| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
skl+ can go belly up if there are overlapping ddb allocations between
planes. If we could absolutely guarantee that we can perform the atomic
update within a single frame we shouldn't have to worry about this. But
we can't rely on that so let's steal the ddb overlap check trick from
skl_update_crtcs() and apply it to the plane updates. Since each step
of the sequence is free from ddb overlaps we don't have to worry about
a vblank sneaking up on us in the middle of the sequence. The partial
state that gets latched by the hardware will be safe. And unlike
skl_update_crtcs() we don't have to intoduce any extra vblank waits
on account of only having to worry about a single pipe.
v2: Fix typo in commit msg (Matt)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-12-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
|
|
We're going to need access to the new crtc state in ->disable_plane()
for SKL+ wm/ddb programming and pre-skl pipe gamma/csc control. Pass
the crtc state down.
We'll also try to make intel_crtc_disable_planes() do the right
thing as much as it's possible. The fact that we don't have a
separate crtc state for the disabled state when we're going to
re-enable the crtc later means we might end up poking at a few
extra planes in there. But that's harmless. I suppose one might
argue that we wouldn't have to care about proper ddb/wm/csc/gamma
if the pipe is going to permanently disable anyway, but the state
checker probably cares so we should try our best to make sure
everything is programmed correctly even in that case.
v2: Fix the commit message a bit (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-5-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
|
|
Keep track which planes need updating during the commit. For now
we set the bit for any plane that was or will be visible (including
icl+ nv12 slave planes). In the future I'll have need to update
invisible planes as well, for skl plane ddbs and for pre-skl pipe
gamma/csc control (which lives in the primary plane control register).
v2: Pimp the commit message to mention icl+ nv12 slave planes (Matt)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127163742.30215-1-ville.syrjala@linux.intel.com
|
|
Use intel_plane_destroy_state in intel_plane_free to free the state.
Also fix intel_plane_alloc() to use __drm_atomic_helper_plane_reset(),
to get sane defaults from the atomic core.
This is needed to get the correct alpha value and blend mode from the
core, and any new default values added from new properties.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: b20815255693 ("drm/i915: Add plane alpha blending support, v2.")
[mlankhorst: Update commit description to mention alpha blend support]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181113092804.13304-1-maarten.lankhorst@linux.intel.com
|
|
To make NV12 working on icl, we need to update 2 planes simultaneously.
I've chosen to do this in the CRTC step after plane validation is done,
so we know what planes are (in)visible. The linked Y plane will get
updated in intel_plane_update_planes_on_crtc(), by the call to
update_slave, which gets the master's plane_state as argument.
The link requires both planes for atomic_update to work,
so make sure skl_ddb_add_affected_planes() adds both states.
Changes since v1:
- Introduce icl_is_nv12_y_plane(), instead of hardcoding sprite numbers.
- Put all the state updating login in intel_plane_atomic_check_with_state().
- Clean up changes in intel_plane_atomic_check().
Changes since v2:
- Fix intel_atomic_get_old_plane_state() to actually return old state.
- Move visibility changes to preparation patch.
- Only try to find a Y plane on gen11, earlier platforms only require
a single plane.
Changes since v3:
- Fix checkpatch warning about to_intel_crtc() usage.
- Add affected planes from icl_add_linked_planes() before check_planes(),
it's a cleaner way to do this. (Ville)
Changes since v4:
- Clear plane links in icl_check_nv12_planes() for clarity.
- Only pass crtc_state to icl_check_nv12_planes().
- Use for_each_new_intel_plane_in_state() in icl_check_nv12_planes.
- Rename aux to linked. (Ville)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181022135152.15324-1-maarten.lankhorst@linux.intel.com
[mlankhorst: Change bool slave to u32, to satisfy checkpatch]
[mlankhorst: Add WARN_ON's based on Ville's suggestion]
|
|
No point in having each caller of intel_create_plane_state() initialize
the scaler_id to -1. Instead just do it in intel_create_plane_state().
Previously we left scaler_id at 0 for pre-SKL platforms, but I can't
see how initializing it to -1 always would cause any harm.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181005125817.22576-8-ville.syrjala@linux.intel.com
|
|
drm_atomic_helper_commit_planes_on_crtc calls begin_commit,
then plane_update hooks, then flush_commit. Because we keep our own
visibility tracking through plane_state->visible there's no need to
rely on the atomic hooks for this.
By explicitly writing our own helper, we can update visible planes
as needed, which is useful to make NV12 support work as intended.
Changes since v1:
- Reword commit message. (Matt Roper)
- Rename to intel_update_planes_on_crtc(). (Matt)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180920102711.4184-6-maarten.lankhorst@linux.intel.com
|
|
We need to assume the plane has been visible before, even if no CRTC
is assigned to the plane. This is because when enabling a nv12 plane
on gen11, we will have to enable an extra plane and make it visible
by marking it in crtc_state->active_planes for
intel_update_planes_on_crtc().
Additionally, clear visible flag in intel_plane_atomic_check, in case
we ever hit a bug with visibility. Our code implicitly assumes that
plane_state->visible is only true when crtc and fb are set,
so we will either null deref in intel_fbc_choose_crtc() or
do something bad during the actual commit which cares even more.
