| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This driver clearly needs OF_GPIO so depend on it.
Fixes a build error.
Cc: Andrei Stefanescu <Andrei.Stefanescu@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds a driver for Cadence GPIO controller.
It can be enabled with GPIO_CADENCE Kconfig option.
It uses generic GPIO infrastructure and works
as an interrupt controller.
At the moment it only supports level sensitive irqs.
Signed-off-by: Jan Kotas <jank@cadence.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
PIOBU pins do not lose their voltage during Backup/Self-refresh.
This patch adds a simple GPIO controller for them and a
maintainer for the driver.
This driver adds support for using the pins as GPIO
offering the possibility to read/set the voltage.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Select REGMAP_I2C in Kconfig, since the driver now depends on regmap
and this was missing, thus breaking build on various systems.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The change adds support of LPC18xx/LPC43xx GPIO pin interrupt controller
block within SoC GPIO controller. The new interrupt controller driver
allows to configure and capture edge or level interrupts on 8 arbitrary
selectedinput GPIO pins, and lift the signals to be reported as NVIC rising
edge interrupts. Configuration of a particular GPIO pin to serve as
interrupt and its mapping to an interrupt on NVIC is done by SCU pin
controller, for more details see description of 'nxp,gpio-pin-interrupt'
device tree property of a GPIO pin [1].
From LPC18xx and LPC43xx User Manuals the GPIO controller consists of
the following blocks:
* GPIO pin interrupt block at 0x40087000, this change adds its support,
* GPIO GROUP0 interrupt block at 0x40088000,
* GPIO GROUP1 interrupt block at 0x40089000,
* GPIO port block at 0x400F4000, it is supported by the original driver.
While all 4 sub-controller blocks have their own I/O addresses, moreover
all 3 interrupt blocks are APB0 peripherals and high-speed GPIO block is
an AHB slave, according to the hardware manual the GPIO controller is
seen as a single block, and 4 sub-controllers have the shared reset signal
RGU #28 and clock to register interface CLK_CPU_GPIO on CCU1.
Likely support of two GPIO group interrupt blocks won't be added in short
term, because the mechanism to mask several interrupt sources is not well
defined.
[1] Documentation/devicetree/bindings/pinctrl/nxp,lpc1850-scu.txt
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix kconfig warning for GPIO_SNPS_CREG:
WARNING: unmet direct dependencies detected for OF_GPIO
Depends on [n]: GPIOLIB [=y] && OF [=n] && HAS_IOMEM [=y]
Selected by [y]:
- GPIO_SNPS_CREG [=y] && GPIOLIB [=y] && HAS_IOMEM [=y] && (ARC || COMPILE_TEST [=y])
Drivers in drivers/gpio/Kconfig depend on OF_GPIO, not select it.
This prevents attempting to build when OF is not enabled.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add single-register MMIO GPIO driver for complex cases where
only several fields in register belong to GPIO lines and each GPIO
line owns a field with different length and on/off value.
Such CREG GPIOs are used in Synopsys AXS10x and HSDK boards.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This driver controls a SIOX device that provides 20 I/O lines. The first
twelve are fixed inputs, the remaining eight are outputs.
Acked-by: Gavin Schenk <g.schenk@eckelmann.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
The pinctrl-ingenic driver is now handling the GPIO chips directly.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We can quite easily switch banks/ports A and B to use
GPIOLIB_IRQCHIP which is code that will be more careful
about handling interrupt descriptors and use a proper
irqdomain for translating the IRQs. This cuts down some
code in favor of using the implementation inside
gpiolib.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Instead of open coding logic for reading and writing GPIO lines,
use the generic GPIO library. Also switch to using the spinlock
from the generic GPIO to protect the registers.
