take care of this currently, leading to IOMMU faults
when the S/G table ends close to a page boundary - since only one page
is DMA mapped, while CAAM's DMA engine accesses two pages.
Fix this by rounding up the number of allocated S/G table entries
to a multiple of 4.
Note that in case of two *contiguous* S/G tables, only the last table
might needs extra entries.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When enabling IOMMU support, the following issue becomes visible
in the AEAD zero-length case.
Even though the output sequence length is set to zero, the crypto engine
tries to prefetch 4 S/G table entries (since SGF bit is set
in SEQ OUT PTR command - which is either generated in SW in case of
caam/jr or in HW in case of caam/qi, caam/qi2).
The DMA read operation will trigger an IOMMU fault since the address in
the SEQ OUT PTR is "dummy" (set to zero / not obtained via DMA API
mapping).
1. In case of caam/jr, avoid the IOMMU fault by clearing the SGF bit
in SEQ OUT PTR command.
2. In case of caam/qi - setting address, bpid, length to zero for output
entry in the compound frame has a special meaning (cf. CAAM RM):
"Output frame = Unspecified, Input address = Y. A unspecified frame is
indicated by an unused SGT entry (an entry in which the Address, Length,
and BPID fields are all zero). SEC obtains output buffers from BMan as
prescribed by the preheader."
Since no output buffers are needed, modify the preheader by setting
(ABS = 1, ADDBUF = 0):
-"ABS = 1 means obtain the number of buffers in ADDBUF (0 or 1) from
the pool POOL ID"
-ADDBUF: "If ABS is set, ADD BUF specifies whether to allocate
a buffer or not"
3. In case of caam/qi2, since engine:
-does not support FLE[FMT]=2'b11 ("unused" entry) mentioned in DPAA2 RM
-requires output entry to be present, even if not used
the solution chosen is to leave output frame list entry zeroized.
Fixes: 763069ba49d3 ("crypto: caam - handle zero-length AEAD output")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
If a zero length request is submitted through the skcipher api,
do not offload it and return success.
Reviewed-by: Conor Mcloughlin <conor.mcloughlin@intel.com>
Tested-by: Sergey Portnoy <sergey.portnoy@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Return -EINVAL if a request for a block cipher is not multiple of the
size of the block.
This problem was found with by the new extra run-time crypto self test.
Reviewed-by: Conor Mcloughlin <conor.mcloughlin@intel.com>
Tested-by: Sergey Portnoy <sergey.portnoy@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
If an invalid key is provided as input to the setkey function, the
function always failed returning -ENOMEM rather than -EINVAL.
Furthermore, if setkey was called multiple times with an invalid key,
the device instance was getting leaked.
This patch fixes the error paths in the setkey functions by returning
the correct error code in case of error and freeing all the resources
allocated in this function in case of failure.
This problem was found with by the new extra run-time crypto self test.
Reviewed-by: Conor Mcloughlin <conor.mcloughlin@intel.com>
Tested-by: Sergey Portnoy <sergey.portnoy@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The block size for aes counter mode was improperly set to AES_BLOCK_SIZE.
This sets it to 1 as it is a stream cipher.
This problem was found with by the new extra run-time crypto self test.
Reviewed-by: Conor Mcloughlin <conor.mcloughlin@intel.com>
Tested-by: Sergey Portnoy <sergey.portnoy@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Allocate a contiguous buffer and instruct the qat hardware to return the
iv at the end of an encryption or decryption operation.
The iv is copied to the array provided by the user in the callback
function.
This problem was found with by the crypto self test.
Reviewed-by: Conor Mcloughlin <conor.mcloughlin@intel.com>
Tested-by: Sergey Portnoy <sergey.portnoy@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The offset is calculated based on type of hash algorithum.
If the algorithum is invalid the offset can have negative value.
Hence added negative offset check and return -EFAULT.
Reviewed-by: Conor Mcloughlin <conor.mcloughlin@intel.com>
Tested-by: Sergey Portnoy <sergey.portnoy@intel.com>
Signed-off-by: Shant KumarX Sonnad <shant.kumarx.sonnad@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Remove unnecessary spin lock in qat_ablkcipher_setkey.
