aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/gpu/drm/amd/display
AgeCommit message (Collapse)AuthorFilesLines
2021-02-02drm/amd/display: Reject too small viewport size when validating planeNikola Cornij3-3/+29
[why] Overlay won't move to a new positon if viewport size is smaller than what can be handled. It'd either disappear or stay at the old position. This condition is for example hit if overlay is moved too much outside of left or top edge of the screen, but it applies to any non-cursor plane type. [how] Reject this contidion at validation time. This gives the calling level a chance to handle this gracefully and avoid inconsistent behaivor. Signed-off-by: Nikola Cornij <nikola.cornij@amd.com> Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-02drm/amd/display: Better handling of dummy p-state tableJoshua Aberback1-7/+5
[Why] Some scenarios where we use a UCLK frequency in between dummy p-state table entries result in a p-state hang, due to the table not having a close enough match, so the default DPM0 latency is used, which can be too long to support dummy p-state switching in these scenarios. [How] - old: match if current freq is within +- margin of table entry - new: find largest table entry that is lower than current freq + margin - lower than DPM0 will still use DPM0 Signed-off-by: Joshua Aberback <joshua.aberback@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-02drm/amd/display: Workaround for some legacy DP-VGA donglesTaimur Hassan1-1/+12
[Why] Maximum resolution is 1440*900 when connecting to FHD monitor via some DP-VGA dongles. The display EDID reading fails over AUX/I2C via DP->VGA dongle, and this leads to the maximum resolution 1920*1080 cannot be obtained from EDID. [How] Provide a workaround for some legacy DP-VGA dongles with a longer aux delay. Signed-off-by: Taimur Hassan <syed.hassan@amd.com> Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-02drm/amd/display: Decrement refcount of dc_sink before reassignmentVictor Lu1-1/+3
[why] An old dc_sink state is causing a memory leak because it is missing a dc_sink_release before a new dc_sink is assigned back to aconnector->dc_sink. [how] Decrement the dc_sink refcount before reassigning it to a new dc_sink. Signed-off-by: Victor Lu <victorchengchi.lu@amd.com> Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-02drm/amd/display: Free atomic state after drm_atomic_commitVictor Lu1-8/+6
[why] drm_atomic_commit was changed so that the caller must free their drm_atomic_state reference on successes. [how] Add drm_atomic_commit_put after drm_atomic_commit call in dm_force_atomic_commit. Signed-off-by: Victor Lu <victorchengchi.lu@amd.com> Reviewed-by: Roman Li <Roman.Li@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-02drm/amd/display: remove unused force_ignore_link_settings debug optionWenjing Liu2-4/+0
[why] Remove force_ignore_link_settings debug option as it is no longer used. Signed-off-by: Wenjing Liu <wenjing.liu@amd.com> Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-02drm/amd/display: Add Freesync HDMI support to DMCUStylon Wang6-1/+268
[Why] Adding support for Freesync HDMI to DC and DMCU [How] Create DC interface and implementation on top of DMCU to support parsing CEA blocks in DMCU. Signed-off-by: Stylon Wang <stylon.wang@amd.com> Reviewed-by: Hersen Wu <hersenxs.wu@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-02drm/amd/display: Enable "trigger_hotplug" debugfs on all outputsStylon Wang1-4/+6
[Why] Per-connector debugfs entry "trigger_hotplug" is available on DP/eDP only. New IGT tests need this entry to test other outputs. [How] Enable this debugfs entry on all types of connectors Signed-off-by: Stylon Wang <stylon.wang@amd.com> Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-02drm/amd/display: Fix CW4 programming for dmub30 cached inboxNicholas Kazlauskas3-2/+4
[Why] The conditions for whether we used cached vs non-cached inbox1 depend on a version check that mismatches what the shared helpers in dmub20 implement. [How] Use the dmub_dcn20_use_cached_inbox check for dmub_dcn30 as well. Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-02drm/amd/display: fix initial bounding box values for dcn3.02Samson Tam3-10/+184
[Why] Initial bounding box values are updated in dcn30_update_bw_bounding_box but they use dcn3_0_soc and dcn3_0_ip instead of dcn3_02_soc and dcn3_02_ip [How] Add dcn302_update_bw_bounding_box and dcn302_get_optimal_dcfclk_fclk_for_uclk so it uses dcn3_02_soc and dcn3_02_ip. Use sr_exit_time_us, sr_enter_plus_exit_time_us, from dcn30 on dcn302 to fix flicker on eDP. Also use dram_clock_change_latency_us from dcn30. Signed-off-by: Samson Tam <Samson.Tam@amd.com> Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-02drm/amd/display: implement support for DID2.0 dsc passthroughJun Lei3-14/+23
