| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Expand HDMI PHY clock driver to support second clock parent.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-20-jernej.skrabec@siol.net
|
|
Some DW HDMI PHYs, like those found in A64 and R40 SoCs, can select
between two clock parents.
Add code which reads second PLL from DT.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-19-jernej.skrabec@siol.net
|
|
DW HDMI PHY driver and PHY clock driver share same registers. Make sure
that DW HDMI PHY setup code doesn't change any clock related bits.
During initialization, set PHY PLL parent bit to 0.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-18-jernej.skrabec@siol.net
|
|
Current DW HDMI PHY code never prepares and enables PHY clock after it is
created. It's just used as it is. This may work in some cases, but it's
clearly wrong. Fix it by adding proper calls to enable/disable PHY
clock.
Fixes: 4f86e81748fe ("drm/sun4i: Add support for H3 HDMI PHY variant")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-17-jernej.skrabec@siol.net
|
|
Both mixers have similar capabilities as others SoCs with DE2.
First mixer has 1 VI and 3 UI planes and supports HW scaling on all
planes.
Second mixer has 1 VI and 1 UI planes and also supports HW scaling on
all planes.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-15-jernej.skrabec@siol.net
|
|
TV TCONs are always connected to TV or HDMI encoder, so it doesn't make
sense to check if panel or bridge is connected to them.
Check if TCON has channel 0 and only then check for connected panel or
bridges.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-13-jernej.skrabec@siol.net
|
|
LVDS and RGB interfaces are always connected to TCONs which have channel
0. It doesn't make sense to try to init them on TV TCONs.
Add a check if TCON has channel 0 before trying to init LVDS or RGB
interface.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-12-jernej.skrabec@siol.net
|
|
Current "old" method to find engine worked pretty well for DE2. However,
it doesn't work when TCON TOP is between mixer (engine) and TCON. TCON
TOP has multiple input ports, but current engine search algorithm
expects only one.
This can be fixed by first looking for output port id and selecting
matching input by subtracting 1 for the next round. This work even if
there is only one input and output.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-11-jernej.skrabec@siol.net
|
|
TV TCONs (channel 1 only) are always connected to TV or HDMI encoder.
Because of that, all output endpoints on such TCON node will point to a
encoder which is part of component framework.
Correct current graph traversing algorithm in such way that it doesn't
skip output enpoints with id 0 on TV TCONs.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-10-jernej.skrabec@siol.net
|
|
TCON TOP is different from other nodes in graph by having 3 input and 3
output ports. Additionally, connection to TV TCON might lead back to
HDMI mux input port, creating loops.
Add support for traversing such graph.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-9-jernej.skrabec@siol.net
|
|
Until now, each node has one input port and one output port. However,
with TCON TOP this is no longer true. It has 3 input and 3 output ports.
In order to prepare to this situation, split out the code which checks
all endpoints in input port and adds available components to fifo.
This patch doesn't do any functional change.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-8-jernej.skrabec@siol.net
|
|
sun4i_drv_add_endpoints() has a memory leak since it uses of_node_put()
when remote is equal to NULL and does nothing when remote has a valid
pointer.
Invert the logic to fix memory leak.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-7-jernej.skrabec@siol.net
|
|
As already described in DT binding, TCON TOP is responsible for
configuring display pipeline. In this initial driver focus is on HDMI
pipeline, so TVE and LCD configuration is not implemented.
Implemented features:
- HDMI source selection
- clock driver (TCON and DSI gating)
- connecting mixers and TCONS
Something similar also existed in previous SoCs, except that it was part
of first TCON.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-6-jernej.skrabec@siol.net
|
|
Currently, amdgpu_do_flip() spinlocks crtc->dev->event_lock and
releases it only after committing updates to the stream.
dc_commit_updates_for_stream() should be moved out of
spinlock for the below reasons:
1. event_lock is supposed to protect access to acrct->pflip_status _only_
2. dc_commit_updates_for_stream() has potential sleep's
and also its not appropriate to be in an atomic state
for such long sequences of code.
Signed-off-by: Shirish S <shirish.s@amd.com>
Suggested-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Support new VCN FW version naming convention:
[31, 28] for VEP interface major version if applicable
[27, 24] for decode interface major version
[23, 20] for encode interface major version
[19, 12] for encode interface minor version
[11, 0] for firmware revision
Bit 20-23, it is encode major and non-zero for new naming convention.
