| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
|
|
Pull MFD updates from Lee Jones:
"Changes to the core:
- Honour PLATFORM_DEVID_NONE and PLATFORM_DEVID_AUTO dev IDs
Changes to existing drivers:
- IRQ additions/fixes; axp20x, da9063-core
- Code simplification; i2c-dln2
- Regmap additions/fixes; max77693
- Error checking/handling improvements; dln2, db8500-prcmu
- Bug fixes; dln2, wm8350-core
- DT support/documentation; max77693, max77686, tps65217, twl4030-power,
gpio-tc3589x
- Decouple syscon interface from platform devices
- Use MFD hotplug registration; rtsx_usb, viperboard, hid-sensor-hub
- Regulator fixups; sec-core
- Power Management additions/fixes; rts5227, tc6393xb
- Remove relic/redundant code; ab8500-sysctrl, lpc_sch, max77693-private
- Clean-up/coding style changes; tps65090
- Clk additions/fixes; tc6393xb, tc6387xb, t7l66xb
- Add USB-SPI support; dln2
- Trivial changes; max14577, arizona-spi, lpc_sch, wm8997-tables, wm5102-tables
wm5110-tables, axp20x, atmel-hlcdc, rtsx_pci
New drivers/supported devices:
- axp288 PMIC support added to axp20x
- s2mps13 support added to sec-core
- New support for Diolan DLN-2
- New support for atmel-hlcdc"
* tag 'mfd-for-linus-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (55 commits)
mfd: rtsx: Add func to split u32 into register
mfd: atmel-hlcdc: Add Kconfig option description and name
mfd: da9063: Get irq base dynamically before registering device
mfd: max14577: Fix obvious typo in company name in copyright
mfd: axp20x: Constify axp20x_acpi_match and rid unused warning
mfd: t7l66xb: prepare/unprepare clocks
mfd: tc6387xb: prepare/unprepare clocks
mfd: dln2: add support for USB-SPI module
mfd: wm5110: Add missing registers for AIF2 channels 3-6
mfd: tc3589x: get rid of static base
mfd: arizona: Document HP_CTRL_1L and HP_CTRL_1R registers
mfd: wm8997: Mark INTERRUPT_STATUS_2_MASK as readable
mfd: tc6393xb: Prepare/unprepare clocks
mfd: tps65090: Fix bonkers indenting strategy
mfd: tc6393xb: Fail ohci suspend if full state restore is required
mfd: lpc_sch: Don't call mfd_remove_devices()
mfd: wm8350-core: Fix probable mask then right shift defect
mfd: ab8500-sysctrl: Drop ab8500_restart
mfd: db8500-prcmu: Provide sane error path values
mfd: db8500-prcmu: Check return of devm_ioremap for error
...
|
|
* pm-runtime: (25 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
PM / Kconfig: Do not select PM directly from Kconfig files
PCI / PM: Drop CONFIG_PM_RUNTIME from the PCI core
...
|
|
* acpi-scan:
ACPI: Add _DEP support to fix battery issue on Asus T100TA
* acpi-pm:
ACPI / sleep: Drain outstanding events after disabling multiple GPEs
ACPI / PM: Fixed a typo in a comment
* acpi-lpss:
dmaengine: dw: enable runtime PM
ACPI / LPSS: introduce a 'proxy' device to power on LPSS for DMA
ACPI / LPSS: allow to use specific PM domain during ->probe()
ACPI / LPSS: add all LPSS devices to the specific power domain
* acpi-processor:
ACPI / cpuidle: avoid assigning signed errno to acpi_status
ACPI / processor: remove unused variabled from acpi_processor_power structure
ACPI / processor: Update the comments in processor.h
|
|
After commit b2b49ccbdd54 (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so some #ifdef blocks
depending on CONFIG_PM_RUNTIME may be dropped now.
