| Age | Commit message (Collapse) | Author | Files | Lines |
|
[Why]
It's possible for some fallback scenarios to result in infinite looping
during link training.
[How]
This change modifies DP LT fallback behavior to more closely match the
DP standard. Keep track of the link rate during the EQ_FAIL fallback,
and use it as the maximum link rate for the CR sequence.
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Ilya <Ilya.Bakoulin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Description]
ref_dtbclk value is assigned in clk_mgr_construct,
but the clks struct is cleared in init_clocks.
Make sure to restore the value or we will get
0 value for ref_dtbclk in DCN31.
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
DMUB Outbox0 read/write pointer not sync after resumed from S4.
And that caused old traces were sent to outbox.
[How]
Disable DMUB Outbox0 interrupt
and clear DMUB Outbox0 read/write pointer when resumes from S4.
And then enable Outbox0 interrupt before starts DMCUB.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Very low rate to cause memory access issue while resetting
DMCUB after the halt command was sent to it.
The process of stopping fw of DMCUB may be timeout, that means
it is not in idle state, such as the window frames may still be
kept in cache, so reset by force will cause MMHUB hang.
[HOW]
After the halt command was sent, keep checking the DMCUB state until
it is idle.
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: hengzhou <Hengyong.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
When enabling an HPO stream for the first time after having previously
enabled a DIO stream there may be lingering DIO FIFO errors even though
the DIO is no longer enabled.
These can cause display clock change to hang if we don't apply the
OTG disable workaround since the ramping logic is tied to OTG on.
[How]
The workaround wasn't being applied in the sequence of:
1 DIO stream
0 streams
1 HPO stream
because current_state has no stream or planes in its context - and
it's only swapped after optimize has finished.
We should be using the incoming context instead to determine whether
this logic is needed or not.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
why and how:
Revert this change. It was causing a black screen with certain blocks
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Leung, Martin <Martin.Leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Dmub read AUX_DPHY_RX_CONTROL0 from Golden Setting Table,
but driver will set it to default value 0x103d1110, which
causes issue in some case
[How]
Remove the driver code, use the value set by dmub in
dp_aux_init
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Sherry Wang <YAO.WANG1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
According to the KMS man page, there is a
"Coverage" alpha blend mode that assumes the
pixel color values have NOT been pre-multiplied
and will be done when the actual blending to
the background color values happens.
Previously, this mode hasn't been enabled
in our driver and it was assumed that all
normal overlay planes are pre-multiplied
by default.
When a 3rd party app is used to input a image
in a specific format, e.g. PNG, as a source
of a overlay plane to blend with the background
primary plane, the pixel color values are not
pre-multiplied. So by adding "Coverage" blend
mode, our driver will support those cases.
Issue fixed: Overlay plane alpha channel blending is incorrect
Issue tracker: https://gitlab.freedesktop.org/drm/amd/-/issues/1769
Reference:
https://dri.freedesktop.org/docs/drm/gpu/drm-kms.html#plane-composition-properties
Adding Coverage support also enables IGT
kms_plane_alpha_blend Coverage subtests:
1. coverage-7efc
2. coverage-vs-premult-vs-constant
Changes
1. Add DRM_MODE_BLEND_COVERAGE blend mode capability
2. Add "pre_multiplied_alpha" flag for Coverage case
3. Read the correct flag and set the DCN MPCC
pre_multiplied register bit (only on overlay plane)
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1769
Signed-off-by: Sung Joon Kim <Sungjoon.Kim@amd.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The > ARRAY_SIZE() should be >= ARRAY_SIZE() to prevent an out of bounds
access.
Fixes: e27c41d5b068 ("drm/amd/display: Support for DMUB HPD interrupt handling")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This version brings along the following:
- Improvements in link training fallback
- Adding individual edp hotplug support
- Fixes in DPIA HPD status, display clock change hang, etc.
- FPU isolation work for DCN30
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This reverts commit 3b90318d44f87a3582f876802253a7748d270385.
