aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/gpu/drm/stm (follow)
AgeCommit message (Collapse)AuthorFilesLines
2021-09-09drm/stm: ltdc: add layer alpha supportRaphael Gallais-Pou1-1/+3
Android Hardware Composer supports alpha values applied to layers. Enabling non-opaque layers for the STM CRTC could help offload GPU resources for screen composition. Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com> Acked-by: Yannick Fertre <yannick.fertre@foss.st.com> Reviewed-by: Yannick Fertre <yannick.fertre@foss.st.com> Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210907151534.6013-1-raphael.gallais-pou@foss.st.com
2021-09-09drm/stm: ltdc: attach immutable zpos property to planesRaphael Gallais-Pou1-0/+3
Defines plane ordering by hard-coding an immutable Z position from the first plane, used as primary layer, to the next ones as overlay in order of instantiation. This zpos is only an information as it is not possible to modify it, blending operations are still applied from the top to the bottom layer. This patch helps to remove a warning message from the Android Hardware Composer. Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com> Acked-by: Yannick Fertre <yannick.fertre@foss.st.com> Reviewed-by: Yannick Fertre <yannick.fertre@foss.st.com> Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210907151323.5850-1-raphael.gallais-pou@foss.st.com
2021-07-19drm/stm: dsi: compute the transition time from LP to HS and backAntonio Borneo1-4/+13
The driver uses a conservative set of hardcoded values for the maximum time delay of the transitions between LP and HS, either for data and clock lanes. By using the info in STM32MP157 datasheet, valid also for other ST devices, compute the actual delay from the lane's bps. Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com> Reviewed-by: Philippe Cornu <philippe.cornu@foss.st.com> Acked-by: Philippe Cornu <philippe.cornu@foss.st.com> Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210713144941.3599-1-antonio.borneo@foss.st.com
2021-07-19drm/stm: ltdc: Silence -EPROBE_DEFER till bridge attachedJagan Teki1-3/+5
As dw-mipi-dsi supported all possible ways to find the DSI devices. It can take multiple iterations for ltdc to find all components attached to the DSI bridge. The current ltdc driver failed to find the endpoint as it returned -EINVAL for the first iteration itself. This leads to following error: [    3.099289] [drm:ltdc_load] *ERROR* init encoder endpoint 0 So, check the return value and cleanup the encoder only if it's not -EPROBE_DEFER. This make all components in the attached DSI bridge found properly. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Yannick Fertre <yannick.fertre@foss.st.com> Acked-by: Philippe Cornu <philippe.cornu@foss.st.com> Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210704135914.268308-1-jagan@amarulasolutions.com
2021-06-29drm/stm: Don't set struct drm_device.irq_enabledThomas Zimmermann1-3/+0
The field drm_device.irq_enabled is only used by legacy drivers with userspace modesetting. Don't set it in stm. Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Tested-by: Yannick Fertre <yannick.fertre@foss.st.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210625082222.3845-20-tzimmermann@suse.de
2021-06-24drm/<driver>: drm_gem_plane_helper_prepare_fb is now the defaultDaniel Vetter1-1/+0
No need to set it explicitly. Acked-by: Philipp Zabel <p.zabel@pengutronix.de> Acked-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Paul Cercueil <paul@crapouillou.net> Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Acked-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Acked-by: Philippe Cornu <philippe.cornu@foss.st.com> Acked-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Cc: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: Philipp Zabel <p.zabel@pengutronix.de> Cc: Paul Cercueil <paul@crapouillou.net> Cc: Chun-Kuang Hu <chunkuang.hu@kernel.org> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Jerome Brunet <jbrunet@baylibre.com> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: Marek Vasut <marex@denx.de> Cc: Stefan Agner <stefan@agner.ch> Cc: Sandy Huang <hjc@rock-chips.com> Cc: "Heiko Stübner" <heiko@sntech.de> Cc: Yannick Fertre <yannick.fertre@foss.st.com> Cc: Philippe Cornu <philippe.cornu@foss.st.com> Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: Chen-Yu Tsai <wens@csie.org> Cc: Jernej Skrabec <jernej.skrabec@gmail.com> Cc: Jyri Sarha <jyri.sarha@iki.fi> Cc: Tomi Valkeinen <tomba@kernel.org> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-mips@vger.kernel.org Cc: linux-mediatek@lists.infradead.org Cc: linux-amlogic@lists.infradead.org Cc: linux-rockchip@lists.infradead.org Cc: linux-stm32@st-md-mailman.stormreply.com Cc: linux-sunxi@lists.linux.dev Link: https://patchwork.freedesktop.org/patch/msgid/20210622165511.3169559-9-daniel.vetter@ffwll.ch
2021-06-08drm/stm: Remove usage of drm_display_mode_to_videomode()Marek Vasut1-16/+17
There is not much value in the extra conversion step, the calculations required for the LTDC IP are different than what is used in the drm_display_mode_to_videomode(), so just do the right ones in the LTDC driver right away. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Antonio Borneo <antonio.borneo@foss.st.com> Cc: Benjamin Gaignard <benjamin.gaignard@foss.st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Philippe Cornu <philippe.cornu@foss.st.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Vincent Abriou <vincent.abriou@foss.st.com> Cc: Yannick Fertre <yannick.fertre@foss.st.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-stm32@st-md-mailman.stormreply.com To: dri-devel@lists.freedesktop.org Tested-by: Yannick Fertré <yannick.fertre@st.com> Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210607172457.14471-1-marex@denx.de
2021-05-06drm/stm: Don't set allow_fb_modifiers explicitlyDaniel Vetter1-2/+0
Since commit 890880ddfdbe256083170866e49c87618b706ac7 Author: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Date: Fri Jan 4 09:56:10 2019 +0100 drm: Auto-set allow_fb_modifiers when given modifiers at plane init this is done automatically as part of plane init, if drivers set the modifier list correctly. Which is the case here. Acked-by: Philippe Cornu <philippe.cornu@st.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Cc: Yannick Fertre <yannick.fertre@foss.st.com> Cc: Philippe Cornu <philippe.cornu@foss.st.com> Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: linux-stm32@st-md-mailman.stormreply.com Cc: linux-arm-kernel@lists.infradead.org Link: https://patchwork.freedesktop.org/patch/msgid/20210427092018.832258-7-daniel.vetter@ffwll.ch
2021-03-08drm/stm: dsi: Avoid printing errors for -EPROBE_DEFERYannick Fertre1-6/+3
