| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch adds the support for setting up a SG table for use
by the CATU. We reuse the tmc_sg_table to represent the table/data
pages, even though the table format is different.
Similar to ETR SG table, CATU uses a 4KB page size for data buffers
as well as page tables. All table entries are 64bit wide and have
the following format:
63 12 1 0
x-----------------------------------x
| Address [63-12] | SBZ | V |
x-----------------------------------x
Where [V] -> 0 - Pointer is invalid
1 - Pointer is Valid
CATU uses only first half of the page for data page pointers.
i.e, single table page will only have 256 page pointers, addressing
upto 1MB of data. The second half of a table page contains only two
pointers at the end of the page (i.e, pointers at index 510 and 511),
which are used as links to the "Previous" and "Next" page tables
respectively.
The first table page has an "Invalid" previous pointer and the
next pointer entry points to the second page table if there is one.
Similarly the last table page has an "Invalid" next pointer to
indicate the end of the table chain.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the initial support for Coresight Address Translation Unit, which
augments the TMC in Coresight SoC-600 by providing an improved Scatter
Gather mechanism. CATU is always connected to a single TMC-ETR and
converts the AXI address with a translated address (from a given SG
table with specific format). The CATU should be programmed in pass
through mode and enabled even if the ETR doesn't use the translation
by CATU.
This patch provides mechanism to enable/disable the CATU always in the
pass through mode.
We reuse the existing ports mechanism to link the TMC-ETR to the
connected CATU.
i.e, TMC-ETR:output_port0 -> CATU:input_port0
Reference manual for CATU component is avilable in version r2p0 of :
"Arm Coresight System-on-Chip SoC-600 Technical Reference Manual".
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a new coresight device type, which do not belong to any
of the existing types, i.e, source, sink, link etc. A helper
device could be connected to a coresight device, which could
augment the functionality of the coresight device.
This is intended to cover Coresight Address Translation Unit (CATU)
devices, which provide improved Scatter Gather mechanism for TMC
ETR. The idea is that the helper device could be controlled by
the driver of the device it is attached to (in this case ETR),
transparent to the generic coresight driver (and paths).
The operations include enable(), disable(), both of which could
accept a device specific "data" which the driving device and
the helper device could share. Since they don't appear in the
coresight "path" tracked by software, we have to ensure that
they are powered up/down whenever the master device is turned
on.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If we fail to find the input / output port for a LINK component
while enabling a path, we should fail gracefully rather than
assuming port "0".
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We request for "CORESIGHT_BARRIER_PKT_SIZE" length and we should
be happy when we get that size.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The newly introduced code fails to build in some configurations
unless we include the right headers:
drivers/hwtracing/coresight/coresight-tmc-etr.c: In function 'tmc_free_table_pages':
drivers/hwtracing/coresight/coresight-tmc-etr.c:206:3: error: implicit declaration of function 'vunmap'; did you mean 'iounmap'? [-Werror=implicit-function-declaration]
Fixes: 79613ae8715a ("coresight: Add generic TMC sg table framework")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that we can dynamically switch between contiguous memory and
SG table depending on the trace buffer size, provide the support
for selecting an appropriate buffer size.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the support for Scatter-Gather mode to the etr-buf layer.
Since we now have two different modes, we choose the backend
based on a set of conditions, documented in the code.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The TMC-ETR can use the target trace buffer in two different modes.
Normal physically contiguous mode and a discontiguous list pages in
Scatter-Gather mode. Also we have dedicated Coresight component, CATU
(Coresight Address Translation Unit) to provide improved scatter-gather
mode in Coresight SoC-600. This complicates the management of the
buffer used for trace, depending on the mode in which ETR is configured.
So, this patch adds a transparent layer for managing the ETR buffer
which abstracts the basic operations on the buffer (alloc, free,
sync and retrieve the data) and uses the mode specific helpers to
do the actual operation. This also allows the ETR driver to choose
the best mode for a given use case and adds the flexibility to
fallback to a different mode, without duplicating the code.
The patch also adds the "normal" flat memory mode and switches
the sysfs driver to use the new layer.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds support for setting up an SG table used by the
TMC ETR inbuilt SG unit. The TMC ETR uses 4K page sized tables
to hold pointers to the 4K data pages with the last entry in a
table pointing to the next table with the entries, by kind of
chaining. The 2 LSBs determine the type of the table entry, to
one of :
Normal - Points to a 4KB data page.
Last - Points to a 4KB data page, but is the last entry in the
page table.
Link - Points to another 4KB table page with pointers to data.