[WHY]
Regressions unintentionally caused by change,
reverting until this can be resolved.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
we save the prev_dppclk value using "dpp_inst" but
when reading this value we use the index "i". In
a case where a pipe is fused off we can end up reading
the incorrect instance because i != dpp_inst in this
case.
[How]
read the prev_dppclk using dpp_inst instead of i
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why & how]
As part of the FPU isolation work documented in
https://patchwork.freedesktop.org/series/93042/, isolate
code that uses FPU in DCN30 to DML, where all FPU code
should locate.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
A display clock change hang can occur when switching between DIO and HPO
enabled modes during the optimize_bandwidth in dc_commit_state_no_check
call.
This happens when going from 4k120 8bpc 420 to 4k144 10bpc 444.
Display clock in the DIO case is 1200MHz, but pixel rate is 600MHz
because the pixel format is 420.
Display clock in the HPO case is less (800MHz?) because of ODM combine
which results in a smaller divider.
The DIO is still active in prepare but not active in the optimize which
results in the hang occuring.
During this change there are no planes on the stream so it's safe to
apply the workaround, but dpms_off = false and signal type is not
virtual.
[How]
Check for plane_count == 0, no planes on the stream.
It's easiest to check pipe->plane_state == NULL as an equivalent check
rather than trying to search for the stream status in the context
associated with the stream, so let's do that.
The primary, non MPO pipe should not have a NULL plane state.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Second eDP can send display off notification through HPD
but DC isn't hooked up to handle. Some primary eDP panels
will toggle on/off incorrectly if it's enabled generically.
[How]
Extend the debug option to allow individually enabling hotplug
either the first eDP or the second eDP in a dual eDP system.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[How & Why]
If a value of 0 is read, then this will cause a divide-by-0 panic.
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
when driver and dmub request aux engine at the same time,
dmub grant the aux engine but driver fail. Then driver
release aux engine but doesn't clear the request bit.
Then aux engine will be occupied by driver forever.
[How]
When driver release aux engine, clear request bit as well.
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
Code clean up in dc.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Driver needs up to date DPIA HPD status.
[How]
Use HPD query command to get DPIA HPD status.
Reviewed-by: Meenakshikumar Somasundaram <Meenakshikumar.Somasundaram@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Some displays may need several link training attempts before
link training succeeds.
[How]
If training succeeds after falling back to lower link bandwidth,
retry at original link bandwidth instead of abandoning link training
whenever link bandwidth is less than stream bandwidth.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Pull drm updates from Dave Airlie:
"Intel have enabled DG2 on certain SKUs for laptops, AMD has started
some new GPU support, msm has user allocated VA controls
dma-buf:
- add dma_resv_replace_fences
- add dma_resv_get_singleton
- make dma_excl_fence private
core:
- EDID parser refactorings
- switch drivers to drm_mode_copy/duplicate
- DRM managed mutex initialization
display-helper:
- put HDMI, SCDC, HDCP, DSC and DP into new module
gem:
- rework fence handling
ttm:
- rework bulk move handling
- add common debugfs for resource managers
- convert to kvcalloc
format helpers:
- support monochrome formats
- RGB888, RGB565 to XRGB8888 conversions
fbdev:
- cfb/sys_imageblit fixes
- pagelist corruption fix
- create offb platform device
- deferred io improvements
sysfb:
- Kconfig rework
- support for VESA mode selection
bridge:
- conversions to devm_drm_of_get_bridge
- conversions to panel_bridge
- analogix_dp - autosuspend support
- it66121 - audio support
- tc358767 - DSI to DPI support
- icn6211 - PLL/I2C fixes, DT property
- adv7611 - enable DRM_BRIDGE_OP_HPD
- anx7625 - fill ELD if no monitor
