| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This driver provides an i2c I/O mechanism for the core nct6775 driver,
as might be used by a BMC. Because the Super I/O chip is shared with
the host CPU in such a scenario (and the host should ultimately be in
control of it), the i2c driver is strictly read-only to avoid
interfering with any usage by the host (aside from the bank-select
register, which seems to be replicated for the i2c interface).
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Tested-by: Renze Nicolai <renze@rnplus.nl>
Link: https://lore.kernel.org/r/20220428012707.24921-3-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for the temperatur sensor and the fan controller on the
Microchip LAN966x SoC. Apparently, an Analog Bits PVT sensor is used
which can measure temperature and process voltages. But only a forumlae
for the temperature sensor is known. Additionally, the SoC support a fan
tacho input as well as a PWM signal to control the fan.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220401214032.3738095-5-michael@walle.cc
[groeck: Added missing reference in Documentation/hwmon/index.rst]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This splits the nct6775 driver into an interface-independent core and
a separate platform driver that wraps inb/outb port I/O (or asuswmi
methods) around that core.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Tested-by: Renze Nicolai <renze@rnplus.nl>
Link: https://lore.kernel.org/r/20220427010154.29749-7-zev@bewilderbeest.net
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (556 commits)
firmware: google: Properly state IOMEM dependency
kgdbts: fix return value of __setup handler
firmware: sysfb: fix platform-device leak in error path
firmware: stratix10-svc: add missing callback parameter on RSU
arm64: dts: qcom: add non-secure domain property to fastrpc nodes
misc: fastrpc: Add dma handle implementation
misc: fastrpc: Add fdlist implementation
misc: fastrpc: Add helper function to get list and page
misc: fastrpc: Add support to secure memory map
dt-bindings: misc: add fastrpc domain vmid property
misc: fastrpc: check before loading process to the DSP
misc: fastrpc: add secure domain support
dt-bindings: misc: add property to support non-secure DSP
misc: fastrpc: Add support to get DSP capabilities
misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP
misc: fastrpc: separate fastrpc device from channel context
dt-bindings: nvmem: brcm,nvram: add basic NVMEM cells
dt-bindings: nvmem: make "reg" property optional
nvmem: brcm_nvram: parse NVRAM content into NVMEM cells
nvmem: dt-bindings: Fix the error of dt-bindings check
...
|
|
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for Maxim MAX77714 PMIC
Removed Drivers:
- Remove support for ST-Ericsson AB8500 DebugFS
New Device Support:
- Add support for Silergy SY7636A to Simple MFD I2C
- Add support for MediaTek MT6366 PMIC to MT6358 IRQ
- Add support for Charger to Intel PMIC CRC
- Add support for Raptor Lake to Intel LPSS PCI
New Functionality:
- Add support for Reboot to Rockchip RK808
Fix-ups:
- Device Tree changes (includcing YAML conversion) for
silergy,sy7636a, maxim,max77843, google,cros-ec, maxim,max14577,
maxim,max77802, maxim,max77714, qcom,tcsr, qcom,spmi-pmic,
stericsson,ab8500, stericsson,db8500-prcmu,
samsung,exynos5433-lpass, mt6397, syscon, brcm,cru
- Visible to menuconfig; simple-mfd-i2c
- Clean-up or clarify code; max77686, intel_soc_pmic_crc
- Improve error handling; mc13xxx-core, stmfx, asic3
- Pass device information to child devices; iqs62x, intel-lpss-acpi
- Individually identify IRQ domains; intel_soc_pmic_core
- Remove superfluous code; dbx500-prcmu, exynos-lpass
- Staticify and constify; arizona-i2c
- Mark sometimes used data as __maybe_unused; atmel-flexcom
- Account for different ACPI tables on AOSP/Windows platforms; arizona-spi
- Use provided (platform) APIs; ab8500-core
- Trivial (whitespace, spelling); rohm-bd9576"
* tag 'mfd-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (50 commits)
dt-bindings: mfd: syscon: Add microchip,lan966x-cpu-syscon compatible
mfd: bd9576: fix typos in comments
mfd: Use platform_get_irq() to get the interrupt
mfd: db8500-prcmu: Remove unused inline function
mfd: arizona-spi: Add Android board ACPI table handling
mfd: arizona-spi: Split Windows ACPI init code into its own function
mfd: asic3: Add missing iounmap() on error asic3_mfd_probe
MAINTAINERS: Rectify entry for ROHM MULTIFUNCTION BD9571MWV-M PMIC DEVICE DRIVERS
mfd: intel-lpss: Provide an SSP type to the driver
dt-bindings: mfd: brcm,cru: Rename pinctrl node
dt-bindings: Add compatibles for undocumented trivial syscons
mfd: atmel-flexcom: Fix compilation warning
dt-bindings: mfd: Add compatible for the MediaTek MT6366 PMIC
dt-bindings: mfd: samsung,exynos5433-lpass: Convert to dtschema
mfd: exynos-lpass: Drop unneeded syscon.h include
mfd: intel-lpss: Add Intel Raptor Lake PCH-S PCI IDs
mfd: ab8500: Drop debugfs module
mfd: sta2x11: Use GFP_KERNEL instead of GFP_ATOMIC
mfd: ab8500: Rewrite bindings in YAML
mfd: qcom-spmi-pmic: Add pm8953 compatible
...