Changes since v1:
- Unconditionally clear crtc_state->active_planes as well.
- Reword commit message, since this is now a preparation patch for
NV12 Y / UV plane linking.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[mlankhorst: Clear nv12_planes in the beginning as well, clarify commit message]
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180920102711.4184-4-maarten.lankhorst@linux.intel.com
|
|
Move the chv rotation vs. reflections checks to the plane->check() hook,
away from the (now) platform agnostic
intel_plane_atomic_check_with_state().
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180907152413.15761-13-ville.syrjala@linux.intel.com
|
|
Move the skl+ specific framebuffer related checks from
intel_plane_atomic_check_with_state() into a new function
(skl_plane_check_fb()) which we'll simply call from the skl
plane->check() hook.
v2: Split out the Y/Yf+CCS vs. interlaced change (José)
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180907152413.15761-11-ville.syrjala@linux.intel.com
|
|
Y/Yf tiling can't be used with IF-ID. We already reject uncompressed
Y/Yf but we should also reject them when compressed.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180828142707.31583-2-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Mahesh Kumar <mahesh1.sh.kumar@gmail.com>
|
|
.check_plane() already gets the plane state, so we can dig out the plane
from there if needed. No need in passing it separately.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180828142707.31583-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
|
|
Chris is doing many reworks that allow us to get full-ppgtt supported
on all platforms back to HSW. As well many other fix and improvements,
Including:
- Use GEM suspend when aborting initialization (Chris)
- Change i915_gem_fault to return vm_fault_t (Chris)
- Expand VMA to Non gem object entities (Chris)
- Improve logs for load failure, but quite logging on fault injection to avoid noise on CI (Chris)
- Other page directory handling fixes and improvements for gen6 (Chris)
- Other gtt clean-up removing redundancies and unused checks (Chris)
- Reorder aliasing ppgtt fini (Chris)
- Refactor of unsetting obg->mm.pages (Chris)
- Apply batch location restrictions before pinning (Chris)
- Ringbuffer fixes for context restore (Chris)
- Execlist fixes on freeing error pointer on allocation error (Chris)
- Make closing request flush mandatory (Chris)
- Move GEM sanitize from resume_early to resume (Chris)
- Improve debug dumps (Chris)
- Silent compiler for selftest (Chris)
- Other execlists changes to improve hangcheck and reset.
- Many gtt page directory fixes and improvements (Chris)
- Reorg context workarounds (Chris)
- Avoid ERR_PTR dereference on selftest (Chris)
Other GEM related work:
- Stop trying to reset GPU if reset failed (Mika)
- Add HW workaround for KBL to fix GPU reset (Mika)
- Fix context ban and hang accounting for client (Mika)
- Fixes on OA perf (Michel, Jani)
- Refactor on GuC log mechanisms (Piotr)
- Enable provoking vertex fix on Gen9 system (Kenneth)
More ICL patches for Display enabling:
- ICL - 10-bit support for HDMI (RK)
- ICL - Start adding TBT PLL (Paulo)
- ICL - DDI HDMK level selection (Manasi)
- ICL - GMBUS GPIO pin mapping fix (Mahesh)
- ICL - Adding DP_AUX_E support (James)
- ICL - Display interrupts handling (DK)
Other display fixes and improvements:
- Fix sprite destination color keying on SKL+ (Ville)
- Fixes and improvements on PCH detection, specially for non PCH systems (Jani)
- Document PCH_NOP (Lucas)
- Allow DBLSCAN user modes with eDP/LVDS/DSI (Ville)
- Opregion and ACPI cleanup and organization (Jani)
- Kill delays when activation psr (Rodrigo)
- ...and a consequent fix of the psr activation flow (DK)
- Fix HDMI infoframe setting (Imre)
- Fix Display interrupts and modes on old gens (Ville)
- Start switching to kernel unsigned int types (Jani)
- Introduction to Amber Lake and Whiskey Lake platforms (Jose)
- Audio clock fixes for HBR3 (RK)
- Standardize i915_reg.h definitions according to our doc and checkpatch (Paulo)
- Remove unused timespec_to_jiffies_timeout function (Arnd)
- Increase the scope of PSR wake fix for other VBTs out there (Vathsala)
- Improve debug msgs with prop name/id (Ville)
- Other clean up on unecessary cursor size defines (Ville)
- Enforce max hdisplay/hblank_start limits on HSW/BDW (Ville)
- Make ELD pointers constant (Jani)
- Fix for PSR VBT parse (Colin)
- Add warn about unsupported CDCLK rates (Imre)
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Thu 21 Jun 2018 07:12:10 AM AEST
# gpg: using RSA key FA625F640EEB13CA
# gpg: Good signature from "Rodrigo Vivi <rodrigo.vivi@intel.com>"
# gpg: aka "Rodrigo Vivi <rodrigo.vivi@gmail.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6D20 7068 EEDD 6509 1C2C E2A3 FA62 5F64 0EEB 13CA
Link: https://patchwork.freedesktop.org/patch/msgid/20180625165622.GA21761@intel.com
|
|
We got a few conflicts in drm_atomic.c after merging the DRM writeback support,
now we need a backmerge to unlock develop development on drm-misc-next.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
|
|
Use the '[PROP:id:name]' format I introduced for the core in the driver
debug messages as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611193403.16118-3-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We want to get rid of plane->fb/crtc on atomic drivers. Stop setting
them.