Do that in drivers/i2c/busses/i2c-omap.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Cadence I2C controller has bug wherein it generates invalid read transactions
after timeout in master receiver mode. This driver does not use the HW
timeout and this interrupt is disabled but the feature itself cannot be
disabled. Hence, this patch writes the maximum value (0xFF) to this register.
This is one of the workarounds to this bug and it will not avoid the issue
completely but reduces the chances of error.
Signed-off-by: Vishnu Motghare <vishnum@xilinx.com>
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
According to I2C specification the NACK should be handled as follows:
"When SDA remains HIGH during this ninth clock pulse, this is defined as the Not
Acknowledge signal. The master can then generate either a STOP condition to
abort the transfer, or a repeated START condition to start a new transfer."
[I2C spec Rev. 6, 3.1.6: http://www.nxp.com/documents/user_manual/UM10204.pdf]
Currently the Davinci i2c driver interrupts the transfer on receipt of a
NACK but fails to send a STOP in some situations and so makes the bus
stuck until next I2C IP reset (idle/enable).
For example, the issue will happen during SMBus read transfer which
consists from two i2c messages write command/address and read data:
S Slave Address Wr A Command Code A Sr Slave Address Rd A D1..Dn A P
<--- write -----------------------> <--- read --------------------->
The I2C client device will send NACK if it can't recognize "Command Code"
and it's expected from I2C master to generate STP in this case.
But now, Davinci i2C driver will just exit with -EREMOTEIO and STP will
not be generated.
Hence, fix it by generating Stop condition (STP) always when NACK is received.
This patch fixes Davinci I2C in the same way it was done for OMAP I2C
commit cda2109a26eb ("i2c: omap: query STP always when NACK is received").
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: Hein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
The SET_PM_RUNTIME_PM_OPS() and SET_RUNTIME_PM_OPS() macros are
identical except that one of them is not empty for CONFIG_PM set,
while the other one is not empty for CONFIG_PM_RUNTIME set,
respectively.
However, after commit b2b49ccbdd54 (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so one
of these macros is now redundant.
For this reason, replace SET_PM_RUNTIME_PM_OPS() with
SET_RUNTIME_PM_OPS() everywhere and redefine the SET_PM_RUNTIME_PM_OPS
symbol as SET_RUNTIME_PM_OPS in case new code is starting to use the
macro being removed here.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPI 5.0 introduces _DEP (Operation Region Dependencies) to designate
device objects that OSPM should assign a higher priority in start
ordering due to future operation region accesses.
On Asus T100TA, ACPI battery info are read from a I2C slave device via
I2C operation region. Before I2C operation region handler is installed,
battery _STA always returns 0. There is a _DEP method of designating
start order under battery device node.
This patch is to implement _DEP feature to fix battery issue on the
Asus T100TA. Introducing acpi_dep_list and adding dep_unmet count
in struct acpi_device. During ACPI namespace scan, create struct
acpi_dep_data for a valid pair of master (device pointed to by _DEP)/
slave(device with _DEP), record master's and slave's ACPI handle in
it and put it into acpi_dep_list. The dep_unmet count will increase
by one if there is a device under its _DEP. Driver's probe() should
return EPROBE_DEFER when find dep_unmet is larger than 0. When I2C
operation region handler is installed, remove all struct acpi_dep_data
on the acpi_dep_list whose master is pointed to I2C host controller
and decrease slave's dep_unmet. When dep_unmet decreases to 0, all
_DEP conditions are met and then do acpi_bus_attach() for the device
in order to resolve battery _STA issue on the Asus T100TA.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=69011
Tested-by: Jan-Michael Brummer <jan.brummer@tabos.org>
Tested-by: Adam Williamson <adamw@happyassassin.net>
Tested-by: Michael Shigorin <shigorin@gmail.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
commit 6d9939f651419a63e091105663821f9c7d3fec37 (i2c: omap: split out [XR]DR
and [XR]RDY) changed the way how errata i207 (I2C: RDR Flag May Be Incorrectly
Set) get handled. 6d9939f6514 code doesn't correspond to workaround provided by
errata.