[Why] Some panels contain active converters (e.g. DP to MIPI) which only support restricted DSC configurations. DID2.0 adds support for such displays to explicitly define per timing BPP restrictions on DSC. Ignoring these restrictions leads to blackscreen. [How] Add parsing in DID2.0 parser to get this bpp info. Add support in DSC module to constraint target bpp based on this info. Signed-off-by: Jun Lei <jun.lei@amd.com> Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-02drm/amd/display: Fix dc_sink kref count in emulated_link_detectVictor Lu1-2/+2
[why] prev_sink is not used anywhere else in the function and the reference to it from dc_link is replaced with a new dc_sink. [how] Change dc_sink_retain(prev_sink) to dc_sink_release(prev_sink). Signed-off-by: Victor Lu <victorchengchi.lu@amd.com> Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-02drm/amd/display: Release DSC before acquiringMikita Lipski1-1/+5
[why] Need to unassign DSC from pipes that are not using it so other pipes can acquire it. That is needed for asic's that have unmatching number of DSC engines from the number of pipes. [how] Before acquiring dsc to stream resources, first remove it. Signed-off-by: Mikita Lipski <mikita.lipski@amd.com> Reviewed-by: Eryk Brol <Eryk.Brol@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-02drm/amd/display: Revert "Fix EDID parsing after resume from suspend"Stylon Wang1-2/+0
This reverts commit b24bdc37d03a0478189e20a50286092840f414fa. It caused memory leak after S3 on 4K HDMI displays. Signed-off-by: Stylon Wang <stylon.wang@amd.com> Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-02drm/amd/display: fix calculation for the pwl backlight curveAnthony Koo1-1/+1
[Why] The PWL backlight curve is used by the firmware to convert between brightness and linear PWM value. Driver has a backlight LUT, but the firmware holds a PWL curve and interpolates between points. The calculations are incorrect leading to slightly off backlight values being programmed. [How] Fix the PWL backlight curve threshold/offset calculations Signed-off-by: Anthony Koo <Anthony.Koo@amd.com> Reviewed-by: Josip Pavic <Josip.Pavic@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-02drm/amd/display: 3.2.120Aric Cyr1-1/+1
This DC update brings improvements in multiple areas. In summary, we highlight: - Fix display detection on HDMI ComboPHY - Drop SOC bounding box hookup - Fix DPCD values Signed-off-by: Aric Cyr <aric.cyr@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-02drm/amd/display: [FW Promotion] Release 0.0.49Anthony Koo1-2/+3
- Add field for passing line time for a frame Signed-off-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-02drm/amd/display: Add more Clock Sources to DCN2.1Sung Lee1-0/+10
[WHY] When enabling HDMI on ComboPHY, there are not enough clock sources to complete display detection. [HOW] Initialize more clock sources. Signed-off-by: Sung Lee <sung.lee@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-02drm/amd/display: correct some hdcp variable namingWenjing Liu6-17/+19
[why] In HDCP update stream config interface, some variables are named as xxx_supported, but in fact the variable indicates whether or not xxx_enabled. Correct the naming so it is less confusing to read the code. Signed-off-by: Wenjing Liu <wenjing.liu@amd.com> Reviewed-by: George Shen <George.Shen@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-02drm/amd/display: Set power_gated to true for seamless boot pipe initLewis Huang1-0/+1
[Why] In seamless boot without a flip case, the flag power_gated didn't get cleared when resetting path mode because the plane_state is null. The following sequence will cause this issue: 1. OS call set mode to clone/extended 2. Reset path mode to remove edp [How] Set power gated default to true in seamless boot pipe Signed-off-by: Lewis Huang <Lewis.Huang@amd.com> Reviewed-by: Martin Leung <Martin.Leung@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-02drm/amd/display: reuse current context instead of recreating oneBhawanpreet Lakha3-23/+30
[Why] Currently we discard the current context and recreate it. The current context is what is applied to the HW so we should be re-using this rather than creating a new context. Recreating the context can lead to mismatch between new context and the current context For example: gsl groups get changed when we create a new context this can cause issues in a multi display config (with flip immediate) because we don't align the existing gsl groups in the new and current context. If we reuse the current context the gsl group assignment stays the same. [How] Instead of discarding the current context, we instead just copy the current state and add/remove planes and streams. Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-02drm/amd/display: Add null pointer check to is_dig_enabled funcMichael Strauss1-1/+2
[WHY] Safeguarding as pointer may be null in diagnostic environment Signed-off-by: Michael Strauss <michael.strauss@amd.com> Reviewed-by: Sung Lee <Sung.Lee@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-02drm/amd/display: initialize i2c speed if not initialized in dcnxxx__resource.cBrendan Steve Leder1-0/+4