Cc: linux-snps-arc@lists.infradead.org
Acked-by: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Pull MFD updates from Lee Jones:
"New Drivers:
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
New Device Support:
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
New Functionality:
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
Fix-upsL
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
Bug Fixes:
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501"
* tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (60 commits)
mfd: madera: Add register definitions for accessory detect
mfd: sm501: Set coherent_dma_mask when creating subdevices
mfd: bd71837: Devicetree bindings for ROHM BD71837 PMIC
mfd: bd71837: Core driver for ROHM BD71837 PMIC
media: platform: cros-ec-cec: Fix dependency on MFD_CROS_EC
mfd: sec-core: Export OF module alias table
mfd: as3722: Disable auto-power-on when AC OK
mfd: axp20x: Support AXP806 in I2C mode
mfd: axp20x: Add self-working mode support for AXP806
dt-bindings: mfd: axp20x: Add "self-working" mode for AXP806
mfd: wm8994: Allow to configure CS/ADDR Pulldown from dts
mfd: wm8994: Allow to configure Speaker Mode Pullup from dts
mfd: rave-sp: Emulate CMD_GET_STATUS on device that don't support it
mfd: rave-sp: Add legacy watchdog ping command translation
mfd: rave-sp: Add legacy EEPROM access command translation
mfd: rave-sp: Initialize flow control and parity of the port
mfd: rave-sp: Fix incorrectly specified checksum type
mfd: rave-sp: Remove unused defines
mfd: hi655x: Fix regmap area declared size for hi655x
mfd: ti_am335x_tscadc: Fix struct clk memory leak
...
|
|
This was tested on actual hardware and found to work fine, but currently
the official specifications of this chip could not be obtained to
confirm the numbers.
Signed-off-by: Leonid Bloch <lbloch@janustech.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Immutable branch (mfd, chrome) due for the v4.19 window
Immutable Branch which moves the cros_ec_i2c and cros_ec_spi
transport drivers from mfd to platform/chrome. Changes in arm are a simple
rename in defconfigs. Change in input is a rename in help text.
|
|
Compile-testing the driver fails unless OF_GPIO is enabled:
drivers/gpio/gpio-mt7621.c: In function 'mediatek_gpio_bank_probe':
drivers/gpio/gpio-mt7621.c:228:10: error: 'struct gpio_chip' has no member named 'of_node'
Fixes: 4ba9c3afda41 ("gpio: mt7621: Add a driver for MT7621")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add driver support for gpio of MT7621 SoC.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
[Switched wording WIDTH to STRIDE]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds support for the GPIOs on Cirrus Logic Madera class codecs.
Any pins not used for special functions (see the pinctrl driver) can be
used as general single-bit input or output lines. The number of available
GPIOs varies between codecs.
Note that this is part of a composite MFD for these codecs and can only
be used with the corresponding MFD and other child drivers on those
silicon. The GPIO block on these codecs does not exist indepedently of
the rest of the MFD.
Signed-off-by: Nariman Poushin <nariman@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The new challenge is to remove VLAs from the kernel
(see https://lkml.org/lkml/2018/3/7/621) to eventually
turn on -Wvla.
Using a kmalloc array is the easy way to fix this but kmalloc is still
more expensive than stack allocation. Introduce a fast path with a
fixed size stack array to cover most chip with gpios below some fixed
amount. The slow path dynamically allocates an array to cover those
chips with a large number of gpios.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Phil Reid <preid@electromag.com.au>
Reviewed-and-tested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.17 kernel cycle:
New drivers:
- Nintendo Wii GameCube GPIO, known as "Hollywood"
- Raspberry Pi mailbox service GPIO expander
- Spreadtrum main SC9860 SoC and IEC GPIO controllers.
Improvements:
- Implemented .get_multiple() callback for most of the
high-performance industrial GPIO cards for the ISA bus.
- ISA GPIO drivers now select the ISA_BUS_API instead of depending on
it. This is merged with the same pattern for all the ISA drivers
and some other Kconfig cleanups related to this.
Cleanup:
- Delete the TZ1090 GPIO drivers following the deletion of this SoC
from the ARM tree.
- Move the documentation over to driver-api to conform with the rest
of the kernel documentation build.
- Continue to make the GPIO drivers include only
<linux/gpio/driver.h> and not the too broad <linux/gpio.h> that we
want to get rid of.