|
|
Add support for Texas Instruments TMP464 and TMP468 temperature sensor
ICs.
TI's TMP464 is an I2C temperature sensor chip. This chip is similar
to TI's TMP421 chip, but with 16bit-wide registers (instead of
8bit-wide registers). The chip has one local sensor and four remote
sensors. TMP468 is similar to TMP464 but has one local and eight
remote sensors.
Originally-from: Agathe Porte <agathe.porte@nokia.com>
Cc: Agathe Porte <agathe.porte@nokia.com>
Cc: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Tested-by: Agathe Porte <agathe.porte@nokia.com>
Link: https://lore.kernel.org/r/20220222223610.23098-2-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver provides the same data as the asus_wmi_ec_sensors driver
(and gets it from the same source) but does not use WMI, polling
the ACPI EC directly.
That provides two enhancements: sensor reading became quicker (on some
systems or kernel configuration it took almost a full second to read
all the sensors, that transfers less than 15 bytes of data), the driver
became more flexible. The driver now relies on ACPI mutex to lock access
to the EC in the same way as the WMI code does.
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220124015658.687309-2-eugene.shalygin@gmail.com
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Denis Pauk <pauk.denis@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add peci-cputemp driver for Digital Thermal Sensor (DTS) thermal
readings of the processor package and processor cores that are
accessible via the PECI interface.
The main use case for the driver (and PECI interface) is out-of-band
management, where we're able to obtain the DTS readings from an external
entity connected with PECI, e.g. BMC on server platforms.
Co-developed-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
Link: https://lore.kernel.org/r/20220208153639.255278-11-iwona.winiarska@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is a multi-function device to interface with the sy7636a
EPD PMIC chip from Silergy.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This driver implements monitoring and control of fans plugged into the
device. Besides typical speed monitoring and PWM duty cycle control,
voltage and current are reported for every fan.
The device also has 2 connectors for RGB LEDs, support for them isn't
implemented (mainly because there is no standardized sysfs interface).
Also, the device has a noise sensor, but the sensor seems to be completely
useless (and very imprecise), so support for it isn't implemented too.
The driver coexists with userspace tools that access the device through
hidraw interface with no known issues.
The driver has been tested on x86_64, built in and as a module.
Some changes/improvements were suggested by Jonas Malaco.
Signed-off-by: Aleksandr Mezin <mezin.alexander@gmail.com>
Link: https://lore.kernel.org/r/20211031033058.151014-1-mezin.alexander@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Provides a Linux kernel module "asus_wmi_sensors" that provides sensor
readouts via ASUS' WMI interface present in the UEFI of
X370/X470/B450/X399 Ryzen motherboards.
Supported motherboards:
* ROG CROSSHAIR VI HERO,
* PRIME X399-A,
* PRIME X470-PRO,
* ROG CROSSHAIR VI EXTREME,
* ROG CROSSHAIR VI HERO (WI-FI AC),
* ROG CROSSHAIR VII HERO,
* ROG CROSSHAIR VII HERO (WI-FI),
* ROG STRIX B450-E GAMING,
* ROG STRIX B450-F GAMING,
* ROG STRIX B450-I GAMING,
* ROG STRIX X399-E GAMING,
* ROG STRIX X470-F GAMING,
* ROG STRIX X470-I GAMING,
* ROG ZENITH EXTREME,
* ROG ZENITH EXTREME ALPHA.
Co-developed-by: Ed Brindley <kernel@maidavale.org>
Signed-off-by: Ed Brindley <kernel@maidavale.org>
Signed-off-by: Denis Pauk <pauk.denis@gmail.com>
[groeck: Squashed:
"hwmon: Fix warnings in asus_wmi_sensors.rst documetation."]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Linux HWMON sensors driver for ASUS motherboards to read
sensors from the embedded controller.