Don't print error when probe deferred error is returned. Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com> Signed-off-by: Yannick Fertre <yannick.fertre@foss.st.com> Tested-by: Yannick Fertre <yannick.fertre@foss.st.com> Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210222092205.32086-2-raphael.gallais-pou@foss.st.com
2021-03-08drm/stm: ltdc: Use simple encoderJagan Teki1-10/+2
STM ltdc driver uses an empty implementation for its encoder. Replace the code with the generic simple encoder. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Tested-by: Yannick Fertre <yannick.fertre@foss.st.com> Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210302175700.28640-1-jagan@amarulasolutions.com
2021-02-25drm: Use state helper instead of the plane state pointerMaxime Ripard1-1/+2
Many drivers reference the plane->state pointer in order to get the current plane state in their atomic_update or atomic_disable hooks, which would be the new plane state in the global atomic state since _swap_state happened when those hooks are run. Use the drm_atomic_get_new_plane_state helper to get that state to make it more obvious. This was made using the coccinelle script below: @ plane_atomic_func @ identifier helpers; identifier func; @@ ( static const struct drm_plane_helper_funcs helpers = { ..., .atomic_disable = func, ..., }; | static const struct drm_plane_helper_funcs helpers = { ..., .atomic_update = func, ..., }; ) @ adds_new_state @ identifier plane_atomic_func.func; identifier plane, state; identifier new_state; @@ func(struct drm_plane *plane, struct drm_atomic_state *state) { ... - struct drm_plane_state *new_state = plane->state; + struct drm_plane_state *new_state = drm_atomic_get_new_plane_state(state, plane); ... } @ include depends on adds_new_state @ @@ #include <drm/drm_atomic.h> @ no_include depends on !include && adds_new_state @ @@ + #include <drm/drm_atomic.h> #include <drm/...> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://lore.kernel.org/r/20210219120032.260676-1-maxime@cerno.tech
2021-02-25drm/atomic: Pass the full state to planes atomic disable and updateMaxime Ripard1-2/+4
The current atomic helpers have either their object state being passed as an argument or the full atomic state. The former is the pattern that was done at first, before switching to the latter for new hooks or when it was needed. Let's convert the remaining helpers to provide a consistent interface, this time with the planes atomic_update and atomic_disable. The conversion was done using the coccinelle script below, built tested on all the drivers. @@ identifier plane, plane_state; symbol state; @@ struct drm_plane_helper_funcs { ... void (*atomic_update)(struct drm_plane *plane, - struct drm_plane_state *plane_state); + struct drm_atomic_state *state); ... } @@ identifier plane, plane_state; symbol state; @@ struct drm_plane_helper_funcs { ... void (*atomic_disable)(struct drm_plane *plane, - struct drm_plane_state *plane_state); + struct drm_atomic_state *state); ... } @ plane_atomic_func @ identifier helpers; identifier func; @@ ( static const struct drm_plane_helper_funcs helpers = { ..., .atomic_update = func, ..., }; | static const struct drm_plane_helper_funcs helpers = { ..., .atomic_disable = func, ..., }; ) @@ struct drm_plane_helper_funcs *FUNCS; identifier f; identifier crtc_state; identifier plane, plane_state, state; expression e; @@ f(struct drm_crtc_state *crtc_state) { ... struct drm_atomic_state *state = e; <+... ( - FUNCS->atomic_disable(plane, plane_state) + FUNCS->atomic_disable(plane, state) | - FUNCS->atomic_update(plane, plane_state) + FUNCS->atomic_update(plane, state) ) ...+> } @@ identifier plane_atomic_func.func; identifier plane; symbol state; @@ func(struct drm_plane *plane, - struct drm_plane_state *state) + struct drm_plane_state *old_plane_state) { <... - state + old_plane_state ...> } @ ignores_old_state @ identifier plane_atomic_func.func; identifier plane, old_state; @@ func(struct drm_plane *plane, struct drm_plane_state *old_state) { ... when != old_state } @ adds_old_state depends on plane_atomic_func && !ignores_old_state @ identifier plane_atomic_func.func; identifier plane, plane_state; @@ func(struct drm_plane *plane, struct drm_plane_state *plane_state) { + struct drm_plane_state *plane_state = drm_atomic_get_old_plane_state(state, plane); ... } @ depends on plane_atomic_func @ identifier plane_atomic_func.func; identifier plane, plane_state; @@ func(struct drm_plane *plane, - struct drm_plane_state *plane_state + struct drm_atomic_state *state ) { ... } @ include depends on adds_old_state @ @@ #include <drm/drm_atomic.h> @ no_include depends on !include && adds_old_state @ @@ + #include <drm/drm_atomic.h> #include <drm/...> @@ identifier plane_atomic_func.func; identifier plane, state; identifier plane_state; @@ func(struct drm_plane *plane, struct drm_atomic_state *state) { ... struct drm_plane_state *plane_state = drm_atomic_get_old_plane_state(state, plane); <+... - plane_state->state + state ...+> } Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20210219120032.260676-9-maxime@cerno.tech
2021-02-24drm: Rename plane->state variables in atomic update and disableMaxime Ripard1-14/+14
Some drivers are storing the plane->state pointer in atomic_update and atomic_disable in a variable simply called state, while the state passed as an argument is called old_state. In order to ease subsequent reworks and to avoid confusing or inconsistent names, let's rename those variables to new_state. This was done using the following coccinelle script, plus some manual changes for mtk and tegra. @ plane_atomic_func @ identifier helpers; identifier func; @@ ( static const struct drm_plane_helper_funcs helpers = { ..., .atomic_disable = func, ..., }; | static const struct drm_plane_helper_funcs helpers = { ..., .atomic_update = func, ..., }; ) @ moves_new_state_old_state @ identifier plane_atomic_func.func; identifier plane; symbol old_state; symbol state; @@ func(struct drm_plane *plane, struct drm_plane_state *old_state) { ... - struct drm_plane_state *state = plane->state; + struct drm_plane_state *new_state = plane->state; ... } @ depends on moves_new_state_old_state @ identifier plane_atomic_func.func; identifier plane; identifier old_state; symbol state; @@ func(struct drm_plane *plane, struct drm_plane_state *old_state) { <... - state + new_state ...> } @ moves_new_state_oldstate @ identifier plane_atomic_func.func; identifier plane; symbol oldstate; symbol state; @@ func(struct drm_plane *plane, struct drm_plane_state *oldstate) { ... - struct drm_plane_state *state = plane->state; + struct drm_plane_state *newstate = plane->state; ... } @ depends on moves_new_state_oldstate @ identifier plane_atomic_func.func; identifier plane; identifier old_state; symbol state; @@ func(struct drm_plane *plane, struct drm_plane_state *old_state) { <... - state + newstate ...> } @ moves_new_state_old_pstate @ identifier plane_atomic_func.func; identifier plane; symbol old_pstate; symbol state; @@ func(struct drm_plane *plane, struct drm_plane_state *old_pstate) { ... - struct drm_plane_state *state = plane->state; + struct drm_plane_state *new_pstate = plane->state; ... } @ depends on moves_new_state_old_pstate @ identifier plane_atomic_func.func; identifier plane; identifier old_pstate; symbol state; @@ func(struct drm_plane *plane, struct drm_plane_state *old_pstate) { <... - state + new_pstate ...> } Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20210219120032.260676-8-maxime@cerno.tech