- dw_hdmi - add audio support
- lontium LT9211 support, i.MXMP LDB
- it6505: Kconfig fix, DPCD set power fix
- adv7511 - CEC support for ADV7535
panel:
- ltk035c5444t, B133UAN01, NV3052C panel support
- DataImage FG040346DSSWBG04 support
- st7735r - DT bindings fix
- ssd130x - fixes
i915:
- DG2 laptop PCI-IDs ("motherboard down")
- Initial RPL-P PCI IDs
- compute engine ABI
- DG2 Tile4 support
- DG2 CCS clear color compression support
- DG2 render/media compression formats support
- ATS-M platform info
- RPL-S PCI IDs added
- Bump ADL-P DMC version to v2.16
- Support static DRRS
- Support multiple eDP/LVDS native mode refresh rates
- DP HDR support for HSW+
- Lots of display refactoring + fixes
- GuC hwconfig support and query
- sysfs support for multi-tile
- fdinfo per-client gpu utilisation
- add geometry subslices query
- fix prime mmap with LMEM
- fix vm open count and remove vma refcounts
- contiguous allocation fixes
- steered register write support
- small PCI BAR enablement
- GuC error capture support
- sunset igpu legacy mmap support for newer devices
- GuC version 70.1.1 support
amdgpu:
- Initial SoC21 support
- SMU 13.x enablement
- SMU 13.0.4 support
- ttm_eu cleanups
- USB-C, GPUVM updates
- TMZ fixes for RV
- RAS support for VCN
- PM sysfs code cleanup
- DC FP rework
- extend CG/PG flags to 64-bit
- SI dpm lockdep fix
- runtime PM fixes
amdkfd:
- RAS/SVM fixes
- TLB flush fixes
- CRIU GWS support
- ignore bogus MEC signals more efficiently
msm:
- Fourcc modifier for tiled but not compressed layouts
- Support for userspace allocated IOVA (GPU virtual address)
- DPU: DSC (Display Stream Compression) support
- DP: eDP support
- DP: conversion to use drm_bridge and drm_bridge_connector
- Merge DPU1 and MDP5 MDSS driver
- DPU: writeback support
nouveau:
- make some structures static
- make some variables static
- switch to drm_gem_plane_helper_prepare_fb
radeon:
- misc fixes/cleanups
mxsfb:
- rework crtc mode setting
- LCDIF CRC support
etnaviv:
- fencing improvements
- fix address space collisions
- cleanup MMU reference handling
gma500:
- GEM/GTT improvements
- connector handling fixes
komeda:
- switch to plane reset helper
mediatek:
- MIPI DSI improvements
omapdrm:
- GEM improvements
qxl:
- aarch64 support
vc4:
- add a CL submission tracepoint
- HDMI YUV support
- HDMI/clock improvements
- drop is_hdmi caching
virtio:
- remove restriction of non-zero blob types
vmwgfx:
- support for cursormob and cursorbypass 4
- fence improvements
tidss:
- reset DISPC on startup
solomon:
- SPI support
- DT improvements
sun4i:
- allwinner D1 support
- drop is_hdmi caching
imx:
- use swap() instead of open-coding
- use devm_platform_ioremap_resource
- remove redunant initializations
ast:
- Displayport support
rockchip:
- Refactor IOMMU initialisation
- make some structures static
- replace drm_detect_hdmi_monitor with drm_display_info.is_hdmi
- support swapped YUV formats,
- clock improvements
- rk3568 support
- VOP2 support
mediatek:
- MT8186 support
tegra:
- debugabillity improvements"
* tag 'drm-next-2022-05-25' of git://anongit.freedesktop.org/drm/drm: (1740 commits)
drm/i915/dsi: fix VBT send packet port selection for ICL+
drm/i915/uc: Fix undefined behavior due to shift overflowing the constant
drm/i915/reg: fix undefined behavior due to shift overflowing the constant
drm/i915/gt: Fix use of static in macro mismatch
drm/i915/audio: fix audio code enable/disable pipe logging
drm/i915: Fix CFI violation with show_dynamic_id()
drm/i915: Fix 'mixing different enum types' warnings in intel_display_power.c
drm/i915/gt: Fix build error without CONFIG_PM
drm/msm/dpu: handle pm_runtime_get_sync() errors in bind path
drm/msm/dpu: add DRM_MODE_ROTATE_180 back to supported rotations
drm/msm: don't free the IRQ if it was not requested
drm/msm/dpu: limit writeback modes according to max_linewidth
drm/amd: Don't reset dGPUs if the system is going to s2idle
drm/amdgpu: Unmap legacy queue when MES is enabled
drm: msm: fix possible memory leak in mdp5_crtc_cursor_set()
drm/msm: Fix fb plane offset calculation
drm/msm/a6xx: Fix refcount leak in a6xx_gpu_init
drm/msm/dsi: don't powerup at modeset time for parade-ps8640
drm/rockchip: Change register space names in vop2
dt-bindings: display: rockchip: make reg-names mandatory for VOP2
...
