| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The probe routine acquires the reset GPIO using GPIOD_OUT_LOW. Directly
afterwards it calls acx565akm_detect(), which sets the GPIO value to
HIGH. If the bootloader initialized the GPIO to HIGH before the probe
routine was called, there is only a very short time period of a few
instructions where the reset signal is LOW. Exact time depends on
compiler optimizations, kernel configuration and alignment of the stars,
but I expect it to be always way less than 10us. There are no public
datasheets for the panel, but acx565akm_power_on() has a comment with
timings and reset period should be at least 10us. So this potentially
brings the panel into a half-reset state.
The result is, that panel may not work after boot and can get into a
working state by re-enabling it (e.g. by blanking + unblanking), since
that does a clean reset cycle. This bug has recently been hit by Ivaylo
Dimitrov, but there are some older reports which are probably the same
bug. At least Tony Lindgren, Peter Ujfalusi and Jarkko Nikula have
experienced it in 2017 describing the blank/unblank procedure as
possible workaround.
Note, that the bug really goes back in time. It has originally been
introduced in the predecessor of the omapfb driver in commit 3c45d05be382
("OMAPDSS: acx565akm panel: handle gpios in panel driver") in 2012.
That driver eventually got replaced by a newer one, which had the bug
from the beginning in commit 84192742d9c2 ("OMAPDSS: Add Sony ACX565AKM
panel driver") and still exists in fbdev world. That driver has later
been copied to omapdrm and then was used as a basis for this driver.
Last but not least the omapdrm specific driver has been removed in
commit 45f16c82db7e ("drm/omap: displays: Remove unused panel drivers").
Reported-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fixes: 1c8fc3f0c5d2 ("drm/panel: Add driver for the Sony ACX565AKM panel")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201127200429.129868-1-sebastian.reichel@collabora.com
|
|
The function "int drm_panel_add(struct drm_panel *panel)"
always returns 0, this return value is meaningless.
Also, there is no need to check return value which calls
"drm_panel_add and", error branch code will never run.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200801120216.8488-1-bernard@vivo.com
|
|
Get rid of mode->vrefresh and just calculate it on demand. Saves
a bit of space and avoids the cached value getting out of sync
with reality.
Mostly done with cocci, with the following manual fixups:
- Remove the now empty loop in drm_helper_probe_single_connector_modes()
- Fix __MODE() macro in ch7006_mode.c
- Fix DRM_MODE_ARG() macro in drm_modes.h
- Remove leftover comment from samsung_s6d16d0_mode
- Drop the TODO
@@
@@
struct drm_display_mode {
...
- int vrefresh;
...
};
@@
identifier N;
expression E;
@@
struct drm_display_mode N = {
- .vrefresh = E
};
@@
identifier N;
expression E;
@@
struct drm_display_mode N[...] = {
...,
{
- .vrefresh = E
}
,...
};
@@
expression E;
@@
{
DRM_MODE(...),
- .vrefresh = E,
}
@@
identifier M, R;
@@
int drm_mode_vrefresh(const struct drm_display_mode *M)
{
...
- if (M->vrefresh > 0)
- R = M->vrefresh;
- else
if (...) {
...
}
...
}
@@
struct drm_display_mode *p;
expression E;
@@
(
- p->vrefresh = E;
|
- p->vrefresh
+ drm_mode_vrefresh(p)
)
@@
struct drm_display_mode s;
expression E;
@@
(
- s.vrefresh = E;
|
- s.vrefresh
+ drm_mode_vrefresh(&s)
)
@@
expression E;
@@
- drm_mode_vrefresh(E) ? drm_mode_vrefresh(E) : drm_mode_vrefresh(E)
+ drm_mode_vrefresh(E)
@find_substruct@
identifier X;
identifier S;
@@
struct X {
...
struct drm_display_mode S;
...
};
@@
identifier find_substruct.S;
expression E;
identifier I;
@@
{
.S = {
- .vrefresh = E
}
}
@@
identifier find_substruct.S;
identifier find_substruct.X;
expression E;
identifier I;
@@
struct X I[...] = {
...,
.S = {
- .vrefresh = E
}
,...
