| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The driver treats the device descriptors as CPU-endian, which appears
to be correct with the default endianness on both ARM (typically LE)
and PowerPC (typically BE) SoCs, indicating that the hardware block
is generated differently. Add endianness annotations and byteswaps as
necessary.
It's not clear that the ifdef there really is correct and shouldn't
just be #ifdef CONFIG_ARM, but I also can't test on anything but the
i.MX6 HummingBoard where this gets it working with a BE kernel.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 76e398a62712 ("net: dsa: use switchdev obj for VLAN add/del
ops"), the Marvell 88E6xxx switch has been unable to pass traffic
between ports - any received traffic is discarded by the switch.
Taking a port out of bridge mode and configuring a vlan on it also the
port to start passing traffic.
With the debugfs files re-instated to allow debug of this issue by
comparing the register settings between the working and non-working
case, the reason becomes clear:
GLOBAL GLOBAL2 SERDES 0 1 2 3 4 5 6
- 7: 1111 707f 2001 2 2 2 2 2 0 2
+ 7: 1111 707f 2001 1 1 1 1 1 0 1
Register 7 for the ports is the default vlan tag register, and in the
non-working setup, it has been set to 2, despite vlan 2 not being
configured. This causes the switch to drop all packets coming in to
these ports. The working setup has the default vlan tag register set
to 1, which is the default vlan when none is configured.
Inspection of the code reveals why. The code prior to this commit
was:
- for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) {
...
- if (!err && vlan->flags & BRIDGE_VLAN_INFO_PVID)
- err = ds->drv->port_pvid_set(ds, p->port, vid);
but the new code is:
+ for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) {
...
+ }
...
+ if (pvid)
+ err = _mv88e6xxx_port_pvid_set(ds, port, vid);
This causes the new code to always set the default vlan to one higher
than the old code.
Fix this.
Fixes: 76e398a62712 ("net: dsa: use switchdev obj for VLAN add/del ops")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is an additional patch to the one already submitted recently.
The previous patch was not complete, and the FCC port lock-up scenario
has been reproduced in lab.
I had an opportunity to check the current patch in lab and the FCC
port lock no longer freezes, while the previous patch still locks-up the
FCC port.
The current patch fixes a pointer arithmetic bug (second bug in the same
line), which leads FCC port lock-up during underrun/collision handling.
Within the tx_startup() function in mac-fcc.c, the address of last BD is
not calculated correctly. As a result of wrong calculation of the last BD
address, the next transmitted BD may be set to an area out of the transmit
BD ring. This actually causes to port lock-up and it is not recoverable.
Signed-off-by: Martin Roth <martin.roth@motorolasolutions.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ESP algorithms using CBC mode require echainiv. Hence INET*_ESP have
to select CRYPTO_ECHAINIV in order to work properly. This solves the
issues caused by a misconfiguration as described in [1].
The original approach, patching crypto/Kconfig was turned down by
Herbert Xu [2].
[1] https://lists.strongswan.org/pipermail/users/2015-December/009074.html
[2] http://marc.info/?l=linux-crypto-vger&m=145224655809562&w=2
Signed-off-by: Thomas Egerer <hakke_007@gmx.de>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch extends commit b93d6471748d ("sctp: implement the sender side
for SACK-IMMEDIATELY extension") as it didn't white list
SCTP_SACK_IMMEDIATELY on sctp_msghdr_parse(), causing it to be
understood as an invalid flag and returning -EINVAL to the application.
Note that the actual handling of the flag is already there in
sctp_datamsg_from_user().
https://tools.ietf.org/html/rfc7053#section-7
Fixes: b93d6471748d ("sctp: implement the sender side for SACK-IMMEDIATELY extension")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The napi_synchronize() function is defined twice: The definition
for SMP builds waits for other CPUs to be done, while the uniprocessor
variant just contains a barrier and ignores its argument.
In the mvneta driver, this leads to a warning about an unused variable
when we lookup the NAPI struct of another CPU and then don't use it:
ethernet/marvell/mvneta.c: In function 'mvneta_percpu_notifier':
ethernet/marvell/mvneta.c:2910:30: error: unused variable 'other_port' [-Werror=unused-variable]
There are no other CPUs on a UP build, so that code never runs, but
gcc does not know this.
The nicest solution seems to be to turn the napi_synchronize() helper
into an inline function for the UP case as well, as that leads gcc to
not complain about the argument being unused. Once we do that, we can
also combine the two cases into a single function definition and use
if(IS_ENABLED()) rather than #ifdef to make it look a bit nicer.
