| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
According to bspec the DDI PHY vswing scale value is "don't care" in
case the scale enable bit [27] is clear. But this doesn't seem to be
correct. The scale value seems to also matter if the scale mode bit
[26] is set. So both bit 26 and 27 depend on the value. Setting the
scale value to 0 while either bit is set results in a failed modeset on
HDMI (sink reports no signal).
After reset the scale value is 0x98, but according to the spec we have
to program it to 0x9a. So for consistency program it always to 0x9a
regardless of the scale enable bit.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Matt Roper <matthew.d.roper@intel.com>
Acked-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Ville's and Mika's cdclk series was in flight at the same time as the
SKL S3 patches so we were missing that update.
intel_update_max_cdclk() and intel_update_cdclk() had to be moved up a
bit to avoid forward declarations.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
intel_update_cdclk() will already display the boot CDCLK for DDI
platforms, no need to repeat there.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
We can operate with DPLL0 off with CDCLK backed by the 24Mhz reference
clock, and that's a supported configuration. Don't warn when notice
DPLL0 is off then.
We still have a separate warn at boot if cdclk is disabled (because we
don't currently try to handle the case (that shouldn't happen on SKL as
far as I know) where we boot with display not initialized.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Add support for changing cdclk frequency during runtime on BDW.
Also with IPS enabled the actual pixel rate mustn't exceed 95% of cdclk,
so take that into account when computing the max pixel rate.
v2: Grab rps.hw_lock around sandybridge_pcode_write()
v3: Rebase due to power well vs. .global_resources() reordering
v4: Rebased to the latest
v5: Rebased to the latest
v6: Patch order shuffle so that Broadwell CD clock change is
applied before the patch for Haswell CD clock change
v7: Fix for patch style problems
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
We need to tell BDW ULT and ULX apart.
v2: Rebased to the latest
v3: Rebased to the latest
v4: Fix for patch style problems
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Bspec says we shouldn't enable IPS on BDW when the pipe pixel rate
exceeds 95% of the core display clock. Apparently this can cause
underruns.
There's no similar restriction listed for HSW, so leave that one alone
for now.
v2: Add pipe_config_supports_ips() (Chris)
v3: Compare against the max cdclk insted of the current cdclk
v4: Rebased to the latest
v5: Rebased to the latest
v6: Fix for patch style problems
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=83497
Tested-by: Timo Aaltonen <tjaalton@ubuntu.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Keep the cdclk maximum supported frequency around in dev_priv so that we
can verify certain things against it before actually changing the cdclk
frequency.
For now only VLV/CHV have support changing cdclk frequency, so other
plarforms get to assume cdclk is fixed.
v2: Rebased to the latest
v3: Rebased to the latest
v4: Fix for patch style problems
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Rather than reading out the current cdclk value use the cached value we
have tucked away in dev_priv.
v2: Rebased to the latest
v3: Rebased to the latest
v4: Fix for patch style problems
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Rather that extracting the current cdclk freuqncy every time someone
wants to know it, cache the current value and use that. VLV/CHV already
stored a cached value there so just expand that to cover all platforms.
v2: Rebased to the latest
v3: Rebased to the latest
v4: Rebased to the latest
v5: Removed spurious call to 'intel_update_cdclk(dev)' based on
Damien Lespiau's comment
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Main pull req for 4.2.. I think there will be a secondary pull-req..
I'd like to land the hdcp support patches, since all the review
comments have been long since addressed, and they have been ready to
merge for a couple release cycles now other than the scm dependency
(which should be coming in through arm-soc tree for 4.2). So I am not
including them in this initial pull req to avoid merge ordering
issues.
