Age | Commit message (Collapse) | Author | Files | Lines |
|
This interface is for dGPU Navi1x. Linux dc-pplib interface depends
on window driver dc implementation.
For Navi1x, clock settings of dcn watermarks are fixed. the settings
should be passed to smu during boot up and resume from s3.
boot up: dc calculate dcn watermark clock settings within dc_create,
dcn20_resource_construct, then call pplib functions below to pass
the settings to smu:
smu_set_watermarks_for_clock_ranges
smu_set_watermarks_table
navi10_set_watermarks_table
smu_write_watermarks_table
For Renoir, clock settings of dcn watermark are also fixed values.
dc has implemented different flow for window driver:
dc_hardware_init / dc_set_power_state
dcn10_init_hw
notify_wm_ranges
set_wm_ranges
For Linux
smu_set_watermarks_for_clock_ranges
renoir_set_watermarks_table
smu_write_watermarks_table
dc_hardware_init -> amdgpu_dm_init
dc_set_power_state --> dm_resume
therefore, linux dc-pplib interface of navi10/12/14 is different
from that of Renoir.
v2: add missing unlock in error case
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Swath sizes are being calculated incorrectly. The horizontal swath size
should be the product of block height, viewport width, and bytes per
element, but the calculation uses viewport height instead of width. The
vertical swath size is similarly incorrectly calculated. The effect of
this is that we report the wrong DCC caps.
[How]
Use viewport width in the horizontal swath size calculation and viewport
height in the vertical swath size calculation.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
If we have a single MST display and we disconnect it, we dont disable that
link. This causes the old link settings to still exist
Now on a replug for MST we think its a link loss and will try to reallocate
mst payload which will fail, throwing warning below.
[ 129.374192] [drm] Failed to updateMST allocation table forpipe idx:0
[ 129.374206] ------------[ cut here ]------------
[ 129.374284] WARNING: CPU: 14 PID: 1710 at
drivers/gpu/drm/amd/amdgpu/../dal-dev/dc/core/dc_link.c:3153
dc_link_allocate_mst_payload+0x1f7/0x220 [amdgpu]
[ 129.374285] Modules linked in: amdgpu(OE) amd_iommu_v2 gpu_sched ttm
drm_kms_helper drm fb_sys_fops syscopyarea sysfillrect sysimgblt
binfmt_misc nls_iso8859_1 edac_mce_amd snd_hda_codec_realtek
snd_hda_codec_generic ledtrig_audio kvm snd_hda_codec_hdmi snd_hda_intel
snd_intel_nhlt snd_hda_codec irqbypass snd_hda_core snd_hwdep snd_pcm
snd_seq_midi snd_seq_midi_event snd_rawmidi crct10dif_pclmul snd_seq
crc32_pclmul ghash_clmulni_intel snd_seq_device snd_timer snd aesni_intel
eeepc_wmi crypto_simd asus_wmi joydev cryptd sparse_keymap input_leds
soundcore video glue_helper wmi_bmof mxm_wmi k10temp ccp mac_hid
sch_fq_codel parport_pc ppdev lp parport ip_tables x_tables autofs4
hid_generic usbhid hid igb i2c_algo_bit ahci dca i2c_piix4 libahci
gpio_amdpt wmi gpio_generic
[ 129.374318] CPU: 14 PID: 1710 Comm: kworker/14:2 Tainted: G W OE 5.4.0-rc7bhawan+ #480
[ 129.374318] Hardware name: System manufacturer System Product Name/PRIME X370-PRO, BIOS 0515 03/30/2017
[ 129.374397] Workqueue: events dm_irq_work_func [amdgpu]
[ 129.374468] RIP: 0010:dc_link_allocate_mst_payload+0x1f7/0x220 [amdgpu]
[ 129.374470] Code: 52 20 e8 1c 63 ad f4 48 8b 5d d0 65 48 33 1c 25 28 00
00 00 b8 01 00 00 00 75 16 48 8d 65 d8 5b 41 5c 41 5d 41 5e 41 5f 5d c3
<0f> 0b e9 fa fe ff ff e8 ed 5b d6 f3 41 0f b6 b6 c4 02 00 00 48 c7
[ 129.374471] RSP: 0018:ffff9f9141e7fcc0 EFLAGS: 00010246
[ 129.374472] RAX: 0000000000000000 RBX: ffff91ef0762f800 RCX: 0000000000000000
[ 129.374473] RDX: 0000000000000005 RSI: ffffffffc0c4a988 RDI: 0000000000000004