The warning first came up in linux-4.4, but I failed to catch it
earlier.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: f86428854480 ("net: mvneta: Statically assign queues to CPUs")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several times already this has been reported as kasan reports caused by
syzkaller and trinity and people always looked at RCU races, but it is
much more simple. :)
In case we bind a pptp socket multiple times, we simply add it to
the callid_sock list but don't remove the old binding. Thus the old
socket stays in the bucket with unused call_id indexes and doesn't get
cleaned up. This causes various forms of kasan reports which were hard
to pinpoint.
Simply don't allow multiple binds and correct error handling in
pptp_bind. Also keep sk_state bits in place in pptp_connect.
Fixes: 00959ade36acad ("PPTP: PPP over IPv4 (Point-to-Point Tunneling Protocol)")
Cc: Dmitry Kozlov <xeb@mail.ru>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For interrupt controller that doesn't support irq_disable and hardware
with level interrupt, an extra interrupt may be pending. This patch fixes
the issue by setting IRQ_DISABLE_UNLAZY flag for the interrupt line,
as suggested by,
'commit e9849777d0e2 ("genirq: Add flag to force mask in
disable_irq[_nosync]()")'
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dmitry reported a struct pid leak detected by a syzkaller program.
Bug happens in unix_stream_recvmsg() when we break the loop when a
signal is pending, without properly releasing scm.
Fixes: b3ca9b02b007 ("net: fix multithreaded signal handling in unix recv routines")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cgroup methods are no longer used after baac50bbc3cd ("net:
tcp_memcontrol: simplify linkage between socket and page counter").
The hunk to delete them was included in the original patch but must
have gotten lost during conflict resolution on the way upstream.
Fixes: baac50bbc3cd ("net: tcp_memcontrol: simplify linkage between socket and page counter")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the lan87xx_read_status function is getting called the
energy detect mode is enabled again even if it has been
disabled by device tree.
Added private struct to check the energy detect status.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some platforms may provide more than one clk for the mvneta IP, for
example Marvell BG4CT provides one clk for the mac core, and one
clk for the AXI bus logic. Obviously this bus clk also need to
be enabled. This patch adds this optional "bus" clk support.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some platforms may provide more than one clk for the mvneta IP, for
example Marvell BG4CT provides one clk for the mac core, and one
clk for the AXI bus logic.
To support for more than one clock, we'll need to distinguish between
the clock by name. Change clock probing to first try to get "core"
clock before falling back to unnamed clock.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sorting the headers in alphabetic order will help to reduce the conflict
when adding new headers in the future.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When s->type is T_REG_64, the high 32bits are lost in val. This patch
fixes this trivial issue.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Fixes: 9b0cdefa4cd5 ("net: mvneta: add ethtool statistics")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch replace the assoication between dsaf and enet from string
matching to object reference. It requires the DTS to be updated within
BIOS. Thanks god it can be done for all released boards.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Neal reported crashes with this stack trace :
RIP: 0010:[<ffffffff8c57231b>] tcp_v4_send_ack+0x41/0x20f
...
CR2: 0000000000000018 CR3: 000000044005c000 CR4: 00000000001427e0
...
[<ffffffff8c57258e>] tcp_v4_reqsk_send_ack+0xa5/0xb4
[<ffffffff8c1a7caa>] tcp_check_req+0x2ea/0x3e0
[<ffffffff8c19e420>] tcp_rcv_state_process+0x850/0x2500
[<ffffffff8c1a6d21>] tcp_v4_do_rcv+0x141/0x330
[<ffffffff8c56cdb2>] sk_backlog_rcv+0x21/0x30
[<ffffffff8c098bbd>] tcp_recvmsg+0x75d/0xf90
[<ffffffff8c0a8700>] inet_recvmsg+0x80/0xa0
[<ffffffff8c17623e>] sock_aio_read+0xee/0x110
[<ffffffff8c066fcf>] do_sync_read+0x6f/0xa0
[<ffffffff8c0673a1>] SyS_read+0x1e1/0x290
[<ffffffff8c5ca262>] system_call_fastpath+0x16/0x1b
The problem here is the skb we provide to tcp_v4_send_ack() had to
be parked in the backlog of a new TCP fastopen child because this child
was owned by the user at the time an out of window packet arrived.
Before queuing a packet, TCP has to set skb->dev to NULL as the device
could disappear before packet is removed from the queue.
Fix this issue by using the net pointer provided by the socket (being a
timewait or a request socket).