Many ASUS motherboards do not publish all the available
sensors via the Super I/O chip but the missing ones are
available through the embedded controller (EC) registers.
This driver implements reading those sensor data via the
WMI method BREC, which is known to be present in all ASUS
motherboards based on the AMD 500 series chipsets (and
probably is available in other models too). The driver
needs to know exact register addresses for the sensors and
thus support for each motherboard has to be added explicitly.
The EC registers do not provide critical values for the
sensors and as such they are not published to the HWMON.
Supported motherboards:
* PRIME X570-PRO
* Pro WS X570-ACE
* ROG CROSSHAIR VIII HERO
* ROG CROSSHAIR VIII DARK HERO
* ROG CROSSHAIR VIII FORMULA
* ROG STRIX X570-E GAMING
* ROG STRIX B550-I GAMING
* ROG STRIX B550-E GAMING
Co-developed-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Co-developed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Denis Pauk <pauk.denis@gmail.com>
Tested-by: Tor Vic <torvic9@mailbox.org>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The INA238 is a I2C power monitor similar to other INA2xx devices,
providing shunt voltage, bus voltage, current, power and temperature
measurements.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Link: https://lore.kernel.org/r/20211102052754.817220-3-nathan@nathanrossi.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add hardware monitoring driver for Maxim MAX6620 Fan controller
Originally-from: L. Grunenberg <contact@lgrunenberg.de>
Originally-from: Cumulus Networks <support@cumulusnetworks.com>
Originally-from: Shuotian Cheng <shuche@microsoft.com>
Signed-off-by: Arun Saravanan Balachandran <Arun_Saravanan_Balac@dell.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver exposes hardware sensors of the Aquacomputer D5 Next
watercooling pump, which communicates through a proprietary USB HID
protocol.
Available sensors are pump and fan speed, power, voltage and current, as
well as coolant temperature. Also available through debugfs are the serial
number, firmware version and power-on count.
Attaching a fan is optional and allows it to be controlled using
temperature curves directly from the pump. If it's not connected,
the fan-related sensors will report zeroes.
The pump can be configured either through software or via its physical
interface. Configuring the pump through this driver is not implemented,
as it seems to require sending it a complete configuration. That
includes addressable RGB LEDs, for which there is no standard sysfs
interface. Thus, that task is better suited for userspace tools.
This driver has been tested on x86_64, both in-kernel and as a module.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Commit 9049572fb145 ("hwmon: Remove amd_energy driver") removes the driver,
but misses to adjust the Makefile.
Hence, ./scripts/checkkconfigsymbols.py warns:
SENSORS_AMD_ENERGY
Referencing files: drivers/hwmon/Makefile
Remove the missing piece of this driver removal.
Fixes: 9049572fb145 ("hwmon: Remove amd_energy driver")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20210817084811.10673-1-lukas.bulwahn@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
On AMD platforms the Out-of-band access is provided by
Advanced Platform Management Link (APML), APML is a
SMBus v2.0 compatible 2-wire processor client interface.
APML is also referred as the sideband interface (SBI).
APML is used to communicate with the
Side-Band Remote Management Interface (SB-RMI) which provides
Soft Mailbox messages to manage power consumption and
power limits of the CPU socket.
- This module add support to read power consumption,
power limit & max power limit and write power limit.
- To instantiate this driver on a Board Management Controller (BMC)
connected to an AMD CPU with SB-RMI support, the i2c bus number
would be the bus connected from the BMC to the CPU.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Akshay Gupta <Akshay.Gupta@amd.com>
Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Link: https://lore.kernel.org/r/20210726133615.9709-1-nchatrad@amd.com
[groeck: Fix uninitialized variable problem when reporting max power]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This patch adds a hwmon driver for the SHT4x Temperature and
Humidity sensor.
Signed-off-by: Navin Sankar Velliangiri <navin@linumiz.com>
[groeck: dropped unnecessary empty line and continuation lines]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
These are "all-in-one" CPU liquid coolers that can be monitored and
controlled through a proprietary USB HID protocol.
While the models have differently sized radiators and come with varying
numbers of fans, they are all indistinguishable at the software level.
The driver exposes fan/pump speeds and coolant temperature through the
standard hwmon sysfs interface.