[ 129.374474] RBP: ffff9f9141e7fd10 R08: 0000000000000005 R09: 0000000000000000
[ 129.374475] R10: 0000000000000002 R11: 0000000000000001 R12: ffff91eebd510c00
[ 129.374475] R13: ffff91eebd510e58 R14: ffff91ef052c01b8 R15: 0000000000000006
[ 129.374476] FS: 0000000000000000(0000) GS:ffff91ef0ef80000(0000) knlGS:0000000000000000
[ 129.374477] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 129.374478] CR2: 000055623ea01d50 CR3: 0000000408a8c000 CR4: 00000000003406e0
[ 129.374479] Call Trace:
[ 129.374550] dc_link_reallocate_mst_payload+0x12e/0x150 [amdgpu]
[ 129.374617] dc_link_handle_hpd_rx_irq+0x6d4/0x6e0 [amdgpu]
[ 129.374693] handle_hpd_rx_irq+0x77/0x310 [amdgpu]
[ 129.374768] dm_irq_work_func+0x53/0x70 [amdgpu]
[ 129.374774] process_one_work+0x1fd/0x3f0
[ 129.374776] worker_thread+0x255/0x410
[ 129.374778] kthread+0x121/0x140
[ 129.374780] ? process_one_work+0x3f0/0x3f0
[ 129.374781] ? kthread_park+0x90/0x90
[ 129.374785] ret_from_fork+0x22/0x40
[How]
when we disable MST we should clear the cur link settings (lane_count=0 is
good enough). This will cause us to not reallocate payloads earlier than
expected and not throw the warning
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Use the existence of the workqueue itself to determine when to
enable HDCP features rather than sprinkling asic checks all over
the code. Also add a check for the existence of the hdcp
workqueue in the irq handling on the off chance we get and HPD
RX interrupt with the CP bit set. This avoids a crash if
the driver doesn't support HDCP for a particular asic.
Fixes: 96a3b32e67236f ("drm/amd/display: only enable HDCP for DCN+")
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=206519
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We were using incorrect byte order after we started using the drm_defines
So fix it.
Fixes: 02837a91ae75 ("drm/amd/display: add and use defines from drm_hdcp.h")
Signed-off-by: JinZe.Xu <JinZe.Xu@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Programming DPPCLK to the same value currently set may cause
underflow while playing video in certain conditions.
[HOW]
Only program DPPCLK if clock is not the same as the
previous value programmed.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
In DCN hardware sequencer we do actually call ATOM_INIT correctly per
pipe. The workaround is not necessary for command table offloading.
[How]
Drop the workaround since it's not needed.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
On PowerPC, the compiler will tag object files with whether they
use hard or soft float FP ABI and whether they use 64 or 128-bit
long double ABI. On systems with 64-bit long double ABI, a tag
will get emitted whenever a double is used, as on those systems
a long double is the same as a double. This will prevent linkage
as other files are being compiled with hard-float.
On ppc64, this code will never actually get used for the time
being, as the only currently existing hardware using it are the
Renoir APUs. Therefore, until this is testable and can be fixed
properly, at least make sure the build will not fail.
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Starting from 14nm, the PLL is built into the PHY and the PLL is mapped
to PHY on 1 to 1 basis. In the code, the DP port is mapped to a PLL that was not
initialized. This causes DP to HDMI dongle to not light up the display.
[How]
Initializations added for PLL2 when creating resources.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Underflow is observed when plug in a 4K@60 monitor with
1366x768 eDP due to DPPCLK is too low.
[How]
Limit minimum DPPCLK to 100MHz.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Engine can be NULL in some cases, so we must not acquire it.
