| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch is to add the AMBA device ID for CA73 CPU, so that CPU debug
module can be initialized successfully when a SoC contain CA73 CPUs.
This patch has been verified on 96boards Hikey960.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver prints pcsr twice: the first time it uses specifier %px to
print hexadecimal pcsr value and the second time uses specifier %pS for
output kernel symbols.
As suggested by Kees, using %pS should be sufficient and %px isn't
necessary; the reason is if the pcsr is a kernel space address, we can
easily get to know the code line from %pS format, on the other hand, if
the pcsr value doesn't fall into kernel space range (e.g. if the CPU is
stuck in firmware), %pS also gives out pcsr hexadecimal value.
So this commit removes useless %px and update section "Output format"
in the document for alignment between the code and document.
Suggested-by: Kees Cook <keescook@chromium.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Moving all kernel side CoreSight framework and drivers to SPDX identifier.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit ad67b74d2469 ("printk: hash addresses printed with %p") lets
printk specifier %p to hash all addresses before printing, this was
resulting in the high 32 bits of pcsr can only output zeros. So
module cannot completely print pc value and it's pointless for debugging
purpose.
This patch fixes this by using %px to print pcsr instead.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Coresight includes debug module and usually the module connects with CPU
debug logic. ARMv8 architecture reference manual (ARM DDI 0487A.k) has
description for related info in "Part H: External Debug".
Chapter H7 "The Sample-based Profiling Extension" introduces several
sampling registers, e.g. we can check program counter value with
combined CPU exception level, secure state, etc. So this is helpful for
analysis CPU lockup scenarios, e.g. if one CPU has run into infinite
loop with IRQ disabled. In this case the CPU cannot switch context and
handle any interrupt (including IPIs), as the result it cannot handle
SMP call for stack dump.
This patch is to enable coresight debug module, so firstly this driver
is to bind apb clock for debug module and this is to ensure the debug
module can be accessed from program or external debugger. And the driver
uses sample-based registers for debug purpose, e.g. when system triggers
panic, the driver will dump program counter and combined context
registers (EDCIDSR, EDVIDSR); by parsing context registers so can
quickly get to know CPU secure state, exception level, etc.
Some of the debug module registers are located in CPU power domain, so
this requires the CPU power domain stays on when access related debug
registers, but the power management for CPU power domain is quite
dependent on SoC integration for power management. For the platforms
which with sane power controller implementations, this driver follows
the method to set EDPRCR to try to pull the CPU out of low power state
and then set 'no power down request' bit so the CPU has no chance to
lose power.
If the SoC has not followed up this design well for power management
controller, the user should use the command line parameter or sysfs
to constrain all or partial idle states to ensure the CPU power
domain is enabled and access coresight CPU debug component safely.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Leo Yan
Mathieu Poirier
Arvind Yadav