aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/i2c (follow)
AgeCommit message (Collapse)AuthorFilesLines
2015-08-01i2c: fix leaked device refcount on of_find_i2c_* error pathVladimir Zapolskiy1-6/+14
If of_find_i2c_device_by_node() or of_find_i2c_adapter_by_node() find a device by node, but its type does not match, a reference to that device is still held. This change fixes the problem. Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-07-31i2c: Fix typo in i2c-bfin-twi.cMasanari Iida1-2/+2
This patch fix some typos found in a printk message and MODULE_DESCRIPTION. Signed-off-by: Masanari Iida <standby24x7@gmail.com> Acked-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-07-31i2c: omap: fix bus recovery setupJan Luebbe1-0/+11
At least on the AM335x, enabling OMAP_I2C_SYSTEST_ST_EN is not enough to allow direct access to the SCL and SDA pins. In addition to ST_EN, we need to set the TMODE to 0b11 (Loop back & SDA/SCL IO mode select). Also, as the reset values of SCL_O and SDA_O are 0 (which means "drive low level"), we need to set them to 1 (which means "high-impedance") to avoid unwanted changes on the pins. As a precaution, reset all these bits to their default values after recovery is complete. Signed-off-by: Jan Luebbe <jlu@pengutronix.de> Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-07-31i2c: core: only use set_scl for bus recovery after calling prepare_recoveryJan Luebbe1-1/+3
Using set_scl may be ineffective before calling the driver specific prepare_recovery callback, which might change into a test mode. So instead of setting SCL in i2c_generic_scl_recovery, move it to i2c_generic_recovery (after the optional prepare_recovery). Signed-off-by: Jan Luebbe <jlu@pengutronix.de> Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-07-31i2c: slave eeprom: clean up sysfs bin attribute read()/write()Vladimir Zapolskiy1-6/+0
The change removes redundant sysfs binary file boundary checks, since this task is already done on caller side in fs/sysfs/file.c Note, on file size overflow read() now returns 0, and this is a correct and expected EOF notification according to POSIX. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-07-09i2c: Mark instantiated device nodes with OF_POPULATEPantelis Antoniou1-1/+15
Mark (and unmark) device nodes with the POPULATE flag as appropriate. This is required to avoid multi probing when using I2C and device overlays containing a mux. This patch is also more careful with the release of the adapter device which caused a deadlock with muxes, and does not break the build on !OF since the node flag accessors are not defined then. Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-07-09i2c: jz4780: Fix return value if probe failsAxel Lin1-7/+8
Current code returns 0 if fails to read clock-frequency DT property, fix it. Also add checking return value of clk_prepare_enable and propagate return value of devm_request_irq. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-07-09i2c: xgene-slimpro: Fix missing mbox_free_channel call in probe error pathAxel Lin1-0/+1
Free requested mailbox channel before return error. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-07-09i2c: I2C_MT65XX should depend on HAS_DMAGeert Uytterhoeven1-0/+1
If NO_DMA=y: ERROR: "dma_unmap_single" [drivers/i2c/busses/i2c-mt65xx.ko] undefined! ERROR: "dma_mapping_error" [drivers/i2c/busses/i2c-mt65xx.ko] undefined! ERROR: "dma_map_single" [drivers/i2c/busses/i2c-mt65xx.ko] undefined! Add a dependency on HAS_DMA to fix this. Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-26Merge tag 'char-misc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-miscLinus Torvalds1-5/+33
Pull char/misc driver updates from Greg KH: "Here's the big char/misc driver pull request for 4.2-rc1. Lots of mei, extcon, coresight, uio, mic, and other driver updates in here. Full details in the shortlog. All of these have been in linux-next for some time with no reported problems" * tag 'char-misc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (176 commits) mei: me: wait for power gating exit confirmation mei: reset flow control on the last client disconnection MAINTAINERS: mei: add mei_cl_bus.h to maintained file list misc: sram: sort and clean up included headers misc: sram: move reserved block logic out of probe function misc: sram: add private struct device and virt_base members misc: sram: report correct SRAM pool size misc: sram: bump error message level on unclean driver unbinding misc: sram: fix device node reference leak on error misc: sram: fix enabled clock leak on error path misc: mic: Fix reported static checker warning misc: mic: Fix randconfig build error by including errno.h uio: pruss: Drop depends on ARCH_DAVINCI_DA850 from config uio: pruss: Add CONFIG_HAS_IOMEM dependence uio: pruss: Include <linux/sizes.h> extcon: Redefine the unique id of supported external connectors without 'enum extcon' type char:xilinx_hwicap:buffer_icap - change 1/0 to true/false for bool type variable in function buffer_icap_set_configuration(). Drivers: hv: vmbus: Allocate ring buffer memory in NUMA aware fashion parport: check exclusive access before register w1: use correct lock on error in w1_seq_show() ...