[How]
Check for NULL engine before acquiring.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY & HOW]
Previously drain clk was unconstrained and fill clk was constrained on fclk.
We want to change it to fill clk unconstrained and drain clock constrained
to dcfclk.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
The optimized_require flag is needed to set watermarks and clocks lower
in certain conditions. This flag is set to true and then set to false
while programming front end in dcn20.
[HOW]
Do not set the flag to false while disabling plane.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Driver crash with psr feature enabled due to divide-by-zero error.
This is a regression after rework to calculate static screen frame
number entry time.
[How]
Correct order of operations to avoid divide-by-zero.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Disabling a display on MST can potentially happen after the entire MST
topology has been removed, which means that we can't communicate with
the topology at all in this scenario. Likewise, this also means that we
can't properly update payloads on the topology and as such, it's a good
idea to ignore payload update failures when disabling displays.
Currently, amdgpu makes the mistake of halting the payload update
process when any payload update failures occur, resulting in leaving
DC's local copies of the payload tables out of date.
This ends up causing problems with hotplugging MST topologies, and
causes modesets on the second hotplug to fail like so:
[drm] Failed to updateMST allocation table forpipe idx:1
------------[ cut here ]------------
WARNING: CPU: 5 PID: 1511 at
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link.c:2677
update_mst_stream_alloc_table+0x11e/0x130 [amdgpu]
Modules linked in: cdc_ether usbnet fuse xt_conntrack nf_conntrack
nf_defrag_ipv6 libcrc32c nf_defrag_ipv4 ipt_REJECT nf_reject_ipv4
nft_counter nft_compat nf_tables nfnetlink tun bridge stp llc sunrpc
vfat fat wmi_bmof uvcvideo snd_hda_codec_realtek snd_hda_codec_generic
snd_hda_codec_hdmi videobuf2_vmalloc snd_hda_intel videobuf2_memops
videobuf2_v4l2 snd_intel_dspcfg videobuf2_common crct10dif_pclmul
snd_hda_codec videodev crc32_pclmul snd_hwdep snd_hda_core
ghash_clmulni_intel snd_seq mc joydev pcspkr snd_seq_device snd_pcm
sp5100_tco k10temp i2c_piix4 snd_timer thinkpad_acpi ledtrig_audio snd
wmi soundcore video i2c_scmi acpi_cpufreq ip_tables amdgpu(O)
rtsx_pci_sdmmc amd_iommu_v2 gpu_sched mmc_core i2c_algo_bit ttm
drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops cec drm
crc32c_intel serio_raw hid_multitouch r8152 mii nvme r8169 nvme_core
rtsx_pci pinctrl_amd
CPU: 5 PID: 1511 Comm: gnome-shell Tainted: G O 5.5.0-rc7Lyude-Test+ #4
Hardware name: LENOVO FA495SIT26/FA495SIT26, BIOS R12ET22W(0.22 ) 01/31/2019
RIP: 0010:update_mst_stream_alloc_table+0x11e/0x130 [amdgpu]
Code: 28 00 00 00 75 2b 48 8d 65 e0 5b 41 5c 41 5d 41 5e 5d c3 0f b6 06
49 89 1c 24 41 88 44 24 08 0f b6 46 01 41 88 44 24 09 eb 93 <0f> 0b e9
2f ff ff ff e8 a6 82 a3 c2 66 0f 1f 44 00 00 0f 1f 44 00
RSP: 0018:ffffac428127f5b0 EFLAGS: 00010202
RAX: 0000000000000002 RBX: ffff8d1e166eee80 RCX: 0000000000000000
RDX: ffffac428127f668 RSI: ffff8d1e166eee80 RDI: ffffac428127f610