- Managed to remove VLA allocation from two drivers pending more
fixes in this area for the next merge window.
- Misc janitorial fixes"
* tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
gpio: Add Spreadtrum PMIC EIC driver support
gpio: Add Spreadtrum EIC driver support
dt-bindings: gpio: Add Spreadtrum EIC controller documentation
gpio: ath79: Fix potential NULL dereference in ath79_gpio_probe()
pinctrl: qcom: Don't allow protected pins to be requested
gpiolib: Support 'gpio-reserved-ranges' property
gpiolib: Change bitmap allocation to kmalloc_array
gpiolib: Extract mask allocation into subroutine
dt-bindings: gpio: Add a gpio-reserved-ranges property
gpio: mockup: fix a potential crash when creating debugfs entries
gpio: pca953x: add compatibility for pcal6524 and pcal9555a
gpio: dwapb: Add support for a bus clock
gpio: Remove VLA from xra1403 driver
gpio: Remove VLA from MAX3191X driver
gpio: ws16c48: Implement get_multiple callback
gpio: gpio-mm: Implement get_multiple callback
gpio: 104-idi-48: Implement get_multiple callback
gpio: 104-dio-48e: Implement get_multiple callback
gpio: pcie-idio-24: Implement get_multiple/set_multiple callbacks
gpio: pci-idio-16: Implement get_multiple callback
...
|
|
The Spreadtrum PMIC EIC controller contains only one bank of debounce EIC,
and this bank contains 16 EICs. Each EIC can only be used as input mode,
as well as supporting the debounce and the capability to trigger interrupts
when detecting input signals.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Spreadtrum digital-chip EIC controller has 4 sub-modules: debounce EIC,
latch EIC, async EIC and sync EIC, and each sub-module can has multiple
banks and each bank contains 8 EICs.
Each EIC can only be used as input mode, and has the capability to trigger
interrupts when detecting input signals.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The cris architecture is getting removed, so we no longer need the
etraxfs driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Commit 7ed915059c3001 (gpio: raspberrypi-ext: fix firmware dependency)
fixed the Kconfig dependency to ensure that gpio-raspberrypi-exp is not
built-in when the firmware is a module. But the Kconfig syntax for doing
so is cryptic. Add a comment to make it a little easier.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Spreadtrum SC9860 platform GPIO controller contains 16 groups and
each group contains 16 GPIOs. Each GPIO can set input/output and has
the interrupt capability.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When the firmware driver is a loadable module, the gpio driver cannot be
built-in:
drivers/gpio/gpio-raspberrypi-exp.o: In function `rpi_exp_gpio_set':
gpio-raspberrypi-exp.c:(.text+0xb4): undefined reference to `rpi_firmware_property'
drivers/gpio/gpio-raspberrypi-exp.o: In function `rpi_exp_gpio_get':
gpio-raspberrypi-exp.c:(.text+0x1ec): undefined reference to `rpi_firmware_property'
drivers/gpio/gpio-raspberrypi-exp.o: In function `rpi_exp_gpio_get_direction':
gpio-raspberrypi-exp.c:(.text+0x360): undefined reference to `rpi_firmware_property'
drivers/gpio/gpio-raspberrypi-exp.o: In function `rpi_exp_gpio_get_polarity':
gpio-raspberrypi-exp.c:(.text+0x4d4): undefined reference to `rpi_firmware_property'
drivers/gpio/gpio-raspberrypi-exp.o: In function `rpi_exp_gpio_dir_out':
gpio-raspberrypi-exp.c:(.text+0x670): undefined reference to `rpi_firmware_property'
drivers/gpio/gpio-raspberrypi-exp.o:gpio-raspberrypi-exp.c:(.text+0x7fc): more undefined references to `rpi_firmware_property' follow
drivers/gpio/gpio-raspberrypi-exp.o: In function `rpi_exp_gpio_dir_in':
drivers/gpio/gpio-raspberrypi-exp.o: In function `rpi_exp_gpio_probe':
gpio-raspberrypi-exp.c:(.text+0x93c): undefined reference to `rpi_firmware_get'
We already have a Kconfig dependency for it, but when compile-testing, it
is disregarded.