Some dcnxxx__resource.c do not initialize the i2c speed; this patch adds the required initialization at dc_construct(). Signed-off-by: Brendan Steve Leder <brendanSteve.Leder@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-02drm/amd/display: Fix DPCD translation for LTTPR AUX_RD_INTERVALGeorge Shen1-3/+3
[Why] The translation between the DPCD value and the specified AUX_RD_INTERVAL in the DP spec do not match. [How] Update values to match the spec. Signed-off-by: George Shen <george.shen@amd.com> Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-02drm/amd/display: Drop SOC bounding box hookup in DM/DCNicholas Kazlauskas6-330/+4
[Why] There aren't any ASIC where we use these binaries and they aren't useful for future use since it's inconvenient to extend and maintain these structures. [How] Drop the support from DM and DC for now. Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Roman Li <Roman.Li@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Acked-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Hersen Wu <hersenxs.wu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-02-01drm/amd/display: Simplify bool conversionAbaci Team1-1/+1
Fix the following coccicheck warning: ./drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hw_sequencer.c:3137:35-40: WARNING: conversion to bool not needed here Reported-by: Abaci Robot <abaci@linux.alibaba.com> Suggested-by: Yang Li <oswb@linux.alibaba.com> Signed-off-by: Abaci Team <abaci-bugfix@linux.alibaba.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-01-25drm/amd/display: Fix HDMI deep color output for DCE 6-11.Mario Kleiner3-0/+76
This fixes corrupted display output in HDMI deep color 10/12 bpc mode at least as observed on AMD Mullins, DCE-8.3. It will hopefully also provide fixes for other DCE's up to DCE-11, assuming those will need similar fixes, but i could not test that for HDMI due to lack of suitable hw, so viewer discretion is advised. dce110_stream_encoder_hdmi_set_stream_attribute() is used for HDMI setup on all DCE's and is missing color_depth assignment. dce110_program_pix_clk() is used for pixel clock setup on HDMI for DCE 6-11, and is missing color_depth assignment. Additionally some of the underlying Atombios specific encoder and pixelclock setup functions are missing code which is in the classic amdgpu kms modesetting path and the in the radeon kms driver for DCE6/DCE8. encoder_control_digx_v3() - Was missing setup code wrt. amdgpu and radeon kms classic drivers. Added here, but untested due to lack of suitable test hw. encoder_control_digx_v4() - Added missing setup code. Successfully tested on AMD mullins / DCE-8.3 with HDMI deep color output at 10 bpc and 12 bpc. Note that encoder_control_digx_v5() has proper setup code in place and is used, e.g., by DCE-11.2, but this code wasn't used for deep color setup due to the missing cntl.color_depth setup in the calling function for HDMI. set_pixel_clock_v5() - Missing setup code wrt. classic amdgpu/radeon kms. Added here, but untested due to lack of hw. set_pixel_clock_v6() - Missing setup code added. Successfully tested on AMD mullins DCE-8.3. This fixes corrupted display output at HDMI deep color output with 10 bpc or 12 bpc. Fixes: 4562236b3bc0 ("drm/amd/dc: Add dc display driver (v2)") Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Cc: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-01-25drm/amd/display: Fix 10/12 bpc setup in DCE output bit depth reduction.Mario Kleiner1-4/+4
In set_clamp(), the comments and definitions for the COLOR_DEPTH_101010 and COLOR_DEPTH_121212 cases directly contradict the code comment which explains how this should work, whereas the COLOR_DEPTH_888 case is consistent with the code comments. Comment says the bitmask should be chosen to align to the top-most 10 or 12 MSB's on a 14 bit bus, but the implementation contradicts that: 10 bit case sets a mask for 12 bpc clamping, whereas 12 bit case sets a mask for 14 bpc clamping. Note that during my limited testing on DCE-8.3 (HDMI deep color) and DCE-11.2 (DP deep color), this didn't have any obvious ill effects, neither did fixing it change anything obvious for the better, so this fix may be inconsequential on DCE, and just reduce the confusion of innocent bystanders when reading the code and trying to investigate problems with 10 bpc+ output. Fixes: 4562236b3bc0 ("drm/amd/dc: Add dc display driver (v2)") Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Cc: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-01-25amdgpu: fix clang build warningArnd Bergmann3-4/+8