This field is part of version minor and DRM_DISABLED_FLAG in old naming
convention. Since the latest version minor is 0x5B and DRM_DISABLED_FLAG
is zero in old naming convention, this field is always zero so far.
These four bits are used to tell which naming convention is present.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Fang, Peter <Peter.Fang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Here is the UBSAN dump:
[ 3.866656] index 2 is out of range for type 'amdgpu_uvd_inst [2]'
[ 3.866693] Workqueue: events work_for_cpu_fn
[ 3.866702] Call Trace:
[ 3.866710] dump_stack+0x85/0xc5
[ 3.866719] ubsan_epilogue+0x9/0x40
[ 3.866727] __ubsan_handle_out_of_bounds+0x89/0x90
[ 3.866737] ? rcu_read_lock_sched_held+0x58/0x60
[ 3.866746] ? __kmalloc+0x26c/0x2d0
[ 3.866846] amdgpu_fence_driver_start_ring+0x259/0x280 [amdgpu]
[ 3.866896] amdgpu_ring_init+0x12c/0x710 [amdgpu]
[ 3.866906] ? sprintf+0x42/0x50
[ 3.866956] amdgpu_gfx_kiq_init_ring+0x1bc/0x3a0 [amdgpu]
[ 3.867009] gfx_v8_0_sw_init+0x1ad3/0x2360 [amdgpu]
[ 3.867062] ? smu7_init+0xec/0x160 [amdgpu]
[ 3.867109] amdgpu_device_init+0x112c/0x1dc0 [amdgpu]
'ring->me' might be set as 2 with 'amdgpu_gfx_kiq_init_ring', that would
cause out of range for 'amdgpu_uvd_inst[2]'.
v2: simplified with ring type
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This adds a new driver for display panels that use the Ilitek ILI9341
controller. It currently supports a single display panel, namely
the YX240QV29-T (e.g. Adafruit 2.4" TFT).
The init sequence is from the Adafruit Python library for the ILI9341
controller. https://github.com/adafruit/Adafruit_Python_ILI9341
Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180525193623.15533-5-david@lechnology.com
|
|
In the next^W forthcoming patch, we will start to defer retiring the
request from the engine list if it is still active on the submission
backend. To preserve the semantics that after wait-for-idle completes
the system is idle and fully retired, we need to therefore wait for the
backends to idle before calling i915_retire_requests().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180627115334.16282-1-chris@chris-wilson.co.uk
|
|
Now that mtk_drm_fb is an empty wrapper around drm_framebuffer, we can
just delete it.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Since drm_framebuffer can now store GEM objects directly, place them
there rather than in our own subclass. As this makes the framebuffer
create_handle and destroy functions the same as the GEM framebuffer
helper, we can reuse those.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
|
|
We cannot create a framebuffer with no objects, so there's no point
testing for it.
v2: Remove the error entirely. (Sean, CK, Thierry)
Signed-off-by: Daniel Stone <daniels@collabora.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
|
|
This patch add support for the Mediatek MT2712 DISP subsystem.
There are two OVL engine and three disp output in MT2712.
Signed-off-by: Stu Hsieh <stu.hsieh@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
|
|
Split the long line into two short line to make sure eache line
not over 80 characters.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
|
|
Russell King reported:
"When removing and reloading the etnaviv module, the following splat
occurs:
sysfs: cannot create duplicate filename '/devices/platform/etnaviv'
CPU: 0 PID: 1471 Comm: modprobe Not tainted 4.17.0+ #1608
Hardware name: Marvell Dove (Cubox)
Backtrace:
[<c00157d4>] (dump_backtrace) from [<c0015b8c>] (show_stack+0x18/0x1c)
r6:ef033e38 r5:ee07b340 r4:edb9d000 r3:00000000
[<c0015b74>] (show_stack) from [<c0620784>] (dump_stack+0x20/0x28)
[<c0620764>] (dump_stack) from [<c01bcd24>] (sysfs_warn_dup+0x5c/0x70)
[<c01bccc8>] (sysfs_warn_dup) from [<c01bce14>] (sysfs_create_dir_ns+0x90/0x98)
..."
Commit 246774d17fc0 ("drm/etnaviv: remove the need for a gpu-subsystem
DT node") introduced DRM registration via
platform_device_register_simple(), but missed to call
platform_device_unregister() inside etnaviv_exit().
Fix the problem by calling platform_device_unregister() inside
etnaviv_exit(). While at it, also rearrange the function calls
in the exit path to make them happen in the opposite order of
registration.
Tested on a imx6-sabresd board.