This changes the dependency so that compile-testing is only done when the
firmware driver is completely disabled.
Fixes: a98d90e7d588 ("gpio: raspberrypi-exp: Driver for RPi3 GPIO expander via mailbox service")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Now that arch/metag/ has been removed, along with TZ1090 SoC support,
remove the TZ1090 GPIO drivers. They are of no value without the
architecture and SoC platform code.
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-metag@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This reverts commit 92a8046c9d952a2a7d21dfcd3afadc72a0bc0f72.
Now that the patch series changing ISA_BUS_API dependency to selection
was merged this reversion will do the same for gpio-winbond driver to
make it consistent with other ISA bus gpio drivers.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The ISA_BUS_API Kconfig option enables the compilation of the ISA bus
driver. The ISA bus driver does not perform any hardware interaction,
and is instead just a thin layer of software abstraction to eliminate
boilerplate code common to ISA-style device drivers. Since ISA_BUS_API
has no dependencies and does not jeopardize the integrity of the system
when enabled, drivers should select it when the ISA bus driver
functionality is needed.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Nintendo Wii's chipset (called "Hollywood") has a GPIO controller
that supports a configurable number of pins (up to 32), interrupts, and
some special mechanisms to share the controller between the system's
security processor (an ARM926) and the PowerPC CPU. Pin multiplexing is
not supported.
This patch adds a basic driver for this GPIO controller. Interrupt
support will come in a later patch.
This patch is based on code developed by Albert Herranz and the GameCube
Linux Team, file arch/powerpc/platforms/embedded6xx/hlwd-gpio.c,
available at https://github.com/DeltaResero/GC-Wii-Linux-Kernels, but
has grown quite dissimilar.
v3:
- Do some style cleanups, as suggest by Andy Shevchenko
v2:
- Change hlwd_gpio_driver.driver.name to "gpio-hlwd" to match the
filename (was "hlwd_gpio")
- Remove unnecessary include of linux/of_gpio.h, as suggested by Linus
Walleij.
- Add struct device pointer to context struct to make it possible to use
dev_info(hlwd->dev, "..."), as suggested by Linus Walleij
- Use the GPIO_GENERIC library to reduce code size, as suggested by
Linus Walleij
- Use iowrite32be instead of __raw_writel for big-endian MMIO access, as
suggested by Linus Walleij
- Remove commit message paragraph suggesting to diff against the
original driver, because it's so different now
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Cc: Albert Herranz <albert_herranz@yahoo.es>
Reviewed-by: Segher Boessenkool <segher@kernel.crashing.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Pi3 and Compute Module 3 have a GPIO expander that the
VPU communicates with.
There is a mailbox service that now allows control of this
expander, so add a kernel driver that can make use of it.
Reviewed-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The newly added GPIO driver for winbond chipsets causes a
circular dependency warning in Kconfig:
drivers/gpio/Kconfig:13:error: recursive dependency detected!
drivers/gpio/Kconfig:13: symbol GPIOLIB is selected by STX104
drivers/iio/adc/Kconfig:699: symbol STX104 depends on ISA_BUS_API
arch/Kconfig:830: symbol ISA_BUS_API is selected by GPIO_WINBOND
drivers/gpio/Kconfig:701: symbol GPIO_WINBOND depends on GPIOLIB
The underlying problem is that ISA_BUS_API is not meant to be selected by
device drivers, instead it is provided by the architectures that support
ISA add-on card devices, or in case of x86 have this explicitly enabled.
This particular driver appears to be different from the other ISA_BUS_API
based drivers, in that it is not normally an add-on card (ISA or PC104)
but instead is an LPC-attached component on the mainboard. We already
support other functionality provided by this chip, at least
drivers/watchdog/w83627hf_wdt.c and drivers/hwmon/w83627ehf.c, plus
there is a discovery function for this hardware in
drivers/parport/parport_pc.c.