2021-02-24drm/atomic: Pass the full state to planes atomic_checkMaxime Ripard1-1/+3
The current atomic helpers have either their object state being passed as an argument or the full atomic state. The former is the pattern that was done at first, before switching to the latter for new hooks or when it was needed. Let's convert all the remaining helpers to provide a consistent interface, starting with the planes atomic_check. The conversion was done using the coccinelle script below plus some manual changes for vmwgfx, built tested on all the drivers. @@ identifier plane, plane_state; symbol state; @@ struct drm_plane_helper_funcs { ... int (*atomic_check)(struct drm_plane *plane, - struct drm_plane_state *plane_state); + struct drm_atomic_state *state); ... } @ plane_atomic_func @ identifier helpers; identifier func; @@ static const struct drm_plane_helper_funcs helpers = { ..., .atomic_check = func, ..., }; @@ struct drm_plane_helper_funcs *FUNCS; identifier f; identifier dev; identifier plane, plane_state, state; @@ f(struct drm_device *dev, struct drm_atomic_state *state) { <+... - FUNCS->atomic_check(plane, plane_state) + FUNCS->atomic_check(plane, state) ...+> } @ ignores_new_state @ identifier plane_atomic_func.func; identifier plane, new_plane_state; @@ func(struct drm_plane *plane, struct drm_plane_state *new_plane_state) { ... when != new_plane_state } @ adds_new_state depends on plane_atomic_func && !ignores_new_state @ identifier plane_atomic_func.func; identifier plane, new_plane_state; @@ func(struct drm_plane *plane, struct drm_plane_state *new_plane_state) { + struct drm_plane_state *new_plane_state = drm_atomic_get_new_plane_state(state, plane); ... } @ depends on plane_atomic_func @ identifier plane_atomic_func.func; identifier plane, new_plane_state; @@ func(struct drm_plane *plane, - struct drm_plane_state *new_plane_state + struct drm_atomic_state *state ) { ... } @ include depends on adds_new_state @ @@ #include <drm/drm_atomic.h> @ no_include depends on !include && adds_new_state @ @@ + #include <drm/drm_atomic.h> #include <drm/...> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20210219120032.260676-4-maxime@cerno.tech
2021-02-24drm: Rename plane atomic_check state namesMaxime Ripard1-5/+5
Most drivers call the argument to the plane atomic_check hook simply state, which is going to conflict with the global atomic state in a later rework. Let's rename it to new_plane_state (or new_state depending on the convention used in the driver). This was done using the coccinelle script below, and built tested: @ plane_atomic_func @ identifier helpers; identifier func; @@ static const struct drm_plane_helper_funcs helpers = { .atomic_check = func, }; @ has_old_state @ identifier plane_atomic_func.func; identifier plane; expression e; symbol old_state; symbol state; @@ func(struct drm_plane *plane, struct drm_plane_state *state) { ... struct drm_plane_state *old_state = e; ... } @ depends on has_old_state @ identifier plane_atomic_func.func; identifier plane; symbol old_state; @@ func(struct drm_plane *plane, - struct drm_plane_state *state + struct drm_plane_state *new_state ) { <+... - state + new_state ...+> } @ has_state @ identifier plane_atomic_func.func; identifier plane; symbol state; @@ func(struct drm_plane *plane, struct drm_plane_state *state) { ... } @ depends on has_state @ identifier plane_atomic_func.func; identifier plane; symbol old_state; @@ func(struct drm_plane *plane, - struct drm_plane_state *state + struct drm_plane_state *new_plane_state ) { <+... - state + new_plane_state ...+> } Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20210219120032.260676-2-maxime@cerno.tech
2021-02-23drm/gem: Move drm_gem_fb_prepare_fb() to GEM atomic helpersThomas Zimmermann1-2/+2
The function drm_gem_fb_prepare_fb() is a helper for atomic modesetting, but currently located next to framebuffer helpers. Move it to GEM atomic helpers, rename it slightly and adopt the drivers. Same for the rsp simple-pipe helper. Compile-tested with x86-64, aarch64 and arm. The patch is fairly large, but there are no functional changes. v3: * remove out-comented line in drm_gem_framebuffer_helper.h (Maxime) v2: * rename to drm_gem_plane_helper_prepare_fb() (Daniel) * add tutorial-style documentation Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Acked-by: Maxime Ripard <mripard@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20210222141756.7864-1-tzimmermann@suse.de
2021-02-15drm/stm: Fix bus_flags handlingMarek Vasut1-2/+31
The drm_display_mode_to_videomode() does not populate DISPLAY_FLAGS_DE_LOW or DISPLAY_FLAGS_PIXDATA_NEGEDGE flags in struct videomode. Therefore, no matter what polarity the next bridge or display might require, these flags are never set, and thus the LTDC GCR_DEPOL and GCR_PCPOL bits are never set and the LTDC behaves as if both DISPLAY_FLAGS_PIXDATA_POSEDGE and DISPLAY_FLAGS_DE_HIGH were always set. The fix for this problem is taken almost verbatim from MXSFB driver. In case there is a bridge attached to the LTDC, the bridge might have extra polarity requirements, so extract bus_flags from the bridge and use them for LTDC configuration. Otherwise, extract bus_flags from the connector, which is the display. Fixes: b759012c5fa7 ("drm/stm: Add STM32 LTDC driver") Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Yannick Fertre <yannick.fertre@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Antonio Borneo <antonio.borneo@st.com> Cc: Benjamin Gaignard <benjamin.gaignard@st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Philippe Cornu <philippe.cornu@st.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Vincent Abriou <vincent.abriou@st.com> Cc: Yannick Fertre <yannick.fertre@st.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-stm32@st-md-mailman.stormreply.com To: dri-devel@lists.freedesktop.org Tested-by: Yannick Fertre <yannick.fertre@foss.st.com> Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210127110756.125570-1-marex@denx.de
2020-12-15drm: automatic legacy gamma supportTomi Valkeinen1-1/+0
