| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Runtime suspends disabled all interrupts, so in order to get them back
fully we need to also do the HPD irq setup on runtime resume. Except
on VLV/CHV where the display interrupt initialization is part of the
display power well powerup.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
On SKL the port A HPD has moved to the PCH. Hook it up.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Wire up the port A HPD for BDW. Compared to earlier platforms the
interrupt setup is a bit different, but basically everything else
looks the same.
v2: 0 initialize pin_mask/long_mask due to intel_get_hpd_pins() changes
Check for BDW before processing the HPD to not break BXT
Set found=true when processing port A HPD
Sort out the mess I made of the irq setup in v1
Warn about bad irq mask vs. enable bits in bdw_update_port_irq() (Paulo)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
If the CPU and PCH are on the same package we must enabled the port A
HPD also in the south hotplug register. To identify the package type
we simply look at the PCH type: LPT-H means separate package, and
LPT-LP means multi chip package (MCP).
v2: Add comment and pimp commit message
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
As with ILK/SNB wire up the port A HPD on IVB/HSW.
This might be more important on HSW with PSR. BSpec tells us that if the
automagic link training performed by the hardware fails for some reason,
we're going to get a short HPD and are supposed to re-train the link
manyally.
v2: 0 initialize pin_mask/long_mask due to intel_get_hpd_pins() changes
Add a comment about the pulse duration bits being reserved on HSW+
like we have for LPT+ in ibx_hpd_irq_setup()
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
ILK/SNB support port A HPD. While HPD is optional on eDP let's at least
try to wite it up so that we might notice if the link has issues.
The eDP spec suggests that if HPD is not wired up, one should poll the
link status instead. We don't even do that currently.
v2: 0 initialize pin_mask/long_mask due to intel_get_hpd_pins() changes
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Starting from SPT the only interrupts living in the south are GMBUS and
HPD. What's worse some of the SPT specific new bits conflict with some
other bits on earlier PCH generations. So better not use the
cpt_irq_handler() for SPT+ anymore.
Also kill the hand rolled port E handling with something more
standardish. This also avoids accidentally confusing port B and port E
long pulses since the bits occupy the same positions, just in different
registers.
Also add a comment noting that the short pulse duration bits are
reserved on LPT+. The 2ms value we program is 0, so no issue wrt. the
MBZ in the spec.
v2: Call intel_hpd_irq_handler() only once (Paulo)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Move the 0 initialization of pin_mask and long_mask from
intel_get_hpd_pins() into each caller. This we we can call
intel_get_hpd_pins() multiple times to accumulate more pins from several
sources.
v2: Add a comment explaining the dangers of intel_get_hpd_pins() (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The PORTA HPD defines are not BXT specific. They also exist on SPT,
and partially already on LPT:LP.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Make LPT:LP checks look neater by wrapping the details in a
new HAS_PCH_LPT_LP() macro.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Extract the core of ironlake_{enable,disable}_display_irq() into a new
function. We'll have further use for it later.
v2: Warn about invalid mask vs. enable bits (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Eliminate a bunch of duplicated code that calculates the currently
enabled HPD interrupt bits.
v2: s/;/:/ in patch subject (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Indent the PORTx_HOTPLUG_... defines appropriately, and fix some space
vs. tab issues.
v2: Document pre-HSW/LPT bits, and order another tab (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Forgot to do that in
commit d328c9d78d64ca11e744fe227096990430a88477
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Apr 10 16:22:37 2015 +0200
drm/i915: Select starting pipe bpp irrespective or the primary plane
and it's confusing. Fix it.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
Looking other drm drivers, there is no the restriction that framebuffer
has only one buffer in .create_handle() callback. They use just first
buffer.
If this limitation is removed, there is no reason keeping buffer count
for framebuffer, so we can remove buf_cnt from struct exynos_drm_fb.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
We can get buffer count of framebuffer using drm_format_num_planes(), so
keeping exynos_drm_fb_get_buf_cnt() is unnecessary.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Using exynos_drm_framebuffer_init(), redundant codes can be removed.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This modifies exynos_drm_framebuffer_init() to be possible to support
multiple buffers. Then it can be used by exynos_user_fb_create().