According to errata ISR must filter out spurious RDR before data read not after.
ISR must read RXSTAT to get number of bytes available to read. Because RDR
could be set while there could no data in the receive FIFO.
Restored pre 6d9939f6514 way of handling errata.
Found by code review. Real impact haven't seen.
Tested on Beagleboard XM C.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Fixes: 6d9939f651419a63e09110 i2c: omap: split out [XR]DR and [XR]RDY
Tested-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If the Designware core is configured with IC_EMPTYFIFO_HOLD_MASTER_EN
set to zero, allowing the TX FIFO to become empty causes a STOP
condition to be generated on the I2C bus. If the transmit FIFO
threshold is set too high, an erroneous STOP condition can be
generated on long transfers - particularly where the interrupt
latency is extended.
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
commit 1d7afc95946487945cc7f5019b41255b72224b70 (i2c: omap: ack IRQ in parts)
changed the interrupt handler to complete transfers without clearing
XRDY (AL case) and ARDY (NACK case) flags. XRDY or ARDY interrupts will be
fired again. As a result, ISR keep processing transfer after it was already
complete (from the driver code point of view).
A didn't see real impacts of the 1d7afc9, but it is really bad idea to
have ISR running on user data after transfer was complete.
It looks, what 1d7afc9 violate TI specs in what how AL and NACK should be
handled (see Note 1, sprugn4r, Figure 17-31 and Figure 17-32).
According to specs (if I understood correctly), in case of NACK and AL driver
must reset NACK, AL, ARDY, RDR, and RRDY (Master Receive Mode), and
NACK, AL, ARDY, and XDR (Master Transmitter Mode).
All that is done down the code under the if condition:
if (stat & (OMAP_I2C_STAT_ARDY | OMAP_I2C_STAT_NACK | OMAP_I2C_STAT_AL)) ...
The patch restore pre 1d7afc9 logic of handling NACK and AL interrupts, so
no interrupts is fired after ISR informs the rest of driver what transfer
complete.
Note: instead of removing break under NACK case, we could just replace 'break'
with 'continue' and allow NACK transfer to finish using ARDY event. I found
that NACK and ARDY bits usually set together. That case confirm TI wiki:
http://processors.wiki.ti.com/index.php/I2C_Tips#Detecting_and_handling_NACK
In order if someone interested in the event traces for NACK and AL cases,
I sent them to mailing list.
Tested on Beagleboard XM C.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Fixes: 1d7afc9 i2c: omap: ack IRQ in parts
Cc: <stable@vger.kernel.org> # v3.7+
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This fixes the following kbuild test robot warning:
>> drivers/i2c/busses/i2c-dln2.c:70:1-4: WARNING: end returns can be simplified if negative or 0 value
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch adds support for the Diolan DLN-2 I2C master module. Due
to hardware limitations it does not support SMBUS quick commands.
Information about the USB protocol interface can be found in the
Programmer's Reference Manual [1], see section 6.2.2 for the I2C
master module commands and responses.
[1] https://www.diolan.com/downloads/dln-api-manual.pdf
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Johan Hovold <johan@kernel.org>
[Lee: Fixed some whitespace issues in Kconfig]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Clients instantiated from OF get an IRQ mapping created at device
registration time. Dispose the mapping when the client is removed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
iowait is for blkio [1]. I2C shouldn't use it.
[1] https://lkml.org/lkml/2014/11/3/317
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@kernel.org
|
|
We have a central copy of the GPL for that. Some addresses were already
outdated.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Pull i2c updates from Wolfram Sang:
"Highlights from the I2C subsystem for 3.18:
- new drivers for Axxia AM55xx, and Hisilicon hix5hd2 SoC.