clang warns about the -mhard-float command line arguments on architectures that do not support this: clang: error: argument unused during compilation: '-mhard-float' [-Werror,-Wunused-command-line-argument] Move this into the gcc-specific arguments. Fixes: e77165bf7b02 ("drm/amd/display: Add DCN3 blocks to Makefile") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-01-25drm/amd/display: Fix a potential NULL dereferenceDan Carpenter1-2/+2
The debug printk dereferences "link->link_enc" before we have ensured that it is non-NULL. Fix this potential NULL derefence by moving the printk after the check. Fixes: 64ff0882426e56 ("drm/amd/display: Log link/connector info provided in BIOS object table") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-01-25drm/amd/display: change license of color_table.cJonathan Gray1-5/+21
Change the license of color_table.c to match color_table.h granting permission to modify and distribute. Signed-off-by: Jonathan Gray <jsg@jsg.id.au> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-01-25drm/amd/display: fix 64-bit division issue on 32-bit OSLang Yu1-6/+6
Replace "/" with div_u64 for 32-bit OS. On 32-bit OS, the use of "/" for 64-bit division will cause build error, i.e. "__udivdi3/__divdi3 undefined!". Fixes: ea7154d8d9fb26 ("drm/amd/display: Update dcn30_apply_idle_power_optimizations() code") Signed-off-by: Lang Yu <Lang.Yu@amd.com> Acked-by: Huang Rui <ray.huang@amd.com> Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-01-25Revert "drm/amd/display: Tune min clk values for MPO for RV"Pratik Vishwakarma1-27/+3
This reverts commit 57eeaf47a613c67d0380cf0afad73d8f52df2670. Original issue of flash line when MPO enabled on idle screen was fixed by raising clocks. This had negative effect of extra power being drained. With the upstream commit 9d03bb102028 ("drm/amd/display: disable dcn10 pipe split by default") flash line issue was fixed and had positive effect for battery life. Hence this patch is no more required. Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com> Reviewed-by: Hersen Wu <hersenxs.wu@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-01-21drm/amdgpu: Assign boolean values to a bool variableJiapeng Zhong1-16/+16
Fix the following coccicheck warnings: ./drivers/gpu/drm/amd/display/dc/dml/dcn30/display_rq_dlg_calc_30.c: 1009:6-16: WARNING: Assignment of 0/1 to bool variable. ./drivers/gpu/drm/amd/display/dc/dml/dcn30/display_rq_dlg_calc_30.c: 200:2-10: WARNING: Assignment of 0/1 to bool variable. Reviewed-by: Harry Wentland <harry.wentland@amd.com> Reported-by: Abaci Robot <abaci@linux.alibaba.com> Signed-off-by: Jiapeng Zhong <abaci-bugfix@linux.alibaba.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-01-21drm/amd/display: Fix spelling mistake of function nameColin Ian King1-2/+2
There are two spelling mistakes of the function name, fix this by using __func__ instead of a hard coded name string. Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-01-21drm/amd/display: Update dcn30_apply_idle_power_optimizations() codeBhawanpreet Lakha4-39/+129
Update the function for idle optimizations -remove hardcoded size -enable no memory-request case -add cursor copy -update mall eligibility check case Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Joshua Aberback <joshua.aberback@amd.com> Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-01-21drm/amd/display: Dynamic cursor cache size for MALL eligibility checkBhawanpreet Lakha6-9/+33
[Why] Currently we use the maximum possible cursor cache size when deciding if we should attempt to enable MALL, but this prevents us from enabling the feature for certain key use cases. [How] - consider cursor bpp when calculating if the cursor fits Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Joshua Aberback <joshua.aberback@amd.com> Reviewed-by: Aric Cyr <aric.cyr@amd.com> Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-01-21drm/amd/display: Enable programing of MALL watermarksBhawanpreet Lakha1-9/+9
-Uncomment watermark set d -This populates the wm table so that it can be sent to PMFW -This watermark table is used when we are in mall stutter Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-01-20drm/amd/display: 3.2.119Aric Cyr1-1/+1
Signed-off-by: Aric Cyr <aric.cyr@amd.com> Acked-by: Anson Jacob <anson.jacob@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-01-20drm/amd/display: [FW Promotion] Release 0.0.48Anthony Koo1-2/+2
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Anson Jacob <anson.jacob@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-01-20drm/amd/display: Update dram_clock_change_latency for DCN2.1Jake Wang1-1/+1
[WHY] dram clock change latencies get updated using ddr4 latency table, but that update does not happen before validation. This value should not be the default and should be number received from df for better mode support. This may cause a PState hang on high refresh panels with short vblanks such as on 1080p 360hz or 300hz panels. [HOW] Update latency from 23.84 to 11.72. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Jake Wang <haonan.wang2@amd.com> Reviewed-by: Sung Lee <Sung.Lee@amd.com> Acked-by: Anson Jacob <anson.jacob@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-01-20drm/amd/display: Allow PSTATE chnage when no displays are enabledAric Cyr1-2/+4