Reviewed-by: Conor Mcloughlin <conor.mcloughlin@intel.com>
Tested-by: Sergey Portnoy <sergey.portnoy@intel.com>
Signed-off-by: Xin Zeng <xin.zeng@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Pull SPDX update from Greg KH:
"Here is a series of patches that add SPDX tags to different kernel
files, based on two different things:
- SPDX entries are added to a bunch of files that we missed a year
ago that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the
last big sweep, or they were Makefile/Kconfig files, which we
didn't touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the
next few weeks as the tools and reviewers crunch through the more
"odd" variants of how to say "GPLv2" that developers have come up with
over the years, combined with other fun oddities (GPL + a BSD
disclaimer?) that are being unearthed, with the goal for the whole
kernel to be cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches"
* tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (24 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 25
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 24
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 23
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 22
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 21
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 20
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 19
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 18
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 17
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 15
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 14
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 13
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 12
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 11
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 10
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 9
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 7
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 5
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 4
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 3
...
|
|
Pull crypto fixes from Herbert Xu:
- Two long-standing bugs in the powerpc assembly of vmx
- Stack overrun caused by HASH_MAX_DESCSIZE being too small
- Regression in caam
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: vmx - ghash: do nosimd fallback manually
crypto: vmx - CTR: always increment IV as quadword
crypto: hash - fix incorrect HASH_MAX_DESCSIZE
crypto: caam - fix typo in i.MX6 devices list for errata
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation 51
franklin street fifth floor boston ma 02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154042.432790911@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
VMX ghash was using a fallback that did not support interleaving simd
and nosimd operations, leading to failures in the extended test suite.
If I understood correctly, Eric's suggestion was to use the same
data format that the generic code uses, allowing us to call into it
with the same contexts. I wasn't able to get that to work - I think
there's a very different key structure and data layout being used.
So instead steal the arm64 approach and perform the fallback
operations directly if required.
Fixes: cc333cd68dfa ("crypto: vmx - Adding GHASH routines for VMX module")
Cc: stable@vger.kernel.org # v4.1+
Reported-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The kernel self-tests picked up an issue with CTR mode:
alg: skcipher: p8_aes_ctr encryption test failed (wrong result) on test vector 3, cfg="uneven misaligned splits, may sleep"
Test vector 3 has an IV of FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFD, so
after 3 increments it should wrap around to 0.
In the aesp8-ppc code from OpenSSL, there are two paths that
increment IVs: the bulk (8 at a time) path, and the individual
path which is used when there are fewer than 8 AES blocks to
process.
In the bulk path, the IV is incremented with vadduqm: "Vector
Add Unsigned Quadword Modulo", which does 128-bit addition.
In the individual path, however, the IV is incremented with
vadduwm: "Vector Add Unsigned Word Modulo", which instead
does 4 32-bit additions. Thus the IV would instead become
FFFFFFFFFFFFFFFFFFFFFFFF00000000, throwing off the result.
Use vadduqm.
This was probably a typo originally, what with q and w being
adjacent. It is a pretty narrow edge case: I am really
impressed by the quality of the kernel self-tests!
Fixes: 5c380d623ed3 ("crypto: vmx - Add support for VMS instructions by ASM")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Nayna Jain <nayna@linux.ibm.com>
Tested-by: Nayna Jain <nayna@linux.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Fix a typo in the list of i.MX6 devices affected by an
issue wherein AXI bus transactions may not occur in
the correct order.
Fixes: 33d69455e402 ("crypto: caam - limit AXI pipeline to a depth of
1")
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Pull ARM SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to
multiplatform enabled.
- Cleanups of Davinci
This also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
ARM: debug-ll: add default address for digicolor
ARM: u300: regulator: add MODULE_LICENSE()
ARM: ep93xx: move private headers out of mach/*
ARM: ep93xx: move pinctrl interfaces into include/linux/soc
ARM: ep93xx: keypad: stop using mach/platform.h
ARM: ep93xx: move network platform data to separate header
ARM: stm32: add AMBA support for stm32 family
MAINTAINERS: update arch/arm/mach-davinci
ARM: rockchip: add missing of_node_put in rockchip_smp_prepare_pmu
ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
soc: ixp4xx: qmgr: Add DT probe code
soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
soc: ixp4xx: npe: Add DT probe code
soc: ixp4xx: Add DT bindings for IXP4xx NPE
soc: ixp4xx: qmgr: Pass resources
soc: ixp4xx: Remove unused functions
soc: ixp4xx: Uninline several functions
soc: ixp4xx: npe: Pass addresses as resources
ARM: ixp4xx: Turn the QMGR into a platform device
ARM: ixp4xx: Turn the NPE into a platform device
...