RBP: ffffac428127f640 R08: ffffffffc03d94a8 R09: 0000000000000000
R10: ffff8d1e24b02000 R11: ffffac428127f5b0 R12: ffff8d1e1b83d000
R13: ffff8d1e1bea0b08 R14: 0000000000000002 R15: 0000000000000002
FS: 00007fab23ffcd80(0000) GS:ffff8d1e28b40000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f151f1711e8 CR3: 00000005997c0000 CR4: 00000000003406e0
Call Trace:
? mutex_lock+0xe/0x30
dc_link_allocate_mst_payload+0x9a/0x210 [amdgpu]
? dm_read_reg_func+0x39/0xb0 [amdgpu]
? core_link_enable_stream+0x656/0x730 [amdgpu]
core_link_enable_stream+0x656/0x730 [amdgpu]
dce110_apply_ctx_to_hw+0x58e/0x5d0 [amdgpu]
? dcn10_verify_allow_pstate_change_high+0x1d/0x280 [amdgpu]
? dcn10_wait_for_mpcc_disconnect+0x3c/0x130 [amdgpu]
dc_commit_state+0x292/0x770 [amdgpu]
? add_timer+0x101/0x1f0
? ttm_bo_put+0x1a1/0x2f0 [ttm]
amdgpu_dm_atomic_commit_tail+0xb59/0x1ff0 [amdgpu]
? amdgpu_move_blit.constprop.0+0xb8/0x1f0 [amdgpu]
? amdgpu_bo_move+0x16d/0x2b0 [amdgpu]
? ttm_bo_handle_move_mem+0x118/0x570 [ttm]
? ttm_bo_validate+0x134/0x150 [ttm]
? dm_plane_helper_prepare_fb+0x1b9/0x2a0 [amdgpu]
? _cond_resched+0x15/0x30
? wait_for_completion_timeout+0x38/0x160
? _cond_resched+0x15/0x30
? wait_for_completion_interruptible+0x33/0x190
commit_tail+0x94/0x130 [drm_kms_helper]
drm_atomic_helper_commit+0x113/0x140 [drm_kms_helper]
drm_atomic_helper_set_config+0x70/0xb0 [drm_kms_helper]
drm_mode_setcrtc+0x194/0x6a0 [drm]
? _cond_resched+0x15/0x30
? mutex_lock+0xe/0x30
? drm_mode_getcrtc+0x180/0x180 [drm]
drm_ioctl_kernel+0xaa/0xf0 [drm]
drm_ioctl+0x208/0x390 [drm]
? drm_mode_getcrtc+0x180/0x180 [drm]
amdgpu_drm_ioctl+0x49/0x80 [amdgpu]
do_vfs_ioctl+0x458/0x6d0
ksys_ioctl+0x5e/0x90
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x55/0x1b0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7fab2121f87b
Code: 0f 1e fa 48 8b 05 0d 96 2c 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff
ff ff c3 66 0f 1f 44 00 00 f3 0f 1e fa b8 10 00 00 00 0f 05 <48> 3d 01
f0 ff ff 73 01 c3 48 8b 0d dd 95 2c 00 f7 d8 64 89 01 48
RSP: 002b:00007ffd045f9068 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007ffd045f90a0 RCX: 00007fab2121f87b
RDX: 00007ffd045f90a0 RSI: 00000000c06864a2 RDI: 000000000000000b
RBP: 00007ffd045f90a0 R08: 0000000000000000 R09: 000055dbd2985d10
R10: 000055dbd2196280 R11: 0000000000000246 R12: 00000000c06864a2
R13: 000000000000000b R14: 0000000000000000 R15: 000055dbd2196280
---[ end trace 6ea888c24d2059cd ]---
Note as well, I have only been able to reproduce this on setups with 2
MST displays.
Changes since v1:
* Don't return false when part 1 or part 2 of updating the payloads
fails, we don't want to abort at any step of the process even if
things fail
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We might get different numbers of clocks from powerplay depending
on what the OEM has populated.
v2: add assert for at least one level
Bug: https://gitlab.freedesktop.org/drm/amd/issues/963
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
When we disable a connector we don't explicitly remove it from the module so the
display is still cached(SW) in the hdcp_module.
SST: no issues because we can only have 1 display per link
MST: We have x displays per link, now if we disable 1 we don't remove it from the
module so the module has x display cached(SW).