v2: Fix up the comment in intel_crtc_active() and
nuke the rest of the stale comments (Daniel)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #v1
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180525185045.29689-9-ville.syrjala@linux.intel.com
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
|
|
The workaround was applied only to the primary plane, but is required
on all planes. Iterate over all planes in the crtc atomic check to see
if the workaround is enabled, and only perform the actual toggling in
the pre/post plane update functions.
Changes since v1:
- Track active NV12 planes in a nv12_planes bitmask. (Ville)
v2: Removing BROXTON support for NV12 due to WA826
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1526074397-10457-2-git-send-email-vidya.srinivas@intel.com
|
|
Driver Changes:
- Lift alpha_support protection from Cannonlake (Rodrigo)
* Meaning the driver should mostly work for the hardware we had
at our disposal when testing
* Used to be preliminary_hw_support
- Add missing Cannonlake PCI device ID of 0x5A4C (Rodrigo)
- Cannonlake port register fix (Mahesh)
- Fix Dell Venue 8 Pro black screen after modeset (Hans)
- Fix for always returning zero out-fence from execbuf (Daniele)
- Fix HDMI audio when no no relevant video output is active (Jani)
- Fix memleak of VBT data on driver_unload (Hans)
- Fix for KASAN found locking issue (Maarten)
- RCU barrier consolidation to improve igt/gem_sync/idle (Chris)
- Optimizations to IRQ handlers (Chris)
- vblank tracking improvements (64-bit resolution, PM) (Dhinakaran)
- Pipe select bit corrections (Ville)
- Reduce runtime computed device_info fields (Chris)
- Tune down some WARN_ONs to GEM_BUG_ON now that CI has good coverage (Chris)
- A bunch of kerneldoc warning fixes (Chris)
* tag 'drm-intel-next-2018-02-21' of git://anongit.freedesktop.org/drm/drm-intel: (113 commits)
drm/i915: Update DRIVER_DATE to 20180221
drm/i915/fbc: Use PLANE_HAS_FENCE to determine if the plane is fenced
drm/i915/fbdev: Use the PLANE_HAS_FENCE flags from the time of pinning
drm/i915: Move the policy for placement of the GGTT vma into the caller
drm/i915: Also check view->type for a normal GGTT view
drm/i915: Drop WaDoubleCursorLP3Latency:ivb
drm/i915: Set the primary plane pipe select bits on gen4
drm/i915: Don't set cursor pipe select bits on g4x+
drm/i915: Assert that we don't overflow frontbuffer tracking bits
drm/i915: Track number of pending freed objects
drm/i915/: Initialise trans_min for skl_compute_transition_wm()
drm/i915: Clear the in-use marker on execbuf failure
drm/i915: Prune gen8_gt_irq_handler
drm/i915: Track GT interrupt handling using the master iir
drm/i915: Remove WARN_ONCE for failing to pm_runtime_if_in_use
drm: intel_dpio_phy: fix kernel-doc comments at nested struct
drm/i915: Release connector iterator on a digital port conflict.
drm/i915/execlists: Remove too early assert
drm/i915: Assert that we always complete a submission to guc/execlists
drm: move read_domains and write_domain into i915
...
|
|
Currently we make the unilateral decision inside
i915_gem_object_pin_to_display() where the VMA should resided (inside
the fence and mappable region or above?). This is not our decision to
make as it impacts on how the display engine can use the resulting
scanout object, and it would rather instruct us where to place the VMA so
that it can enable the features it wants. As such, make the pin flags an
argument to i915_gem_object_pin_to_display() and control them from
intel_pin_and_fence_fb_obj()
Whilst taking control of the mapping for ourselves, start tracking how
we use it to avoid trying to free a fence we never claimed:
<3>[ 227.151869] GEM_BUG_ON(vma->fence->pin_count <= 0)
<4>[ 227.152064] ------------[ cut here ]------------
<2>[ 227.152068] kernel BUG at drivers/gpu/drm/i915/i915_vma.h:391!