2015-06-25Merge branch 'i2c/for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linuxLinus Torvalds28-154/+2602
Pull i2c updates from Wolfram Sang: "Highlights: - new drivers for Mediatek I2C, APM X-Gene, Broadcom Settop - major updates to at91, davinci - bugfixes to the mux infrastructure when dealing with the new quirk mechanism - more users for the bus recovery feature - further improvements to the slave framework Plus the usual bunch of smaller driver and core improvements and fixes. There is one patch removing old code from an ARM platform. This has been acked by the sh_mobile maintainer Simon Horman" * 'i2c/for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (48 commits) i2c: busses: i2c-bcm2835: limits cdiv to allowed values i2c: sh_mobile: use proper type for timeout i2c: sh_mobile: use adapter default for timeout i2c: rcar: use proper type for timeout i2c: rcar: use adapter default for timeout i2c: designware: Make sure the device is suspended before disabling runtime PM i2c: tegra: apply size limit quirk i2c: tegra: don't advertise SMBUS_QUICK i2c: octeon: remove unused signal handling i2c: davinci: Optimize SCL generation i2c: mux: pca954x: Use __i2c_transfer because of quirks i2c: mux: Use __i2c_transfer() instead of calling parent's master_xfer() i2c: use parent adapter quirks in mux i2c: bcm2835: clear reserved bits in S-Register ARM: shmobile: r8a7740: remove I2C errata handling i2c: sh_mobile: add errata workaround i2c: at91: fix code checker warnings i2c: busses: xgene-slimpro: fix incorrect __init declation for probe i2c: davinci: Avoid sending to own address i2c: davinci: Refactor i2c_davinci_wait_bus_not_busy() ...
2015-06-23Merge tag 'mfd-for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfdLinus Torvalds2-16/+31
Pull MFD updates from Lee Jones: "Changes to existing drivers: - Constify structures; throughout the subsystem - Move support to DT in; cros_ec - DT changes and documentation; cros-ec, max77693, max77686, arizona, da9063 - ACPI changes and documentation; mfd-core - Use different platform specific API in; cros_ec_*, arizona-core - Remove unused parent field from; cros_ec_i2c - Add wake-up/reset delay in; cross_ec_spi, arizona-core - Staticise structures/functions in; cros_ec - Remove redundant code; arizona-core, max77686 - Bugfix; twl4030-power - Allow compile test; aat2870, tps65910 - MAINTAINERS adaptions; samsung, syscon - Resource Management (devm_*); arizona-core - Refactor Reset code; arizona-core - Insist on at least one full boot; arizona-core - Trivial formatting; arizona-core - Add low-power-sleep; arizona-core - IRQ ONESHOT changes; twl4030-irq, mc13xxx-core, wm831x-auxadc, htc-i2cpld, wm8350-core, ab8500-debugfs, ab8500-gpadc, si476x-i2c (Re-)moved drivers: - Move protocol helpers out to drivers/platform; cros_ec New drivers/supported devices: - Add support for AXP22x into axp20x - Add support for OnKey into da9063-core - Add support for Pinctrl into mt6397-core - New STMicroelectronics LPC Watchdog driver - New STMicroelectronics LPC Real-Time Clock driver" * tag 'mfd-for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (59 commits) mfd: lpc_ich: Assign subdevice ids automatically mfd: si476x-i2c: Pass the IRQF_ONESHOT flag mfd: ab8500-gpadc: Pass the IRQF_ONESHOT flag mfd: ab8500-debugfs: Pass the IRQF_ONESHOT flag mfd: wm8350-core: Pass the IRQF_ONESHOT flag mfd: htc-i2cpld: Pass the IRQF_ONESHOT flag mfd: wm831x-auxadc: Pass the IRQF_ONESHOT flag mfd: mc13xxx-core: Pass the IRQF_ONESHOT flag mfd: twl4030-irq: Pass the IRQF_ONESHOT flag mfd: mt6397-core: Add GPIO sub-module support mfd: arizona: Add convience defines for micd_rate/micd_bias_starttime mfd: dt: Add bindings for DA9063 OnKey mfd: da9063: Add support for OnKey driver mfd: arizona: Fix incorrect Makefile conditionals mfd: arizona: Add stub for wm5102_patch() mfd: Check ACPI device companion before checking resources Documentation: Add WM8998/WM1814 device tree bindings mfd: arizona: Split INx_MODE into two fields mfd: wm5110: Add delay before releasing reset line mfd: arizona: Add better support for system suspend ...