Fan and pump control, while supported by the devices, are not currently
exposed. The firmware accepts up to 61 trip points per channel
(fan/pump), but the same set of trip temperatures has to be maintained
for both; with pwmX_auto_point_Y_temp attributes, users would need to
maintain this invariant themselves.
Instead, fan and pump control, as well as LED control (which the device
also supports for 9 addressable RGB LEDs on the CPU water block) are
left for existing and already mature user-space tools, which can still
be used alongside the driver, thanks to hidraw. A link to one, which I
also maintain, is provided in the documentation.
The implementation is based on USB traffic analysis. It has been
runtime tested on x86_64, both as a built-in driver and as a module.
Signed-off-by: Jonas Malaco <jonas@protocubo.io>
Link: https://lore.kernel.org/r/20210319045544.416138-1-jonas@protocubo.io
[groeck: Removed unnecessary spinlock.h include]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add basic monitoring support as well as port on/off control for Texas
Instruments TPS23861 PoE PSE IC.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210121134434.2782405-2-robert.marko@sartura.hr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This patch adds a hwmon driver for the AHT10 Temperature and
Humidity sensor. It has a maximum sample rate, as the datasheet
states that the chip may heat up if it is sampled more than once
every two seconds.
Has been tested a to work on a raspberrypi0w
Signed-off-by: Johannes Cornelis Draaijer (datdenkikniet) <jcdra1@gmail.com>
Link: https://lore.kernel.org/r/20210107194014.GA88780@desktop
[groeck: dropped AHT10_ADDR (unused) and use AHT10_MEAS_SIZE where
appropriate; dropped change log]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This deletes the ABx500 hwmon driver, the only supported
variant being the AB8500.
This driver has been replaced by generic frameworks. By
inspecting the abx500 sysfs files we see that it contains
things such as temp1_max, temp1_max_alarm, temp1_max_hyst,
temp1_max_hyst_alarm, temp1_min, temp1_min_alarm.
It becomes obvious that the abx500.c is a reimplementation
of thermal zones. This is not very strange as the generic
thermal zones were not invented when this driver was merged
so people were rolling their own.
The ab8500.c driver contains conversion tables for handling
a thermistor on ADC channels AUX1 and AUX2.
I managed to replace the functionality of the driver with:
- Activation of the ntc_thermistor.c driver,
CONFIG_SENSORS_NTC_THERMISTOR
- Activation of thermal zones, CONFIG_THERMAL
- In the device tree, connecting the NTC driver to the
processed IIO channels from the AB8500 GPADC ADC forming
two instances of NTC sensors.
- Connecting the two NTC sensors to a "chassis" thermal zone
in the device tree and setting that to hit the CPU frequency
at 50 degrees celsius and do a critical shutdown at 70
degrees celsius, deploying a policy using the sensors.
After talking to the original authors we concluded that the
driver was never properly parameterized in production so
what we now have in the device tree is already puts the
thermistors to better use than what the hwmon driver did.
The two remaining channels for two battery temperatures is
already handled in the charging algorithms but can be
optionally extended to thermal zones as well if we want
these to trigger critical shutdown for the platform.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201221125521.768082-1-linus.walleij@linaro.org
[groeck: Removed documentation and fixed up Makefile, Kconfig]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
SB Temperature Sensor Interface (SB-TSI) is an SMBus compatible
interface that reports AMD SoC's Ttcl (normalized temperature),
and resembles a typical 8-pin remote temperature sensor's I2C interface
to BMC.
This commit adds basic support using this interface to read CPU
temperature, and read/write high/low CPU temp thresholds.
To instantiate this driver on an AMD CPU with SB-TSI
support, the i2c bus number would be the bus connected from the board
management controller (BMC) to the CPU. The i2c address is specified in
Section 6.3.1 of the spec [1]: The SB-TSI address is normally 98h for
socket 0 and 90h for socket 1, but it could vary based on hardware address
select pins.
[1]: https://www.amd.com/system/files/TechDocs/56255_OSRR.pdf
Test status: tested reading temp1_input, and reading/writing
temp1_max/min.
Signed-off-by: Kun Yi <kunyi@google.com>
Link: https://lore.kernel.org/r/20201211215427.3281681-2-kunyi@google.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
LTC2992 is a rail-to-rail system monitor that
measures current, voltage, and power of two supplies.
Two ADCs simultaneously measure each supply’s current.
A third ADC monitors the input voltages and four
auxiliary external voltages.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add hardware monitoring driver for the Maxim MAX127 chip.