- designware driver gained AMD support, exynos gained exynos7 support
The rest is usual driver stuff. Hopefully no lowlights this time"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i801: Add Device IDs for Intel Sunrise Point PCH
i2c: hix5hd2: add i2c controller driver
i2c-imx: Disable the clock on probe failure
i2c: designware: Add support for AMD I2C controller
i2c: designware: Rework probe() to get clock a bit later
i2c: designware: Default to fast mode in case of ACPI
i2c: axxia: Add I2C driver for AXM55xx
i2c: exynos: add support for HSI2C module on Exynos7
i2c: mxs: detect No Slave Ack on SELECT in PIO mode
i2c: cros_ec: Remove EC_I2C_FLAG_10BIT
i2c: cros-ec-tunnel: Add of match table
i2c: rcar: remove sign-compare flaw
i2c: ismt: Use minimum descriptor size
i2c: imx: Add arbitration lost check
i2c: rk3x: Remove unlikely() annotations
i2c: rcar: check for no IRQ in rcar_i2c_irq()
i2c: rcar: make rcar_i2c_prepare_msg() *void*
i2c: rcar: simplify check for last message
i2c: designware: add support of platform data to set I2C mode
i2c: designware: add support of I2C standard mode
|
|
This patch adds the I2C/SMBus Device IDs for the Intel Sunrise Point PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
I2C drivers for hix5hd2 soc series, including following chipset
Hi3716CV200, Hi3719CV100, Hi3718CV100, Hi3719MV100, Hi3718MV100.
Signed-off-by: Wei Yan <sledge.yanwei@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
[wsa: folded dt docs into this patch]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Pull MFD updates from Lee Jones:
"Changes to existing drivers:
- DT clean-ups in da9055-core, max14577, rn5t618, arizona, hi6421, stmpe, twl4030
- Export symbols for use in modules in max14577
- Plenty of static code analysis/Coccinelle fixes throughout the SS
- Regmap clean-ups in arizona, wm5102, wm5110, da9052, tps65217, rk808
- Remove unused/duplicate code in da9052, 88pm860x, ti_ssp, lpc_sch, arizona
- Bug fixes in ti_am335x_tscadc, da9052, ti_am335x_tscadc, rtsx_pcr
- IRQ fixups in arizona, stmpe, max14577
- Regulator related changes in axp20x
- Pass DMA coherency information from parent => child in MFD core
- Rename DT document files for consistency
- Add ACPI support to the MFD core
- Add Andreas Werner to MAINTAINERS for MEN F21BMC
New drivers/supported devices:
- New driver for MEN 14F021P00 Board Management Controller
- New driver for Ricoh RN5T618 PMIC
- New driver for Rockchip RK808
- New driver for HiSilicon Hi6421 PMIC
- New driver for Qualcomm SPMI PMICs
- Add support for Intel Braswell in lpc_ich
- Add support for Intel 9 Series PCH in lpc_ich
- Add support for Intel Quark ILB in lpc_sch"
[ Delayed to after the poweer/reset pull due to Kconfig problems with
recursive Kconfig select/depends-on chains. - Linus ]
* tag 'mfd-for-linus-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (79 commits)
mfd: cros_ec: wait for completion of commands that return IN_PROGRESS
i2c: i2c-cros-ec-tunnel: Set retries to 3
mfd: cros_ec: move locking into cros_ec_cmd_xfer
mfd: cros_ec: stop calling ->cmd_xfer() directly
mfd: cros_ec: Delay for 50ms when we see EC_CMD_REBOOT_EC
MAINTAINERS: Adds Andreas Werner to maintainers list for MEN F21BMC
mfd: arizona: Correct mask to allow setting micbias external cap
mfd: Add ACPI support
Revert "mfd: wm5102: Manually apply register patch"
mfd: ti_am335x_tscadc: Update logic in CTRL register for 5-wire TS
mfd: dt-bindings: atmel-gpbr: Rename doc file to conform to naming convention
mfd: dt-bindings: qcom-pm8xxx: Rename doc file to conform to naming convention
mfd: Inherit coherent_dma_mask from parent device
mfd: Document DT bindings for Qualcomm SPMI PMICs
mfd: Add support for Qualcomm SPMI PMICs
mfd: dt-bindings: pm8xxx: Add new compatible string
mfd: axp209x: Drop the parent supplies field
mfd: twl4030-power: Use 'ti,system-power-controller' as alternative way to support system power off
mfd: dt-bindings: twl4030-power: Use the standard property to mark power control
mfd: syscon: Add Atmel GPBR DT bindings documention
...