Cc: <stable@vger.kernel.org>
Fixes: 246774d17fc0 ("drm/etnaviv: remove the need for a gpu-subsystem DT node")
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
|
|
platform_device_register_simple() may fail, so we should better
check its return value and propagate it in the case of error.
Cc: <stable@vger.kernel.org>
Fixes: 246774d17fc0 ("drm/etnaviv: remove the need for a gpu-subsystem DT node")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
|
|
Add the definition for ICL power wells and their mapping to power
domains. On ICL there are 3 power well control registers, we'll select
the correct one based on higher bits of the power well ID. The offset
for the control and status flags within this register is based on the
lower bits of the ID as on older platforms.
As the DC state programming is also the same as on old platforms we can
reuse the corresponding helpers. For this we mark here the DC-off power
well as shared among multiple platforms.
Other than the above the delta between old platforms and ICL:
- Pipe C has its own power well, so we can save some additional power in the
pipe A+B and (non-eDP) pipe A configurations.
- Power wells for port E/F DDI/AUX IO and Thunderbolt 1-4 AUX IO
v2:
- Rebase on drm-tip after prep patch for this was merged there as
requested by Paulo.
- Actually add the new AUX and DDI power well control regs (Rakshmi)
v3:
- Fix power well register names in code comments
- Add TBT AUX->power well 3 dependency
v4:
- Rebase
v5:
- Detach AUX power wells from the INIT power domain. These power wells
can only be enabled in a TC/TBT connected state and otherwise not
needed during driver initialization.
v6:
- Use _MMIO_PORT(...) instead _MMIO(_PICK(...)) (Paulo)
Fix checkpatch warnings.
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Rakshmi Bhatia <rakshmi.bhatia@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com> (v1)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626142232.22361-1-imre.deak@intel.com
|
|
linebuffer mode should be LB_YUV_3840X5 when width is bigger than 1280
in yuv mode.
Separate yuv and rgb case makes the scl_vop_cal_lb_mode() logic clearer.
Signed-off-by: Sandy Huang <hjc@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1530001004-25036-1-git-send-email-hjc@rock-chips.com
|
|
Use drm_crtc_mask() where appropriate.
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: "Heiko Stübner" <heiko@sntech.de>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626194716.12522-7-ville.syrjala@linux.intel.com
|
|
Sink can be configured to calculate the CRC over the static frame and
compare with the CRC calculated and transmited in the VSC SDP by
source, if there is a mismatch sink will do a short pulse in HPD
and set DP_PSR_LINK_CRC_ERROR in DP_PSR_ERROR_STATUS.
Spec: 7723
v6:
andling DP_PSR_LINK_CRC_ERROR here and remove "bdw+" from commit
message
v4:
patch moved to after 'drm/i915/psr: Avoid PSR exit max time timeout'
to avoid touch in 2 patches EDP_PSR_DEBUG.
v3:
disabling PSR instead of exiting on error
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626201644.21932-5-jose.souza@intel.com
|
|
Specification requires that max time should be masked from bdw and
forward but it can be also safely enabled to hsw.
This will make PSR exits more deterministic and only when really
needed. If this was used to fix a issue in some panel than can
only self-refresh for a few seconds, that panel will interrupt
and assert one of the PSR errors handled in:
'drm/i915/psr: Handle PSR RFB storage error' and
'drm/i915/psr: Begin to handle PSR/PSR2 errors set by sink'
Spec: 21664
v4:
patch moved to before 'drm/i915/psr/bdw+: Enable CRC check in the
static frame on the sink side' to avoid touch in 2 patches
EDP_PSR_DEBUG.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626201644.21932-4-jose.souza@intel.com
|
|
Sink will interrupt source when it have any PSR error.
DP_PSR_VSC_SDP_UNCORRECTABLE_ERROR is a PSR2 but already
handling it here.
The only missing error to be handled is DP_PSR_LINK_CRC_ERROR that
will be taken in care in a futher patch.
v6:
not handling DP_PSR_LINK_CRC_ERROR here
v5:
handling all PSR errors here, so the commit message and
comment have changed
v3:
disabling PSR instead of exiting on error
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626201644.21932-3-jose.souza@intel.com
|
|
eDP spec states that sink device will do a short pulse in HPD
line when there is a PSR/PSR2 error that needs to be handled by
source, this is handling the first and most simples error:
DP_PSR_SINK_INTERNAL_ERROR.