Main highlights:
1) adreno a306 support (for apq8x16 and upcoming dragonboard 410c)
2) various dsi bits
3) various 64bit fixes (mostly warnings)
4) NV12MT support, pulled in via msm-next rather than drm-misc since
dependency on on regenerated envytools headers (but lgtm'd-by danvet)
5) random fixes and cleanups
* 'msm-next' of git://people.freedesktop.org/~robclark/linux: (36 commits)
drm/msm: restart queued submits after hang
drm/msm: fix timeout calculation
drm/msm/hdmi: Use pinctrl in HDMI driver
drm/msm/hdmi: Point to the right struct device
drm/msm/mdp: Add support for more 32-bit RGB formats
drm/msm: use __s32, __s64, __u32 and __u64 from linux/types.h for uabi
drm/msm/atomic: Clean up planes in the error paths of .atomic_commit()
drm/msm/mdp5: Always generate active-high sync signals for DSI
drm/msm: dsi: fix compile errors when CONFIG_GPIOLIB=n
drm/msm: use devm_gpiod_get_optional for optional reset gpio
drm/msm/dsi: Separate PHY to another platform device
drm/msm/dsi: Enable PLL driver in MSM DSI
drm/msm/dsi: Add DSI PLL clock driver support
drm/msm: use IS_ERR() to check regulator_get() return
drm/msm: use IS_ERR() to check msm_ioremap() return
drm/msm/mdp5: Wait for PP_DONE irq for command mode CRTC atomic commit
drm/msm: Use customized function to wait for atomic commit done
dt-bindings: Add MSM eDP controller documentation
dt-bindings: Add MSM DSI controller documentation
drm/msm: drop redundant debug output
...
|
|
firmware name fix
* tag 'drm-intel-next-fixes-2015-06-11' of git://anongit.freedesktop.org/drm-intel:
drm/i915/skl: Fix DMC API version in firmware file name
|
|
- Make the reset wavefronts action be per process per device instead of
per process, because one device can be stuck but the other one won't be
- Add some missing properties to the CZ device_info structure
- Rename symbols to not have CONFIG_ prefix
- Some more cleanups and debug prints
* tag 'drm-amdkfd-next-fixes-2015-06-10' of git://people.freedesktop.org/~gabbayo/linux:
drm/amdkfd: remove not used defines from cik_regs.h
drm/amdkfd: Add missing properties to CZ device info
drm/amdkfd: make reset wavefronts per process per device
drm/amdkfd: add debug print to kfd_events.c
drm/amdkfd: avoid CONFIG_ prefix for non-Kconfig symbols
|
|
Mainly it is fixing timing on HDMI to be compliant with CEA-861E spec.
* '2015-06-08-st-drm-next' of http://git.linaro.org/people/benjamin.gaignard/kernel:
drm/sti: vtg fix CEA-861E video format timing error
drm/sti: hdmi fix CEA-861E video format timing error
drm/sti: VTG interrupt names are badly displayed
drm/sti: missing first pixel column on HDMI display
drm/sti: correctly test devm_ioremap() return
|
|
Fix for the regression Linus called out, and another for probing
dongles.
* tag 'drm-intel-fixes-2015-06-11' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Fix DDC probe for passive adapters
drm/i915: Properly initialize SDVO analog connectors
|
|
Track the list of in-flight submits. If the gpu hangs, retire up to an
including the offending submit, and then re-submit the remainder. This
way, for concurrently running piglit tests (for example), one failing
test doesn't cause unrelated tests to fail simply because it's submit
was queued up after one that triggered a hang.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
The 'timeout' value comes from userspace (CLOCK_MONOTONIC), but
converting this directly to jiffies doesn't take into account the
initial jiffies count at boot, which may differ from the base time
of CLOCK_MONOTONIC.
TODO: add ktime_delta_jiffies() when rebasing on 4.1 and use that
instead of ktime_sub/ktime_to_timespec/timespec_to_jiffies combo (as
suggested by Arnd)
v2: switch over from 'struct timespec' to ktime_t throughout, since
'struct timespec' will be deprecated (as suggested by Arnd)
v3: minor cosmetic tweaks
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Some targets (eg: msm8994) use the pinctrl framework to configure
interface pins. This change adds support for initialization and
pinctrl active/sleep state control for the HDMI driver.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
DRM device's dev (hdmi->dev->dev) points to the mdss_mdp device
handle. Instead, we should get a reference to the mdss_hdmi
handle.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
That will complete the lists of Alpha + RGB formats.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
When the .atomic_commit() handler fails, clean up planes previoulsy
prepared by drm_atomic_helper_prepare_planes() with a call to
drm_atomic_helper_cleanup_planes().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
DSI video mode engine can only take active-high sync signals. This
change prevents MDP5 sending active-low sync signals to DSI in any
case.