<4>[ 227.152084] invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
<0>[ 227.152092] Dumping ftrace buffer:
<0>[ 227.152099] (ftrace buffer empty)
<4>[ 227.152102] Modules linked in: i915 snd_hda_codec_analog snd_hda_codec_generic coretemp snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core snd_pcm lpc_ich e1000e mei_me mei prime_numbers
<4>[ 227.152131] CPU: 1 PID: 1587 Comm: kworker/u16:49 Tainted: G U 4.16.0-rc1-gbab67b2f6177-kasan_7+ #1
<4>[ 227.152134] Hardware name: Dell Inc. OptiPlex 755 /0PU052, BIOS A08 02/19/2008
<4>[ 227.152236] Workqueue: events_unbound intel_atomic_commit_work [i915]
<4>[ 227.152292] RIP: 0010:intel_unpin_fb_vma+0x23a/0x2a0 [i915]
<4>[ 227.152295] RSP: 0018:ffff88005aad7b68 EFLAGS: 00010286
<4>[ 227.152300] RAX: 0000000000000026 RBX: ffff88005c359580 RCX: 0000000000000000
<4>[ 227.152304] RDX: 0000000000000026 RSI: ffffffff8707d840 RDI: ffffed000b55af63
<4>[ 227.152307] RBP: ffff880056817e58 R08: 0000000000000001 R09: 0000000000000000
<4>[ 227.152311] R10: ffff88005aad7b88 R11: 0000000000000000 R12: ffff8800568184d0
<4>[ 227.152314] R13: ffff880065b5ab08 R14: 0000000000000000 R15: dffffc0000000000
<4>[ 227.152318] FS: 0000000000000000(0000) GS:ffff88006ac40000(0000) knlGS:0000000000000000
<4>[ 227.152322] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
<4>[ 227.152325] CR2: 00007f5fb25550a8 CR3: 0000000068c78000 CR4: 00000000000006e0
<4>[ 227.152328] Call Trace:
<4>[ 227.152385] intel_cleanup_plane_fb+0x6b/0xd0 [i915]
<4>[ 227.152395] drm_atomic_helper_cleanup_planes+0x166/0x280
<4>[ 227.152452] intel_atomic_commit_tail+0x159d/0x3380 [i915]
<4>[ 227.152463] ? process_one_work+0x66e/0x1460
<4>[ 227.152516] ? skl_update_crtcs+0x9c0/0x9c0 [i915]
<4>[ 227.152523] ? lock_acquire+0x13d/0x390
<4>[ 227.152527] ? lock_acquire+0x13d/0x390
<4>[ 227.152534] process_one_work+0x71a/0x1460
<4>[ 227.152540] ? __schedule+0x815/0x1e20
<4>[ 227.152547] ? pwq_dec_nr_in_flight+0x2b0/0x2b0
<4>[ 227.152553] ? _raw_spin_lock_irq+0xa/0x40
<4>[ 227.152559] worker_thread+0xdf/0xf60
<4>[ 227.152569] ? process_one_work+0x1460/0x1460
<4>[ 227.152573] kthread+0x2cf/0x3c0
<4>[ 227.152578] ? _kthread_create_on_node+0xa0/0xa0
<4>[ 227.152583] ret_from_fork+0x3a/0x50
<4>[ 227.152591] Code: c6 00 11 86 c0 48 c7 c7 e0 bd 85 c0 e8 60 e7 a9 c4 0f ff e9 1f fe ff ff 48 c7 c6 40 10 86 c0 48 c7 c7 e0 ca 85 c0 e8 2b 95 bd c4 <0f> 0b 48 89 ef e8 4c 44 e8 c4 e9 ef fd ff ff e8 42 44 e8 c4 e9
<1>[ 227.152720] RIP: intel_unpin_fb_vma+0x23a/0x2a0 [i915] RSP: ffff88005aad7b68
v2: i915_vma_pin_fence() is a no-op if a fence isn't required, so check
vma->fence as well.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180220134208.24988-2-chris@chris-wilson.co.uk
|
|
drm-misc-next for 4.17:
UAPI Changes:
- drm/vc4: Expose performance counters to userspace (Boris)
Cross-subsystem Changes:
- MAINTAINERS: Linus to maintain panel-arm-versatile in -misc (Linus)
Core Changes:
- Only use swiotlb when necessary (Chunming)
Driver Changes:
- drm/panel: Add support for ARM Versatile panels (Linus)
- pl111: Improvements around versatile panel support (Linus)
----------------------------------------
Tagged on 2018-02-06:
drm-misc-next for 4.17:
UAPI Changes:
- Validate mode flags + type (Ville)
- Deprecate unused mode flags PIXMUX, BCAST (Ville)
- Deprecate unused mode types BUILTIN, CRTC_C, CLOCK_C, DEFAULT (Ville)
Cross-subsystem Changes:
- MAINTAINERS: s/Daniel/Maarten/ for drm-misc (Daniel)
Core Changes:
- gem: Export gem functions for drivers to use (Samuel)
- bridge: Introduce bridge timings in drm_bridge (Linus)
- dma-buf: Allow exclusive fence to be bundled in fence array when
calling reservation_object_get_fences_rcu (Christian)
- dp: Add training pattern 4 and HBR3 support to dp helpers (Manasi)
- fourcc: Add alpha bit to formats to avoid driver format LUTs (Maxime)
- mode: Various cleanups + add new device-wide .mode_valid hook (Ville)
- atomic: Fix state leak when non-blocking commits fail (Leo)
NOTE: IIRC, this was cross-picked to -fixes so it might fall out
- crc: Allow polling on the data fd (Maarten)
Driver Changes:
- bridge/vga-dac: Add THS8134* support (Linus)
- tinydrm: Various MIPI DBI improvements/cleanups (Noralf)
- bridge/dw-mipi-dsi: Cleanups + use create_packet helper (Brian)
- drm/sun4i: Add Display Engine frontend support (Maxime)
- drm/sun4i: Add zpos support + increase num planes from 2 to 4 (Maxime)
- various: Use drm_mode_get_hv_timing() to fill plane clip rectangle (Ville)
- stm: Add 8-bit clut support, add dsi phy v1.31 support, +fixes (Phillipe)
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Chunming Zhou <david1.zhou@amd.com>
Cc: Samuel Li <Samuel.Li@amd.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Brian Norris <briannorris@chromium.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
* tag 'drm-misc-next-2018-02-13' of git://anongit.freedesktop.org/drm/drm-misc: (115 commits)
drm/radeon: only enable swiotlb path when need v2
drm/amdgpu: only enable swiotlb alloc when need v2
drm: add func to get max iomem address v2
drm/vc4: Expose performance counters to userspace
drm: Print the pid when debug logging an ioctl error.