The code takes care of handling the system page size which could
be different than 4K. So we could end up putting multiple ETR
SG tables in a single system page, vice versa for the data pages.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch introduces a generic sg table data structure and
associated operations. An SG table can be used to map a set
of Data pages where the trace data could be stored by the TMC
ETR. The information about the data pages could be stored in
different formats, depending on the type of the underlying
SG mechanism (e.g, TMC ETR SG vs Coresight CATU). The generic
structure provides book keeping of the pages used for the data
as well as the table contents. The table should be filled by
the user of the infrastructure.
A table can be created by specifying the number of data pages
as well as the number of table pages required to hold the
pointers, where the latter could be different for different
types of tables. The pages are mapped in the appropriate dma
data direction mode (i.e, DMA_TO_DEVICE for table pages
and DMA_FROM_DEVICE for data pages). The framework can optionally
accept a set of allocated data pages (e.g, perf ring buffer) and
map them accordingly. The table and data pages are vmap'ed to allow
easier access by the drivers. The framework also provides helpers to
sync the data written to the pages with appropriate directions.
This will be later used by the TMC ETR SG unit and CATU.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We are about to add the support for ETR builtin scatter-gather mode
for dealing with large amount of trace buffers. However, on some of
the platforms, using the ETR SG mode can lock up the system due to
the way the ETR is connected to the memory subsystem.
In SG mode, the ETR performs READ from the scatter-gather table to
fetch the next page and regular WRITE of trace data. If the READ
operation doesn't complete(due to the memory subsystem issues,
which we have seen on a couple of platforms) the trace WRITE
cannot proceed leading to issues. So, we by default do not
use the SG mode, unless it is known to be safe on the platform.
We define a DT property for the TMC node to specify whether we
have a proper SG mode.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: John Horley <john.horley@arm.com>
Cc: Robert Walker <robert.walker@arm.com>
Cc: devicetree@vger.kernel.org
Cc: frowand.list@gmail.com
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Right now we open code filling the trace buffer with synchronization
packets when the circular buffer wraps around in different drivers.
Move this to a common place. While at it, clean up the barrier_pkt
array to strip off the trailing '\0'.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We don't support ETR in perf mode yet. So, don't
even try to enable the hardware, even by mistake.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We zero out the entire trace buffer used for ETR before it is enabled,
for helping with debugging. With the addition of scatter-gather mode,
the buffer could be bigger and non-contiguous.
Get rid of this step; if someone wants to debug, they can always add it
as and when needed.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
At the moment we adjust the buffer pointers for reading the trace
data via misc device in the common code for ETF/ETB and ETR. Since
we are going to change how we manage the buffer for ETR, let us
move the buffer manipulation to the respective driver files, hiding
it from the common code. We do so by adding type specific helpers
for finding the length of data and the pointer to the buffer,
for a given length at a file position.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add ETM PIDs of the Arm cortex-A CPUs to the white list of ETMs.
While at it add a helper macro to make it easier to add the new
entries.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As with ETM3x, the ETM4x tracers can trigger trace acquisition based on
contextID value, something that isn't useful when PID namespaces are
enabled. Indeed the PID value of a process has a different representation
in the kernel and the PID namespace, making the feature confusing and
potentially leaking internal kernel information.
As such simply return an error when the feature is being used from a
PID namespace other than the default one.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Kim Phillips <kim.phillips@arm.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Tracers can trigger trace acquisition based on contextID value, something
that isn't useful when PID namespaces are enabled. Indeed the PID value
of a process has a different representation in the kernel and the PID
namespace, making the feature confusing and potentially leaking internal
kernel information.
As such simply return an error when the feature is being used from a
PID namespace other than the default one.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Kim Phillips <kim.phillips@arm.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The devm_kzalloc() function has a 2-factor argument form, devm_kcalloc().
This patch replaces cases of:
devm_kzalloc(handle, a * b, gfp)
with:
devm_kcalloc(handle, a * b, gfp)
as well as handling cases of:
devm_kzalloc(handle, a * b * c, gfp)
with:
devm_kzalloc(handle, array3_size(a, b, c), gfp)
as it's slightly less ugly than:
devm_kcalloc(handle, array_size(a, b), c, gfp)
This does, however, attempt to ignore constant size factors like:
devm_kzalloc(handle, 4 * 1024, gfp)
though any constants defined via macros get caught up in the conversion.
Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.
Some manual whitespace fixes were needed in this patch, as Coccinelle
really liked to write "=devm_kcalloc..." instead of "= devm_kcalloc...".
The Coccinelle script used for this was:
// Fix redundant parens around sizeof().