MAX127 min/max range handling code is inspired by the max197 driver.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Link: https://lore.kernel.org/r/20201123185658.7632-2-rentao.bupt@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The Corsair digital power supplies of the series RMi, HXi and AXi include
a small micro-controller with a lot of sensors attached. The sensors can
be accessed by an USB connector from the outside.
This micro-controller provides the data by a simple proprietary USB HID
protocol. The data consist of temperatures, current and voltage levels,
power usage, uptimes, fan speed and some more. It is also possible to
configure the PSU (fan mode, mono/multi-rail, over current protection).
This driver provides access to the sensors/statistics of the RMi and HXi
series power supplies. It does not support configuring these devices,
because there would be many ways to misconfigure or even damage the PSU.
This patch adds:
- hwmon driver corsair-psu
- hwmon documentation
- updates MAINTAINERS
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/20201027131710.GA253280@monster.powergraphx.local
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for initialising shared (between children) Regmaps
- Add support for Kontron SL28CPLD
- Add support for ENE KB3930 Embedded Controller
- Add support for Intel FPGA PAC MAX 10 BMC
New Device Support:
- Add support for Power to Ricoh RN5T618
- Add support for UART to Intel Lakefield
- Add support for LP87524_Q1 to Texas Instruments LP87565
New Functionality:
- Device Tree; ene-kb3930, sl28cpld, syscon, lp87565, lp87524-q1
- Use new helper dev_err_probe(); madera-core, stmfx, wcd934x
- Use new GPIOD API; dm355evm_msp
- Add wake-up capability; sprd-sc27xx-spi
- Add ACPI support; kempld-core
Fix-ups:
- Trivial (spelling/whitespace); Kconfig, ab8500
- Fix for unused variables; khadas-mcu, kempld-core
- Remove unused header file(s); mt6360-core
- Use correct IRQ flags in docs; act8945a, gateworks-gsc, rohm,bd70528-pmic
- Add COMPILE_TEST support; asic3, tmio_core
- Add dependency on I2C; SL28CPLD
Bug Fixes:
- Fix memory leak(s); sm501
- Do not free regmap_config's 'name' until exit; syscon"
* tag 'mfd-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (34 commits)
mfd: kempld-core: Fix unused variable 'kempld_acpi_table' when !ACPI
mfd: sl28cpld: Depend on I2C
mfd: asic3: Build if COMPILE_TEST=y
dt-bindings: mfd: Correct interrupt flags in examples
mfd: Add ACPI support to Kontron PLD driver
mfd: intel-m10-bmc: Add Intel MAX 10 BMC chip support for Intel FPGA PAC
mfd: lp87565: Add LP87524-Q1 variant
dt-bindings: mfd: Add LP87524-Q1
dt-bindings: mfd: lp87565: Convert to yaml
mfd: mt6360: Remove unused include <linux/version.h>
mfd: sm501: Fix leaks in probe()
mfd: syscon: Don't free allocated name for regmap_config
dt-bindings: mfd: syscon: Document Exynos3 and Exynos5433 compatibles
dt-bindings: mfd: syscon: Merge Samsung Exynos Sysreg bindings
dt-bindings: mfd: ab8500: Remove weird Unicode characters
mfd: sprd: Add wakeup capability for PMIC IRQ
mfd: intel-lpss: Add device IDs for UART ports for Lakefield
mfd: dm355evm_msp: Convert LEDs to GPIO descriptor table
mfd: wcd934x: Simplify with dev_err_probe()
mfd: stmfx: Simplify with dev_err_probe()
...
|
|
PVT controller (MR75203) is used to configure & control
Moortec embedded analog IP which contains temprature
sensor(TS), voltage monitor(VM) & process detector(PD)
modules. Add hardware monitoring driver to support
MR75203 PVT controller.
Signed-off-by: Rahul Tanwar <rahul.tanwar@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/05b59cd860d2a1aa0a68ab300829efe709645184.1601889876.git.rahul.tanwar@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This patch adds hwmon functionality for Intel MAX 10 BMC chip. This BMC
chip connects to a set of sensor chips to monitor current, voltage,
thermal and power of different components on board. The BMC firmware is
responsible for sensor data sampling and recording in shared registers.
Host driver reads the sensor data from these shared registers and
exposes them to users as hwmon interfaces.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Wu Hao <hao.wu@intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1600669071-26235-3-git-send-email-yilun.xu@intel.com
[groeck: Adjusted subject]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for the hardware monitoring controller of the sl28cpld board
management controller. This driver is part of a multi-function device.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch adds a temperature sensor driver to the Sparx5 SoC.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200618135951.25441-4-lars.povlsen@microchip.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This is v7 of a driver for the Corsair Commander Pro.