If we want to use this driver without having to enable CONFIG_EXPERT,
it might be better to not use the isa_bus_type for it, but rather
turn it into a platform_driver, acpi_driver or add an MFD for it that
is shared with the wdt and hwmon portions and does the probing.
For now, this patch fixes the dependency by changing 'select' into
'depends on'.
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fixes: a0d65009411c ("gpio: winbond: Add driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines
of optically-isolated non-polarized digital inputs for AC and DC control
signals, 24 lines of isolated solid state FET digital outputs, and 8
non-isolated TTL/CMOS compatible programmable I/O). An interrupt is
generated when any of the inputs change state (low to high or high to
low).
Input filter control is not supported by this driver, and input filters
are deactivated by this driver. These devices are capable of
get_multiple and set_multiple functionality, but these functions have
not yet been implemented for this driver. Change-Of-State (COS)
detection functionality may be configured to fire interrupts on
exclusively rising/falling edges, but this driver currently only
implements COS detection for either both edges or none.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This commit adds GPIO driver for Winbond Super I/Os.
Currently, only W83627UHG model (also known as Nuvoton NCT6627UD)
is supported but in the future a support for other Winbond models,
too, can be added to the driver.
A module parameter "gpios" sets a bitmask of GPIO ports to enable
(bit 0 is GPIO1, bit 1 is GPIO2, etc.).
One should be careful which ports one tinkers with since some
might be managed by the firmware (for functions like powering on and
off, sleeping, BIOS recovery, etc.) and some of GPIO port pins are
physically shared with other devices included in the Super I/O chip.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
To prepare the driver for the upcoming pinctrl features, move the GPIO
driver AXP209 from GPIO to pinctrl subsystem.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.15 kernel cycle:
Core:
- The pin control Kconfig entry PINCTRL is now turned into a
menuconfig option. This obviously has the implication of making the
subsystem menu visible in menuconfig. This is happening because of
two things:
(a) Intel have started to deploy and depend on pin controllers in
a way that is affecting users directly. This happens on the
highly integrated laptop chipsets named after geographical
places: baytrail, broxton, cannonlake, cedarfork, cherryview,
denverton, geminilake, lewisburg, merrifield, sunrisepoint...
It started a while back and now it is ever more evident that
this is crucial infrastructure for x86 laptops and not an
embedded obscurity anymore. Users need to be aware.
(b) Pin control expanders on I2C and SPI that are arch-agnostic.
Currently Semtech SX150X and Microchip MCP28x08 but more are
expected. Users will have to be able to configure these in
directly for their set-up.
- Just go and select GPIOLIB now that we made sure that GPIOLIB is a
very vanilla subsystem. Do not depend on it, if we need it, select
it.
- Exposing the pin control subsystem in menuconfig uncovered a bunch
of obscure bugs that are now hopefully fixed, all more or less
pertaining to Blackfin.
- Unified namespace for cross-calls between pin control and GPIO.
- New support for clock skew/delay generic DT bindings and generic
pin config options for this.
- Minor documentation improvements.
Various:
- The Renesas SH-PFC pin controller has evolved a lot. It seems
Renesas are churning out new SoCs by the minute.
- A bunch of non-critical fixes for the Rockchip driver.
- Improve the use of library functions instead of open coding.
- Support the MCP28018 variant in the MCP28x08 driver.