IPv6 is immune to the bug : tcp_v6_send_response() already gets the net
pointer from the socket if provided.
Fixes: 168a8f58059a ("tcp: TCP Fast Open Server - main code path")
Reported-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jerry Chu <hkchu@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When configuring checksums on UDP tunnels, the flags are different
for IPv4 vs. IPv6 (and reversed). However, when lightweight tunnels
are enabled the flags used are always the IPv4 versions, which are
ignored in the IPv6 code paths. This uses the correct IPv6 flags, so
checksums can be controlled appropriately.
Fixes: a725e514 ("vxlan: metadata based tunneling for IPv6")
Fixes: abe492b4 ("geneve: UDP checksum configuration via netlink")
Signed-off-by: Jesse Gross <jesse@kernel.org>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By the time we execute bcmgenet_mii_probe(), the MDIO bus structure has
long been allocated and registered. Overirring the PHY interrupt using
the MDIO bus structure has no chance to work anymore, because
of_mdiobus_register() has call phy_device_create() for use, which copied
the MDIO bus address's irq for the PHY into the PHY device "irq" member.
Since we do have a proper reference to a PHY device in
bcmgenet_mii_probe(), just assign the desired IRQ value here.
Fixes: aa09677cba42 ("net: bcmgenet: add MDIO routines")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 5ea94e7686a3 ("phy: add phy_mac_interrupt()") to use with
PHY_IGNORE_INTERRUPT added a cancel_work_sync() into phy_mac_interrupt()
which is allowed to sleep, whereas phy_mac_interrupt() is expected to be
callable from interrupt context.
Now that we have fixed how the PHY state machine treats
PHY_IGNORE_INTERRUPT with respect to state changes, we can just set the
new link state, and queue the PHY state machine for execution so it is
going to read the new link state.
For that to work properly, we need to update phy_change() not to try to
invoke any interrupt callbacks if we have configured the PHY device for
PHY_IGNORE_INTERRUPT, because that PHY device and its driver are not
required to implement those.
Fixes: 5ea94e7686a3 ("phy: add phy_mac_interrupt() to use with PHY_IGNORE_INTERRUPT")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 2c7b49212a86 ("phy: fix the use of PHY_IGNORE_INTERRUPT") changed
a hunk in phy_state_machine() in the PHY_RUNNING case which was not
needed. The change essentially makes the PHY library treat PHY devices
with PHY_IGNORE_INTERRUPT to keep polling for the PHY device, even
though the intent is not to do it.
Fix this by reverting that specific hunk, which makes the PHY state
machine wait for state changes, and stay in the PHY_RUNNING state for as
long as needed.
Fixes: 2c7b49212a86 ("phy: fix the use of PHY_IGNORE_INTERRUPT")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The defconfig build of blackfin is failing with the error:
arch/blackfin/include/asm/bfin_serial.h:269:0: warning: "port_membase" redefined
drivers/net/irda/bfin_sir.h:85:0: note: this is the location of the previous definition
arch/blackfin/include/asm/bfin_serial.h:382:0: warning: "get_lsr_cache" redefined
drivers/net/irda/bfin_sir.h:86:0: note: this is the location of the previous definition
arch/blackfin/include/asm/bfin_serial.h:383:0: warning: "put_lsr_cache" redefined
drivers/net/irda/bfin_sir.h:87:0: note: this is the location of the previous definition
port_membase, get_lsr_cache, put_lsr_cache are already defined in the
architecture files, no need to define them again in the driver.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Documentation should be kept consistent with the code:
static int tcp_syn_retries_max = MAX_TCP_SYNCNT;
#define MAX_TCP_SYNCNT 127
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PHY status frames are not reliable, the PHY may not be able to send them
during heavy receive traffic. This overflow condition is signaled by the
PHY in the next status frame, but the driver did not make use of it.
Instead it always reported wrong tx timestamps to user space after an
overflow happened because it assigned newly received tx timestamps to old
packets in the queue.
This commit fixes this issue by clearing the tx timestamp queue every time
an overflow happens, so that no timestamps are delivered for overflow
packets. This way time stamping will continue correctly after an overflow.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicron.at>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lorenzo reported that we could not properly find v4mapped sockets
in inet_diag_find_one_icsk(). This patch fixes the issue.
Reported-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GRO is currently not aware of tunnel metadata generated by lightweight
tunnels and stored in the dst. This leads to two possible problems:
* Incorrectly merging two frames that have different metadata.
* Leaking of allocated metadata from merged frames.
This avoids those problems by comparing the tunnel information before
merging, similar to how we handle other metadata (such as vlan tags),
and releasing any state when we are done.
