| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
According to the eLCDIF initialization steps listed in the MX6SX
Reference Manual the eLCDIF block reset is mandatory.
Without performing the eLCDIF reset the display shows garbage content
when the kernel boots.
In earlier tests this issue has not been observed because the bootloader
was previously showing a splash screen and the bootloader display driver
does properly implement the eLCDIF reset.
Add the eLCDIF reset to the driver, so that it can operate correctly
independently of the bootloader.
Tested on a imx6sx-sdb board.
Cc: <stable@vger.kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1494007301-14535-1-git-send-email-fabio.estevam@nxp.com
|
|
Currently the framebuffer content is displayed with incorrect offsets
in both the vertical and horizontal directions.
The fbdev version of the driver does not show this problem. Breno Lima
dumped the eLCDIF controller registers on both the drm and fbdev drivers
and noticed that the VDCTRL3 register is configured incorrectly in the
drm driver.
The fbdev driver calculates the vertical and horizontal wait counts
of the VDCTRL3 register by doing: back porch + sync length.
Looking at the horizontal and vertical timing diagram from
include/drm/drm_modes.h this value corresponds to:
crtc_[hv]total - crtc_[hv]sync_start
So fix the VDCTRL3 register setting accordingly so that the eLCDIF
controller can properly show the framebuffer content in the correct
position.
Reported-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The DRM subsystem specifies the pixel clock polarity from a
controllers perspective: DRM_BUS_FLAG_PIXDATA_NEGEDGE means
the controller drives the data on pixel clocks falling edge.
That is the controllers DOTCLK_POL=0 (Default is data launched
at negative edge).
Also change the data enable logic to be high active by default
and only change if explicitly requested via bus_flags. With
that defaults are:
- Data enable: high active
- Pixel clock polarity: controller drives data on negative edge
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The LCD bus width does not need to align with the pixel format. The
LCDIF controller automatically converts between pixel formats and
bus width by padding or dropping LSBs.
The DRM subsystem has the notion of bus_format which allows to
determine what bus_formats are supported by the display. Choose the
first available or fallback to 24 bit if none are available.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Replace uses of fb->pixel_format with fb->format->format.
Less duplicated information is a good thing.
Note that coccinelle failed to eliminate the
"/* fourcc format */" comment from drm_framebuffer.h, so I had
to do that part manually.
@@
struct drm_framebuffer *FB;
expression E;
@@
drm_helper_mode_fill_fb_struct(...) {
...
- FB->pixel_format = E;
...
}
@@
struct drm_framebuffer *FB;
expression E;
@@
i9xx_get_initial_plane_config(...) {
...
- FB->pixel_format = E;
...
}
@@
struct drm_framebuffer *FB;
expression E;
@@
ironlake_get_initial_plane_config(...) {
...
- FB->pixel_format = E;
...
}
@@
struct drm_framebuffer *FB;
expression E;
@@
skylake_get_initial_plane_config(...) {
...
- FB->pixel_format = E;
...
}
@@
struct drm_framebuffer *a;
struct drm_framebuffer b;
@@
(
- a->pixel_format
+ a->format->format
|
- b.pixel_format
+ b.format->format
)
@@
struct drm_plane_state *a;
struct drm_plane_state b;
@@
(
- a->fb->pixel_format
+ a->fb->format->format
|
- b.fb->pixel_format
+ b.fb->format->format
)
@@
struct drm_crtc *CRTC;
@@
(
- CRTC->primary->fb->pixel_format
+ CRTC->primary->fb->format->format
|
- CRTC->primary->state->fb->pixel_format
+ CRTC->primary->state->fb->format->format
)
@@
struct drm_mode_set *set;
@@
(
- set->fb->pixel_format
+ set->fb->format->format
|
- set->crtc->primary->fb->pixel_format
+ set->crtc->primary->fb->format->format
)
@@
@@
struct drm_framebuffer {
...
- uint32_t pixel_format;
...
};
v2: Fix commit message (Laurent)
Rebase due to earlier removal of many fb->pixel_format uses,
including the 'fb->format = drm_format_info(fb->format->format);'
snafu
v3: Adjusted the semantic patch a bit and regenerated due to code
changes
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> (v1)
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1481751175-18463-1-git-send-email-ville.syrjala@linux.intel.com
|
|
Add new driver for the MXSFB controller found in i.MX23/28/6SX .
The MXSFB controller is a simple framebuffer controller with one
parallel LCD output. Unlike the MXSFB fbdev driver that is used
on these systems now, this driver uses the DRM/KMS framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
|
Fabio Estevam
Stefan Agner
Ville Syrjälä
Marek Vasut