To support legacy gamma ioctls the drivers need to set drm_crtc_funcs.gamma_set either to a custom implementation or to drm_atomic_helper_legacy_gamma_set. Most of the atomic drivers do the latter. We can simplify this by making the core handle it automatically. Move the drm_atomic_helper_legacy_gamma_set() functionality into drm_color_mgmt.c to make drm_mode_gamma_set_ioctl() use drm_crtc_funcs.gamma_set if set or GAMMA_LUT property if not. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Philippe Cornu <philippe.cornu@st.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201211114237.213288-2-tomi.valkeinen@ti.com
2020-11-06drm/<drivers>: Constify struct drm_driverDaniel Vetter1-1/+1
Only the following drivers aren't converted: - amdgpu, because of the driver_feature mangling due to virt support. Subsequent patch will address this. - nouveau, because DRIVER_ATOMIC uapi is still not the default on the platforms where it's supported (i.e. again driver_feature mangling) - vc4, again because of driver_feature mangling - qxl, because the ioctl table is somewhere else and moving that is maybe a bit too much, hence the num_ioctls assignment prevents a const driver structure. - arcpgu, because that is stuck behind a pending tiny-fication series from me. - legacy drivers, because legacy requires non-const drm_driver. Note that for armada I also went ahead and made the ioctl array const. Only cc'ing the driver people who've not been converted (everyone else is way too much). v2: Fix one misplaced const static, should be static const (0day) v3: - Improve commit message (Sam) Acked-by: Sam Ravnborg <sam@ravnborg.org> Cc: kernel test robot <lkp@intel.com> Acked-by: Maxime Ripard <mripard@kernel.org> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Dave Airlie <airlied@redhat.com> Cc: Gerd Hoffmann <kraxel@redhat.com> Cc: virtualization@lists.linux-foundation.org Cc: Harry Wentland <harry.wentland@amd.com> Cc: Leo Li <sunpeng.li@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Eric Anholt <eric@anholt.net> Cc: Maxime Ripard <mripard@kernel.org> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: nouveau@lists.freedesktop.org Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201104100425.1922351-5-daniel.vetter@ffwll.ch
2020-11-02drm/atomic: Pass the full state to CRTC atomic begin and flushMaxime Ripard1-1/+1
The current atomic helpers have either their object state being passed as an argument or the full atomic state. The former is the pattern that was done at first, before switching to the latter for new hooks or when it was needed. Let's start convert all the remaining helpers to provide a consistent interface, starting with the CRTC's atomic_begin and atomic_flush. The conversion was done using the coccinelle script below, built tested on all the drivers and actually tested on vc4. virtual report @@ struct drm_crtc_helper_funcs *FUNCS; identifier old_crtc_state, old_state; identifier crtc; identifier f; @@ f(struct drm_crtc_state *old_crtc_state) { ... struct drm_atomic_state *old_state = old_crtc_state->state; <... - FUNCS->atomic_begin(crtc, old_crtc_state); + FUNCS->atomic_begin(crtc, old_state); ...> } @@ struct drm_crtc_helper_funcs *FUNCS; identifier old_crtc_state, old_state; identifier crtc; identifier f; @@ f(struct drm_crtc_state *old_crtc_state) { ... struct drm_atomic_state *old_state = old_crtc_state->state; <... - FUNCS->atomic_flush(crtc, old_crtc_state); + FUNCS->atomic_flush(crtc, old_state); ...> } @@ struct drm_crtc_helper_funcs *FUNCS; struct drm_crtc *crtc; struct drm_crtc_state *crtc_state; identifier dev, state; identifier f; @@ f(struct drm_device *dev, struct drm_atomic_state *state, ...) { <... - FUNCS->atomic_begin(crtc, crtc_state); + FUNCS->atomic_begin(crtc, state); ...> } @@ struct drm_crtc_helper_funcs *FUNCS; struct drm_crtc *crtc; struct drm_crtc_state *crtc_state; identifier dev, state; identifier f; @@ f(struct drm_device *dev, struct drm_atomic_state *state, ...) { <... - FUNCS->atomic_flush(crtc, crtc_state); + FUNCS->atomic_flush(crtc, state); ...> } @@ identifier crtc, old_state; @@ struct drm_crtc_helper_funcs { ... - void (*atomic_begin)(struct drm_crtc *crtc, struct drm_crtc_state *old_state); + void (*atomic_begin)(struct drm_crtc *crtc, struct drm_atomic_state *state); ... - void (*atomic_flush)(struct drm_crtc *crtc, struct drm_crtc_state *old_state); + void (*atomic_flush)(struct drm_crtc *crtc, struct drm_atomic_state *state); ... } @ crtc_atomic_func @ identifier helpers; identifier func; @@ ( static struct drm_crtc_helper_funcs helpers = { ..., .atomic_begin = func, ..., }; | static struct drm_crtc_helper_funcs helpers = { ..., .atomic_flush = func, ..., }; ) @ ignores_old_state @ identifier crtc_atomic_func.func; identifier crtc, old_state; @@ void func(struct drm_crtc *crtc, struct drm_crtc_state *old_state) { ... when != old_state } @ adds_old_state depends on crtc_atomic_func && !ignores_old_state @ identifier crtc_atomic_func.func; identifier crtc, old_state; @@ void func(struct drm_crtc *crtc, struct drm_crtc_state *old_state) { + struct drm_crtc_state *old_state = drm_atomic_get_old_crtc_state(state, crtc); ... } @ depends on crtc_atomic_func @ identifier crtc_atomic_func.func; expression E; type T; @@ void func(...) { ... - T state = E; + T crtc_state = E; <+... - state + crtc_state ...+> } @ depends on crtc_atomic_func @ identifier crtc_atomic_func.func; type T; @@ void func(...) { ... - T state; + T crtc_state; <+... - state + crtc_state ...+> } @@ identifier old_state; identifier crtc; @@ void vc4_hvs_atomic_flush(struct drm_crtc *crtc, - struct drm_crtc_state *old_state + struct drm_atomic_state *state ) { + struct drm_crtc_state *old_state = drm_atomic_get_old_crtc_state(state, crtc); ... } @@ identifier old_state; identifier crtc; @@ void vc4_hvs_atomic_flush(struct drm_crtc *crtc, - struct drm_crtc_state *old_state + struct drm_atomic_state *state ); @@ identifier old_state; identifier crtc; @@ void vmw_du_crtc_atomic_begin(struct drm_crtc *crtc, - struct drm_crtc_state *old_state + struct drm_atomic_state *state ) { ... } @@ identifier old_state; identifier crtc; @@ void vmw_du_crtc_atomic_begin(struct drm_crtc *crtc, - struct drm_crtc_state *old_state + struct drm_atomic_state *state ); @@ identifier old_state; identifier crtc; @@ void vmw_du_crtc_atomic_flush(struct drm_crtc *crtc, - struct drm_crtc_state *old_state + struct drm_atomic_state *state ) { ... } @@ identifier old_state; identifier crtc; @@ void vmw_du_crtc_atomic_flush(struct drm_crtc *crtc, - struct drm_crtc_state *old_state + struct drm_atomic_state *state ); @ depends on crtc_atomic_func @ identifier crtc_atomic_func.func; identifier old_state; identifier crtc; @@ void func(struct drm_crtc *crtc, - struct drm_crtc_state *old_state + struct drm_atomic_state *state ) { ... } @ include depends on adds_old_state @ @@ #include <drm/drm_atomic.h> @ no_include depends on !include && adds_old_state @ @@ + #include <drm/drm_atomic.h> #include <drm/...> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20201028123222.1732139-2-maxime@cerno.tech