It provides sysfs attributes for:
- Reading fan speed
- Reading temp sensors
- Reading voltage values
- Writing pwm and reading last written pwm
- Reading fan and temp connection status
It is an usb driver, so it needs to be ignored by usbhid.
The Corsair Commander Pro is a fan controller and provides
no means for user interaction.
The two device numbers are there, because there is a slightly
different version of the same device. (Only difference
seem to be in some presets.)
Squashed:
hwmon: (corsair-cpro) add fan_target
This adds fan_target entries to the corsair-cpro driver.
Reading the attribute from the device does not seem possible, so
it returns the last set value (same as pwm).
send_usb_cmd now has one more argument, which is needed for the
fan_target command.
hwmon: corsair-cpro: Change to HID driver
This changes corsair-cpro to a hid driver using hid reports.
Signed-off-by: Marius Zachmann <mail@mariuszachmann.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200626055936.4441-1-mail@mariuszachmann.de
Link: https://lore.kernel.org/r/20200709141413.30790-1-mail@mariuszachmann.de
[groeck: Squashed follow-up patches to avoid changes in HID code]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Baikal-T1 SoC provides an embedded process, voltage and temperature
sensor to monitor an internal SoC environment (chip temperature, supply
voltage and process monitor) and on time detect critical situations,
which may cause the system instability and even damages. The IP-block
is based on the Analog Bits PVT sensor, but is equipped with a
dedicated control wrapper, which provides a MMIO registers-based access
to the sensor core functionality (APB3-bus based) and exposes an
additional functions like thresholds/data ready interrupts, its status
and masks, measurements timeout. All of these is used to create a hwmon
driver being added to the kernel by this commit.
The driver implements support for the hardware monitoring capabilities
of Baikal-T1 process, voltage and temperature sensors. PVT IP-core
consists of one temperature and four voltage sensors, each of which is
implemented as a dedicated hwmon channel config.
The driver can optionally provide the hwmon alarms for each sensor the
PVT controller supports. The alarms functionality is made compile-time
configurable due to the hardware interface implementation peculiarity,
which is connected with an ability to convert data from only one sensor
at a time. Additional limitation is that the controller performs the
thresholds checking synchronously with the data conversion procedure.
Due to these limitations in order to have the hwmon alarms
automatically detected the driver code must switch from one sensor to
another, read converted data and manually check the threshold status
bits. Depending on the measurements timeout settings this design may
cause additional burden on the system performance. By default if the
alarms kernel config is disabled the data conversion is performed by
the driver on demand when read operation is requested via corresponding
_input-file.
Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru>
Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Immutable branch between MFD and HWMON due for the v5.8 merge window
|
|
This patch adds hwmon based amd_energy driver support for
family 17h processors from AMD.
The driver provides following interface to the userspace
1. Reports the per core consumption
* file: "energy%d_input", label: "Ecore%03d"
2. Reports per socket energy consumption
* file: "energy%d_input", label: "Esocket%d"
3. To, increase the wrap around time of the socket energy
counters, a 64bit accumultor is implemented.
4. Reports scaled energy value in Joules.
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Link: https://lore.kernel.org/r/20200519155011.56184-1-nchatrad@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The Gateworks System Controller has a hwmon sub-component that exposes
up to 16 ADC's, some of which are temperature sensors, others which are
voltage inputs. The ADC configuration (register mapping and name) is
configured via device-tree and varies board to board.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The purpose of this IP Core is to control the fan used for the cooling of a
Xilinx Zynq Ultrascale+ MPSoC without the need of any external temperature
sensors. To achieve this, the IP core uses the PL SYSMONE4 primitive to
obtain the PL temperature and, based on those readings, it then outputs
a PWM signal to control the fan rotation accordingly.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20191009102806.262241-1-nuno.sa@analog.com
[groeck: adi,pulses-per-revolution -> pulses-per-revolution;
dropped unused 'res' from probe function]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
ADM1177 is a Hot Swap Controller and Digital Power Monitor with
Soft Start Pin.
Datasheet:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1177.pdf
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Link: https://lore.kernel.org/r/20200114112159.25998-1-beniamin.bia@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Reading the temperature of ATA drives has been supported for years
by userspace tools such as smarttools or hddtemp. The downside of
such tools is that they need to run with super-user privilege, that
the temperatures are not reported by standard tools such as 'sensors'
or 'libsensors', and that drive temperatures are not available for use
in the kernel's thermal subsystem.