drm/stm: ltdc: remove non-alpha color formats on layer 2 for older hw
drm/stm: ltdc: add non-alpha color formats
drm/bridge/synopsys: dsi: Add 1.31 version support
drm/bridge/synopsys: dsi: Add read feature
drm/pl111: Support multiple endpoints on the CLCD
drm/pl111: Support variants with broken VBLANK
drm/pl111: Support variants with broken clock divider
drm/pl111: Handle the Versatile RGB/BGR565 mode
drm/pl111: Properly detect the ARM PL110 variants
drm/panel: Add support for ARM Versatile panels
drm/panel: Device tree bindings for ARM Versatile panels
drm/bridge: Rename argument from crtc to bridge
drm/crc: Add support for polling on the data fd.
drm/sun4i: Use drm_mode_get_hv_timing() to populate plane clip rectangle
drm/rcar-du: Use drm_mode_get_hv_timing() to populate plane clip rectangle
...
|
|
Deprecate the silly I915_SET_COLORKEY_NONE flag. The obvious
way to disable colorkey is to just set flags to 0, which is
exactly what the intel ddx has been doing all along.
Currently when userspace sets the flags to 0, we end up in a
funny state where colorkey is disabled, but various colorkey
vs. scaling checks still consider colorkey to be enabled, and
thus we don't allow plane scaling to kick in.
In case there is some other userspace out there that actually
uses this flag (unlikely as this is an i915 specific uapi)
we'll keep on accepting it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180202204231.27905-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.
No functional changes since pipe_src_w/h are already filled via
drm_mode_get_hv_timing().
Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123190502.28449-3-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Thierry Reding <treding@nvidia.com>
|
|
Eliminate plane->state and crtc->state usage from
intel_plane_atomic_check_with_state() and its callers. Instead pass the
proper states in or dig them up from the top level atomic state.
Note that intel_plane_atomic_check_with_state() itself isn't allowed to
use the top level atomic state as there is none when it gets called from
the legacy cursor short circuit path.
v2: Rename some variables for easier comprehension (Maarten)
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170823152226.22938-4-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
|
|
In Gen9 platform Interlaced fetch mode doesn't support following plane
configuration:
- Y/Yf tiling
- 90/270 rotation
- YUV420 hybrid planar source pixel formats.
This patch adds check to fail the flip if any of the above configuration
is requested.
Changes since V1:
- handle checks in intel_plane_atomic_check_with_state (ville)
- takeout plane scaler checks combile with pipe scaler in next patch
Changes since V2:
- No need to check for NV12 as it need scaling, so it will be rejected
by scaling check (ville)
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170630121100.20159-2-mahesh1.kumar@intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90238
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
|
|
More stuff for 4.13:
- skl+ wm fixes from Mahesh Kumar
- some refactor and tests for i915_sw_fence (Chris)
- tune execlist/scheduler code (Chris)
- g4x,g33 gpu reset improvements (Chris, Mika)
- guc code cleanup (Michal Wajdeczko, Michał Winiarski)
- dp aux backlight improvements (Puthikorn Voravootivat)
- buffer based guc/host communication (Michal Wajdeczko)
* tag 'drm-intel-next-2017-05-29' of git://anongit.freedesktop.org/git/drm-intel: (253 commits)
drm/i915: Update DRIVER_DATE to 20170529
drm/i915: Keep the forcewake timer alive for 1ms past the most recent use
drm/i915/guc: capture GuC logs if FW fails to load
drm/i915/guc: Introduce buffer based cmd transport
drm/i915/guc: Disable send function on fini
drm: Add definition for eDP backlight frequency
drm/i915: Drop AUX backlight enable check for backlight control
drm/i915: Consolidate #ifdef CONFIG_INTEL_IOMMU
drm/i915: Only GGTT vma may be pinned and prevent shrinking
drm/i915: Serialize GTT/Aperture accesses on BXT
drm/i915: Convert i915_gem_object_ops->flags values to use BIT()
drm/i915/selftests: Silence compiler warning in igt_ctx_exec
drm/i915/guc: Skip port assign on first iteration of GuC dequeue
drm/i915: Remove misleading comment in request_alloc
drm/i915/g33: Improve reset reliability
Revert "drm/i915: Restore lost "Initialized i915" welcome message"
drm/i915/huc: Update GLK HuC version
drm/i915: Check for allocation failure
drm/i915/guc: Remove action status and statistics from debugfs
drm/i915/g4x: Improve gpu reset reliability
...
|
|
Add DRM_MODE_ROTATE_ and DRM_MODE_REFLECT_ defines to the UAPI
as a convenience.