2015-06-23Merge tag 'mmc-v4.2' of git://git.linaro.org/people/ulf.hansson/mmcLinus Torvalds1-2/+2
Pull MMC updates from Ulf Hansson: "Here are the changes for MMC for v4.2. MMC core: - Fix an error path in the mmc block layer - Fix PM domain attachment for the SDIO bus - Add support for driver strength selection - Increase a delay to let voltage stabilize - Add support for disabling write-protect detection - Add facility to support re-tuning - Re-tune and retry in the recovery path - Add reset option for SDIO - Consolidations and clean-ups MMC host: - Add Mediatek MMC driver - Constify platform_device_id for a couple of hosts - Fix modalias to make module auto-loading work for a couple of hosts - sdhci: Add support for sdhci-arasan4.9a - sdhci: Fix low memory corruption - sdhci: Restore behavior while creating OCR mask - sdhci: Add a callback to select drive strength - sdhci: Fix driver type B and D handling - sdhci: Add support for drive strength selection for SPT - sdhci: Enable HS400 for some Intel host controllers - sdhci: Convert to use the new re-tuning facility - sdhci: Various minor fixes and clean-ups - dw_mmc: Add support for hi6220 - dw_mmc: Use core to handle absent write protect line - dw_mmc: Add support to switch voltage - tmio: Some fixes and modernizations - sh_mmcif: Improve clock rate calculation" * tag 'mmc-v4.2' of git://git.linaro.org/people/ulf.hansson/mmc: (98 commits) mmc: queue: prevent soft lockups on PREEMPT=n mmc: mediatek: Add PM support for MMC driver mmc: mediatek: Add Mediatek MMC driver mmc: dt-bindings: add Mediatek MMC bindings mmc: card: Fixup request missing in mmc_blk_issue_rw_rq mmc: sdhci: fix low memory corruption mmc: sdhci-pci: Change AMD SDHCI quirk application scope i2c-piix4: Use Macro for AMD CZ SMBus device ID pci_ids: Add AMD KERNCZ device ID support mmc: queue: use swap() in mmc_queue_thread() mmc: dw_mmc: insmod followed by rmmod will hung for eMMC mmc: sdhci: Restore behavior while creating OCR mask mmc: sdhci-pxav3: fix device wakeup initialization mmc: core: Attach PM domain prior probing of SDIO func driver mmc: core: Remove redundant ->power_restore() callback for SD mmc: core: Remove redundant ->power_restore() callback for MMC mmc: sdhci-bcm2835: Actually enable the clock mmc: sdhci-bcm2835: Clean up platform allocations if sdhci init fails. mmc: sdhci-of-esdhc: enable interrupt mode to detect card mmc: sdhci-esdhc-imx: add quirk SDHCI_QUIRK2_BROKEN_HS200 for imx6qdl ...