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Current codes get first gem object and then again get remain gem
objects. They can be unified to one routine.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch moves codes to update fb_info into exynos_drm_fbdev_update(),
so fb_info is updated via only one function.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
It can get exynos_gem object via function argument, so no need to call
exynos_drm_fb_gem_obj() in exynos_drm_fbdev_update.
It also can get struct drm_framebuffer *fb via helper->fb, so can remove
a function argument for it.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The variable name "exynos_gem_obj" is too long, so some lines exceed 80
characters. It's simple to use "obj" instead of "exynos_gem_obj".
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The exynos_drm_fb_set_buf_cnt() is used to set buffer count only in
exynos_drm_fbdev_update(). This patch sets directly buffer count in
exynos_drm_framebuffer_init() without using exynos_drm_fb_set_buf_cnt(),
so there is no any reason to keep exynos_drm_fb_set_buf_cnt().
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The cases of the switch statement ensure that reg_type
can never be REG_TYPE_NONE here.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The size check was incomplete. It only computed the
size of area of the drawing rectangle and checked if
the size still fit inside the buffer.
The correct check is to compute the position of the
last byte that the G2D engine is going to access and
then check if that position is still contained in the
buffer. In particular we need the stride information
to determine this.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Pass the correct hpd[] array to intel_get_hpd_pins() on pre-g4x
platforms.
This got broken in the following commit:
commit fd63e2a972c670887e5e8a08440111d3812c0996
Author: Imre Deak <imre.deak@intel.com>
Date: Tue Jul 21 15:32:44 2015 -0700
drm/i915: combine i9xx_get_hpd_pins and pch_get_hpd_pins
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Egbert Eich <eich@suse.de>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
There have been many hard to track down bugs whereby userspace forgot to
flag a write buffer and then cause graphics corruption or a hung GPU
when that buffer was later purged under memory pressure (as the buffer
appeared clean, its pages would have been evicted rather than preserved
and any changes more recent than in the backing storage would be lost).
In retrospect this is a rare optimisation against memory pressure,
already the slow path. If we always mark the buffer as dirty when
accessed by the GPU, anything not used can still be evicted cheaply
(ideal behaviour for mark-and-sweep eviction) but we do not run the risk
of corruption. For correct read serialisation, userspace still has to
notify when the GPU writes to an object. However, there are certain
situations under which userspace may wish to tell white lies to the
kernel...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Kristian Høgsberg <krh@bitplanet.net>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: "Goel, Akash" <akash.goel@intel.co>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
To help with debugging i2c-over-aux issues, add a module parameter than
can be used to tweak the assumed i2c bus speed, and thus the maximum
number of retries we will do for each aux message.
Cc: Simon Farnsworth <simon.farnsworth@onelan.com>
Cc: moosotc@gmail.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Simon Farnsworth <simon.farnsworth@onelan.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Calculate the number of retries we should do for each i2c-over-aux
message based on the time it takes to perform the i2c transfer vs. the
aux transfer. We assume the shortest possible length for the aux
transfer, and the longest possible (exluding clock stretching) for the
i2c transfer.
The DP spec has some examples on how to calculate this, but we don't
calculate things quite the same way. The spec doesn't account for the
retry interval (assumes immediate retry on defer), and doesn't assume
the best/worst case behaviour as we do.
Note that currently we assume 10 kHz speed for the i2c bus. Some real
world devices (eg. some Apple DP->VGA dongle) fails with less than 16
retries. and that would correspond to something close to 15 kHz (with
our method of calculating things) But let's just go for 10 kHz to be
on the safe side. Ideally we should query/set the i2c bus speed via
DPCD but for now this should at leaast remove the regression from the
1->16 byte trasnfer size change. And of course if the sink completes
the transfer quicker this shouldn't slow things down since we don't
change the interval between retries.