Ideally the DRM_ROTATE_ and DRM_REFLECT_ property ids are looked up
through the atomic API, but realizing that userspace is likely to take
shortcuts and assume that the enum values are what is sent over the
wire.
As a result these defines are provided purely as a convenience to
userspace applications.
Changes since v3:
- Switched away from past tense in comments
- Add define name change to previously mis-spelled DRM_REFLECT_X comment
- Improved the comment for the DRM_MODE_REFLECT_<axis> comment
Changes since v2:
- Changed define prefix from DRM_MODE_PROP_ to DRM_MODE_
- Fix compilation errors
- Changed comment formatting
- Deduplicated comment lines
- Clarified DRM_MODE_PROP_REFLECT_ comment
Changes since v1:
- Moved defines from drm.h to drm_mode.h
- Changed define prefix from DRM_ to DRM_MODE_PROP_
- Updated uses of the defines to the new prefix
- Removed include from drm_rect.c
- Stopped using the BIT() macro
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170519205017.23307-2-robert.foss@collabora.com
|
|
commit a667fb402c1e856209bf9e77ba41fc1cf356b867
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Thu Dec 15 15:29:44 2016 +0100
drm/i915: Disable all crtcs during driver unload, v2.
made sure that all crtc's are disabled on driver unload, but only the
following commit made sure all fb's are cleaned up correctly:
commit 9b2104f423de5c148749a07e8197dbab4c449877
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Tue Feb 21 14:51:40 2017 +0100
drm/atomic: Make disable_all helper fully disable the crtc.
Finally remove this and add a WARN_ON when vma is set. It should
have been removed by intel_cleanup_plane_fb().
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511082844.13965-2-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Streamline things by passing intel_plane and intel_crtc instead of
the drm types to our plane hooks.
v2: s/ilk/g4x/ in sprite code
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-3-ville.syrjala@linux.intel.com
|
|
Add tracepoints for plane programming. The tracepoints will dump
the frame and scanline counters, so this can be used to verify eg. that
the plane gets reprogrammed at the right time with respect to watermark
programming (if we have appropriate tracepoints for that as well).
v2: Rebase due to legacy cursor changes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-16-ville.syrjala@linux.intel.com
|
|
In a lot of place we wish to know which planes on the crtc are actually
visible, or how many of them there are. Let's start tracking that in a
bitmask in the crtc state.
We already track enabled planes (ie. ones with an fb and crtc specified by
the user) but that's not quite the same thing as enabled planes may
still end up being invisible due to clipping and whatnot.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-2-ville.syrjala@linux.intel.com
|
|
With atomic plane states we are able to track an allocation right from
preparation, during use and through to the final free after being
swapped out for a new plane. We can couple the VMA we pin for the
framebuffer (and its rotation) to this lifetime and avoid all the clumsy
lookups in between.
v2: Remove residual vma on plane cleanup (Chris)
v3: Add a description for the vma destruction in
intel_plane_destroy_state (Maarten)
References: https://bugs.freedesktop.org/show_bug.cgi?id=98829
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170116152131.18089-1-chris@chris-wilson.co.uk
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
Do something similar to vc4, only allow updating the cursor state
in-place through a fastpath when the watermarks are unaffected. This
will allow cursor movement to be smooth, but changing cursor size or
showing/hiding cursor will still fall back so watermarks can be updated.
Only moving and changing fb is allowed.
Changes since v1:
- Set page flip to always_unused for trybot.
- Copy fence correctly, ignore plane_state->state, should be NULL.
- Check crtc_state for !active and modeset, go to slowpath if the case.
Changes since v2:
- Make error handling work correctly. (Matthew Auld)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/a8e4cb00-5171-14e5-bbe3-dadb654ff296@linux.intel.com
|
|
Replace uses of fb->pixel_format with fb->format->format.
Less duplicated information is a good thing.
Note that coccinelle failed to eliminate the
"/* fourcc format */" comment from drm_framebuffer.h, so I had
to do that part manually.
@@
struct drm_framebuffer *FB;
expression E;
@@
drm_helper_mode_fill_fb_struct(...) {
...
- FB->pixel_format = E;
...
}
@@
struct drm_framebuffer *FB;
expression E;
@@
i9xx_get_initial_plane_config(...) {
...
- FB->pixel_format = E;
...
}
@@
struct drm_framebuffer *FB;
expression E;
@@
ironlake_get_initial_plane_config(...) {
...
- FB->pixel_format = E;
...
}
@@
struct drm_framebuffer *FB;
expression E;
@@
skylake_get_initial_plane_config(...) {
...