Here taking the safest approach and disabling PSR(at least until
the next modeset), to avoid multiple rendering issues due to
bad pannels.
v5:
added lockdep_assert in psr_disable and renamed psr_disable()
to intel_psr_disable_locked()
v4:
Using CAN_PSR instead of HAS_PSR in intel_psr_short_pulse
v3:
disabling PSR instead of exiting on error
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626201644.21932-2-jose.souza@intel.com
|
|
It was only used in VLV/CHV so after the removal of the PSR support
for those platforms it is not necessary any more.
v7: Rebased
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626201644.21932-1-jose.souza@intel.com
|
|
Depending whether PSR1 or PSR2 was configured, we print a warning if the
corresponding control mmio indicated PSR was erroneously enabled. As
Chris pointed out, it makes more sense to check for both the mmio's
since we expect neither PSR1 nor PSR2 to be enabled when psr_activate() is
called.
v2: Read PSR2 control register only on supported platforms (Rodrigo)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626090522.17682-1-dhinakaran.pandiyan@intel.com
|
|
Commit 5422b37c907e ("drm/i915/psr: Kill delays when activating psr
back.") switched from delayed work to the plain variant and while doing so
removed the check for work_busy() before scheduling a PSR activation.
This appears to cause consecutive executions of psr_activate() in this
scenario - after a worker picks up the PSR work item for execution and
before the work function can acquire the PSR mutex, a psr_flush() can
get hold of the mutex and schedule another PSR work. Without a psr_exit()
between the two psr_activate() calls, warning messages get printed.
Further, since we drop the mutex in the midst of psr_work() to wait for
PSR to idle, another work item can also get scheduled. Fix this by
returning if PSR was already active.
Fixes: 5422b37c907e ("drm/i915/psr: Kill delays when activating psr back.")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106948
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625054741.3919-1-dhinakaran.pandiyan@intel.com
|
|
At some point we introduced the function pointers
on PSR code to help with VLV/CHV separation logic
because it had a different HW implementation from PSR.
Since all converged to HSW PSR and we dropped the
VLV/CHV support, let's also kill the useless function
pointers and leave the code cleaner.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626052536.15137-1-rodrigo.vivi@intel.com
|
|
Fix the following compile warning:
warning: unused variable ‘psbfb’ [-Wunused-variable]
struct psb_framebuffer *psbfb = to_psb_fb(fb);
Fixes: c7cbed560ce2 ("drm/gma500: Fix Medfield for drm_framebuffer move")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625123355.GA16757@embeddedor.com
|
|
fb is being dereferenced before it is null checked, hence there
is a potential null pointer dereference.
Fix this by moving the pointer dereference after fb has been
properly null checked at line 74: if (!fb)
Addresses-Coverity-ID: 1470169 ("Dereference before null check")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625121844.GA12466@embeddedor.com
|
|
So far we got an AUX power domain reference only for the duration of DP
AUX transfers. However, the following suggests that we also need these
for main link functionality:
- The specification doesn't state whether it's needed or not for main
link functionality, but suggests that these power wells need to be
enabled already during display core initialization (Sequences to
Initialize Display).
- For PSR we need to keep the AUX power well enabled.
- On ICL combo PHY ports (non-TC) the AUX power well is needed for
link training too: while the port is enabled with a DP link training
test pattern trying to toggle the AUX power well will time out.
- On ICL MG PHY ports (TC) the AUX power well is needed also for main
link functionality (both in DP and HDMI modes).
- Windows enables these power wells both for main and AUX lane
functionality.
Based on the above take an AUX power reference for main link
functionality too. This makes a difference only on GEN10+ (GLK+)
platforms, where we have separate port specific AUX power wells.
For PSR we still need to distinguish between port A and the other
ports, since on port A DC states must stay enabled for main link
functionality, but DC states must be disabled for driver initiated
AUX transfers. So re-use the corresponding helper from intel_psr.c.
Since we take now a reference for main link functionality on all DP
ports we can forgo taking the separate power ref for PSR functionality.
v2:
- Make sure DC states stay enabled when taking the ref on port A.
(Ville)
v3: (Ville)
- Fix comment about logic for encoders without a crtc state and
add FIXME note for a simplification to avoid calling get_power_domains
in such cases.
- Use intel_crtc_has_dp_encoder() instead !intel_crtc_has_type(HDMI).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
[Clarified code comments in intel_ddi_main_link_aux_domain() and
intel_ddi_get_power_domains() (Imre)]
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180621184449.26634-1-imre.deak@intel.com
|
|
If 'platform_get_resource_byname()' fails, we should release some resources
before leaving, as already done in the other error handling path of the
function.