2015-06-23Merge tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpioLinus Torvalds1-4/+8
Pull gpio updates from Linus Walleij: "This is the big bulk of GPIO changes queued for the v4.2 kernel series: - a big set of cleanups to the aged sysfs interface from Johan Hovold. To get these in, v4.1-rc3 was merged into the tree as the first patch in that series had to go into stable. This makes the locking much more fine-grained (get rid of the "big GPIO lock(s)" and store states in the GPIO descriptors. - rename gpiod_[g|s]et_array() to gpiod_[g|s]et_array_value() to avoid confusions. - New drivers for: * NXP LPC18xx (currently LPC1850) * NetLogic XLP * Broadcom STB SoC's * Axis ETRAXFS * Zynq Ultrascale+ (subdriver) - ACPI: * make it possible to retrieve GpioInt resources from a GPIO device using acpi_dev_gpio_irq_get() * merge some dependent I2C changes exploiting this. * support the ARM X-Gene GPIO standby driver. - make it possible for the generic GPIO driver to read back the value set registers to reflect current status. - loads of OMAP IRQ handling fixes. - incremental improvements to Kona, max732x, OMAP, MXC, RCAR, PCA953x, STP-XWAY, PCF857x, Crystalcove, TB10x. - janitorial (constification, checkpatch cleanups)" * tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits) gpio: Fix checkpatch.pl issues gpio: pcf857x: handle only enabled irqs gpio / ACPI: Return -EPROBE_DEFER if the gpiochip was not found GPIO / ACPI: export acpi_gpiochip_request(free)_interrupts for module use gpio: improve error reporting on own descriptors gpio: promote own request failure to pr_err() gpio: Added support to Zynq Ultrascale+ MPSoC gpio: add ETRAXFS GPIO driver fix documentation after renaming gpiod_set_array to gpiod_set_array_value gpio: Add GPIO support for Broadcom STB SoCs gpio: xgene: add ACPI support for APM X-Gene GPIO standby driver gpio: tb10x: Drop unneeded free_irq() call gpio: crystalcove: set IRQCHIP_SKIP_SET_WAKE for the irqchip gpio: stp-xway: Use the of_property_read_u32 helper gpio: pcf857x: Check for irq_set_irq_wake() failures gpio-stp-xway: Fix enabling the highest bit of the PHY LEDs gpio: Prevent an integer overflow in the pca953x driver gpio: omap: rework omap_gpio_irq_startup to handle current pin state properly gpio: omap: rework omap_gpio_request to touch only gpio specific registers gpio: omap: rework omap_x_irq_shutdown to touch only irqs specific registers ...
2015-06-23i2c: busses: i2c-bcm2835: limits cdiv to allowed valuesSilvan Wicki1-0/+8
Checks if the cdiv value is in between min (0x2) and max (0xFFFE) supported values by the bcm2835. If not, it returns -ENODEV. See page 33/34 of BCM2835-ARM-Peripherals.pdf for the DIV register. https://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf Signed-off-by: Silvan Wicki <linux_wi@tinag.ch> [wsa: resolved a merge conflict] Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-23i2c: sh_mobile: use proper type for timeoutWolfram Sang1-3/+4
wait_event_timeout returns long, not int. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-23i2c: sh_mobile: use adapter default for timeoutWolfram Sang1-1/+1
5 seconds is a very large timeout, and it is hardcoded. Use the default timeout from 'struct adapter' which is 1 second. It can also be modified from userspace for specific workloads via i2c-dev. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-23i2c: rcar: use proper type for timeoutWolfram Sang1-1/+2
wait_event_timeout returns long, not int. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-23i2c: rcar: use adapter default for timeoutWolfram Sang1-1/+1
5 seconds is a very large timeout, and it is hardcoded. Use the default timeout from 'struct adapter' which is 1 second. It can also be modified from userspace for specific workloads via i2c-dev. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-21i2c: designware: Make sure the device is suspended before disabling runtime PMMika Westerberg1-1/+2
The driver calls pm_runtime_put() right before pm_runtime_disable() in its ->remove() hook to make sure clock is gated etc. However, it turns out that pm_runtime_put() only calls ->idle() hook without actually suspending anything. The following pm_runtime_disable() will prevent the driver from suspending thus leaving it "active". It is better to suspend the device synchronously to make sure it is actually suspended before disabling runtime PM from it. While there, undo call to pm_runtime_use_autosuspend(). Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-21i2c: tegra: apply size limit quirkWolfram Sang1-0/+7
payload_size is a 12 bit field in the HW register, so add a limit for this size. That way we gracefully reject the message beforehand instead of generating an OOPS while transferring. Verified using some older Tegra2 documentation and a more recent Jetson TK1 board. Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
2015-06-21i2c: tegra: don't advertise SMBUS_QUICKWolfram Sang1-2/+2
This HW cannot send 0-byte-length messages and the driver discards them. So, we should not advertise SMBUS_QUICK. Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-17i2c: octeon: remove unused signal handlingNicholas Mc Guire1-5/+2