- FB->pixel_format = E;
...
}
@@
struct drm_framebuffer *a;
struct drm_framebuffer b;
@@
(
- a->pixel_format
+ a->format->format
|
- b.pixel_format
+ b.format->format
)
@@
struct drm_plane_state *a;
struct drm_plane_state b;
@@
(
- a->fb->pixel_format
+ a->fb->format->format
|
- b.fb->pixel_format
+ b.fb->format->format
)
@@
struct drm_crtc *CRTC;
@@
(
- CRTC->primary->fb->pixel_format
+ CRTC->primary->fb->format->format
|
- CRTC->primary->state->fb->pixel_format
+ CRTC->primary->state->fb->format->format
)
@@
struct drm_mode_set *set;
@@
(
- set->fb->pixel_format
+ set->fb->format->format
|
- set->crtc->primary->fb->pixel_format
+ set->crtc->primary->fb->format->format
)
@@
@@
struct drm_framebuffer {
...
- uint32_t pixel_format;
...
};
v2: Fix commit message (Laurent)
Rebase due to earlier removal of many fb->pixel_format uses,
including the 'fb->format = drm_format_info(fb->format->format);'
snafu
v3: Adjusted the semantic patch a bit and regenerated due to code
changes
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> (v1)
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1481751175-18463-1-git-send-email-ville.syrjala@linux.intel.com
|
|
Big thing is that drm-misc is now officially a group maintainer/committer
model thing, with MAINTAINERS suitably updated. Otherwise just the usual
pile of misc things all over, nothing that stands out this time around.
* tag 'drm-misc-next-2016-11-29' of git://anongit.freedesktop.org/git/drm-misc: (33 commits)
drm: Introduce drm_framebuffer_assign()
drm/bridge: adv7511: Enable the audio data and clock pads on adv7533
drm/bridge: adv7511: Add Audio support
drm/edid: Consider alternate cea timings to be the same VIC
drm/atomic: Constify drm_atomic_crtc_needs_modeset()
drm: bridge: dw-hdmi: add ASoC dependency
drm: Fix shift operations for drm_fb_helper::drm_target_preferred()
drm: Avoid NULL dereference for DRM_LEGACY debug message
drm: Use u64_to_user_ptr() helper for blob ioctls
drm: Fix conflicting macro parameter in drm_mm_for_each_node_in_range()
drm: Fixup kernel doc for driver->gem_create_object
drm/hisilicon/hibmc: mark PM functions __maybe_unused
drm/hisilicon/hibmc: Checking for NULL instead of IS_ERR()
drm: bridge: add DesignWare HDMI I2S audio support
drm: Check against color expansion in drm_mm_reserve_node()
drm: Define drm_mm_for_each_node_in_range()
drm/doc: Fix links in drm_property.c
MAINTAINERS: Add link to drm-misc documentation
vgaarb: use valid dev pointer in vgaarb_info()
drm/atomic: Unconfuse the old_state mess in commmit_tail
...
|
|
Tvrtko needs
commit b3c11ac267d461d3d597967164ff7278a919a39f
Author: Eric Engestrom <eric@engestrom.ch>
Date: Sat Nov 12 01:12:56 2016 +0000
drm: move allocation out of drm_get_format_name()
to be able to apply his patches without conflicts.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
It has been suggested that having per-plane modifiers is making life
more difficult for userspace, so let's just retire modifier[1-3] and
use modifier[0] to apply to the entire framebuffer.
Obviosuly this means that if individual planes need different tiling
layouts and whatnot we will need a new modifier for each combination
of planes with different tiling layouts.
For a bit of extra backwards compatilbilty the kernel will allow
non-zero modifier[1+] but it require that they will match modifier[0].
This in case there's existing userspace out there that sets
modifier[1+] to something non-zero with planar formats.
Mostly a cocci job, with a bit of manual stuff mixed in.
@@
struct drm_framebuffer *fb;
expression E;
@@
- fb->modifier[E]
+ fb->modifier
@@
struct drm_framebuffer fb;
expression E;
@@
- fb.modifier[E]
+ fb.modifier
Cc: Kristian Høgsberg <hoegsberg@gmail.com>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tomeu Vizoso <tomeu@tomeuvizoso.net>
Cc: dczaplejewicz@collabora.co.uk
Suggested-by: Kristian Høgsberg <hoegsberg@gmail.com>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Acked-by: Daniel Stone <daniels@collabora.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1479295996-26246-1-git-send-email-ville.syrjala@linux.intel.com
|
|
The primary and sprite planes on CHV pipe B support horizontal
mirroring. Expose it to the world.
Sadly the hardware ignores the mirror bit when the rotate bit is
set, so we'll have to reject the 180+X case.
v2: Drop the BIT()
v3: Pass dev_priv instead of dev to IS_CHERRYVIEW()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479142440-25283-4-git-send-email-ville.syrjala@linux.intel.com
|
|
The function's behaviour was changed in 90844f00049e, without changing
its signature, causing people to keep using it the old way without
realising they were now leaking memory.
Rob Clark also noticed it was also allocating GFP_KERNEL memory in
atomic contexts, breaking them.