If we try to enable HDCP, psp verification will fail because we are reporting x
displays while the HW only has x-1 display enabled
[How]
Check the callback for when we disable stream and call remove display.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
Remove a backslash symbol accidentally left in increase bpp function
when computing mst dsc configuration.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
In current code we're essentially drawing the cursor on every pipe
that contains it. This only works when the planes have the same
scaling for src to dest rect, otherwise we'll get "double cursor" where
one cursor is incorrectly filtered and offset from the real position.
[How]
Without dedicated cursor planes on DCN we require at least one pipe
that matches the scaling of the current timing.
This is an optimization and workaround for the most common case where
the top-most plane is not scaled but the bottom-most plane is scaled.
Whenever a pipe has a parent pipe in the blending tree whose recout
fully contains the current pipe we can disable the pipe.
This only applies when the pipe is actually visible of course.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Need to do atomic check first, then validate global state.
If not, when connecting both MST and HDMI displays and
set a bad mode via xrandr, system will hang.
[How]
Move drm_dp_mst_atomic_check() to the front of
dc_validate_global_state().
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
There is a spelling mistake on the struct field name link_integiry_check,
fix this by renaming it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
A for-loop is iterating from 0 up to 1000 however the loop variable count
is a u8 and hence not large enough. Fix this by making count an int.
Also remove the redundant initialization of count since this is never used
and add { } on the loop statement make the loop block clearer.
v2: drop useless else (Walter Harms)
Addresses-Coverity: ("Operands don't affect result")
Fixes: ed581a0ace44 ("drm/amd/display: wait for update when setting dpg test pattern")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This allocation isn't required and can fail when resuming from suspend.
Bug: https://gitlab.freedesktop.org/drm/amd/issues/1009
Signed-off-by: Dor Askayo <dor.askayo@gmail.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This reverts commit 80adaebd2d411b7d6872a097634848a71eb13d20.
[WHY]
This change was working around a regression that occured in this:
commit 0301ccbaf67d ("drm/amd/display: DP Compliance 400.1.1 failure")
With the fix to run verify_link_cap when the SINK_COUNT of
dongles becomes non-zero this change is no longer needed.
Cc: Louis Li <Ching-shih.Li@amd.com>
Cc: Wenjing Liu <Wenjing.Liu@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Two years ago the patch referenced by the Fixes tag stopped running
dp_verify_link_cap_with_retries during DP detection when the reason
for the detection was a short-pulse interrupt. This effectively meant
that we were no longer doing the verify_link_cap training on active
dongles when their SINK_COUNT changed from 0 to 1.
A year ago this was partly remedied with:
commit 80adaebd2d41 ("drm/amd/display: Don't skip link training for empty dongle")
This made sure that we trained the dongle on initial hotplug (without
connected downstream devices).
This is all fine and dandy if it weren't for the fact that there are
some dongles on the market that don't like link training when SINK_COUNT
is 0 These dongles will in fact indicate a SINK_COUNT of 0 immediately
after hotplug, even when a downstream device is connected, and then
trigger a shortpulse interrupt indicating a SINK_COUNT change to 1.
In order to play nicely we will need our policy to not link train an
active DP dongle when SINK_COUNT is 0 but ensure we train it when the
SINK_COUNT changes to 1.
[HOW]
Call dp_verify_link_cap_with_retries on detection even when the detection
is triggered from a short pulse interrupt.
With this change we can also revert this commit which we'll do in a separate
follow-up change:
commit 80adaebd2d41 ("drm/amd/display: Don't skip link training for empty dongle")
Fixes: 0301ccbaf67d ("drm/amd/display: DP Compliance 400.1.1 failure")
Suggested-by: Louis Li <Ching-shih.Li@amd.com>
Tested-by: Louis Li <Ching-shih.Li@amd.com>
Cc: Wenjing Liu <Wenjing.Liu@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
FMT has limitation to support YCbCr420 with h_active greater than 4096.
[how]
Use odm combine to overcome the limitation.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Driver didn't init hw i2c speed cause hdcp hw cannot
send command, because the default value of speed register
is 0x2.
[How]
Restore the default speed when release i2c engine
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
MPO isn't enabled on some 4k videos due to video source width is 4096
and the current limit is 3840.
[How]
Changed the limit to 4096.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
MSA will be deprecated in the future.