@@
expression HANDLE;
type TYPE;
expression THING, E;
@@
(
devm_kzalloc(HANDLE,
- (sizeof(TYPE)) * E
+ sizeof(TYPE) * E
, ...)
|
devm_kzalloc(HANDLE,
- (sizeof(THING)) * E
+ sizeof(THING) * E
, ...)
)
// Drop single-byte sizes and redundant parens.
@@
expression HANDLE;
expression COUNT;
typedef u8;
typedef __u8;
@@
(
devm_kzalloc(HANDLE,
- sizeof(u8) * (COUNT)
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(__u8) * (COUNT)
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(char) * (COUNT)
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(unsigned char) * (COUNT)
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(u8) * COUNT
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(__u8) * COUNT
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(char) * COUNT
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(unsigned char) * COUNT
+ COUNT
, ...)
)
// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
expression HANDLE;
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@
(
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * (COUNT_ID)
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * COUNT_ID
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * (COUNT_CONST)
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * COUNT_CONST
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * (COUNT_ID)
+ COUNT_ID, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * COUNT_ID
+ COUNT_ID, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * (COUNT_CONST)
+ COUNT_CONST, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * COUNT_CONST
+ COUNT_CONST, sizeof(THING)
, ...)
)
// 2-factor product, only identifiers.
@@
expression HANDLE;
identifier SIZE, COUNT;
@@
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- SIZE * COUNT
+ COUNT, SIZE
, ...)
// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression HANDLE;
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@
(
devm_kzalloc(HANDLE,
- sizeof(TYPE) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
)
// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression HANDLE;
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@
(
devm_kzalloc(HANDLE,
- sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
)
// 3-factor product, only identifiers, with redundant parens removed.
@@
expression HANDLE;
identifier STRIDE, SIZE, COUNT;
@@
(
devm_kzalloc(HANDLE,
- (COUNT) * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- COUNT * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- COUNT * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- (COUNT) * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- COUNT * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- (COUNT) * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- (COUNT) * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- COUNT * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
)
// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression HANDLE;
expression E1, E2, E3;
constant C1, C2, C3;
@@
(
devm_kzalloc(HANDLE, C1 * C2 * C3, ...)
|
devm_kzalloc(HANDLE,
- (E1) * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
|
devm_kzalloc(HANDLE,
- (E1) * (E2) * E3
+ array3_size(E1, E2, E3)
, ...)
|
devm_kzalloc(HANDLE,
- (E1) * (E2) * (E3)
+ array3_size(E1, E2, E3)
, ...)
|
devm_kzalloc(HANDLE,
- E1 * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
)
// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression HANDLE;
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@
(
devm_kzalloc(HANDLE, sizeof(THING) * C2, ...)
|
devm_kzalloc(HANDLE, sizeof(TYPE) * C2, ...)
|
devm_kzalloc(HANDLE, C1 * C2 * C3, ...)
|
devm_kzalloc(HANDLE, C1 * C2, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * (E2)
+ E2, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * E2
+ E2, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * (E2)
+ E2, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * E2
+ E2, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- (E1) * E2
+ E1, E2
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- (E1) * (E2)
+ E1, E2
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- E1 * E2
+ E1, E2
, ...)
)
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
The driver prints pcsr twice: the first time it uses specifier %px to
print hexadecimal pcsr value and the second time uses specifier %pS for
output kernel symbols.
As suggested by Kees, using %pS should be sufficient and %px isn't
necessary; the reason is if the pcsr is a kernel space address, we can
easily get to know the code line from %pS format, on the other hand, if
the pcsr value doesn't fall into kernel space range (e.g. if the CPU is
stuck in firmware), %pS also gives out pcsr hexadecimal value.
So this commit removes useless %px and update section "Output format"
in the document for alignment between the code and document.
Suggested-by: Kees Cook <keescook@chromium.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The simple removal of an extra newline, no change in functionality.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Variable 'paddr' can't be used if uninitialised but is nonetheless
confusing to some static checker. As such simply initialise it to zero.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While operating from sysFS the TMC-ETR driver needs to make sure it has
memory to work with but doesn't allocate memory uselessly either. Since
the main memory handle for this driver is drvdata::vaddr, use it throughout
function tmc_enable_etr_sink_sysfs() so that things are consistent.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Moving all kernel side CoreSight framework and drivers to SPDX identifier.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Never directly free @dev after calling device_register(), even
if it returned an error. Always use put_device() to give up the
reference initialized.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc driver patches for 4.17-rc1.
There are a lot of little things in here, nothing huge, but all
important to the different hardware types involved:
- thunderbolt driver updates
- parport updates (people still care...)