|
|
Merge in a few pending fixes from pre-5.1 that didn't get sent in:
MAINTAINERS: update arch/arm/mach-davinci
ARM: dts: ls1021: Fix SGMII PCS link remaining down after PHY disconnect
ARM: dts: imx6q-logicpd: Reduce inrush current on USBH1
ARM: dts: imx6q-logicpd: Reduce inrush current on start
ARM: dts: imx: Fix the AR803X phy-mode
ARM: dts: sun8i: a33: Reintroduce default pinctrl muxing
arm64: dts: allwinner: a64: Rename hpvcc-supply to cpvdd-supply
ARM: sunxi: fix a leaked reference by adding missing of_node_put
ARM: sunxi: fix a leaked reference by adding missing of_node_put
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Pull crypto fixes from Herbert Xu:
"This fixes a number of issues in the chelsio and caam drivers"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
Revert "crypto: caam/jr - Remove extra memory barrier during job ring dequeue"
crypto: caam - fix caam_dump_sg that iterates through scatterlist
crypto: caam - fix DKP detection logic
MAINTAINERS: Maintainer for Chelsio crypto driver
crypto: chelsio - count incomplete block in IV
crypto: chelsio - Fix softlockup with heavy I/O
crypto: chelsio - Fix NULL pointer dereference
|
|
This reverts commit bbfcac5ff5f26aafa51935a62eb86b6eacfe8a49.
It caused a crash regression on powerpc:
https://lore.kernel.org/linux-crypto/87pnp2aflz.fsf@concordia.ellerman.id.au/
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Fix caam_dump_sg by correctly determining the next scatterlist
entry in the list.
Fixes: 5ecf8ef9103c ("crypto: caam - fix sg dump")
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The detection for DKP (Derived Key Protocol) relied on the value
of the setkey function. This was broken by the recent change which
added des3_aead_setkey.
This patch fixes this by introducing a new flag for DKP and setting
that where needed.
Fixes: 1b52c40919e6 ("crypto: caam - Forbid 2-key 3DES in FIPS mode")
Reported-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The partial block should count as one and appropriately appended
to IV. eg 499B for AES CTR should count 32 block than 31 and
correct count value is updated in iv out.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
removed un-necessary lock_chcr_dev to protect device state
DETACH. lock is not required to protect I/O count
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Do not request FW to generate cidx update if there is less
space in tx queue to post new request.
SGE DBP 1 pidx increment too large
BUG: unable to handle kernel NULL pointer dereference at
0000000000000124
SGE error for queue 101
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Pull crypto update from Herbert Xu:
"API:
- Add support for AEAD in simd
- Add fuzz testing to testmgr
- Add panic_on_fail module parameter to testmgr
- Use per-CPU struct instead multiple variables in scompress
- Change verify API for akcipher
Algorithms:
- Convert x86 AEAD algorithms over to simd
- Forbid 2-key 3DES in FIPS mode
- Add EC-RDSA (GOST 34.10) algorithm
Drivers:
- Set output IV with ctr-aes in crypto4xx
- Set output IV in rockchip
- Fix potential length overflow with hashing in sun4i-ss
- Fix computation error with ctr in vmx
- Add SM4 protected keys support in ccree
- Remove long-broken mxc-scc driver
- Add rfc4106(gcm(aes)) cipher support in cavium/nitrox"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (179 commits)
crypto: ccree - use a proper le32 type for le32 val
crypto: ccree - remove set but not used variable 'du_size'
crypto: ccree - Make cc_sec_disable static
crypto: ccree - fix spelling mistake "protedcted" -> "protected"
crypto: caam/qi2 - generate hash keys in-place
crypto: caam/qi2 - fix DMA mapping of stack memory
crypto: caam/qi2 - fix zero-length buffer DMA mapping
crypto: stm32/cryp - update to return iv_out
crypto: stm32/cryp - remove request mutex protection
crypto: stm32/cryp - add weak key check for DES
crypto: atmel - remove set but not used variable 'alg_name'
crypto: picoxcell - Use dev_get_drvdata()
crypto: crypto4xx - get rid of redundant using_sd variable
crypto: crypto4xx - use sync skcipher for fallback
crypto: crypto4xx - fix cfb and ofb "overran dst buffer" issues
crypto: crypto4xx - fix ctr-aes missing output IV
crypto: ecrdsa - select ASN1 and OID_REGISTRY for EC-RDSA
crypto: ux500 - use ccflags-y instead of CFLAGS_<basename>.o
crypto: ccree - handle tee fips error during power management resume
crypto: ccree - add function to handle cryptocell tee fips error
...
|
|
Pull mmiowb removal from Will Deacon:
"Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb())
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
The only relatively recent changes have been addressing review
comments on the documentation, which is in a much better shape thanks
to the efforts of Ben and Ingo.