Signed-off-by: Hai Li <hali@codeaurora.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
I'm not sure where, exactly, but somewhere in here we must be relying on
an implicit include.
drivers/gpu/drm/msm/dsi/dsi_host.c: In function ‘dsi_host_init_panel_gpios’:
drivers/gpu/drm/msm/dsi/dsi_host.c:1356:2: error: implicit declaration of function ‘devm_gpiod_get’ [-Werror=implicit-function-declaration]
msm_host->disp_en_gpio = devm_gpiod_get(panel_device,
^
drivers/gpu/drm/msm/dsi/dsi_host.c:1356:25: warning: assignment makes pointer from integer without a cast [enabled by default]
msm_host->disp_en_gpio = devm_gpiod_get(panel_device,
^
drivers/gpu/drm/msm/dsi/dsi_host.c:1364:3: error: implicit declaration of function ‘gpiod_direction_output’ [-Werror=implicit-function-declaration]
ret = gpiod_direction_output(msm_host->disp_en_gpio, 0);
^
drivers/gpu/drm/msm/dsi/dsi_host.c:1371:20: warning: assignment makes pointer from integer without a cast [enabled by default]
msm_host->te_gpio = devm_gpiod_get(panel_device, "disp-te");
^
drivers/gpu/drm/msm/dsi/dsi_host.c:1378:3: error: implicit declaration of function ‘gpiod_direction_input’ [-Werror=implicit-function-declaration]
ret = gpiod_direction_input(msm_host->te_gpio);
^
drivers/gpu/drm/msm/dsi/dsi_host.c: In function ‘msm_dsi_host_power_on’:
drivers/gpu/drm/msm/dsi/dsi_host.c:1918:3: error: implicit declaration of function ‘gpiod_set_value’ [-Werror=implicit-function-declaration]
gpiod_set_value(msm_host->disp_en_gpio, 1);
^
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Hai Li <hali@codeaurora.org>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Since 39b2bbe3d715 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Also there is a variant to find optional gpios that returns NULL if
there is no gpio instead of -ENOENT.
Make use of both features to simplify the driver.
This makes error checking more strict because errors like -ENOSYS ("no
gpio support compiled in") or -EPROBE_DEFER ("gpio not ready yet") are
handled correctly now.
Furthermore this is one caller less that stops us making the flags
argument to gpiod_get*() mandatory.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
There are different types of PHY from one chipset to another, while
the DSI host controller is relatively consistent across platforms.
Also, the PLL inside PHY is providing the source of DSI byte and
pixel clocks, which are used by DSI host controller. Separated devices
for clock provider and clock consumer make DSI driver better fit into
common clock framework.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
This change activates PLL driver for DSI to work with
common clock framework.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
DSI byte clock and pixel clocks are sourced from DSI PLL.
This change adds the DSI PLL source clock driver under
common clock framework.
This change handles DSI 28nm PLL only.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
regulator_get() never returns NULL. There's no need for IS_ERR_OR_NULL()
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
msm_ioremap() never returns NULL. There's no need for IS_ERR_OR_NULL()
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
CRTCs in DSI command mode data path should wait for pingpong done,
instead of vblank, to finish atomic commit.
This change is to enable PP_DONE irq on command mode CRTCs and wait for
this irq happens before atomic commit completion.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
MDP FLUSH registers could indicate if the previous flush updates
has taken effect at vsync boundary. Making use of this H/W feature
can catch the vsync that happened between CRTC atomic_flush and
*_wait_for_vblanks, to avoid unnecessary wait.
This change allows kms CRTCs to use their own *_wait_for_commit_done
functions to wait for FLUSH register cleared at vsync, before commit
completion.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
wait_for_completion_timeout returns 0 in case of timeout and never
return < 0 so there is no additional information in printing the
value of time_left here as it will always be 0, thus it can be dropped.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
wait_for_completion_timeout returns >= 0 but never
negative - so the error check should be against equality
to 0 not <= 0.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
return type of wait_for_completion_timeout is unsigned long not int, this
patch assigns the return value of wait_for_completion_timeout to an
appropriately typed and named variable.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Some DSI peripherals rely on the HS clock on DSI clock lane as their clock
source. If the clock lane transitions between HS and LP states, it
can disrupt the functioning of such peripherals.
The mipi dsi mode flag MIPI_DSI_CLOCK_NON_CONTINUOUS already exists for
such peripheral drivers. Use it to configure the bit CLKLN_HS_FORCE_REQUEST
in DSI_LANE_CTRL.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
If the GEM object is imported, drm_prime_gem_destroy needs to be
called to clean up dma buffer related information.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Fix build warning when building edp/edp_aux.o due to missing
prototype for edp_aux_transfer.