'commit 2637e5fd232d ("i2c: octeon: Fix i2c fail problem when a process is terminated by a signal")' removed the wait_event_interruptible_timeout to prevent half/mixed i2c messages from being sent/recievd but forgot to drop the signal handling case in the return handling. This just removes this dead code. While at it the return variable is adjusted to the type expected. Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-17i2c: davinci: Optimize SCL generationAlexander Sverdlin1-3/+24
There are several cases where current clock configuration algorithm produces not optimal results: - truncation in "clk" calculation leads to the fact that actual BUS frequency will be always higher than spec except two exact module frequences 8MHz and 12MHz in the whole 7-12MHz range of permitted frequences - driver configures SCL HIGH to LOW ratio always 1 to 1 and this doesn't work well in 400kHz case, namely minimum time of LOW state (according to I2C Spec 2.1) 1.3us will not be fulfilled. HIGH to LOW ratio 1 to 2 would be more approriate here. Signed-off-by: Michael Lawnick <michael.lawnick@nokia.com> Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-17i2c: mux: pca954x: Use __i2c_transfer because of quirksAlexander Sverdlin2-3/+3
pca9541 and pca954x are calling master_xfer() of the parent adapter directly thus bypassing the quirks checks of the adapter. Use __i2c_transfer() instead. Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Tested-by: Łukasz Gemborowski <lukasz.gemborowski@nokia.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Jisheng Zhang <jszhang@marvell.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org Fixes: b7f625840267b1 ("i2c: add quirk checks to core")
2015-06-17i2c: mux: Use __i2c_transfer() instead of calling parent's master_xfer()Alexander Sverdlin1-1/+1
Newly introduced quirks infrastructure doesn't work for the devices behind MUXes because MUX's master_xfer() calls parent's master_xfer() directly without checking the quirks. Instead of duplicating check code in MUX just call __i2c_transfer() instead. This has a side effect on tracing (messages will appear on both MUX bus and parent bus), but maybe that's not bad at the end. Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Tested-by: Łukasz Gemborowski <lukasz.gemborowski@nokia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org Fixes: b7f625840267b1 ("i2c: add quirk checks to core")
2015-06-17i2c: use parent adapter quirks in muxAlexander Sverdlin1-0/+1
Inherit parent adapter quirks in MUX in case the devices on the multiplexed buses are interested in the adapter limitations. Signed-off-by: Łukasz Gemborowski <lukasz.gemborowski@nokia.com> Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org Fixes: b7f625840267b1 ("i2c: add quirk checks to core")
2015-06-17i2c: bcm2835: clear reserved bits in S-RegisterSilvan Wicki1-0/+3
The datasheet mentions on page 31 that the bits 10-31 must be read as don't care and written as 0. https://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf We cannot guarantee that we read bits 10-31 as always 0 (because the datasheet says read as don't care). We clear the bits with a bitmask to prevent writing back unknown data at the reserved bits. Signed-off-by: Silvan Wicki <linux_wi@tinag.ch> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-17i2c: sh_mobile: add errata workaroundWolfram Sang1-0/+40
This used to be in platform init code. We want it to do in the driver now. This is basically a code move and a new compatible added. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Acked-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-16i2c-piix4: Use Macro for AMD CZ SMBus device IDVincent Wan1-2/+2
Change AMD CZ SMBUS device ID from 0x790b to use Macro definition Signed-off-by: Wan ZongShun <Vincent.Wan@amd.com> Acked-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-06-15mfd: cros_ec: Move protocol helpers out of the MFD driverJavier Martinez Canillas1-1/+1
The MFD driver should only have the logic to instantiate its child devices and setup any shared resources that will be used by the subdevices drivers. The cros_ec MFD is more complex than expected since it also has helpers to communicate with the EC. So the driver will only get more bigger as other protocols are supported in the future. So move the communication protocol helpers to its own driver as drivers/platform/chrome/cros_ec_proto.c. Suggested-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Tested-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Lee Jones <lee.jones@linaro.org> Acked-by: Olof Johansson <olof@lixom.net> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-15mfd: cros_ec: Use a zero-length array for command dataJavier Martinez Canillas1-15/+30