This driver solves this problem by adding support for reading the
temperature of ATA drives from the kernel using the hwmon API and
by adding a temperature zone for each drive.
With this driver, the hard disk temperature can be read using the
unprivileged 'sensors' application:
$ sensors drivetemp-scsi-1-0
drivetemp-scsi-1-0
Adapter: SCSI adapter
temp1: +23.0°C
or directly from sysfs:
$ grep . /sys/class/hwmon/hwmon9/{name,temp1_input}
/sys/class/hwmon/hwmon9/name:drivetemp
/sys/class/hwmon/hwmon9/temp1_input:23000
If the drive supports SCT transport and reports temperature limits,
those are reported as well.
drivetemp-scsi-0-0
Adapter: SCSI adapter
temp1: +27.0°C (low = +0.0°C, high = +60.0°C)
(crit low = -41.0°C, crit = +85.0°C)
(lowest = +23.0°C, highest = +34.0°C)
The driver attempts to use SCT Command Transport to read the drive
temperature. If the SCT Command Transport feature set is not available,
or if it does not report the drive temperature, drive temperatures may
be readable through SMART attributes. Since SMART attributes are not well
defined, this method is only used as fallback mechanism.
Cc: Chris Healy <cphealy@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
MAX31730 is a 3-Channel Remote Temperature Sensor.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
TI's TMP512/513 are I2C/SMBus system monitor chips. These chips
monitor the supply voltage, supply current, power consumption
and provide one local and up to three (TMP513) remote temperature sensors.
It has been tested using a TI TMP513 development kit (TMP513EVM)
Signed-off-by: Eric Tremblay <etremblay@distech-controls.com>
Link: https://lore.kernel.org/r/20191112223001.20844-3-etremblay@distech-controls.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The ltc2947 is a high precision power and energy monitor with an
internal sense resistor supporting up to +/- 30A. Three internal no
Latency ADCs ensure accurate measurement of voltage and current, while
high-bandwidth analog multiplication of voltage and current provides
accurate power measurement in a wide range of applications. Internal or
external clocking options enable precise charge and energy measurements.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20191021154115.319073-1-nuno.sa@analog.com
[groeck: Removed unnecessary checks when reading temperature and energy;
PAGE{0,1} -> LTC2947_PAGE_{0,1}]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Pull MIPS updates from Paul Burton:
"Main MIPS changes:
- boot_mem_map is removed, providing a nice cleanup made possible by
the recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
or MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of
Vincenzo Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic
SoCs.
- pte_special() is now supported for some configurations, allowing
among other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil,
mostly enabled by the inclusion of the new TCU (timer-counter unit)
drivers he's spent a very patient year or so working on. Plus some
fixes for X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"
* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
MIPS: Detect bad _PFN_SHIFT values
MIPS: Disable pte_special() for MIPS32 with RiXi
MIPS: ralink: deactivate PCI support for SOC_MT7621
mips: compat: vdso: Use legacy syscalls as fallback
MIPS: Drop Loongson _CACHE_* definitions
MIPS: tlbex: Remove cpu_has_local_ebase
MIPS: tlbex: Simplify r3k check
MIPS: Select R3k-style TLB in Kconfig
MIPS: PCI: refactor ioc3 special handling
mips: remove ioremap_cachable
mips/atomic: Fix smp_mb__{before,after}_atomic()
mips/atomic: Fix loongson_llsc_mb() wreckage
mips/atomic: Fix cmpxchg64 barriers
MIPS: Octeon: remove duplicated include from dma-octeon.c
firmware: bcm47xx_nvram: Allow COMPILE_TEST
firmware: bcm47xx_nvram: Correct size_t printf format
MIPS: Treat Loongson Extensions as ASEs
MIPS: Remove dev_err() usage after platform_get_irq()
MIPS: dts: mscc: describe the PTP ready interrupt
MIPS: dts: mscc: describe the PTP register range
...
|
|
Add a new driver for Synaptics AS370 PVT sensors. Currently, only
temperature is supported.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190827113259.4fb64a17@xhacker.debian
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
A driver for ADS1015 with more functionality is available in the iio
subsystem.
Remove the hwmon driver as duplicate. If the chip is used for hardware
monitoring, the iio->hwmon bridge should be used.