|
|
Pull ACPI and power management updates from Rafael Wysocki:
"Features-wise, to me the most important this time is a rework of
wakeup interrupts handling in the core that makes them work
consistently across all of the available sleep states, including
suspend-to-idle. Many thanks to Thomas Gleixner for his help with
this work.
Second is an update of the generic PM domains code that has been in
need of some care for quite a while. Unused code is being removed, DT
support is being added and domains are now going to be attached to
devices in bus type code in analogy with the ACPI PM domain. The
majority of work here was done by Ulf Hansson who also has been the
most active developer this time.
Apart from this we have a traditional ACPICA update, this time to
upstream version 20140828 and a few ACPI wakeup interrupts handling
patches on top of the general rework mentioned above. There also are
several cpufreq commits including renaming the cpufreq-cpu0 driver to
cpufreq-dt, as this is what implements generic DT-based cpufreq
support, and a new DT-based idle states infrastructure for cpuidle.
In addition to that, the ACPI LPSS driver is updated, ACPI support for
Apple machines is improved, a few bugs are fixed and a few cleanups
are made all over.
Finally, the Adaptive Voltage Scaling (AVS) subsystem now has a tree
maintained by Kevin Hilman that will be merged through the PM tree.
Numbers-wise, the generic PM domains update takes the lead this time
with 32 non-merge commits, second is cpufreq (15 commits) and the 3rd
place goes to the wakeup interrupts handling rework (13 commits).
Specifics:
- Rework the handling of wakeup IRQs by the IRQ core such that all of
them will be switched over to "wakeup" mode in suspend_device_irqs()
and in that mode the first interrupt will abort system suspend in
progress or wake up the system if already in suspend-to-idle (or
equivalent) without executing any interrupt handlers. Among other
things that eliminates the wakeup-related motivation to use the
IRQF_NO_SUSPEND interrupt flag with interrupts which don't really
need it and should not use it (Thomas Gleixner and Rafael Wysocki)
- Switch over ACPI to handling wakeup interrupts with the help of the
new mechanism introduced by the above IRQ core rework (Rafael Wysocki)
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during enumeration
(Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in the
METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot (or
after resume from system suspend) and rework the ACPI Smart Battery
Subsystem (SBS) driver to work correctly with Apple platforms
(Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the code,
adding support for 133MHz I2C source clock on Intel Baytrail to it
and making it avoid using UART RTS override with Auto Flow Control
(Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak)
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin)
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui)
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes)
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name change
among other things), ppc-corenet, powernv (Viresh Kumar, Preeti U
Murthy, Shilpasri G Bhat, Lucas Stach)
- cpuidle support for DT-based idle states infrastructure, new ARM64
cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi, Rasmus
Villemoes)
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman)
- Rework of the test_suspend kernel command line argument and a new
trace event for console resume (Srinivas Pandruvada, Todd E Brandt)
- Second attempt to optimize swsusp_free() (hibernation core) to make
it avoid going through all PFNs which may be way too slow on some