I did a few experiments with a DP->DVI dongle I have that allows you
to change the i2c bus speed. Here are the results of me changing the
actual bus speed and the assumed bus speed and seeing when we start
to fail the operation:
actual i2c khz assumed i2c khz max retries
1 1 ok -> 2 fail 211 ok -> 106 fail
5 8 ok -> 9 fail 27 ok -> 24 fail
10 17 ok -> 18 fail 13 ok -> 12 fail
100 210 ok -> 211 fail 2 ok -> 1 fail
So based on that we have a fairly decent safety margin baked into
the formula to calculate the max number of retries.
Fixes a regression with some DP dongles from:
commit 1d002fa720738bcd0bddb9178e9ea0773288e1dd
Author: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Date: Tue Feb 10 18:38:08 2015 +0000
drm/dp: Use large transactions for I2C over AUX
v2: Use best case for AUX and worst case for i2c (Simon Farnsworth)
Add a define our AUX retry interval and account for it
v3: Make everything usecs to avoid confusion about units (Daniel)
Add a comment reminding people about the AUX bitrate (Daniel)
Use DIV_ROUND_UP() since we're after the "worst" case for i2c
Cc: Simon Farnsworth <simon.farnsworth@onelan.com>
Cc: moosotc@gmail.com
Tested-by: moosotc@gmail.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91451
Reviewed-by: Simon Farnsworth <simon.farnsworth@onelan.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Currently we react to native and i2c defers by waiting either 400-500 us
or 500-600 us, depending on which code path we take. Consolidate them
all to one define AUX_RETRY_INTERVAL which defines the minimum interval.
Since we've been using two different intervals pick the longer of them
and define AUX_RETRY_INTERVAL as 500 us. For the maximum just use
AUX_RETRY_INTERVAL+100 us.
I want to have a define for this so that I can use it when calculating
the estimated duration of i2c-over-aux transfers. Without a define it
would be very easy to change the sleep duration and neglect to update
the i2c-over-aux estimates.
Cc: Simon Farnsworth <simon.farnsworth@onelan.com>
Cc: moosotc@gmail.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Simon Farnsworth <simon.farnsworth@onelan.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Backmerge -fixes since there's more DDI-E related cleanups on top of
the pile of -fixes for skl that just landed for 4.3.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i914/intel_dp.c
drivers/gpu/drm/i915/intel_lrc.c
Conflicts are all fairly harmless adjacent line stuff.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
This makes the error message slightly more useful.
Changes since v1:
- Use ktime_get() while irqs are still disabled. (vsyrjala)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
There's already a per crtc member that can be used for it.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
When i915 drivers run inside a VM with Intel GVT-g, some explicit
notifications are needed from guest to host device model through PV
INFO page write. The notifications include:
PPGTT create
PPGTT destroy
They are used for the shadow implementation of PPGTT. Intel GVT-g
needs to write-protect the guest pages of PPGTT, and clear the write
protection when they end their life cycle.
v2:
- Use lower_32_bits()/upper_32_bits() for qword operations;
- Remove the notification of guest context creation/destroy;
Signed-off-by: Zhiyuan Lv <zhiyuan.lv@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Some more definitions in the PV info page are added. They are mainly
for the guest notification to Intel GVT-g device model. They are used
for Broadwell enabling.
The notification of PPGTT page table creation/destroy is to notify
GVT-g device model the life cycle of guest page tables. Then device
model will implement shadow page table for guests.
The notification of context create/destroy is optional. If it is used,
the device model will create/destroy shadow context corresponding to
the context's life cycle. Guest driver needs to make sure that the
context's LRCA and backing storage address unchanged. If it is not
used, the device model will perform the context shadow work in the
context scheduling time.
Signed-off-by: Zhiyuan Lv <zhiyuan.lv@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Broadwell hardware supports both ring buffer mode and execlist mode.
When i915 runs inside a VM with Intel GVT-g, we allow execlist mode
only.