- nvmem driver updates
- mei updates (as always)
- hwtracing driver updates
- hyperv driver updates
- extcon driver updates
- ... and a handful of even smaller driver subsystem and individual
driver updates
All of these have been in linux-next with no reported issues"
* tag 'char-misc-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (149 commits)
hwtracing: Add HW tracing support menu
intel_th: Add ACPI glue layer
intel_th: Allow forcing host mode through drvdata
intel_th: Pick up irq number from resources
intel_th: Don't touch switch routing in host mode
intel_th: Use correct method of finding hub
intel_th: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate
stm class: Make dummy's master/channel ranges configurable
stm class: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate
MAINTAINERS: Bestow upon myself the care for drivers/hwtracing
hv: add SPDX license id to Kconfig
hv: add SPDX license to trace
Drivers: hv: vmbus: do not mark HV_PCIE as perf_device
Drivers: hv: vmbus: respect what we get from hv_get_synint_state()
/dev/mem: Avoid overwriting "err" in read_mem()
eeprom: at24: use SPDX identifier instead of GPL boiler-plate
eeprom: at24: simplify the i2c functionality checking
eeprom: at24: fix a line break
eeprom: at24: tweak newlines
eeprom: at24: refactor at24_probe()
...
|
|
This is a cosmetic patch that deals with the address filter structure's
ambiguous fields 'filter' and 'range'. The former stands to mean that the
filter's *action* should be to filter the traces to its address range if
it's set or stop tracing if it's unset. This is confusing and hard on the
eyes, so this patch replaces it with 'action' enum. The 'range' field is
completely redundant (meaning that the filter is an address range as
opposed to a single address trigger), as we can use zero size to mean the
same thing.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Will Deacon <will.deacon@arm.com>
Link: http://lkml.kernel.org/r/20180329120648.11902-1-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
ctxid_pid and vmid_val in config are of type u64. When an integer
0xFF is being left shifted more than 32 bits, the behavior is
undefined. The fix is to specify 0xFF as an unsigned long.
Detected by Coverity scan: CID 37650, 37651 (Bad bit shift operation)
Signed-off-by: Bo Yan <byan@nvidia.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit ad67b74d2469 ("printk: hash addresses printed with %p") lets
printk specifier %p to hash all addresses before printing, this was
resulting in the high 32 bits of pcsr can only output zeros. So
module cannot completely print pc value and it's pointless for debugging
purpose.
This patch fixes this by using %px to print pcsr instead.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull char/misc driver updates from Greg KH:
"Here is the big pull request for char/misc drivers for 4.16-rc1.
There's a lot of stuff in here. Three new driver subsystems were added
for various types of hardware busses:
- siox
- slimbus
- soundwire
as well as a new vboxguest subsystem for the VirtualBox hypervisor
drivers.
There's also big updates from the FPGA subsystem, lots of Android
binder fixes, the usual handful of hyper-v updates, and lots of other
smaller driver updates.
All of these have been in linux-next for a long time, with no reported
issues"
* tag 'char-misc-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (155 commits)
char: lp: use true or false for boolean values
android: binder: use VM_ALLOC to get vm area
android: binder: Use true and false for boolean values
lkdtm: fix handle_irq_event symbol for INT_HW_IRQ_EN
EISA: Delete error message for a failed memory allocation in eisa_probe()
EISA: Whitespace cleanup
misc: remove AVR32 dependencies
virt: vbox: Add error mapping for VERR_INVALID_NAME and VERR_NO_MORE_FILES
soundwire: Fix a signedness bug
uio_hv_generic: fix new type mismatch warnings
uio_hv_generic: fix type mismatch warnings
auxdisplay: img-ascii-lcd: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
uio_hv_generic: add rescind support
uio_hv_generic: check that host supports monitor page
uio_hv_generic: create send and receive buffers
uio: document uio_hv_generic regions
doc: fix documentation about uio_hv_generic
vmbus: add monitor_id and subchannel_id to sysfs per channel
vmbus: fix ABI documentation
uio_hv_generic: use ISR callback method
...
|
|
Reuse the new generic helper, of_cpu_node_to_id() to map a
given CPU phandle to a logical CPU number.
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The CoreSight TPIU should be disabled when tracing to other sinks to allow
them to operate at full bandwidth.
This patch fixes tpiu_disable_hw() to correctly disable the TPIU by
configuring the TPIU to stop on flush, initiating a manual flush, waiting
for the flush to complete and then waits for the TPIU to indicate it has
stopped.