Commit 1b84f2a4cd4a ("mfd: cros_ec: Use fixed size arrays to transfer data with the EC") modified the struct cros_ec_command fields to not use pointers for the input and output buffers and use fixed length arrays instead. This change was made because the cros_ec ioctl API uses that struct cros_ec_command to allow user-space to send commands to the EC and to get data from the EC. So using pointers made the API not 64-bit safe. Unfortunately this approach was not flexible enough for all the use-cases since there may be a need to send larger commands on newer versions of the EC command protocol. So to avoid to choose a constant length that it may be too big for most commands and thus wasting memory and CPU cycles on copy from and to user-space or having a size that is too small for some big commands, use a zero-length array that is both 64-bit safe and flexible. The same buffer is used for both output and input data so the maximum of these values should be used to allocate it. Suggested-by: Gwendal Grignou <gwendal@chromium.org> Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Tested-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Lee Jones <lee.jones@linaro.org> Acked-by: Olof Johansson <olof@lixom.net> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-11i2c: at91: fix code checker warningsCyrille Pitchen1-3/+3
buf_len is a size_t, so unsigned, but was tested with '<= 0'. Reported-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-10i2c: busses: xgene-slimpro: fix incorrect __init declation for probeFeng Kan1-1/+1
Fix section mismatch error during kernel build for xgene_slimpro_i2c_probe function. It was incorrectly defined with __init declaration. Signed-off-by: Feng Kan <fkan@apm.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-10i2c: davinci: Avoid sending to own addressAlexander Sverdlin1-3/+8
Sending a message to own address locks the controller up in very bizarre state, it behaves as slave even if MDR register clearly states master. The controller remains in this state until reset. To avoid unnecessary timeouts simply avoid sending to own address. The controller cannot do this any way. Also, do not enable AAS IRQ, as the slave mode is not supported by the driver and the only possibility to trigger this IRQ is to send to own address. Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-10i2c: davinci: Refactor i2c_davinci_wait_bus_not_busy()Alexander Sverdlin1-23/+19
There are several problems in the function: - "to_cnt" variable does nothing - schedule_timeout() call without setting current state does nothing - "allow_sleep" parameter is not really used Refactor the function so that it really tries to wait. In case of timeout try to recover the bus. Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-10i2c: brcmstb: Add Broadcom settop SoC i2c controller driverKamal Dasu3-0/+705
Adding support for i2c controller driver for Broadcom settop SoCs. Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com> [wsa: removed superfluous owner in platform_driver] Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-10i2c: at91: add support to FIFOsCyrille Pitchen1-17/+130
When FIFOs are available and enabled, the driver now configures the Atmel eXtended DMA Controller to perform word accesses instead of byte accesses when possible. The actual access width depends on the size of the buffer to transmit. To enable FIFO support the "atmel,fifo-size" property must be set properly in the I2C controller node of the device tree. Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-10i2c: at91: print hardware versionCyrille Pitchen1-1/+4
The probe() function now prints the hardware version of the I2C controller. Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> [wsa: s/version/hw version/] for clarity] Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-10i2c: at91: add support for new alternative command modeCyrille Pitchen1-20/+101
The alternative command mode was introduced to simplify the transmission of STOP conditions and to solve timing and latency issues around them. This mode relies on a new register, the Alternative Command Register, which must be set at the same time as the Master Mode Register. This new register was designed to allow simple setup of basic combined transactions built from up to two unitary transactions. Indeed, the ACR is split into two areas, which describe one unitary transaction each. Each area is filled with Data Length 8bit counter, a Direction and a PEC Request bit. The PEC bit is only used in SMBus mode and is not supported by this driver yet. Also when using alternative command mode, the MREAD bit from the Master Mode Register is ignored. Instead the Direction bits from ACR are used to setup the direction, read or write, of each unitary transaction. Finally the 8bit counters must filled with the data length of their respective transaction. Then if only one transaction is to be used, the data length of the second one must be set to zero. At the moment, this driver uses only the first transaction. In addition to MMR and ACR, the Control Register also need to be written to enable the alternative command mode. That's the purpose of its ACMEN bit, which stands for Alternative Command Mode Enable. Note that the alternative command mode is compatible with the use of the Internal Address Register. So combined transactions for eeprom read are actually implemented with the Internal Address Register. This register is written with up to 3 bytes, which are the internal address sent to the slave through the first write transaction. Then the first area of the ACR describe the write transaction to follow, which carries the data to be read from the eeprom. The second area of the ACR is not used so its Data Length 8bit counter is cleared. For each byte sent or received by the device, the Data Length 8bit counter is decremented. When it reaches 0, a STOP condition is automatically sent. Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-10i2c: at91: use BIT() macro to define register bitsCyrille Pitchen1-14/+15