[Why] When no displays are currently enabled, display driver should not disallow PSTATE switching. [How] Allow PSTATE switching if either the active configuration supports it, or there are no active displays. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Aric Cyr <aric.cyr@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Anson Jacob <anson.jacob@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-01-20drm/amd/display: Fix dml20v2_ModeSupportAndSystemConfigurationFull() to check DesiredBPP.Bing Guo1-38/+79
Why: dml20v2_ModeSupportAndSystemConfigurationFull() didn't check against DesiredBPP, so it doesn't work correctly when DesiredBPP can't be satisfied. How: Port the TruncToValidBPP() version from display_mode_vba_21.c to display_mode_vba_20v2.c. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Bing Guo <bing.guo@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Anson Jacob <anson.jacob@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-01-20drm/amd/display: Log link/connector info provided in BIOS object tableGeorge Shen3-0/+30
[Why/How] Add logging statements to assist in debugging errors in the BIOS object table. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: George Shen <george.shen@amd.com> Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by: Anson Jacob <anson.jacob@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-01-20drm/amd/display: Allow dmu_stg to support cached inbox for dmubWyatt Wood1-2/+9
[Why] FW version check doesn't allow dmu_stg to support cached inbox, which yields much better performance than region 4. [How] Check a range of fw versions, rather than a simple greater than check. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Wyatt Wood <wyatt.wood@amd.com> Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by: Anson Jacob <anson.jacob@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-01-20drm/amd/display: Change function decide_dp_link_settings to avoid infinite loopingBing Guo1-0/+3
Why: Function decide_dp_link_settings() loops infinitely when required bandwidth can't be supported. How: Check the required bandwidth against verified_link_cap before trying to find a link setting for it. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Bing Guo <bing.guo@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Anson Jacob <anson.jacob@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-01-20drm/amd/display: Fix reset sequence with driver direct DMCUB fw loadNicholas Kazlauskas1-3/+3
[Why] DMCUB encounters a page fault/double exception with driver direct load because DMCUB is not held in soft reset after releasing secure reset. The clean shutdown sequence via GPINT is also not executed in this sequence which leaves hardware behavior in an indeterminate state. [How] Move reset earlier in the sequence. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Eric Yang <eric.yang2@amd.com> Acked-by: Anson Jacob <anson.jacob@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-01-20drm/amd/display: Guard against NULL pointer deref when get_i2c_info failsNicholas Kazlauskas1-0/+5
[Why] If the BIOS table is invalid or corrupt then get_i2c_info can fail and we dereference a NULL pointer. [How] Check that ddc_pin is not NULL before using it and log an error if it is because this is unexpected. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Eric Yang <eric.yang2@amd.com> Acked-by: Anson Jacob <anson.jacob@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-01-20drm/amd/display: Allow dmub srv hardware reset before HW initNicholas Kazlauskas1-3/+0
[Why] We need hardware reset before hardware init for backdoor loading when we're reusing the framebuffer memory. [How] This doesn't run if the hardware isn't already in reset from software perspective. The reset function has register level checks so just remove the software one here. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Eric Yang <eric.yang2@amd.com> Acked-by: Anson Jacob <anson.jacob@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2021-01-20drm/amd/display: Report Freesync to vrr_range debugfs entry in DRMStylon Wang1-0/+4
[Why] Since Linux 5.9.0, DRM has provided vrr_range debugfs for all connectors. Reporting Freesync capability to vrr_range debugfs entry registered in Linux DM no longer works. [How] Report min/max vertical frequency to vrr_range debugfs entrry created by DRM connectors. Remove vrr_range debugfs entry from Linux DM. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Stylon Wang <stylon.wang@amd.com> Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by: Anson Jacob <anson.jacob@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Copyright © 1996 – 2026 Jason A. Donenfeld. All Rights Reverse Engineered.