Instead of having to allocate GFP_ATOMIC memory and fixing the callers
to make them cleanup the memory afterwards, let's change the function's
signature by having the caller take care of the memory and passing it to
the function.
The new parameter is a single-field struct in order to enforce the size
of its buffer and help callers to correctly manage their memory.
Fixes: 90844f00049e ("drm: make drm_get_format_name thread-safe")
Cc: Rob Clark <robdclark@gmail.com>
Cc: Christian König <christian.koenig@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Acked-by: Sinclair Yeh <syeh@vmware.com> (vmwgfx)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Eric Engestrom <eric@engestrom.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161112011309.9799-1-eric@engestrom.ch
|
|
In preparation to support many distinct timelines, we need to expand the
activity tracking on the GEM object to handle more than just a request
per engine. We already use the struct reservation_object on the dma-buf
to handle many fence contexts, so integrating that into the GEM object
itself is the preferred solution. (For example, we can now share the same
reservation_object between every consumer/producer using this buffer and
skip the manual import/export via dma-buf.)
v2: Reimplement busy-ioctl (by walking the reservation object), postpone
the ABI change for another day. Similarly use the reservation object to
find the last_write request (if active and from i915) for choosing
display CS flips.
Caveats:
* busy-ioctl: busy-ioctl only reports on the native fences, it will not
warn of stalls (in set-domain-ioctl, pread/pwrite etc) if the object is
being rendered to by external fences. It also will not report the same
busy state as wait-ioctl (or polling on the dma-buf) in the same
circumstances. On the plus side, it does retain reporting of which
*i915* engines are engaged with this object.
* non-blocking atomic modesets take a step backwards as the wait for
render completion blocks the ioctl. This is fixed in a subsequent
patch to use a fence instead for awaiting on the rendering, see
"drm/i915: Restore nonblocking awaits for modesetting"
* dynamic array manipulation for shared-fences in reservation is slower
than the previous lockless static assignment (e.g. gem_exec_lut_handle
runtime on ivb goes from 42s to 66s), mainly due to atomic operations
(maintaining the fence refcounts).
* loss of object-level retirement callbacks, emulated by VMA retirement
tracking.
* minor loss of object-level last activity information from debugfs,
could be replaced with per-vma information if desired
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161028125858.23563-21-chris@chris-wilson.co.uk
|
|
We have intel_rotation_90_or_270() in i915 to check if the rotation is
90 or 270 degrees. Similar checks are elsewhere in drm, so let's move
the helper into a central place and use it everwhere.
v2: Drop the BIT()
Convert all new intel_rotation_90_or_270() calls
Deal with superfluous code shuffling
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1474907460-10717-2-git-send-email-ville.syrjala@linux.intel.com
|
|
Signed-off-by: Eric Engestrom <eric.engestrom@imgtec.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Signed-off-by: Eric Engestrom <eric@engestrom.ch>
[danvet: Clarify that the returned pointer must be freed with
kfree().]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Replace the use of drm_plane_helper_check_update() with
drm_plane_helper_check_state() since we have a plane state.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1469549224-1860-6-git-send-email-ville.syrjala@linux.intel.com
|
|
Replace the private drm_rects/flags in intel_plane_state
with the ones now living in drm_plane_state.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1469549224-1860-5-git-send-email-ville.syrjala@linux.intel.com
|
|
Only property creation uses the rotation as an index, so convert the
to figure the index when needed.
v2: Use the new defines to build the _MASK defines (Sean)
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: malidp@foss.arm.com
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Cc: Sean Paul <seanpaul@chromium.org>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1469771405-17653-1-git-send-email-joonas.lahtinen@linux.intel.com
|
|
Pass the current crtc state, not the old crtc state, to the
.update_plane() hook.
Noticed on BSW when PRIMSIZE was getting programmed to a stale value
which produced utter garbage on screen eg. wwhen going from 1920x1080
to 1024x768.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: a758e6845825 ("drm/i915: Do not use commit_plane for sprite planes.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457543247-13987-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
|
|
With sprites, cursors and primary planes taking the atomic state
this is now unused. It's removed in a separate commit to allow
a revert.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452164052-21752-8-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
|
|
Use update_plane and disable_plane directly.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452164052-21752-3-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
|
|
When the crtc is configured but not active we currently clip to (0,0)x(0,0).
This results in differences in calculations depending on dpms setting.
When the crtc is enabled but not active run check_plane as if it were on,
but afterwards set plane_state->visible = false for the checks.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447945645-32005-13-git-send-email-maarten.lankhorst@linux.intel.com
|
|
Make pinning and waiting a separate step, and wait for object idle
without struct_mutex held.
Changes since v1:
- Do not wait when a reset is in progress.
- Remove call to i915_gem_object_wait_rendering for
intel_overlay_do_put_image (Chris Wilson)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
|
Ville Syrjälä
Maarten Lankhorst
Dave Airlie
Gustavo Padovan
Chris Wilson
Mahesh Kumar
Robert Foss
Daniel Vetter
Eric Engestrom
Eric Engestrom
Joonas Lahtinen