This function is only used in edp_aux.c so just make it static.
Reported-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
wait_for_completion_timeout returns 0 in case of timeout so printing the
return value here will always yield 0 and is therefor redundant - dropped.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
The timeout is passed as a constant which makes it HZ dependent because
jiffies are expected so it should be converted to jiffies. The actual
value is not clear from the code - my best guess is that this should be
300 milliseconds given that other timeouts are in milliseconds based on
looking at other drm drivers (e.g. exynos_drm_dsi.c:356 300ms,
tegra/dpaux.c:188 250ms) - this needs to be confirmed by someone who
knows the details of the driver.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
wait_for_completion_timeout return >= 0 but never negative so the check
logic looks inconsistent. Further the return value of
wait_for_completion_timeout was being passed up the call chain but the
x call sites as drm_dp_i2c_do_msg()/drm_dp_dpcd_access() check for < 0
thus timeout was being treated as success case.
<snip> drivers/gpu/drm/drm_dp_helper.c:drm_dp_i2c_do_msg()
mutex_lock(&aux->hw_mutex);
ret = aux->transfer(aux, msg);
mutex_unlock(&aux->hw_mutex);
if (ret < 0) {
<snip>
logic in edp_aux_transfer() seems incorrect as it could return 0 (timeout)
but checks of <= 0 to indicate error so the return probably should be
-ETIMEDOUT in case wait_for_completion_timeout returns 0 (timeout
occurred).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Seems like disable can race with complete_flip() in process of disabling
a crtc, leading to:
[ 49.065364] Call trace:
[ 49.071441] [<ffffffc00041d5a0>] mdp5_ctl_blend+0x20/0x1c0
[ 49.073788] [<ffffffc00041ebcc>] mdp5_crtc_disable+0x3c/0xa8
[ 49.079348] [<ffffffc0003e7854>] disable_outputs.isra.4+0x11c/0x220
[ 49.085164] [<ffffffc0003e7afc>] drm_atomic_helper_commit_modeset_disables+0x14/0x38
[ 49.091155] [<ffffffc000425c80>] complete_commit+0x40/0xb8
[ 49.099136] [<ffffffc0004260ac>] msm_atomic_commit+0x364/0x398
[ 49.104430] [<ffffffc00040a614>] drm_atomic_commit+0x3c/0x70
[ 49.110249] [<ffffffc0003e67b8>] drm_atomic_helper_set_config+0x1b0/0x3e0
[ 49.116065] [<ffffffc0003f99bc>] drm_mode_set_config_internal+0x64/0xf8
[ 49.122746] [<ffffffc0003fa624>] drm_framebuffer_remove+0xe4/0x128
[ 49.129171] [<ffffffc0003feaf8>] drm_mode_rmfb+0xc0/0x100
[ 49.135420] [<ffffffc0003efba8>] drm_ioctl+0x258/0x4d0
[ 49.140889] [<ffffffc0001b0388>] do_vfs_ioctl+0x338/0x5d0
[ 49.145921] [<ffffffc0001b06a8>] SyS_ioctl+0x88/0xa0
It makes no sense to free the ctl without disabling all stages, so lets
just move them together to avoid the crash.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
As found in apq8016 (used in DragonBoard 410c) and msm8916.
Note that numerically a306 is actually 307 (since a305c already claimed
306). Nice and confusing.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
A few spots in the driver have support for downstream android
CONFIG_MSM_BUS_SCALING. This is mainly to simplify backporting the
driver for various devices which do not have sufficient upstream
kernel support. But the intentionally dead code seems to cause
some confusion. Rename the #define to make this more clear.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Using fb modifier flag, support NV12MT format in MDP4.
v2:
- rework the modifier's description [Daniel Vetter's comment]
- drop .set_mode_config() callback [Rob Clark's comment]
v3:
- change VENDOR's name and restrict usage to NV12 [pointed by Daniel]
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
Imre Deak
Damien Lespiau
Ville Syrjälä
Dave Airlie
Rob Clark
Stephane Viau
Laurent Pinchart
Hai Li
Brian Norris
Uwe Kleine-König
Fabian Frederick
Nicholas Mc Guire
Archit Taneja
jilai wang