I was initially planning to split this into two pull requests so that
you could run the coccinelle script yourself, however it's been plain
sailing in linux-next so I've just included the whole lot here to keep
things simple"
* tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (23 commits)
docs/memory-barriers.txt: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt: Fix style, spacing and grammar in I/O section
arch: Remove dummy mmiowb() definitions from arch code
net/ethernet/silan/sc92031: Remove stale comment about mmiowb()
i40iw: Redefine i40iw_mmiowb() to do nothing
scsi/qla1280: Remove stale comment about mmiowb()
drivers: Remove explicit invocations of mmiowb()
drivers: Remove useless trailing comments from mmiowb() invocations
Documentation: Kill all references to mmiowb()
riscv/mmiowb: Hook up mmwiob() implementation to asm-generic code
powerpc/mmiowb: Hook up mmwiob() implementation to asm-generic code
ia64/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
mips/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
sh/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
m68k/io: Remove useless definition of mmiowb()
nds32/io: Remove useless definition of mmiowb()
x86/io: Remove useless definition of mmiowb()
arm64/io: Remove useless definition of mmiowb()
ARM/io: Remove useless definition of mmiowb()
mmiowb: Hook up mmiowb helpers to spinlocks and generic I/O accessors
...
|
|
We build an explicit little endian value from the IDR register
values. Use a proper le32 type to mark the var as such to
satisfy Sparse.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: dcf6285d18ea1 ("crypto: ccree - add CID and PID support")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/crypto/ccree/cc_cipher.c: In function cc_setup_key_desc:
drivers/crypto/ccree/cc_cipher.c:645:15: warning: variable du_size set but not used [-Wunused-but-set-variable]
It is never used since introduction in
commit dd8486c75085 ("crypto: ccree - move key load desc. before flow desc.")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Fix sparse warning:
drivers/crypto/ccree/cc_driver.c:37:6: warning:
symbol 'cc_sec_disable' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
There is a spelling mistake in a dev_dbg message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-By: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Commit 307244452d3d ("crypto: caam - generate hash keys in-place")
fixed ahash implementation in caam/jr driver such that user-provided key
buffer is not DMA mapped, since it's not guaranteed to be DMAable.
Apply a similar fix for caam/qi2 driver.
Cc: <stable@vger.kernel.org> # v4.20+
Fixes: 3f16f6c9d632 ("crypto: caam/qi2 - add support for ahash algorithms")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Commits c19650d6ea99 ("crypto: caam - fix DMA mapping of stack memory")
and 65055e210884 ("crypto: caam - fix hash context DMA unmap size")
fixed the ahash implementation in caam/jr driver such that req->result
is not DMA-mapped (since it's not guaranteed to be DMA-able).
Apply a similar fix for ahash implementation in caam/qi2 driver.
Cc: <stable@vger.kernel.org> # v4.20+
Fixes: 3f16f6c9d632 ("crypto: caam/qi2 - add support for ahash algorithms")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Commit 04e6d25c5bb2 ("crypto: caam - fix zero-length buffer DMA mapping")
fixed an issue in caam/jr driver where ahash implementation was
DMA mapping a zero-length buffer.
Current commit applies a similar fix for caam/qi2 driver.
Cc: <stable@vger.kernel.org> # v4.20+
Fixes: 3f16f6c9d632 ("crypto: caam/qi2 - add support for ahash algorithms")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The kernel crypto API request output the next IV data to
IV buffer for CBC implementation.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Mutex is badly used between threaded irq and driver.
This mutex must be removed as the framework must ensure
that requests must be serialized to avoid issue. Rework
req to avoid crash during finalize by fixing the NULL
pointer issue.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add weak key test for des functions calling the generic
des_ekey.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/crypto/atmel-tdes.c: In function 'atmel_tdes_setkey':
drivers/crypto/atmel-tdes.c:803:14: warning: variable 'alg_name' set but not used [-Wunused-but-set-variable]
It is not used any more since
commit 52ea3cd2917b ("crypto: atmel - Forbid 2-key 3DES in FIPS mode")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Using dev_get_drvdata directly.
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
using_sd is used as a stand-in for sa_command_0.bf.scatter
that we need to set anyway, so we might as well just prevent
double-accounting.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This replaces struct crypto_skcipher and the extra request size
with struct crypto_sync_skcipher and SYNC_SKCIPHER_REQUEST_ON_STACK(),
which uses a fixed stack size.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
Hook, Gary
Horia Geantă
Giovanni Cabiddu
Shant KumarX Sonnad
Xin Zeng
Linus Torvalds
Thomas Gleixner
Daniel Axtens
Iuliana Prodan
Olof Johansson
Herbert Xu
Atul Gupta
Gilad Ben-Yossef
YueHaibing
Colin Ian King
Lionel Debieve
Kefeng Wang
Christian Lamparter