|
|
Pull Wstringop-overflow fixes from Gustavo Silva:
"Fix some -Wstringop-overflow warnings when building with GCC-11. All
the patches have been in linux-next during the last development cycle.
This is part of the ongoing efforts to globally enable
-Wstringop-overflow"
* tag 'Wstringop-overflow-fixes-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
drm/i915: Fix -Wstringop-overflow warning in call to intel_read_wm_latency()
drm/amd/display: Fix Wstringop-overflow warnings in dc_link_dp.c
scsi: fcoe: Fix Wstringop-overflow warnings in fcoe_wwn_from_mac()
|
|
As drm_connector already have the display_info, instead of creating
"output_bpc" debugfs in vendor specific driver, move the logic to
the drm layer.
This patch will also move "Current" bpc to the crtc debugfs from
connector debugfs, since we are getting this info from crtc_state.
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Bhanuprakash Modem <bhanuprakash.modem@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220519095149.3560034-4-bhanuprakash.modem@intel.com
|
|
amd-drm-next-5.19-2022-05-18:
amdgpu:
- Misc code cleanups
- Additional SMU 13.x enablement
- Smartshift fixes
- GFX11 fixes
- Support for SMU 13.0.4
- SMU mutex fix
- Suspend/resume fix
amdkfd:
- static checker fix
- Doorbell/MMIO resource handling fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220518205621.5741-1-alexander.deucher@amd.com
|
|
Eliminate the follow smatch warning:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:9687
amdgpu_dm_atomic_commit_tail() warn: inconsistent indenting.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This gives us the standard atomic implicit and explicit fencing rules.
v2: move the wait to amdgpu_dm_atomic_commit_tail
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Roman Li <Roman.Li@amd.com>
Cc: Qingqing Zhuo <qingqing.zhuo@amd.com>
Cc: Jude Shih <shenshih@amd.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220509074712.163899-1-christian.koenig@amd.com
|
|
This version brings along following fixes:
- Refactor LTTPR code
- Fix PSR after hibernate
- Fix DC build errors
- Fix IRQ unregister error when unloading amdgpu
- Improve DP link training
- Fix stutter
- Remove redundant CONFIG_DRM_AMD_DC_DCN guards
- Fix 2nd connected USB-C display not lighting up
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This reverts commit 4b7786d87fb3adf3e534c4f1e4f824d8700b786b.
Commit 4b7786d87fb3 ("drm/amd/display: Fix DCN3 B0 DP Alt Mapping")
is causing 2nd USB-C display not lighting up.
Phy id remapping is done differently than is assumed in this
patch.
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
CONFIG_DRM_AMD_DC_DCN is used by pass the compilation failures, but DC
code should be OS-agnostic.
This patch fixes it by removing unnecessasry CONFIG_DRM_AMD_DC_DCN
guards for #if-#else clause.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
CONFIG_DRM_AMD_DC_DCN is used by pass the compilation failures, but DC
code should be OS-agnostic.
This patch fixes it by removing unnecessasry CONFIG_DRM_AMD_DC_DCN
in amdgpu_dm directory.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
CONFIG_DRM_AMD_DC_DCN is used by pass the compilation failures, but DC
code should be OS-agnostic.
This patch fixes it by removing unnecessasry CONFIG_DRM_AMD_DC_DCN
for enabling z10.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
CONFIG_DRM_AMD_DC_DCN is used by pass the compilation failures, but DC
code should be OS-agnostic.
This patch fixes it by removing unnecessasry CONFIG_DRM_AMD_DC_DCN
in irq directory.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
CONFIG_DRM_AMD_DC_DCN is used by pass the compilation failures, but DC
code should be OS-agnostic.
