| Age | Commit message (Collapse) | Author | Files | Lines | |
|---|---|---|---|---|---|
| 2015-08-10 | extcon: palmas: Support GPIO based USB ID detection |   Roger Quadros | 1 | -0/+1 | |
| Some palmas based chip variants do not have OTG based ID logic. For these variants we rely on GPIO based USB ID detection. These chips do have VBUS comparator for VBUS detection so we continue to use the old way of detecting VBUS. Signed-off-by: Roger Quadros <rogerq@ti.com> Acked-by: Chanwoo Choi <cw00.choi@samsung.com> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> | |||||
| 2015-06-12 | extcon: Redefine the unique id of supported external connectors without 'enum extcon' type |   Chanwoo Choi | 1 | -1/+1 | |
| This patch just redefine the unique id of supported external connectors without 'enum extcon' type. Because unique id would be used on devictree file(*.dts) to indicate the specific external connectors like key number of input framework. So, I have the plan to move this definitions to following header file which includes the unique id of supported external connectors. - include/dt-bindings/extcon/extcon.h Fixes: 2a9de9c0f08d ("extcon: Use the unique id for external connector instead of string") Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2015-05-22 | extcon: Use the unique id for external connector instead of string | Chanwoo Choi | 1 | -24/+8 | |
| This patch uses the unique id to identify the type of external connector instead of string name. The string name have the many potential issues. So, this patch defines the 'extcon' enumeration which includes all supported external connector on EXTCON subsystem. If new external connector is necessary, the unique id of new connector have to be added in 'extcon' enumeration. There are current supported external connector in 'enum extcon' as following: enum extcon { EXTCON_NONE = 0x0, /* USB external connector */ EXTCON_USB = 0x1, EXTCON_USB_HOST = 0x2, /* Charger external connector */ EXTCON_TA = 0x10, EXTCON_FAST_CHARGER = 0x11, EXTCON_SLOW_CHARGER = 0x12, EXTCON_CHARGE_DOWNSTREAM = 0x13, /* Audio and video external connector */ EXTCON_LINE_IN = 0x20, EXTCON_LINE_OUT = 0x21, EXTCON_MICROPHONE = 0x22, EXTCON_HEADPHONE = 0x23, EXTCON_HDMI = 0x30, EXTCON_MHL = 0x31, EXTCON_DVI = 0x32, EXTCON_VGA = 0x33, EXTCON_SPDIF_IN = 0x34, EXTCON_SPDIF_OUT = 0x35, EXTCON_VIDEO_IN = 0x36, EXTCON_VIDEO_OUT = 0x37, /* Miscellaneous external connector */ EXTCON_DOCK = 0x50, EXTCON_JIG = 0x51, EXTCON_MECHANICAL = 0x52, EXTCON_END, }; For example in extcon-arizona.c: To use unique id removes the potential issue about handling the inconsistent name of external connector with string. - Previously, use the string to register the type of arizona jack connector static const char *arizona_cable[] = { "Mechanical", "Microphone", "Headphone", "Line-out", }; - Newly, use the unique id to register the type of arizona jack connector static const enum extcon arizona_cable[] = { EXTCON_MECHANICAL, EXTCON_MICROPHONE, EXTCON_HEADPHONE, EXTCON_LINE_OUT, EXTCON_NONE, }; And this patch modify the prototype of extcon_{get|set}_cable_state_() which uses the 'enum extcon id' instead of 'cable_index'. Because although one more extcon drivers support USB cable, each extcon driver might has the differnt 'cable_index' for USB cable. All extcon drivers can use the unique id number for same external connector with modified extcon_{get|set}_cable_state_(). - Previously, use 'cable_index' on these functions: extcon_get_cable_state_(struct extcon_dev*, int cable_index) extcon_set_cable_state_(struct extcon_dev*, int cable_index, bool state) -Newly, use 'enum extcon id' on these functions: extcon_get_cable_state_(struct extcon_dev*, enum extcon id) extcon_set_cable_state_(struct extcon_dev*, enum extcon id, bool state) Cc: Arnd Bergmann <arnd@arndb.de> Cc: Felipe Balbi <balbi@ti.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Acked-by: Roger Quadros <rogerq@ti.com> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Acked-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> [arnd: Report the build break about drivers/usb/phy/phy-tahvo.c after using the unique id for external connector insteadf of string] Reported-by: Arnd Bergmann <arnd@arndb.de> [dan.carpenter: Report the build warning of extcon_{set|get}_cable_state_()] Reported-by: Dan Carpenter <dan.carpenter@oracle.com> | |||||
| 2015-05-20 | extcon: usb-gpio: use flags argument of devm_gpiod_get to set direction |   Uwe Kleine-König | 1 | -1/+1 | |
| Since 39b2bbe3d715 (gpio: add flags argument to gpiod_get*() functions) which appeared in v3.17-rc1, the gpiod_get* functions take an additional parameter that allows to specify direction and initial value for output. Without this patch there is no call to gpiod_direction_input but the gpio is used for irq reporting and for that the line should be in input mode. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> | |||||
| 2015-05-19 | extcon: Allow compile test of GPIO consumers if !GPIOLIB |   Geert Uytterhoeven | 1 | -0/+1 | |
| The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer functionality only, can still be compiled if GPIOLIB is not enabled. Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where appropriate. If GPIOLIB=n and asm-generic/gpio.h is not used: drivers/extcon/extcon-usb-gpio.c: In function ‘usb_extcon_detect_cable’: drivers/extcon/extcon-usb-gpio.c:63: error: implicit declaration of function ‘gpiod_get_value_cansleep’ drivers/extcon/extcon-usb-gpio.c: In function ‘usb_extcon_probe’: drivers/extcon/extcon-usb-gpio.c:116: error: implicit declaration of function ‘devm_gpiod_get’ drivers/extcon/extcon-usb-gpio.c:116: warning: assignment makes pointer from integer without a cast drivers/extcon/extcon-usb-gpio.c:122: error: implicit declaration of function ‘gpiod_set_debounce’ drivers/extcon/extcon-usb-gpio.c:129: error: implicit declaration of function ‘gpiod_to_irq’ Add the missing #include <linux/gpio/consumer.h> to fix this. Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> | |||||
| 2015-04-27 | extcon: usb-gpio: register extcon device before IRQ registration |   Robert Baldyga | 1 | -12/+12 | |
| IRQ handler touches info->edev, so if interrupt occurs before extcon device initialization it can cause NULL pointer dereference. Doing extcon initialization before IRQ handler registration fixes this problem. Signed-off-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> | |||||
| 2015-03-07 | extcon: Fix the checkpatch warning | Chanwoo Choi | 1 | -1/+1 | |
| This patch fixes the checkpatch warning about coding style. Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> | |||||
| 2015-02-24 | extcon: usb-gpio: Introduce gpio usb extcon driver | Roger Quadros | 1 | -0/+237 | |
| This driver observes the USB ID pin connected over a GPIO and updates the USB cable extcon states accordingly. The existing GPIO extcon driver is not suitable for this purpose as it needs to be taught to understand USB cable states and it can't handle more than one cable per instance. For the USB case we need to handle 2 cable states. 1) USB (attach/detach) 2) USB-HOST (attach/detach) This driver can be easily updated in the future to handle VBUS events in case it happens to be available on GPIO for any platform. Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> | |||||
 |
index : linux-dev | |
| Linux kernel development work - see feature branches | Jason A. Donenfeld |
| aboutsummaryrefslogtreecommitdiffstats |