Need to support VSC during DP test automation.
[how]
Do not disable VSC during DP test automation.
TODO - need to add VSC update on DM side on test request.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
CW2 may already be programmed when coming back from S4. In this case
we want to unconditionally replace whatever DMCUB version is currently
enabled with the latest.
[How]
Check the hw_init flag to know whether or not we've previously executed
the initliazed routine.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
These logically make sense more to be set after the DMCUB has been
reset rather than when we setup the inbox.
[How]
Move them into the reset callback.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
DMCUB command table doesn't support ATOM_ENABLE/ATOM_DISABLE anymore
so we never end up calling the DCN init path in DMCUB.
[How]
Map ATOM_ENABLE to ATOM_INIT only for DMCUB command table offloading.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
We'll need this to perform a clean shutdown before unloading the driver.
[How]
It will call reset internally and set hw_init to false. It won't do
anything if the hardware isn't initialized.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
determine_update_type_for_commit() uses pointers to single instance
of local variable to fill scaling/color info for all planes updates.
This is a bug, that leads to incorrect update type for commit in case
of multiple planes per crtc.
Each plane should refer to separate scaling/color data.
[How]
Use arrays for plane properties.
Bundle all properties into a single structure to simplify memory allocation.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Hardcoded fixed values are not proper.
[How]
Use enum values instead of fixed numbers.
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
In HG mode, vbios didn't call DispController_Init to program NV1x
XTAL_REF_DIV value when ASIC_INIT, but driver read XTAL_REF_DIV
to calculate i2c reference frequency. it cause i2c frequency change
from 100kHz to 200kHz.
[How]
remove get_speed function and calculate reference frequency at
set_speed functiton.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
It has duplicate code for building regamma curve
[How]
Remove the duplicate code and use the same function for building regamma
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
The types for dummyinteger1 and dummyinteger2 are unsigned
as part of the DML spec. They should not be long.
[How]
Make them unsigned int instead of long.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
For DMCUB enabled hardware DC has a dependency on DMCUB already being
running.
Command table offloading will fail on first modeset if DMCUB isn't
initialized first.
[How]
Perform DMCUB hardware initialization before DC.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Switched to C-style comments for consistency
Signed-off-by: Haiyi Zhou <haiyi.zhou@amd.com>
Reviewed-by: Reza Amini <Reza.Amini@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Driver use pipe_ctx to reallocate payload may cause allocate
payload twice on same sink with split pipe.
[How]
Drvier must to check pipe_ctx is split pipe or not to avoid
reallocate payload twice on same sink.
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
If the command table isn't available then we can fallback to DMCUB
offloading if it's enabled and available.
[How]
Instead of assigning NULL for supported command table functions we can
fallback to the DMCUB when it's available.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Under some hardware initialization sequences the fb base/fb offset
provided can be zero or hardwareinit can happen too late.
We want to ensure that we always have the correct fb_base/fb_offset
when performing DMCUB hardware initialization so we can do DMCUB
command table offloading during first dc hardware init.
[How]
Read from the DCN registers. VBIOS already filled these in for us.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[how]
Empty dsc enc caps when debug option is set to disable DSC.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
The DP 1.4a Spec requires that training pattern only under certain
specific conditions. Currently driver will re-send
training pattern every time voltage swing value changes,
but that should not be the case.
[How]
Do not re-send training pattern every time VS values
are different. Only send it on the first iteration.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
On video test pattern request we need to update MSA and VSC so
it will match the requested test pattern dynamic range field.
[how]
Update dynamic range field in MSA and disable VSC as updating VSC
info packet is complicated and not required for test pattern purpose.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
DPG is used to generate both blank and test automation test pattern.
When test automation is running the requested test pattern can be
overriden by the blank or unblank call because it is using the same
hardware.
[how]
When test pattern is requested, skip blank or unblank.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Try to allocate MST payload but receive HPD short pulse with link loss
casue driver allocate payload twice. It cause monitor can't light up
successfully.
[How]
When driver receive HPD short pulse with link loss, we need to
deallocate payload then allocate payload.
Then we will not allocate payload twice with same sink.
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|