- Static constifying"
* tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (91 commits)
pinctrl: gemini: Fix missing pad descriptions
pinctrl: Add some depends on HAS_IOMEM
pinctrl: samsung/s3c24xx: add CONFIG_OF dependency
pinctrl: gemini: Fix GMAC groups
pinctrl: qcom: spmi-gpio: Add pmi8994 gpio support
pinctrl: ti-iodelay: remove redundant unused variable dev
pinctrl: max77620: Use common error handling code in max77620_pinconf_set()
pinctrl: gemini: Implement clock skew/delay config
pinctrl: gemini: Use generic DT parser
pinctrl: Add skew-delay pin config and bindings
pinctrl: armada-37xx: Add edge both type gpio irq support
pinctrl: uniphier: remove eMMC hardware reset pin-mux
pinctrl: rockchip: Add iomux-route switching support for rk3288
pinctrl: intel: Add Intel Cedar Fork PCH pin controller support
pinctrl: intel: Make offset to interrupt status register configurable
pinctrl: sunxi: Enforce the strict mode by default
pinctrl: sunxi: Disable strict mode for old pinctrl drivers
pinctrl: sunxi: Introduce the strict flag
pinctrl: sh-pfc: Save/restore registers for PSCI system suspend
pinctrl: sh-pfc: r8a7796: Use generic IOCTRL register description
...
|
|
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.15 kernel cycle:
Core:
- Fix the semantics of raw GPIO to actually be raw. No inversion
semantics as before, but also no open draining, and allow the raw
operations to affect lines used for interrupts as the caller
supposedly knows what they are doing if they are getting the big
hammer.
- Rewrote the __inner_function() notation calls to names that make
more sense. I just find this kind of code disturbing.
- Drop the .irq_base() field from the gpiochip since now all IRQs are
mapped dynamically. This is nice.
- Support for .get_multiple() in the core driver API. This allows us
to read several GPIO lines with a single register read. This has
high value for some usecases: it can be used to create
oscilloscopes and signal analyzers and other things that rely on
reading several lines at exactly the same instant. Also a generally
nice optimization. This uses the new assign_bit() macro from the
bitops lib that was ACKed by Andrew Morton and is implemented for
two drivers, one of them being the generic MMIO driver so everyone
using that will be able to benefit from this.
- Do not allow requests of Open Drain and Open Source setting of a
GPIO line simultaneously. If the hardware actually supports
enabling both at the same time the electrical result would be
disastrous.
- A new interrupt chip core helper. This will be helpful to deal with
"banked" GPIOs, which means GPIO controllers with several logical
blocks of GPIO inside them. This is several gpiochips per device in
the device model, in contrast to the case when there is a 1-to-1
relationship between a device and a gpiochip.
New drivers:
- Maxim MAX3191x industrial serializer, a very interesting piece of
professional I/O hardware.
- Uniphier GPIO driver. This is the GPIO block from the recent
Socionext (ex Fujitsu and Panasonic) platform.
- Tegra 186 driver. This is based on the new banked GPIO
infrastructure.
Other improvements:
- Some documentation improvements.
- Wakeup support for the DesignWare DWAPB GPIO controller.
- Reset line support on the DesignWare DWAPB GPIO controller.
- Several non-critical bug fixes and improvements for the Broadcom
BRCMSTB driver.
- Misc non-critical bug fixes like exotic errorpaths, removal of dead
code etc.
- Explicit comments on fall-through switch() statements"
* tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (65 commits)
gpio: tegra186: Remove tegra186_gpio_lock_class
gpio: rcar: Add r8a77995 (R-Car D3) support
pinctrl: bcm2835: Fix some merge fallout
gpio: Fix undefined lock_dep_class
gpio: Automatically add lockdep keys
gpio: Introduce struct gpio_irq_chip.first
gpio: Disambiguate struct gpio_irq_chip.nested
gpio: Add Tegra186 support
gpio: Export gpiochip_irq_{map,unmap}()
gpio: Implement tighter IRQ chip integration
gpio: Move lock_key into struct gpio_irq_chip
gpio: Move irq_valid_mask into struct gpio_irq_chip
gpio: Move irq_nested into struct gpio_irq_chip
gpio: Move irq_chained_parent to struct gpio_irq_chip
gpio: Move irq_default_type to struct gpio_irq_chip
gpio: Move irq_handler to struct gpio_irq_chip
gpio: Move irqdomain into struct gpio_irq_chip
gpio: Move irqchip into struct gpio_irq_chip
gpio: Introduce struct gpio_irq_chip
pinctrl: armada-37xx: remove unused variable
...
|
|
|
|
Tegra186 has two GPIO controllers that are largely register compatible
between one another but are completely different from the controller
found on earlier generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In order to reuse this driver for the Socionext Synquacer SC2A11 SoC,
which inherited this IP from Fujitsu, remove the ARCH_MB86S7X Kconfig
dependency, and revert the changes that prevent it from being built as
a module.