The main reason of EXECLIST only is that GVT-g does not support the
dynamic mode switch between ring buffer mode and execlist mode when
running multiple virtual machines.
v2:
- Adjust the position of vgpu check in sanitize function (Joonas)
- Add vgpu error check in context initialization. (Joonas, Daniel)
Signed-off-by: Zhiyuan Lv <zhiyuan.lv@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This is based on Mika Kuoppala's patch below:
http://article.gmane.org/gmane.comp.freedesktop.xorg.drivers.intel/61104/match=workaround+hw+preload
The patch will preallocate the page directories for 32-bit PPGTT when
i915 runs inside a virtual machine with Intel GVT-g. With this change,
the root pointers in EXECLIST context will always keep the same.
The change is needed for vGPU because Intel GVT-g will do page table
shadowing, and needs to track all the page table changes from guest
i915 driver. However, if guest PPGTT is modified through GPU commands
like LRI, it is not possible to trap the operations in the right time,
so it will be hard to make shadow PPGTT to work correctly.
Shadow PPGTT could be much simpler with this change. Meanwhile
hypervisor could simply prohibit any attempt of PPGTT modification
through GPU command for security.
The function gen8_preallocate_top_level_pdps() in the patch is from
Mika, with only one change to set "used_pdpes" to avoid duplicated
allocation later.
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Zhiyuan Lv <zhiyuan.lv@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
When the audio codec is enabled or disabled, notify the audio driver.
This will enable the audio driver to get the notification at all times
(even when audio is in different powersave states).
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add a common function to return "yes" or "no" string based on the
argument, and drop the local versions of it.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Make it available outside of intel_dp.c.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
If rc6 is enabled, notify GuC so it can do proper forcewake before
command submission.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The firmware layout changes that now it only has css header +
uCode + RSA signature. Plus, other trivial changes to support
GuC V4.3.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The driver doesn't support UMS any more, so set DRIVER_MODESET by default,
remove the legacy s/r callbacks, and rename the s/r functions to make it more clear
they're only in use by switcheroo now.
Also remove an obsolete comment about atomic. Normal updates are supported only
async updates aren't yet.
v2: Don't unconditionally set DRIVER_ATOMIC, we're not yet there.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree for 4.3 (kerneldoc updates, printk()
fixes, Documentation and MAINTAINERS updates)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
MAINTAINERS: update my e-mail address
mod_devicetable: add space before */
scsi: a100u2w: trivial typo in printk
i2c: Fix typo in i2c-bfin-twi.c
treewide: fix typos in comment blocks
Doc: fix trivial typo in SubmittingPatches
proportions: Spelling s/consitent/consistent/
dm: Spelling s/consitent/consistent/
aic7xxx: Fix typo in error message
pcmcia: Fix typo in locking documentation
scsi/arcmsr: Fix typos in error log
drm/nouveau/gr: Fix typo in nv10.c
[SCSI] Fix printk typos in drivers/scsi
staging: comedi: Grammar s/Enable support a/Enable support for a/
Btrfs: Spelling s/consitent/consistent/
README: GTK+ is a acronym
ASoC: omap: Fix typo in config option description
mm: tlb.c: Fix error message
ntfs: super.c: Fix error log
fix typo in Documentation/SubmittingPatches
...
|
|
Make the code mode readable by pulling the "does this crtc have any
encoders?" deduction into a separate function.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The BIOS sometimes likes to enable pipes w/o any ports, at least on
older machines. Currently we fail to assign anything sensible to
crtc->hwmode.crtc_clock which leads to complaints from the vblank code.
Deal with active pipes w/o ports and assign something sensible to
crtc_clock in i9xx_get_pipe_config(). The encoder .get_config() will
override this if the port is enabled.
Gets rid of rest of these on my gen4:
[drm:drm_calc_timestamping_constants [drm]] *ERROR* crtc 24: Can't calculate constants, dotclock = 0!