Signed-off-by: Robert Walker <robert.walker@arm.com>
Tested-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix ptr_ret.cocci warnings:
drivers/hwtracing/coresight/coresight-tpiu.c:163:1-3: WARNING: PTR_ERR_OR_ZERO can be used
drivers/hwtracing/coresight/coresight-funnel.c:217:1-3: WARNING: PTR_ERR_OR_ZERO can be used
drivers/hwtracing/coresight/coresight-dynamic-replicator.c:166:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
No need to reinvent the wheel, we have bus_find_device_by_name().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc and other driver subsystem patches
for 4.15-rc1.
There are small changes all over here, hyperv driver updates, pcmcia
driver updates, w1 driver updats, vme driver updates, nvmem driver
updates, and lots of other little one-off driver updates as well. The
shortlog has the full details.
All of these have been in linux-next for quite a while with no
reported issues"
* tag 'char-misc-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (90 commits)
VME: Return -EBUSY when DMA list in use
w1: keep balance of mutex locks and refcnts
MAINTAINERS: Update VME subsystem tree.
nvmem: sunxi-sid: add support for A64/H5's SID controller
nvmem: imx-ocotp: Update module description
nvmem: imx-ocotp: Enable i.MX7D OTP write support
nvmem: imx-ocotp: Add i.MX7D timing write clock setup support
nvmem: imx-ocotp: Move i.MX6 write clock setup to dedicated function
nvmem: imx-ocotp: Add support for banked OTP addressing
nvmem: imx-ocotp: Pass parameters via a struct
nvmem: imx-ocotp: Restrict OTP write to IMX6 processors
nvmem: uniphier: add UniPhier eFuse driver
dt-bindings: nvmem: add description for UniPhier eFuse
nvmem: set nvmem->owner to nvmem->dev->driver->owner if unset
nvmem: qfprom: fix different address space warnings of sparse
nvmem: mtk-efuse: fix different address space warnings of sparse
nvmem: mtk-efuse: use stack for nvmem_config instead of malloc'ing it
nvmem: imx-iim: use stack for nvmem_config instead of malloc'ing it
thunderbolt: tb: fix use after free in tb_activate_pcie_devices
MAINTAINERS: Add git tree for Thunderbolt development
...
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As per coresight standards, PIDR2 register has the following format :
[2-0] - JEP106_bits6to4
[3] - JEDEC, designer ID is specified by JEDEC.
However some of the drivers only use mask of 0x3 for the PIDR2 leaving
bits [3-2] unchecked, which could potentially match the component for
a different device altogether. This patch fixes the mask and the
corresponding id bits for the existing devices.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The casting and other things here is odd, and causes sparse to
complain:
drivers/hwtracing/coresight/coresight-stm.c:279:35: warning: incorrect type in argument 1 (different address spaces)
drivers/hwtracing/coresight/coresight-stm.c:279:35: expected void [noderef] <asn:2>*addr
drivers/hwtracing/coresight/coresight-stm.c:279:35: got struct stm_drvdata *drvdata
drivers/hwtracing/coresight/coresight-stm.c:327:17: warning: incorrect type in argument 2 (different address spaces)
drivers/hwtracing/coresight/coresight-stm.c:327:17: expected void volatile [noderef] <asn:2>*addr
drivers/hwtracing/coresight/coresight-stm.c:327:17: got void *addr
drivers/hwtracing/coresight/coresight-stm.c:330:17: warning: incorrect type in argument 2 (different address spaces)
drivers/hwtracing/coresight/coresight-stm.c:330:17: expected void volatile [noderef] <asn:2>*addr
drivers/hwtracing/coresight/coresight-stm.c:330:17: got void *addr
drivers/hwtracing/coresight/coresight-stm.c:333:17: warning: incorrect type in argument 2 (different address spaces)
drivers/hwtracing/coresight/coresight-stm.c:333:17: expected void volatile [noderef] <asn:2>*addr
drivers/hwtracing/coresight/coresight-stm.c:333:17: got void *addr
>From what I can tell, we don't really need to treat ch_addr as
anything besides a pointer, and we can just do pointer math
instead of ORing in the bits of the offset and achieve the same
thing.
Also, we were passing a drvdata pointer to the
coresight_timeout() function, but we really wanted to pass the
address of the register base. Luckily the base is the first
member of the structure, so everything works out, but this is
quite unsafe if we ever change the structure layout. Clean this
all up so sparse stops complaining on this code.
Reported-by: Satyajit Desai <sadesai@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the peripheral ids for the Coresight SoC 600 TPIU, replicator
and funnel.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Suzuki K Poulose
Arnd Bergmann
Mathieu Poirier
Kees Cook
Leo Yan
Arvind Yadav
Linus Torvalds
Alexander Shishkin
Bo Yan
Pravin Shedge
Robert Walker
Vasyl Gomonovych
Lukas Wunner
Greg Kroah-Hartman
Stephen Boyd