systems (Joerg Roedel)
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS entry
update in MAINTAINERS (Heiko Stübner, Kevin Hilman)
- PM core fix related to clock management (Geert Uytterhoeven)
- PM core's sysfs code cleanup (Johannes Berg)"
* tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (105 commits)
ACPI / fan: printk replacement
PM / clk: Fix crash in clocks management code if !CONFIG_PM_RUNTIME
PM / Domains: Rename cpu_data to cpuidle_data
cpufreq: cpufreq-dt: fix potential double put of cpu OF node
cpufreq: cpu0: rename driver and internals to 'cpufreq_dt'
PM / hibernate: Iterate over set bits instead of PFNs in swsusp_free()
cpufreq: ppc-corenet: remove duplicate update of cpu_data
ACPI / sleep: Rework the handling of ACPI GPE wakeup from suspend-to-idle
PM / sleep: Rename platform suspend/resume functions in suspend.c
PM / sleep: Export dpm_suspend_late/noirq() and dpm_resume_early/noirq()
ACPICA: Introduce acpi_enable_all_wakeup_gpes()
ACPICA: Clear all non-wakeup GPEs in acpi_hw_enable_wakeup_gpe_block()
ACPI / video: check _DOD list when creating backlight devices
PM / Domains: Move dev_pm_domain_attach|detach() to pm_domain.h
cpufreq: Replace strnicmp with strncasecmp
cpufreq: powernv: Set the cpus to nominal frequency during reboot/kexec
cpufreq: powernv: Set the pstate of the last hotplugged out cpu in policy->cpus to minimum
cpufreq: Allow stop CPU callback to be used by all cpufreq drivers
PM / devfreq: exynos: Enable building exynos PPMU as module
PM / devfreq: Export helper functions for drivers
...
|
|
Pull "trivial tree" updates from Jiri Kosina:
"Usual pile from trivial tree everyone is so eagerly waiting for"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
Remove MN10300_PROC_MN2WS0038
mei: fix comments
treewide: Fix typos in Kconfig
kprobes: update jprobe_example.c for do_fork() change
Documentation: change "&" to "and" in Documentation/applying-patches.txt
Documentation: remove obsolete pcmcia-cs from Changes
Documentation: update links in Changes
Documentation: Docbook: Fix generated DocBook/kernel-api.xml
score: Remove GENERIC_HAS_IOMAP
gpio: fix 'CONFIG_GPIO_IRQCHIP' comments
tty: doc: Fix grammar in serial/tty
dma-debug: modify check_for_stack output
treewide: fix errors in printk
genirq: fix reference in devm_request_threaded_irq comment
treewide: fix synchronize_rcu() in comments
checkstack.pl: port to AArch64
doc: queue-sysfs: minor fixes
init/do_mounts: better syntax description
MIPS: fix comment spelling
powerpc/simpleboot: fix comment
...
|
|
* pm-domains: (32 commits)
PM / Domains: Rename cpu_data to cpuidle_data
PM / Domains: Move dev_pm_domain_attach|detach() to pm_domain.h
PM / Domains: Remove legacy API for adding devices through DT
PM / Domains: Add genpd attach/detach callbacks
PM / Domains: add debugfs listing of struct generic_pm_domain-s
ACPI / PM: Convert acpi_dev_pm_detach() into a static function
ARM: exynos: Move to generic PM domain DT bindings
amba: Add support for attach/detach of PM domains
spi: core: Convert to dev_pm_domain_attach|detach()
mmc: sdio: Convert to dev_pm_domain_attach|detach()
i2c: core: Convert to dev_pm_domain_attach|detach()
drivercore / platform: Convert to dev_pm_domain_attach|detach()
PM / Domains: Add APIs to attach/detach a PM domain for a device
PM / Domains: Add generic OF-based PM domain look-up
ACPI / PM: Assign the ->detach() callback when attaching the PM domain
PM / Domains: Add a detach callback to the struct dev_pm_domain
PM / domains: Spelling s/domian/domain/
PM / domains: Keep declaration of dev_power_governors together
PM / domains: Remove default_stop_ok() API
drivers: sh: Leave disabling of unused PM domains to genpd
...