Fixes: acaa3f13b8dd ("drm/meson: Fix potential NULL dereference in meson_drv_bind_master()")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611165335.24542-1-christophe.jaillet@wanadoo.fr
|
|
This patch unifies the naming of DRM functions for reference counting
of struct drm_gem_object. The resulting code is more aligned with the
rest of the Linux kernel interfaces.
Signed-off-by: Thomas Zimmermann <contact@tzimmermann.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625152148.29555-1-contact@tzimmermann.org
|
|
The LHR050H41 panel is the panel shipped with the BananaPi M2-Magic, and is
based on the Ilitek ILI9881c Controller. Add a driver for it, modelled
after the other Ilitek controller drivers.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/acb5453112ab7c7b801cf4f1669e351b391e77e8.1527587352.git-series.maxime.ripard@bootlin.com
|
|
The driver doesn't support scaling, but when an atomic test is done
it repeatedly spits out this warning which isn't particularly useful.
So just remove the error message.
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Rongrong Zou <zourongrong@gmail.com>
Cc: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Cc: Chen Feng <puck.chen@hisilicon.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Peter Griffin <peter.griffin@linaro.org>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1529622076-20386-1-git-send-email-john.stultz@linaro.org
|
|
Due to how we only release the pining on the context state on
retirement and never track activity on the context vma itself, the
object can never be active at the point of release. Replace the
conditional transfer of ownership onto an active-reference with an
assert that the object is idle.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625100604.22598-2-chris@chris-wilson.co.uk
|
|
As we may cancel the ce->state allocation during context pinning (but
crucially after we mark ce as operational), that means we may be asked
to destroy a nonexistent ce->state. Given the choice in handing a
complex error path on pinning, and just ignoring the lack of state in
destroy, choice the latter for simplicity.
Reported-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625100604.22598-1-chris@chris-wilson.co.uk
|
|
If we avoid cleaning up the old state immediately in
intel_atomic_commit_tail() and defer it to a second task, we can avoid
taking heavily contended locks when the caller is ready to procede.
Subsequent modesets will wait for the cleanup operation (either directly
via the ordered modeset wq or indirectly through the atomic helperr)
which keeps the number of inflight cleanup tasks in check.
As an example, during reset an immediate modeset is performed to disable
the displays before the HW is reset, which must avoid struct_mutex to
avoid recursion. Moving the cleanup to a separate task, defers acquiring
the struct_mutex to after the GPU is running again, allowing it to
complete. Even in a few patches time (optimist!) when we no longer
require struct_mutex to unpin the framebuffers, it will still be good
practice to minimise the number of contention points along reset. The
mutex dependency still exists (as one modeset flushes the other), but in
the short term it resolves the deadlock for simple reset cases.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101600
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180623103951.23889-1-chris@chris-wilson.co.uk
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Make ioctl wrappers for functions that will be used by the in-kernel API.
The following functions are touched:
- drm_mode_create_dumb_ioctl()
- drm_mode_destroy_dumb_ioctl()
- drm_mode_addfb()
- drm_mode_rmfb()
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618141739.48151-4-noralf@tronnes.org
|
|
It only makes sense for userspace clients.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618141739.48151-3-noralf@tronnes.org
|
|
Rather than doing drm_file allocation/destruction right in the fops, lets
provide separate helpers. This decouples drm_file management from the
still-mandatory drm-fops. It prepares for use of drm_file without the
fops, both by possible separate fops implementations and APIs (not that I
am aware of any such plans), and more importantly from in-kernel use where
no real file is available.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618141739.48151-2-noralf@tronnes.org
|
|
Some functions are unused after removal of the kmap_atomic
DMA-buf interface.
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: f664a5269542 ("dma-buf: remove kmap_atomic interface")
Link: https://patchwork.freedesktop.org/series/45245/
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
Jernej Skrabec
Shirish S
James Zhu
Leo Liu
David Lechner
Chris Wilson
Daniel Stone
stu.hsieh@mediatek.com
CK Hu
Fabio Estevam
Imre Deak
Sandy Huang
Ville Syrjälä
José Roberto de Souza
Dhinakaran Pandiyan
Rodrigo Vivi
Gustavo A. R. Silva
Christophe JAILLET
Thomas Zimmermann
Maxime Ripard
John Stultz
Noralf Trønnes
David Herrmann
Christian König