This patch just fixes typo before applying later patches which will use register bits with index above 16. Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-10i2c: at91: fix a race condition when using the DMA controllerCyrille Pitchen1-17/+53
For TX transactions, the TXCOMP bit in the Status Register is cleared when the first data is written into the Transmit Holding Register. In the lines from at91_do_twi_transfer(): at91_twi_write_data_dma(dev); at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_TXCOMP); the TXCOMP interrupt may be enabled before the DMA controller has actually started to write into the THR. In such a case, the TXCOMP bit is still set into the Status Register so the interrupt is triggered immediately. The driver understands that a transaction completion has occurred but this transaction hasn't started yet. Hence the TXCOMP interrupt is no longer enabled by at91_do_twi_transfer() but instead by at91_twi_write_data_dma_callback(). Also, the TXCOMP bit in the Status Register in not a clear on read flag but a snapshot of the transmission state at the time the Status Register is read. When a NACK error is dectected by the I2C controller, the TXCOMP, NACK and TXRDY bits are set together to 1 in the SR. If enabled, the TXCOMP interrupt is triggered at the same time. Also setting the TXRDY to 1 triggers the DMA controller to write the next data into the THR. Such a write resets the TXCOMP bit to 0 in the SR. So depending on when the interrupt handler reads the SR, it may fail to detect the NACK error if it relies on the TXCOMP bit. The NACK bit and its interrupt should be used instead. For RX transactions, the TXCOMP bit in the Status Register is cleared when the START bit is set into the Control Register. However to unify the management of the TXCOMP bit when the DMA controller is used, the TXCOMP interrupt is now enabled by the DMA callbacks for both TX and RX transfers. Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Cc: stable@vger.kernel.org #3.10 and later Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-03i2c: iproc: Add suspend/resume supportRay Jui1-0/+57
Add suspend/resume support to the Broadcom iProc I2C driver Signed-off-by: Ray Jui <rjui@broadcom.com> Reviewed-by: Scott Branden <sbranden@broadcom.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-03i2c: designware: Avoid unnecessary resuming during system suspendJisheng Zhang1-4/+28
Commit 1fc2fe204cb9 ("i2c: designware: Add runtime PM hooks") adds runtime pm support using the same ops for system pm and runtime pm. When suspend to ram, the i2c host may have been runtime suspended, thus i2c_dw_disable() hangs. Previously, I fixed this issue by separating ops for system pm and runtime pm, then in the system suspend/resume path, runtime pm apis are used to ensure the device is at correct state. But as Mika Westerberg pointed out: it sounds a bit silly to resume the device just because you want to call i2c_dw_disable() for it before suspending again. He then suggested an elegant solution which keeps the device runtime suspended during system suspend with the help of 'dev->power.direct_complete'. This patch adopted this solution, and in fact Mika provided the main code. Signed-off-by: Jisheng Zhang <jszhang@marvell.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-03i2c: axxia: Add bus recovery functionalityAlexander Sverdlin1-0/+41
Use recovery framework and implement bus recovery using "Bus Monitor" register. Tests show that shortening SDA to GND results in "completion" timeout with "BUSY" bit still set, so initiate recovery in this case. Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-03i2c: core: Reduce stack size of acpi_i2c_space_handler()Jarkko Nikula1-16/+21
sizeof(struct i2c_client) is 1088 bytes on a CONFIG_X86_64=y build and produces following warning when CONFIG_FRAME_WARN is set to 1024: drivers/i2c/i2c-core.c: In function ‘acpi_i2c_space_handler’: drivers/i2c/i2c-core.c:367:1: warning: the frame size of 1152 bytes is larger than 1024 bytes [-Wframe-larger-than=] This is not critical given that kernel stack is 16 kB on x86_64 but lets reduce the stack usage by allocating the struct i2c_client from the heap. Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-01i2c: smbus: fix typo in commetShailendra Verma1-1/+1
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-01i2c: algo-pca: fix typo in commentShailendra Verma1-1/+1
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-01i2c: core: fix typo in commentShailendra Verma1-1/+1
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-01I2C: mediatek: Add driver for MediaTek MT8173 I2C controllerEddie Huang1-29/+74
Add mediatek MT8173 I2C controller driver. Compare to I2C controller of earlier mediatek SoC, MT8173 fix write-then-read limitation, and also increase message size to 64kb. Signed-off-by: Xudong Chen <xudong.chen@mediatek.com> Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com> Signed-off-by: Eddie Huang <eddie.huang@mediatek.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.