|
|
Since the i2c bus can get wedged on the EC sometimes, set the number of retries
to 3. Since we un-wedge the bus immediately after the wedge happens, this is the
correct fix since only one transfer will fail.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Instead of having users of the ChromeOS EC call the interface-specific
cmd_xfer() callback directly, introduce a central cros_ec_cmd_xfer()
to use instead. This will allow us to put all the locking and retry
logic in one place instead of duplicating it across the different
drivers.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
In the case of errors during probe, we should disable i2c_imx->clk.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add support for AMD version of the DW I2C host controller. The device is
enumerated from ACPI namespace with ACPI ID AMD0010. Because the core
driver needs an input source clock, and this is not an Intel LPSS device
where clocks are provided through drivers/acpi/acpi_lpss.c, we register the
clock ourselves if the clock rate is given in ->driver_data
Signed-off-by: Carl Peng <carlpeng008@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
In order to be able to create missing clock for AMD (and in future possibly
others) we move getting clock for the device a bit later. Also make ACPI/DT
configuration in the same place depending on from where the device was
enumerated from.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
There is no way in ACPI to tell in which speed the host controller is
supposed to run, so we default to fast mode (400KHz). Since this has been
the default all the time there should be no functional changes with this
change.
This is the first step required to refactor the driver probe so that we can
supply source clock from ACPI part of the driver to the core.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add I2C bus driver for the controller found in the LSI Axxia family SoCs. The
driver implements 10-bit addressing and SMBus transfer modes via emulation
(including SMBus block data read).
Signed-off-by: Anders Berg <anders.berg@avagotech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The HSI2C module on Exynos7 differs in the transfer status
bits. Transfer status bits were moved to INT_ENABLE and
INT_STATUS registers
This patch adds support for the HSI2C module on Exynos7.
1. Implementes a "hw" field in the variant struct to distinguish
the hardware.
2. Updates the dt-new compatible in dt-binding documenation
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
i2cdetect scanned i2c bus slow because the i2c-mxs driver ignored the
NO_SLAVE_ACK bit during busy-waiting loop. Thanks to the patch, the
speedup happens.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The runtime pm calls need to be done before populating the children via the
i2c_add_adapter call. If this is not done, a child can run into issues trying
to do i2c read/writes due to the pm_runtime_sync failing.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
i2cdetect -q was broken (everything was a false positive, and no transfers were
actually being sent over i2c). The way it works is by sending a 0 length write
request and checking for NACK. This patch fixes the 0 length writes and actually
sends them.
Reported-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Tested-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
In <https://lkml.org/lkml/2014/6/10/265> pointed out that the 10-bit
flag in the cros_ec_tunnel was useless. It went into a 16-bit flags
field but was defined at (1 << 16).
Since we have no 10-bit i2c devices on the other side of the tunnel on
any known devices this was never a problem. Until we do it makes
sense to remove this code. On the EC side the code to handle this
flag was removed in <https://chromium-review.googlesource.com/204162>.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The commit 46420dd73b80 (PM / Domains: Add APIs to attach/detach a PM
domain for a device) started using errno values in pm.h header file.
It also failed to include the header for these, thus it caused
compiler errors.
Instead of including the errno header to pm.h, let's move the functions
to pm_domain.h, since it's a better match.
Fixes: 46420dd73b80 (PM / Domains: Add APIs to attach/detach a PM domain for a device)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
To enable the cros-ec-tunnel driver to be auto-loaded when build as a
module add an of match table (and export it) to match the modalias
information passed on to userspace as the Cros EC MFD driver registers
the MFD subdevices with an of_compatibility string.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
gcc rightfully says:
drivers/i2c/busses/i2c-rcar.c:198:10: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Software is allowed to allocate number of descriptor size from 2 to 256,
this i2c controller could process more descriptor, but for i2c core soft
ware layer, only one i2c transaction is allowed each time.
So here switch to minimum 2 descriptor when initialization.