2020-10-09drm/atomic: Pass the full state to CRTC atomic enable/disableMaxime Ripard1-2/+2
If the CRTC driver ever needs to access the full DRM state, it can't do so at atomic_enable / atomic_disable time since drm_atomic_helper_swap_state will have cleared the pointer from the struct drm_crtc_state to the struct drm_atomic_state before calling those hooks. In order to allow that, let's pass the full DRM state to atomic_enable and atomic_disable. The conversion was done using the coccinelle script below, built tested on all the drivers and actually tested on vc4. virtual report @@ struct drm_crtc_helper_funcs *FUNCS; identifier dev, state; identifier crtc, crtc_state; @@ disable_outputs(struct drm_device *dev, struct drm_atomic_state *state) { <... - FUNCS->atomic_disable(crtc, crtc_state); + FUNCS->atomic_disable(crtc, state); ...> } @@ struct drm_crtc_helper_funcs *FUNCS; identifier dev, state; identifier crtc, crtc_state; @@ drm_atomic_helper_commit_modeset_enables(struct drm_device *dev, struct drm_atomic_state *state) { <... - FUNCS->atomic_enable(crtc, crtc_state); + FUNCS->atomic_enable(crtc, state); ...> } @@ identifier crtc, old_state; @@ struct drm_crtc_helper_funcs { ... - void (*atomic_enable)(struct drm_crtc *crtc, struct drm_crtc_state *old_state); + void (*atomic_enable)(struct drm_crtc *crtc, struct drm_atomic_state *state); ... - void (*atomic_disable)(struct drm_crtc *crtc, struct drm_crtc_state *old_state); + void (*atomic_disable)(struct drm_crtc *crtc, struct drm_atomic_state *state); ... } @ crtc_atomic_func @ identifier helpers; identifier func; @@ ( static struct drm_crtc_helper_funcs helpers = { ..., .atomic_enable = func, ..., }; | static struct drm_crtc_helper_funcs helpers = { ..., .atomic_disable = func, ..., }; ) @ ignores_old_state @ identifier crtc_atomic_func.func; identifier crtc, old_state; @@ void func(struct drm_crtc *crtc, struct drm_crtc_state *old_state) { ... when != old_state } @ adds_old_state depends on crtc_atomic_func && !ignores_old_state @ identifier crtc_atomic_func.func; identifier crtc, old_state; @@ void func(struct drm_crtc *crtc, struct drm_crtc_state *old_state) { + struct drm_crtc_state *old_state = drm_atomic_get_old_crtc_state(state, crtc); ... } @ depends on crtc_atomic_func @ identifier crtc_atomic_func.func; expression E; type T; @@ void func(...) { ... - T state = E; + T crtc_state = E; <+... - state + crtc_state ...+> } @ depends on crtc_atomic_func @ identifier crtc_atomic_func.func; type T; @@ void func(...) { ... - T state; + T crtc_state; <+... - state + crtc_state ...+> } @ depends on crtc_atomic_func @ identifier crtc_atomic_func.func; identifier old_state; identifier crtc; @@ void func(struct drm_crtc *crtc, - struct drm_crtc_state *old_state + struct drm_atomic_state *state ) { ... } @ include depends on adds_old_state @ @@ #include <drm/drm_atomic.h> @ no_include depends on !include && adds_old_state @ @@ + #include <drm/drm_atomic.h> #include <drm/...> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/845aa10ef171fc0ea060495efef142a0c13f7870.1602161031.git-series.maxime@cerno.tech
2020-07-08drm/stm: repair runtime power managementMarek Vasut1-0/+3
Add missing pm_runtime_get_sync() into ltdc_crtc_atomic_enable() to match pm_runtime_put_sync() in ltdc_crtc_atomic_disable(), otherwise the LTDC might suspend via runtime PM, disable clock, and then fail to resume later on. The test which triggers it is roughly -- run qt5 application which uses eglfs platform and etnaviv, stop the application, sleep for 15 minutes, run the application again. This leads to a timeout waiting for vsync, because the LTDC has suspended, but did not resume. Fixes: 35ab6cfbf211 ("drm/stm: support runtime power management") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Yannick Fertré <yannick.fertre@st.com> Cc: Philippe Cornu <philippe.cornu@st.com> Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org> Cc: Vincent Abriou <vincent.abriou@st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> To: dri-devel@lists.freedesktop.org Cc: linux-stm32@st-md-mailman.stormreply.com Cc: linux-arm-kernel@lists.infradead.org Acked-by: Philippe Cornu <philippe.cornu@st.com> Tested-by: Yannick Fertre <yannick.fertre@st.com> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200229221649.90813-1-marex@denx.de
2020-07-08drm/stm: ltdc: remove call of pm-runtime functionsYannick Fertre1-16/+0
It is not necessary to suspend or stop the ltdc clocks to modify the pixel clock. Signed-off-by: Yannick Fertre <yannick.fertre@st.com> Acked-by: Philippe Cornu <philippe.cornu@st.com> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200701120402.6444-1-yannick.fertre@st.com
2020-06-10drm/stm: Set GEM CMA functions with DRM_GEM_CMA_DRIVER_OPS_WITH_DUMB_CREATEThomas Zimmermann1-6/+1
DRM_GEM_CMA_DRIVER_OPS_WITH_DUMB_CREATE sets the functions in struct drm_driver to their defaults. No functional changes are made. v2: * update for DRM_GEM_CMA_DRIVER_OPS_WITH_DUMB_CREATE Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by: Philippe Cornu <philippe.cornu@st.com> Reviewed-by: Emil Velikov <emil.velikov@collabora.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-35-tzimmermann@suse.de
2020-06-10drm/stm: Use GEM CMA object functionsThomas Zimmermann1-5/+1
Create GEM objects with drm_gem_cma_create_object_default_funcs(), which allocates the object and sets CMA's default object functions. Corresponding callbacks in struct drm_driver are cleared. No functional changes are made. Driver and object-function instances use the same callback functions, with the exception of vunmap. The implementation of vunmap is empty and left out in CMA's default object functions. v3: * convert to DRIVER_OPS macro in a separate patch Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by: Philippe Cornu <philippe.cornu@st.com> Reviewed-by: Emil Velikov <emil.velikov@collabora.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-34-tzimmermann@suse.de
2020-04-27drm/stm: ltdc: check number of endpointsYannick Fertre1-50/+52
Number of endpoints could exceed the fix value MAX_ENDPOINTS(2). Instead of increase simply this value, the number of endpoint could be read from device tree. Load sequence has been a little rework to take care of several panel or bridge which can be connected/disconnected or enable/disable. Signed-off-by: Yannick Fertre <yannick.fertre@st.com> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> Link: https://patchwork.freedesktop.org/patch/msgid/1582877258-1112-1-git-send-email-yannick.fertre@st.com
2020-03-26drm/stm: Drop explicit drm_mode_config_cleanup callDaniel Vetter1-6/+4