This reverts commits d65aa4b67b4f47f303bdeaef1e4d42ef18e6b293 and
d5610e514e92144d19bd5e39e5cf3804bbf85f3e.
Cc: Geliang Tang <geliangtang@gmail.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[Folded in module_platform_driver() fixup]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The GPIOLIB IRQ chip helpers were very appealing, but badly broke
the 1:1 mapping between a GPIO controller's device_node and its
interrupt domain.
When another device-tree node references a GPIO device as its
interrupt parent, the irq_create_of_mapping() function looks for
the irq domain of the GPIO device and since all bank irq domains
reference the same GPIO device node it always resolves to the irq
domain of the first bank regardless of which bank the number of
the GPIO should resolve. This domain can only map hwirq numbers
0-31 so interrupts on GPIO above that can't be mapped by the
device-tree.
This commit effectively reverts the patch from Gregory Fong [1]
that was accepted upstream and replaces it with a consolidated
irq domain implementation with one larger interrupt domain per
GPIO controller instance spanning multiple GPIO banks based on
an earlier patch [2] also submitted by Gregory Fong.
[1] https://patchwork.kernel.org/patch/6921561/
[2] https://patchwork.kernel.org/patch/6347811/
Fixes: 19a7b6940b78 ("gpio: brcmstb: Add interrupt and wakeup source support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Gregory Fong <gregory.0xf0@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This GPIO controller is used on UniPhier SoC family.
It also serves as an interrupt controller, but interrupt signals are
just delivered to the parent irqchip without any latching or OR'ing.
This type of hardware can be well described with hierarchy IRQ domain.
One unfortunate thing for this device is that the interrupt mapping to
the interrupt parent is not contiguous.
I asked how DT can describe interrupt mapping between two irqchips [1],
but I could not find a good solution (at least in the framework level).
In fact, irqchip drivers using hierarchy domain generally hard-code the
DT binding of their parent.
After tackling on several approaches such as hard-code of hwirqs,
irq_domain_push_irq(), I ended up with a vendor specific property.
If we come up with a good idea to support this in the framework, we
can migrate over to it, but we can live with a driver-level solution
for now.
[1] https://lkml.org/lkml/2017/7/6/758
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The driver was developed for and tested with the MAX31913 built into
the Revolution Pi by KUNBUS, but should work with all members of the
MAX3191x family:
MAX31910: low power
MAX31911: LED drivers
MAX31912: LED drivers + 2nd voltage monitor + low power
MAX31913: LED drivers + 2nd voltage monitor
MAX31953: LED drivers + 2nd voltage monitor + isolation
MAX31963: LED drivers + 2nd voltage monitor + isolation + buck regulator
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The SX150X driver was moved over to pin control a while back.
The GPIO Kconfig symbol creates a circular dependency since
it requires GPIOLIB and the pin control driver selects GPIOLIB
so get rid of the old annoying Kconfig option.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
IRQ_DOMAIN_HIERARCHY is not user-configurable, but supposed to be
selected by drivers that need IRQ domain hierarchy support.
GPIO_THUNDERX is the only user of "depends on IRQ_DOMAIN_HIERARCHY".
This means, we can not enable GPIO_THUNDERX unless other drivers
select IRQ_DOMAIN_HIERARCHY elsewhere. This is odd. Flip the logic.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Cavium ThunderX and OCTEON-TX are arm64 based SoCs. Add driver for
the on-chip GPIO pins.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Shrink the driver by removing the code dealing with dummy interrupts
and replacing it with calls to the irq_sim API.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds support for TPS68470 GPIOs.
There are 7 GPIOs and a few sensor related GPIOs.