Signed-off-by: Fan Du <fan.du@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
According to the i.mx spec, for multimaster mode, if I2C is
enabled when the bus is busy and asserts start, hardware inhibits
the transmission, clears MSTA without signaling a stop, generate
an interrupt, and set I2C_I2SR[IAL] to indicate a failed attempt
to engage the bus, which means arbitration lost. In this case,
we should first test I2C_I2SR[IAL], and clear this bit if it is
set, and then I2C controller default to slave receive mode.
This patch check the IAL bit every time before an I2c transmission.
if IAL is set, clear it and make I2C controller to default mode.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Having a transfer more than 32 bits is not all that unlikely. Remove
the annotation.
The unlikely in the IRQ handler can't gain us much. It's not in a
loop, so at most it would save 1 instruction per IRQ, which isn't
much. In fact on the compiler I tested it produced the exact same
code. Remove it too.
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Check if the ICMSR register (masked with the ICMIER register) evaluates to 0 in
the driver's interrupt handler and return IRQ_NONE in that case, like many other
drivers do.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
rcar_i2c_prepare_msg() always returns 0, so we can make this function return
*void* and thus remove the result check in rcar_i2c_master_xfer().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
rcar_i2c_master_xfer() needlessly compares the message pointers (using indirect
addressing) in order to detect the last I2C message, while it's enough to only
compare the message indexes.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Use the platform data to set the clk_freq when there is no DT configuration
available. The clk_freq in turn will determine the I2C speed mode.
In Quark, there is currently no other configuration mechanism other than
board files.
Signed-off-by: Raymond Tan <raymond.tan@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hock Leong Kweh <hock.leong.kweh@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Some legacy devices support ony I2C standard mode at 100kHz.
This patch allows to select the standard mode through the DTS
with the use of the existing clock-frequency parameter.
When clock-frequency parameter is not set, the fast mode is selected.
Only when the parameter is set at 100000, the standard mode is selected.
Signed-off-by: Romain Baeriswyl <romainba@abilis.com>
Reviewed-by: Christian Ruppert <christian.ruppert@abilis.com>
Acked-by: Alan Tull <atull@opensource.altera.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This patch fix spelling typos found in Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
If adapter->dev.parent == NULL there is a NULL pointer dereference in
acpi_i2c_install_space_handler and acpi_i2c_remove_space_handler.
This is present since introduction of this code:
366047515c6e "i2c: rework kernel config I2C_ACPI" or even
da3c6647ee08 "I2C/ACPI: Clean up I2C ACPI code and Add CONFIG_I2C_ACPI"
The adapter->dev.parent == NULL case is valid for the i2c_stub,
so loading i2c_stub with ACPI_I2C_OPREGION enabled results in an oops.
This is also valid at least for i2c_tiny_usb and i2c_robotfuzz_osif.
Fix by checking whether it is null before calling ACPI_HANDLE.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Commit 5d98e61d337c ("I2C/ACPI: Add i2c ACPI operation region support")
renamed the i2c-core module. This may cause regressions for
distributions, so put the ACPI code back into the core.
Reported-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Lan Tianyu <tianyu.lan@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
Linus Torvalds
Rafael J. Wysocki
Vishnu Motghare
Grygorii Strashko
Lan Tianyu
Alexander Kochetkov
Andrew Jackson
Octavian Purdila
Laurentiu Palcu
Laurent Pinchart
Wolfram Sang
Wolfram Sang
james.d.ralston@intel.com
Wei Yan
Derek Basehore
Andrew Bresticker
Fabio Estevam
Carl Peng
Mika Westerberg
Anders Berg
Naveen Krishna Ch
Janusz Użycki
Andy Gross
Alexandru M Stan
Doug Anderson
Ulf Hansson
Sjoerd Simons
Fan Du
Haibo Chen
Sergei Shtylyov
Tan, Raymond
Romain Baeriswyl
Masanari Iida
Peter Hüwe