Reported-by: John <john.phillips5@hpe.com>
Fixes: 2e15ea39 ("ip_gre: Add support to collect tunnel metadata.")
Signed-off-by: Jesse Gross <jesse@kernel.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we need to lock all buckets in the connection hashtable we'd attempt to
lock 1024 spinlocks, which is way more preemption levels than supported by
the kernel. Furthermore, this behavior was hidden by checking if lockdep is
enabled, and if it was - use only 8 buckets(!).
Fix this by using a global lock and synchronize all buckets on it when we
need to lock them all. This is pretty heavyweight, but is only done when we
need to resize the hashtable, and that doesn't happen often enough (or at all).
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
vnet_fullcsum() accesses ip_hdr() and transport header to compute
the checksum for IPv4 packets, so these need to be initialized in
skb created in vnet_rx_one().
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marc Dionne discovered a NULL pointer dereference when setting
SO_REUSEPORT on a socket after it is bound.
This patch removes the assumption that at least one socket in the
reuseport group is bound with the SO_REUSEPORT option before other
bind calls occur.
Fixes: e32ea7e74727 ("soreuseport: fast reuseport UDP socket selection")
Reported-by: Marc Dionne <marc.c.dionne@gmail.com>
Signed-off-by: Craig Gallek <kraig@google.com>
Tested-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Evgeny Cherkashin <Eugene.Crosser@ru.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using a combination of connected and un-connected sockets, Dmitry
was able to trigger soft lockups with his fuzzer.
The problem is that sockets in the SO_REUSEPORT array might have
different scores.
Right after sk2=socket(), setsockopt(sk2,...,SO_REUSEPORT, on) and
bind(sk2, ...), but _before_ the connect(sk2) is done, sk2 is added into
the soreuseport array, with a score which is smaller than the score of
first socket sk1 found in hash table (I am speaking of the regular UDP
hash table), if sk1 had the connect() done, giving a +8 to its score.
hash bucket [X] -> sk1 -> sk2 -> NULL
sk1 score = 14 (because it did a connect())
sk2 score = 6
SO_REUSEPORT fast selection is an optimization. If it turns out the
score of the selected socket does not match score of first socket, just
fallback to old SO_REUSEPORT logic instead of trying to be too smart.
Normal SO_REUSEPORT users do not mix different kind of sockets, as this
mechanism is used for load balance traffic.
Fixes: e32ea7e74727 ("soreuseport: fast reuseport UDP socket selection")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Craig Gallek <kraigatgoog@gmail.com>
Acked-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This isn't used anywhere, so delete it.
Looks like the last usage (in x86-specific code) was removed by Tejun
in 2011 in commit bd6709a91a59 ("x86, NUMA: Make 32bit use common NUMA
init path").
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
|
|
This ensures that we always notify context tracking that we
have exited from user space no matter how we enter the kernel.
It is similar to how arm64 handles context tracking, for example.
This allows the removal of all the exception_enter() calls that
were added in commit 49e4e15619cd ("tile: support CONTEXT_TRACKING and
thus NOHZ_FULL").
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
|
|
This flag value is saved in ptregs and used to decide whether
to disable irqs when returning from the kernel. Commit 1168df528fe4
("tile: don't assume user privilege is zero") performed a bad
merge from some KVM-enabled code that had not yet been upstreamed.
The only issue with the old code is that we will read the interrupt
mask in more conditions than we need to (e.g., coming from user
space when user space has the Interrupt Critical Section bit set, or
coming from a guest kernel), which is a slow multi-cycle operation.
This change saves those few cycles in the common case.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
|
|
Missing parentheses could cause an argument of the form
"integer + pointer" to get cast to "(long)integer + pointer"
and remain a pointer type, causing compiler warnings.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
|
|
The warning occurs in setup.c, where it is known that it can't be
a problem, but it's still a good idea to silence the warning.
The onstack array is converted from an s32 to a u8, which still
is plenty of range for the values being managed there.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
|
|
This information is easily available in the backtrace data and can
be helpful when trying to figure out the backtrace, particularly
if we're early in kernel entry or late in kernel exit.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
|
|
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
|
|
This change is a prerequisite change for TASK_ISOLATION but also
stands on its own for readability and maintainability. The existing
tile do_work_pending() was called in a loop from assembly on
the slow path; this change moves the loop into C code as well.
For the x86 version see commit c5c46f59e4e7 ("x86/entry: Add new,
comprehensible entry and exit handlers written in C").