It's right above the drm_dev_put(). This is made possible by a preceeding patch which added a drmm_ cleanup action to drm_mode_config_init(), hence all we need to do to ensure that drm_mode_config_cleanup() is run on final drm_device cleanup is check the new error code for _init(). Aside: Another driver with a bit much devm_kzalloc, which should probably use drmm_kzalloc instead ... v2: Explain why this cleanup is possible (Laurent). v3: Use drmm_mode_config_init() for more clarity (Sam, Thomas) Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Thomas Zimmermann <tzimmermann@suse.de> Acked-by: Sam Ravnborg <sam@ravnborg.org> Acked-by: Philippe Cornu <philippe.cornu@st.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Cc: Yannick Fertre <yannick.fertre@st.com> Cc: Philippe Cornu <philippe.cornu@st.com> Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org> Cc: Vincent Abriou <vincent.abriou@st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: linux-stm32@st-md-mailman.stormreply.com Cc: linux-arm-kernel@lists.infradead.org Link: https://patchwork.freedesktop.org/patch/msgid/20200323144950.3018436-39-daniel.vetter@ffwll.ch
2020-02-26drm/bridge: Extend bridge API to disable connector creationLaurent Pinchart1-1/+1
Most bridge drivers create a DRM connector to model the connector at the output of the bridge. This model is historical and has worked pretty well so far, but causes several issues: - It prevents supporting more complex display pipelines where DRM connector operations are split over multiple components. For instance a pipeline with a bridge connected to the DDC signals to read EDID data, and another one connected to the HPD signal to detect connection and disconnection, will not be possible to support through this model. - It requires every bridge driver to implement similar connector handling code, resulting in code duplication. - It assumes that a bridge will either be wired to a connector or to another bridge, but doesn't support bridges that can be used in both positions very well (although there is some ad-hoc support for this in the analogix_dp bridge driver). In order to solve these issues, ownership of the connector should be moved to the display controller driver (where it can be implemented using helpers provided by the core). Extend the bridge API to allow disabling connector creation in bridge drivers as a first step towards the new model. The new flags argument to the bridge .attach() operation allows instructing the bridge driver to skip creating a connector. Unconditionally set the new flags argument to 0 for now to keep the existing behaviour, and modify all existing bridge drivers to return an error when connector creation is not requested as they don't support this feature yet. The change is based on the following semantic patch, with manual review and edits. @ rule1 @ identifier funcs; identifier fn; @@ struct drm_bridge_funcs funcs = { ..., .attach = fn }; @ depends on rule1 @ identifier rule1.fn; identifier bridge; statement S, S1; @@ int fn( struct drm_bridge *bridge + , enum drm_bridge_attach_flags flags ) { ... when != S + if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) { + DRM_ERROR("Fix bridge driver to make connector optional!"); + return -EINVAL; + } + S1 ... } @ depends on rule1 @ identifier rule1.fn; identifier bridge, flags; expression E1, E2, E3; @@ int fn( struct drm_bridge *bridge, enum drm_bridge_attach_flags flags ) { <... drm_bridge_attach(E1, E2, E3 + , flags ) ...> } @@ expression E1, E2, E3; @@ drm_bridge_attach(E1, E2, E3 + , 0 ) Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Acked-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-10-laurent.pinchart@ideasonboard.com
2020-02-13drm/stm: Convert to CRTC VBLANK callbacksThomas Zimmermann2-1/+1
VBLANK callbacks in struct drm_driver are deprecated in favor of their equivalents in struct drm_crtc_funcs. Convert stm over. Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Tested-by: Yannick Fertré <yannick.fertre@st.com> Acked-by: Philippe Cornu <philippe.cornu@st.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200123135943.24140-16-tzimmermann@suse.de
2020-02-13drm/stm: Convert to struct drm_crtc_helper_funcs.get_scanout_position()Thomas Zimmermann3-42/+39
The callback struct drm_driver.get_scanout_position() is deprecated in favor of struct drm_crtc_helper_funcs.get_scanout_position(). Convert stm over. Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Acked-by: Philippe Cornu <philippe.cornu@st.com> Tested-by: Yannick Fertré <yannick.fertre@st.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200123135943.24140-15-tzimmermann@suse.de
2020-02-04drm/stm: dsi: stm mipi dsi doesn't print error on probe deferralEtienne Carriere1-1/+3
Change DSI driver to not print an error trace when probe is deferred for a clock resource. Signed-off-by: Etienne Carriere <etienne.carriere@st.com> Reviewed-by: Philippe Cornu <philippe.cornu@st.com> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> Link: https://patchwork.freedesktop.org/patch/msgid/1579602245-7577-1-git-send-email-yannick.fertre@st.com
2020-02-04drm/stm: ltdc: check crtc state before enabling LIEYannick Fertre1-1/+6
Following investigations of a hardware bug, the LIE interrupt can occur while the display controller is not activated. LIE interrupt (vblank) don't have to be set if the CRTC is not enabled. Signed-off-by: Yannick Fertre <yannick.fertre@st.com> Acked-by: Philippe Cornu <philippe.cornu@st.com> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> Link: https://patchwork.freedesktop.org/patch/msgid/1579601650-7055-1-git-send-email-yannick.fertre@st.com
2020-02-04drm/stm: ltdc: add number of interruptsYannick Fertre2-15/+16
The number of interrupts depends on the ltdc version. Don't try to get interrupt which not exist, avoiding kernel warning messages. Signed-off-by: Yannick Fertre <yannick.fertre@st.com> Acked-by: Philippe Cornu <philippe.cornu@st.com> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> Link: https://patchwork.freedesktop.org/patch/msgid/1579601632-7001-1-git-send-email-yannick.fertre@st.com
2019-12-20drm/stm: ltdc: move pinctrl to encoder mode setYannick Fertré1-6/+18
The pin control must be set to default as soon as possible to establish a good video link between tv & bridge hdmi (encoder mode set is call before encoder enable). Signed-off-by: Yannick Fertre <yannick.fertre@st.com> Acked-by: Philippe Cornu <philippe.cornu@st.com> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> Link: https://patchwork.freedesktop.org/patch/msgid/1574850218-13257-1-git-send-email-yannick.fertre@st.com
2019-12-16drm/bridge/synopsys: dsi: driver-specific configuration of phy timingsHeiko Stuebner1-0/+13