These GPIOs can be requested and configured as
appropriate.
The GPIOs are also provided with descriptive names.
However, the typical use case is that the OS GPIO
driver will interact with TPS68470 GPIO driver
to configure these GPIOs, as requested by the
platform firmware.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This driver calls irq_domain_hierarchy() and irq_chip_*_parent().
They are available only when CONFIG_IRQ_DOMAIN_HIERARCHY is enabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.13 series.
Some administrativa:
I have a slew of 8250 serial patches and the new IOT2040 serial+GPIO
driver coming in through this tree, along with a whole bunch of Exar
8250 fixes. These are ACKed by Greg and also hit drivers/platform/*
where they are ACKed by Andy Shevchenko.
Speaking about drivers/platform/* there is also a bunch of ACPI stuff
coming through that route, again ACKed by Andy.
The MCP23S08 changes are coming in here as well. You already have the
commits in your tree, so this is just a result of sharing an immutable
branch between pin control and GPIO.
Core:
- Export add/remove for lookup tables so that modules can export GPIO
descriptor tables.
- Handle GPIO sleep states: it is now possible to flag that a GPIO
line may loose its state during suspend/resume of the system to
save power. This is used in the Wolfson Micro Arizona driver.
- ACPI-based GPIO was tightened up a lot around the edges.
- Use bitmap_fill() to speed up a loop.
New drivers:
- Exar XRA1403 SPI-based GPIO.
- MVEBU driver now supports Armada 7K and 8K.
- LP87565 PMIC GPIO.
- Renesas R-CAR R8A7743 (RZ/G1M).
- The new IOT2040 8250 serial/GPIO also comes in through this
changeset.
Substantial driver changes:
- Seriously fix the Exar 8250 GPIO portions to work.
- The MCP23S08 was moved out to a pin control driver.
- Convert MEVEBU to use regmap for register access.
- Drop Vulcan support from the Broadcom driver.
- Serious cleanup and improvement of the mockup driver, giving us a
better test coverage.
Misc:
- Lots of janitorial clean up.
- A bunch of documentation fixes"
* tag 'gpio-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (70 commits)
serial: exar: Add support for IOT2040 device
gpio-exar/8250-exar: Make set of exported GPIOs configurable
platform: Accept const properties
serial: exar: Factor out platform hooks
gpio-exar/8250-exar: Rearrange gpiochip parenthood
gpio: exar: Fix iomap request
gpio-exar/8250-exar: Do not even instantiate a GPIO device for Commtech cards
serial: uapi: Add support for bus termination
gpio: rcar: Add R8A7743 (RZ/G1M) support
gpio: gpio-wcove: Fix GPIO control register offset calculation
gpio: lp87565: Add support for GPIO
gpio: dwapb: fix missing first irq for edgeboth irq type
MAINTAINERS: Take maintainership for GPIO ACPI support
gpio: exar: Fix reading of directions and values
gpio: exar: Allocate resources on behalf of the platform device
gpio-exar/8250-exar: Fix passing in of parent PCI device
gpio: mockup: use devm_kcalloc() where applicable
gpio: mockup: add myself as author
gpio: mockup: improve the error message
gpio: mockup: don't return magic numbers from probe()
...
|
Linus Walleij
Jan Kotas
Andrei.Stefanescu@microchip.com
Marek Vasut
Vladimir Zapolskiy
Randy Dunlap
Eugeniy Paltsev
Uwe Kleine-König
Paul Cercueil
Linus Torvalds
Leonid Bloch
Lee Jones
Arnd Bergmann
Sergio Paracuellos
Richard Fitzgerald
Laura Abbott
Baolin Wang
Baruch Siach
James Hogan
Maciej S. Szmigiero
William Breathitt Gray
Jonathan Neuschäfer
Dave Stevenson
Quentin Schulz
Thierry Reding
Ard Biesheuvel
Doug Berger
Masahiro Yamada
Lukas Wunner
David Daney
Bartosz Golaszewski
Rajmohan Mani