This change exposes a pre-existing bug on the older tilepro platform;
the singlestep processing is done last, but on tilepro (unlike tilegx)
we enable interrupts while doing that processing, so we could in
theory miss a signal or other asynchronous event. A future change
could fix this by breaking the singlestep work into a "prepare"
step done in the main loop, and a "trigger" step done after exiting
the loop. Since this change is intended as purely a restructuring
change, we call out the bug explicitly now, but don't yet fix it.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
|
|
The Kconfig for this support is currently:
config IDEPCI_PCIBUS_ORDER
bool "Probe IDE PCI devices in the PCI bus order (DEPRECATED)"
...meaning that it currently is not being built as a module by anyone.
Lets change the initcall to be the equivalent device_initcall, so that
when reading the driver code, there is no doubt it is builtin-only.
Unlike other similar changes, we leave the module.h header to be
included since this code interacts with other drivers and needs to
know what a struct module is.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-ide@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ide_dma_ops structures are never modified, so declare these as const,
as is already done for the others.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Back in the day we used to just say this code was root only so it was
ok that the bounds checking was sloppy. These days it annoys static
checkers so we fix it.
In the original code "c > INT_MAX" was never true since "c" was an int.
I am not sure what was intended so I left it alone. But because I made
"c" unsigned it means we don't have a warning any more.
The second warning is that we cap "i" but allow negatives leading to an
underflow of the ide_disks_chs[] array. The third set of warnings is
because these values come from the user and we cap most of the upper
bounds but allow negative values. Negative cylinders doesn't make
sense.
drivers/ide/ide.c:262 ide_set_disk_chs() warn: impossible condition '(c > ((~0 >> 1))) => (s32min-s32max > s32max)'
drivers/ide/ide.c:270 ide_set_disk_chs() warn: check 'ide_disks_chs[i]' for negative offsets 'i' = s32min. extra = 's32min-19'
drivers/ide/ide.c:271 ide_set_disk_chs() warn: no lower bound on 'h'
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was seen that defective configurations of openvswitch could overwrite
the STACK_END_MAGIC and cause a hard crash of the kernel because of too
many recursions within ovs.
This problem arises due to the high stack usage of openvswitch. The rest
of the kernel is fine with the current limit of 10 (RECURSION_LIMIT).
We use the already existing recursion counter in ovs_execute_actions to
implement an upper bound of 5 recursions.
Cc: Pravin Shelar <pshelar@ovn.org>
Cc: Simon Horman <simon.horman@netronome.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can't be within an RCU read-side critical section when deleting
VLANs, as underlying drivers might sleep during the hardware operation.
Therefore, replace the RCU critical section with a mutex. This is
consistent with team_vlan_rx_add_vid.
Fixes: 3d249d4ca7d0 ("net: introduce ethernet teaming device")
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current upstreaming code fails to set the tso_mode register
when initilizes, when processes large size packets, the default 4 bd is
not enough, so this patch initilizes it and set the default value to 8 bds
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With gcc < 4.3 __UNIQUE_ID does not create unique ids with the macro
BRCMF_FW_NVRAM_DEF. Fix this by removing the MODULE_FIRMWARE instance
for the nvram file. This file is not in linux-firmware repo so it may
not be needed anyway. Otherwise consider this as a temporary fix.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arend van Spriel <aspriel@gmail.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unregister the chain type and return error, otherwise this leaks the
subscription to the netdevice notifier call chain.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
In case MSS option is added in TCP options, skb length increases by 4.
IPv6 needs to update skb->csum if skb has CHECKSUM_COMPLETE,
otherwise kernel complains loudly in netdev_rx_csum_fault() with a
stack dump.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
As seen by Julia, the initial allocation memory is not checked anymore
after commit "video: fbdev: pxafb: initial devicetree conversion".
Introduce back the removed test.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
Johannes Berg
Russell King
Martin Roth
Thomas Egerer
Marcelo Ricardo Leitner
Arnd Bergmann
Hannes Frederic Sowa
Iyappan Subramanian
Eric Dumazet
Johannes Weiner
Teresa Remmet
Jisheng Zhang
yankejian
Jesse Gross
Florian Fainelli
Sudip Mukherjee
Xin Long
Manfred Rudigier
Sasha Levin
Sowmini Varadhan
Craig Gallek
Ursula Braun
Chris Metcalf
Fengguang Wu
Paul Gortmaker
Julia Lawall
Dan Carpenter
Ido Schimmel
huangdaode
Arend van Spriel
Pablo Neira Ayuso
Robert Jarzmik