This patch fixes it by removing unnecessasry CONFIG_DRM_AMD_DC_DCN
in gpio directory.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
CONFIG_DRM_AMD_DC_DCN is used by pass the compilation failures, but DC
code should be OS-agnostic.
This patch fixes it by removing unnecessasry CONFIG_DRM_AMD_DC_DCN
in dce directory.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
CONFIG_DRM_AMD_DC_DCN is used by pass the compilation failures, but DC
code should be OS-agnostic.
This patch fixes it by removing unnecessasry CONFIG_DRM_AMD_DC_DCN
in dc and dc/core directories.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Waiting for the vlbank every time a global sync update is requested,
including during full update flips, results in a stutter.
[How]
Do not wait for vblank during pipe programming.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
There is a chance where the RX issues HPD deassert in the
middle of link training, this will cause our logic to
abort link training and turn off link. However our payload
allocation logic needs to use current link settings to
determine average time slot per MTP. This will need to
use current link bandwidth as divider. This causes divide
by zero error occasionally. The fix is to skip DP2.0 payload
allocation logic if current link is not in 128b/132b mode.
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
Observing error log about trying to disable non-implemented irq source
when user unload the driver.
[how]
Check and filter the invalid irq source before disabling it.
Reviewed-by: Qingqing (Lillian) Zhuo <Qingqing.Zhuo@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alan Liu <HaoPing.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
Move definition of dc_flip_addrs struct from dc.h to dc_hw_types.h to
prevent build errors
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
After hibernate system might be using old invalid psr_power_opt and
psr_allow_active that never get reset
[HOW]
Reset cached Panel Self Refresh parameters when PSR is first configured
for eDP in dc_link_setup_psr.
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Evgenii Krasnikov <Evgenii.Krasnikov@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Split LTTPR mode selection between platform support and downstream link support
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Z10 and S0i3 have some shared path. Previous code clean up ,
incorrectly removed these pointers, which breaks s0i3 restore
[How]
Do not clear the function pointers based on Z10 disable.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
amd-drm-next-5.19-2022-04-29:
amdgpu
- RAS updates
- SI dpm deadlock fix
- Misc code cleanups
- HDCP fixes
- PSR fixes
- DSC fixes
- SDMA doorbell cleanups
- S0ix fix
- DC FP fix
- Zen dom0 regression fix for APUs
- IP discovery updates
- Initial SoC21 support
- Support for new vbios tables
- Runtime PM fixes
- Add PSP TA debugfs interface
amdkfd:
- Misc code cleanups
- Ignore bogus MEC signals more efficiently
- SVM fixes
- Use bitmap helpers
radeon:
- Misc code cleanups
- Spelling/grammer fixes
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220429144853.5742-1-alexander.deucher@amd.com
|
|
A faulty receiver might report an erroneous channel count. We
should guard against reading beyond AUDIO_CHANNELS_COUNT as
that would overflow the dpcd_pattern_period array.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
This version brings along following fixes:
- Have optc3 function accessible to newer DCN
- Add CM boot option for USB4 tunneling
- Fix system hang issue when game resolution is changed
- Remove outdated register for dcn3+
- Add new DSC interface to disconnect from pipe
- Clean up pixel format types in enum surface_pixel_format
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
- Add new cmd for querying HPD state
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
Equate the first non-subsampled video surface format to
the enum SURFACE_PIXEL_FORMAT_SUBSAMPLE_END since it's
not a real format.
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
Add new DSC interface to disconnect from pipe.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
Remove MPCC_OGAM_LUT_RAM_CONTROL register which is outdated.
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Tse Kaitlyn <Kaitlyn.Tse@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This reverts commit d2069326d26c7de78e77a060fb6e6d0d21c35dbd.
Commit d2069326d26c ("drm/amd/display: Reset cached PSR parameters after hibernate")
causes a system hang when game resolution is changed. Revert it.
Reviewed-by: Jayendran Ramani <Jayendran.Ramani@amd.com>
Reviewed-by: Harry Vanzylldejong <Harry.Vanzylldejong@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Evgenii Krasnikov <Evgenii.Krasnikov@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|