The timing values for dw-dsi are often dependent on the used display and according to Philippe Cornu will most likely also depend on the used phy technology in the soc-specific implementation. To solve this and allow specific implementations to define them as needed add a new get_timing callback to phy_ops and call this from the dphy_timing function to retrieve the necessary values for the specific mode. Right now this handles the hs2lp + lp2hs where Rockchip SoCs need handling according to the phy speed, while STM seems to be ok with static values. changes in v5: - rebase on 5.5-rc1 - merge into px30 dsi series to prevent ordering conflicts changes in v4: - rebase to make it directly fit on top of drm-misc-next after all changes in v3: - check existence of phy_ops->get_timing in __dw_mipi_dsi_probe() - emit actual error when get_timing() call fails - add tags from Philippe and Yannick changes in v2: - add driver-specific handling, don't force all bridge users to use the same timings, as suggested by Philippe Suggested-by: Philippe Cornu <philippe.cornu@st.com> Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philippe Cornu <philippe.cornu@st.com> Tested-by: Yannick Fertre <yannick.fertre@st.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191209143130.4553-2-heiko@sntech.de
2019-09-16drm/stm: dsi: higher pll out only in video burst modeYannick Fertré1-1/+4
In order to better support video non-burst modes, the +20% on pll out is added only in burst mode. Signed-off-by: Philippe Cornu <philippe.cornu@st.com> Signed-off-by: Yannick Fertré <yannick.fertre@st.com> Reviewed-by: Yannick Fertré <yannick.fertre@st.com> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/1568278589-20400-1-git-send-email-yannick.fertre@st.com
2019-09-09drm/stm: ltdc: add pinctrl for DPI encoder modeYannick Fertré1-0/+35
The implementation of functions encoder_enable and encoder_disable make possible to control the pinctrl according to the encoder type. The pinctrl must be activated only if the encoder type is DPI. This helps to move the DPI-related pinctrl configuration from all the panel or bridge to the LTDC dt node. Reviewed-by: Philippe Cornu <philippe.cornu@st.com> Signed-off-by: Yannick Fertré <yannick.fertre@st.com> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/1567761708-31777-1-git-send-email-yannick.fertre@st.com
2019-09-08drm/bridge: panel: Infer connector type from panel by defaultLaurent Pinchart1-2/+2
The drm panel bridge creates a connector using a connector type explicitly passed by the display controller or bridge driver that instantiates the panel bridge. Now that drm_panel reports its connector type, we can use it to avoid passing an explicit (and often incorrect) connector type to drm_panel_bridge_add() and devm_drm_panel_bridge_add(). Several drivers report incorrect or unknown connector types to userspace. Reporting a different type may result in a breakage. For that reason, rename (devm_)drm_panel_bridge_add() to (devm_)drm_panel_bridge_add_typed(), and add new (devm_)drm_panel_bridge_add() functions that use the panel connector type. Update all callers of (devm_)drm_panel_bridge_add() to the _typed function, they will be converted one by one after testing. The panel drivers have been updated with the following Coccinelle semantic patch, with manual inspection and fixes to indentation. @@ expression bridge; expression dev; expression panel; identifier type; @@ ( -bridge = drm_panel_bridge_add(panel, type); +bridge = drm_panel_bridge_add_typed(panel, type); | -bridge = devm_drm_panel_bridge_add(dev, panel, type); +bridge = devm_drm_panel_bridge_add_typed(dev, panel, type); ) Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190904132804.29680-3-laurent.pinchart@ideasonboard.com
2019-07-25drm/stm: attach gem fence to atomic stateAhmad Fatoum1-0/+2
To properly synchronize with other devices the fence from the GEM object backing the framebuffer needs to be attached to the atomic state, so the commit work can wait on fence signaling. Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Acked-by: Philippe Cornu <philippe.cornu@st.com> Tested-by: Philippe Cornu <philippe.cornu@st.com> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190712084228.8338-1-l.stach@pengutronix.de
2019-07-01drm/stm: drop use of drmP.hSam Ravnborg1-3/+7
Drop use of the deprecated header file drmP.h from the sole user in the stm driver. Replace with necessary include files. Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Cc: Yannick Fertre <yannick.fertre@st.com> Cc: Philippe Cornu <philippe.cornu@st.com> Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org> Cc: Vincent Abriou <vincent.abriou@st.com> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: linux-stm32@st-md-mailman.stormreply.com Cc: linux-arm-kernel@lists.infradead.org Cc: linux-stm32@st-md-mailman.stormreply.com Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190630061922.7254-4-sam@ravnborg.org
2019-06-21drm/stm: Drop drm_gem_prime_export/importDaniel Vetter1-2/+0
They're the default. Aside: Would be really nice to switch the others over to drm_gem_object_funcs. Acked-by: Philippe Cornu <philippe.cornu@st.com> Reviewed-by: Eric Anholt <eric@anholt.net> Reviewed-by: Emil Velikov <emil.velikov@collabora.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Cc: Yannick Fertre <yannick.fertre@st.com> Cc: Philippe Cornu <philippe.cornu@st.com> Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org> Cc: Vincent Abriou <vincent.abriou@st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: linux-stm32@st-md-mailman.stormreply.com Cc: linux-arm-kernel@lists.infradead.org Link: https://patchwork.freedesktop.org/patch/msgid/20190614203615.12639-31-daniel.vetter@ffwll.ch
2019-06-21drm/prime: Actually remove DRIVER_PRIME everywhereDaniel Vetter1-2/+1
Split out to make the functional changes stick out more. All places where DRIVER_PRIME was used have been removed in previous patches already. v2: amdgpu gained DRIVER_SYNCOBJ_TIMELINE. v3: amdgpu lost DRIVER_SYNCOBJ_TIMELINE. v4: Don't add a space in i915_drv.c (Sam) v5: Add note that previous patches removed all the DRIVER_PRIME users already (Emil). v6: Fixupe ingenic (new driver) while applying. Cc: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Emil Velikov <emil.velikov@collabora.com> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Cc: amd-gfx@lists.freedesktop.org Cc: etnaviv@lists.freedesktop.org Cc: freedreno@lists.freedesktop.org Cc: intel-gfx@lists.freedesktop.org Cc: lima@lists.freedesktop.org Cc: linux-amlogic@lists.infradead.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-arm-msm@vger.kernel.org Cc: linux-aspeed@lists.ozlabs.org Cc: linux-renesas-soc@vger.kernel.org Cc: linux-rockchip@lists.infradead.org Cc: linux-samsung-soc@vger.kernel.org Cc: linux-stm32@st-md-mailman.stormreply.com Cc: linux-tegra@vger.kernel.org Cc: nouveau@lists.freedesktop.org Cc: NXP Linux Team <linux-imx@nxp.com> Cc: spice-devel@lists.freedesktop.org Cc: virtualization@lists.linux-foundation.org Cc: VMware Graphics <linux-graphics-maintainer@vmware.com> Cc: xen-devel@lists.xenproject.org Link: https://patchwork.freedesktop.org/patch/msgid/20190617153924.414-1-daniel.vetter@ffwll.ch