};
v2: Drop TODO
v3: Rebase
v4: Rebase
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jerry Han <hanxu5@huaqin.corp-partner.google.com>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Stefan Mavrodiev <stefan@olimex.com>
Cc: Robert Chiras <robert.chiras@nxp.com>
Cc: "Guido Günther" <agx@sigxcpu.org>
Cc: Purism Kernel Team <kernel@puri.sm>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: VMware Graphics <linux-graphics-maintainer@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: linux-amlogic@lists.infradead.org
Cc: nouveau@lists.freedesktop.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200428171940.19552-4-ville.syrjala@linux.intel.com
|
|
The panel drivers used drm_panel.drm for two purposes:
1) Argument to drm_mode_duplicate()
2) drm->dev was used in error messages
The first usage is replaced with drm_connector.dev
- drm_connector is already connected to a drm_device
and we have a valid connector
The second usage is replaced with drm_panel.dev
- this makes drivers more consistent in their dev argument
used for dev_err() and friends
With these replacements there are no more uses of drm_panel.drm,
so it is removed from struct drm_panel.
With this change drm_panel_attach() and drm_panel_detach()
no longer have any use as they are empty functions.
v2:
- editorial correction in changelog (Laurent)
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Stefan Mavrodiev <stefan@olimex.com>
Cc: Robert Chiras <robert.chiras@nxp.com>
Cc: "Guido Günther" <agx@sigxcpu.org>
Cc: Purism Kernel Team <kernel@puri.sm>
Link: https://patchwork.freedesktop.org/patch/msgid/20191207140353.23967-8-sam@ravnborg.org
|
|
Today the bridge creates the drm_connector, but that is planned
to be moved to the display drivers.
To facilitate this, update drm_panel_funcs.get_modes() to
take drm_connector as an argument.
All panel drivers implementing get_modes() are updated.
v2:
- drop accidental change (Laurent)
- update docs for get_modes (Laurent)
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Stefan Mavrodiev <stefan@olimex.com>
Cc: Robert Chiras <robert.chiras@nxp.com>
Cc: "Guido Günther" <agx@sigxcpu.org>
Cc: Purism Kernel Team <kernel@puri.sm>
Link: https://patchwork.freedesktop.org/patch/msgid/20191207140353.23967-6-sam@ravnborg.org
|
|
Thierry needs fd70c7755bf0 ("drm/bridge: tc358767: fix max_tu_symbol
value") to be able to merge his dp_link patch series.
Some adjacent changes conflicts, plus some clashes in i915 due to
cherry-picking and git trying to be helpful and leaving both versions
in.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The panel-sony-acx565akm driver incorrectly includes the OF vendor
prefix in its SPI alias. Fix it, and move the manual alias to an SPI
module device table.
Fixes: 1c8fc3f0c5d2 ("drm/panel: Add driver for the Sony ACX565AKM panel")
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191007170801.27647-4-laurent.pinchart@ideasonboard.com
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add a type field to the drm_panel structure to report the panel type,
using DRM_MODE_CONNECTOR_* macros (the values that make sense are LVDS,
eDP, DSI and DPI). This will be used to initialise the corresponding
connector type.
Update all panel drivers accordingly. The panel-simple driver only
specifies the type for the known to be LVDS panels, while all other
panels are left as unknown and will be converted on a case-by-case
basis as they all need to be carefully reviewed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190904132804.29680-2-laurent.pinchart@ideasonboard.com
|
|
Instead of requiring all drivers to set the dev and funcs fields of
drm_panel manually after calling drm_panel_init(), pass the data as
arguments to the function. This simplifies the panel drivers, and will
help future refactoring when adding new arguments to drm_panel_init().
The panel drivers have been updated with the following Coccinelle
semantic patch, with manual inspection to verify that no call to
drm_panel_init() with a single argument still exists.
@@
expression panel;
expression device;
identifier ops;
@@
drm_panel_init(&panel
+ , device, &ops
);
...
(
-panel.dev = device;
-panel.funcs = &ops;
|
-panel.funcs = &ops;
-panel.dev = device;
)
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823193245.23876-3-laurent.pinchart@ideasonboard.com
|
|
This panel is used on the OpenMoko Neo FreeRunner and Neo 1973.
The code is based on the omapdrm-specific panel-tpo-td028ttec1 driver.
v2:
- fix checkpatch warnings:
o (lcd == NULL) => (!lcd) (sam)
o (1 << X) => BIT(X) (sam)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190813201101.30980-9-laurent.pinchart@ideasonboard.com
|
|
This panel is used on the Nokia N900.
The code is based on the omapdrm-specific panel-sony-acx565akm driver.
The hardware-related logic has been changed as little as possible to
avoid regressions as hardware availability is lacking to test the
changes. Follow-up patches should address the items listed in the TODO
list.
v2:
- fix checkpatch warning (lcd == NULL) => (!lcd) (sam)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190813201101.30980-8-laurent.pinchart@ideasonboard.com
|
Sebastian Reichel
Bernard Zhao
Ville Syrjälä
Sam Ravnborg
Daniel Vetter
Laurent Pinchart