[drm:i915_get_vblank_timestamp] crtc 1 is disabled
v2: Fill out crtc_clock already in i9xx_get_pipe_config() (Maarten)
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
At various points when changing the DPIO lane/phy power states,
construct an expected value of the DISPLAY_PHY_STATUS register
and compare it with the real thing.
To construct the expected value we look at our shadow PHY_CONTROL
register value (which should match what we've just written to the
hardware), and we also need to look at the actual state of the cmn
power wells as a disabled power well causes the relevant LDO status
to be reported as 'on' in DISPLAY_PHY_STATUS.
When initially powering up the PHY it performs various internal
calibrations for which it fully powers up. That means that if we check
for the expetected power state immediately upon releasing cmnreset we
would get the occasional false positive. But we can of course
poll until the expected value appears. It shouldn't be too long so
this shouldn't make modesets substantially longer.
One extra complication is introduced when we cross the streams, ie.
drive port B with pipe B. In this case we trick CL2 (where the DPLL lives)
into life by temporaily powering up the lanes in the second channel,
and once the pipe is up and runnign we release the lane power override.
At that point the power state of CL2 has somehow gotten entangled with
the power state of the first channel. That means that constructing the
expected DISPLAY_PHY_STATUS value is a bit tricky since based on the
lane power states in the second channel, CL2 should also be powered
down. But we can use the DPLL enable bit to determine when CL2 should
be alive even if the lanes are powered down. However the power state
of CL2 isn't actually tied in with the DPLL state, but to the state
of the lanes in first channel, so we have to avoid checking the
expected state between shutting down the DPLL and powering down
the lanes in the first channel. So no calling assert_chv_phy_status()
before the DISPLAY_PHY_CONTROL write in chv_phy_powergate_lanes(),
but after the write is a safe time to check.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Add some checks that the state of the DPIO lanes is more or less what we
expect based on the overrides.
The hardware only provides two bits per channel indicating whether all
or some of the lanes are powered down, so we can't do an exact check.
Additionally, CL2 powering down before we can check it adds another
twist. To work around this we simply check for the 0 value of the
CL2 register (which is what we get when it's powered down) and
adjust our expectations.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Currently we release the lane soft reset before lane stagger settings
have been programmed. I believe that means we don't actually do lane
staggering. So move the soft reset deassert to happen after lane
staggering has been programmed.
The one confusing thing in this is that when we remove the power down
override from the lanes, they power up with defaul register values,
which do not have the soft reset overrides enabled. And according to
some docs by default the data lane resets are tied to cmnreset. So that
would mean that lanes would come out of reset without staggering as
soon as the power down overrides are removed. But since we can't access
either the lane stagger register nor the soft reset override registers
until the lanes are powered on, we can't really do anything about it.
So let's just set the soft reset overrides as soon as the lane is
powered on and hope for the best.
v2: Fix typos in commit message (Daniel)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The DP MST encoder config function never sets ddi_pll_sel, even though
its value is programmed in its ->pre_enable() hook. That used to work
because a new pipe_config was kzalloc'ed at every modeset, and the value
of zero selects the highest clock for the PLL. Starting with the commit
below, the value of ddi_pll_sel is preserved through modesets, and since
the correct value wasn't properly setup by the MST code, it could lead
to warnings and blank screens.
commit 8504c74c7ae48b4b8ed1f1c0acf67482a7f45c93
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Fri May 15 11:51:50 2015 +0300
drm/i915: Preserve ddi_pll_sel when allocating new pipe_config
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91628
Cc: stable@vger.kernel.org # 7e6313a2516d drm/i915: Don't use link_bw for PLL setup
Cc: stable@vger.kernel.org
Cc: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
Ville Syrjälä
Daniel Vetter
Joonyoung Shim
Tobias Jakobi
Chris Wilson
Maarten Lankhorst
Zhiyuan Lv
David Henningsson
Jani Nikula
Alex Dai
Linus Torvalds
Ander Conselvan de Oliveira