2019-06-20drm/stm: drv: fix suspend/resumeYannick Fertré1-7/+8
Without this fix, the system can not go in "suspend" mode due to an error in drv_suspend function. Fixes: 35ab6cfbf211 ("drm/stm: support runtime power management") Signed-off-by: Yannick Fertré <yannick.fertre@st.com> Acked-by: Philippe Cornu <philippe.cornu@st.com> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/1560755897-5002-1-git-send-email-yannick.fertre@st.com
2019-06-12drm/stm: dsi: add power on/off phy opsYannick Fertré1-1/+20
These new physical operations are helpful to power_on/off the dsi wrapper. If the dsi wrapper is powered in video mode, the display controller (ltdc) register access will hang when DSI fifos are full. Signed-off-by: Yannick Fertré <yannick.fertre@st.com> Acked-by: Philippe Cornu <philippe.cornu@st.com> Tested-by: Philippe Cornu <philippe.cornu@st.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/1558952499-15418-3-git-send-email-yannick.fertre@st.com
2019-06-07drm/stm: support runtime power managementYannick Fertré2-24/+86
This patch enables runtime power management (runtime PM) support for the display controller. pm_runtime_enable() and pm_runtime_disable() are added during ltdc load and unload respectively. pm_runtime_get_sync() and pm_runtime_put_sync() are added for ltdc register access. Signed-off-by: Yannick Fertré <yannick.fertre@st.com> Acked-by: Philippe Cornu <philippe.cornu@st.com> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/1559550722-14091-1-git-send-email-yannick.fertre@st.com
2019-06-07drm/stm: ltdc: No message if probeYannick Fertré1-1/+1
Print display controller hardware version in debug mode only. Signed-off-by: Yannick Fertré <yannick.fertre@st.com> Acked-by: Philippe Cornu <philippe.cornu@st.com> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/1559550694-14042-1-git-send-email-yannick.fertre@st.com
2019-05-28Merge remote-tracking branch 'drm/drm-next' into drm-misc-nextMaarten Lankhorst2-0/+2
This picks up rc2 for us as well. Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
2019-05-28drm/stm: ltdc: restore calls to clk_{enable/disable}Benjamin Gaignard1-0/+2
Restore calls to clk_{enable/disable} deleted after applying the wrong version of the patch Fixes: fd6905fca4f0 ("drm/stm: ltdc: remove clk_round_rate comment") Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Acked-by: Philippe Cornu <philippe.cornu@st.com> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190527115830.15836-1-benjamin.gaignard@st.com
2019-05-28Merge tag 'drm-misc-next-2019-05-24' of git://anongit.freedesktop.org/drm/drm-misc into drm-nextDave Airlie2-31/+96
drm-misc-next for v5.3, try #2: UAPI Changes: - Add HDR source metadata property. - Make drm.h compile on GNU/kFreeBSD by including stdint.h - Clarify how the userspace reviewer has to review new kernel UAPI. - Clarify that for using new UAPI, merging to drm-next or drm-misc-next should be enough. Cross-subsystem Changes: - video/hdmi: Add unpack function for DRM infoframes. - Device tree bindings: * Updating a property for Mali Midgard GPUs * Updating a property for STM32 DSI panel * Adding support for FriendlyELEC HD702E 800x1280 panel * Adding support for Evervision VGG804821 800x480 5.0" WVGA TFT panel * Adding support for the EDT ET035012DM6 3.5" 320x240 QVGA 24-bit RGB TFT. * Adding support for Three Five displays TFC S9700RTWV43TR-01B 800x480 panel with resistive touch found on TI's AM335X-EVM. * Adding support for EDT ETM0430G0DH6 480x272 panel. - Add OSD101T2587-53TS driver with DT bindings. - Add Samsung S6E63M0 panel driver with DT bindings. - Add VXT VL050-8048NT-C01 800x480 panel with DT bindings. - Dma-buf: - Make mmap callback actually optional. - Documentation updates. - Fix debugfs refcount inbalance. - Remove unused sync_dump function. - Fix device tree bindings in drm-misc-next after a botched merge. Core Changes: - Add support for HDR infoframes and related EDID parsing. - Remove prime sg_table caching, now done inside dma-buf. - Add shiny new drm_gem_vram helpers for simple VRAM drivers; with some fixes to the new API on top. - Small fix to job cleanup without timeout handler. - Documentation fixes to drm_fourcc. - Replace lookups of drm_format with struct drm_format_info; remove functions that become obsolete by this conversion. - Remove double include in bridge/panel.c and some drivers. - Remove drmP.h include from drm/edid and drm/dp. - Fix null pointer deref in drm_fb_helper_hotplug_event(). - Remove most members from drm_fb_helper_crtc, only mode_set is kept. - Remove race of fb helpers with userspace; only restore mode when userspace is not master. - Move legacy setup from drm_file.c to drm_legacy_misc.c - Rework scheduler job destruction. - drm/bus was removed, remove from TODO. - Add __drm_atomic_helper_crtc_reset() to subclass crtc_state, and convert some drivers to use it (conversion is not complete yet). - Bump vblank timeout wait to 100 ms for atomic. - Docbook fix for drm_hdmi_infoframe_set_hdr_metadata. Driver Changes: - sun4i: Use DRM_GEM_CMA_VMAP_DRIVER_OPS instead of definining manually. - v3d: Small cleanups, adding support for compute shaders, reservation/synchronization fixes and job management refactoring, fixes MMU and debugfs. - lima: Fix null pointer in irq handler on startup, set default timeout for scheduled jobs. - stm/ltdc: Assorted fixes and adding FB modifier support. - amdgpu: Avoid hw reset if guilty job was already signaled. - virtio: Add seqno to fences, add trace events, use correct flags for fence allocation. - Convert AST, bochs, mgag200, vboxvideo, hisilicon to the new drm_gem_vram API. - sun6i_mipi_dsi: Support DSI GENERIC_SHORT_WRITE_2 transfers. - bochs: Small fix to use PTR_RET_OR_ZERO and driver unload. - gma500: header fixes - cirrus: Remove unused files. - mediatek: Fix compiler warning after merging the HDR series. - vc4: Rework binner bo handling. Signed-off-by: Dave Airlie <airlied@redhat.com> From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/052875a5-27ba-3832-60c2-193d950afdff@linux.intel.com
2019-05-24drm/stm: dsi: check hardware versionYannick Fertré1-1/+23
Check version of DSI hardware IP. Only versions 1.30 & 1.31 are supported. Signed-off-by: Yannick Fertré <yannick.fertre@st.com> Acked-by: Philippe Cornu <philippe.cornu@st.com> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/1557500579-19720-1-git-send-email-yannick.fertre@st.com
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.