Cc: Dirk Eibach <eibach@gdsys.de>
Link: https://lore.kernel.org/r/1562004758-13025-1-git-send-email-linux@roeck-us.net
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The JZ4740 boards now use the iio-hwmon driver.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Paul Burton <paul.burton@mips.com>
|
|
Lochnagar is an evaluation and development board for Cirrus
Logic Smart CODEC and Amp devices. It allows the connection of
most Cirrus Logic devices on mini-cards, as well as allowing
connection of various application processor systems to provide a
full evaluation platform.
This driver adds support for the hardware monitoring features of
the Lochnagar 2 to the hwmon API. Monitoring is provided for
the board voltages, currents and temperature supported by the
board controller chip.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The OCC is a device embedded on a POWER processor that collects and
aggregates sensor data from the processor and system. The OCC can
provide the raw sensor data as well as perform thermal and power
management on the system.
This driver provides a hwmon interface to the OCC from a service
processor (e.g. a BMC). The driver supports both POWER8 and POWER9 OCCs.
Communications with the POWER8 OCC are established over standard I2C
bus. The driver communicates with the POWER9 OCC through the FSI-based
OCC driver, which handles the lower-level communication details.
This patch lays out the structure of the OCC hwmon driver. There are two
platform drivers, one each for P8 and P9 OCCs. These are probed through
the I2C tree and the FSI-based OCC driver, respectively. The patch also
defines the first common structures and methods between the two OCC
versions.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
[groeck: Fix up SPDX license identifier]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Pull ARM SoC driver updates from Olof Johansson:
"Some of the larger changes this merge window:
- Removal of drivers for Exynos5440, a Samsung SoC that never saw
widespread use.
- Uniphier support for USB3 and SPI reset handling
- Syste control and SRAM drivers and bindings for Allwinner platforms
- Qualcomm AOSS (Always-on subsystem) reset controller drivers
- Raspberry Pi hwmon driver for voltage
- Mediatek pwrap (pmic) support for MT6797 SoC"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (52 commits)
drivers/firmware: psci_checker: stash and use topology_core_cpumask for hotplug tests
soc: fsl: cleanup Kconfig menu
soc: fsl: dpio: Convert DPIO documentation to .rst
staging: fsl-mc: Remove remaining files
staging: fsl-mc: Move DPIO from staging to drivers/soc/fsl
staging: fsl-dpaa2: eth: move generic FD defines to DPIO
soc: fsl: qe: gpio: Add qe_gpio_set_multiple
usb: host: exynos: Remove support for Exynos5440
clk: samsung: Remove support for Exynos5440
soc: sunxi: Add the A13, A23 and H3 system control compatibles
reset: uniphier: add reset control support for SPI
cpufreq: exynos: Remove support for Exynos5440
ata: ahci-platform: Remove support for Exynos5440
soc: imx6qp: Use GENPD_FLAG_ALWAYS_ON for PU errata
soc: mediatek: pwrap: add mt6351 driver for mt6797 SoCs
soc: mediatek: pwrap: add pwrap driver for mt6797 SoCs
soc: mediatek: pwrap: fix cipher init setting error
dt-bindings: pwrap: mediatek: add pwrap support for MT6797
reset: uniphier: add USB3 core reset control
dt-bindings: reset: uniphier: add USB3 core reset support
...
|
|
Currently there is no easy way to detect undervoltage conditions on a
remote Raspberry Pi. This hwmon driver retrieves the state of the
undervoltage sensor via mailbox interface. The handling based on
Noralf's modifications to the downstream firmware driver. In case of
an undervoltage condition only an entry is written to the kernel log.
CC: "Noralf Trønnes" <noralf@tronnes.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
|
Zev Weiss
Michael Walle
Linus Torvalds
Guenter Roeck
Eugene Shalygin
Iwona Winiarska
Alistair Francis
Aleksandr Mezin
Denis Pauk
Nathan Rossi
Arun Saravanan Balachandran
Aleksa Savic
Lukas Bulwahn
Akshay Gupta
Navin Sankar Velliangiri
Jonas Malaco
Robert Marko
Johannes Cornelis Draaijer (datdenkikniet)
Kun Yi
Alexandru Tachici
Tao Ren
Wilken Gottwalt
Rahul Tanwar
Xu Yilun
Lars Povlsen
Marius Zachmann
Serge Semin
Naveen Krishna Chatradhi
Tim Harvey
Nuno Sá
Beniamin Bia
Eric Tremblay
Jisheng Zhang
Paul Cercueil
Lucas Tanure
Eddie James
Stefan Wahren