| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Sometimes we would get the following flow when doing an i2cset:
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
I2C_SLAVE_WRITE_RECEIVED
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x714 : INTR_STAT=0x204
I2C_SLAVE_WRITE_REQUESTED
I2C_SLAVE_WRITE_RECEIVED
Documentation/i2c/slave-interface.rst says that I2C_SLAVE_WRITE_REQUESTED,
which is mandatory, should be sent while the data did not arrive yet. It
means in a write-request I2C_SLAVE_WRITE_REQUESTED should be reported
before any I2C_SLAVE_WRITE_RECEIVED.
By the way, I2C_SLAVE_STOP didn't be reported in the above case because
DW_IC_INTR_STAT was not 0x200.
dev->status can be used to record the current state, especially Designware
I2C controller has no interrupts to identify a write-request. This patch
makes not only I2C_SLAVE_WRITE_REQUESTED been reported first when
IC_INTR_RX_FULL is rising and dev->status isn't STATUS_WRITE_IN_PROGRESS
but also I2C_SLAVE_STOP been reported when a STOP condition is received.
Signed-off-by: Michael Wu <michael.wu@vatics.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
If some bits were cleared by i2c_dw_read_clear_intrbits_slave() in
i2c_dw_isr_slave() and not handled immediately, those cleared bits would
not be shown again by later i2c_dw_read_clear_intrbits_slave(). They
therefore were forgotten to be handled.
i2c_dw_read_clear_intrbits_slave() should be called once in an ISR and take
its returned state for all later handlings.
Signed-off-by: Michael Wu <michael.wu@vatics.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The Mellanox BlueField I2C controller is only present on Mellanox
BlueField SoCs. Hence add a dependency on MELLANOX_PLATFORM, to prevent
asking the user about this driver when configuring a kernel without
Mellanox platform support.
Fixes: b5b5b32081cd206b ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Correct the email addresses of the author and the maintainer
of the Mellanox BlueField I2C driver.
Fixes: b5b5b32081cd206b ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The reference clock frequency remains the same across Bluefield
products. Thus, update the frequency and rename the macro.
Fixes: b5b5b32081cd206b ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Few wrapper functions are useless and can be inlined. So
delete mlxbf_i2c_read() and mlxbf_i2c_write() and replace
them with readl() and writel(), respectively. Also delete
mlxbf_i2c_read_data() and mlxbf_i2c_write() and replace
them with ioread32be() and iowrite32be(), respectively.
Fixes: b5b5b32081cd206b ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Address warnings "warning: cast to restricted __be32" reported
by sparse.
Fixes: b5b5b32081cd206b ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The build fails with "implicit declaration of function
'acpi_device_uid'" error. Thus, protect ACPI function calls
from being called when CONFIG_ACPI is disabled.
Fixes: b5b5b32081cd206b ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Implements atomic transfers to fix reboot/shutdown on r8a7790 Lager and
similar boards.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
[wsa: some whitespace fixing]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The i2c driver default do dma reset after i2c reset, but sometimes
i2c reset will trigger dma tx2rx, then apdma write data to dram
which has been i2c_put_dma_safe_msg_buf(kfree). Move dma reset
before i2c reset in mtk_i2c_init_hw to fix it.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Commit 21653a4181ff ("i2c: core: Call i2c_acpi_install_space_handler()
before i2c_acpi_register_devices()")'s intention was to only move the
acpi_install_address_space_handler() call to the point before where
the ACPI declared i2c-children of the adapter where instantiated by
i2c_acpi_register_devices().
But i2c_acpi_install_space_handler() had a call to
acpi_walk_dep_device_list() hidden (that is I missed it) at the end
of it, so as an unwanted side-effect now acpi_walk_dep_device_list()
was also being called before i2c_acpi_register_devices().
Move the acpi_walk_dep_device_list() call to the end of
i2c_acpi_register_devices(), so that it is once again called *after*
the i2c_client-s hanging of the adapter have been created.
This fixes the Microsoft Surface Go 2 hanging at boot.
Fixes: 21653a4181ff ("i2c: core: Call i2c_acpi_install_space_handler() before i2c_acpi_register_devices()")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209627
Reported-by: Rainer Finke <rainer@finke.cc>
Reported-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Suggested-by: Maximilian Luz <luzmaximilian@gmail.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Pull i2c updates from Wolfram Sang:
- if a host can be a client, too, the I2C core can now use it to
emulate SMBus HostNotify support (STM32 and R-Car added this so far)
- also for client mode, a testunit has been added. It can create rare
situations on the bus, so host controllers can be tested
- a binding has been added to mark the bus as "single-master". This
allows for better timeout detections
- new driver for Mellanox Bluefield
- massive refactoring of the Tegra driver
- EEPROMs recognized by the at24 driver can now have custom names
- rest is driver updates
* 'i2c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (80 commits)
Documentation: i2c: add testunit docs to index
i2c: tegra: Improve driver module description
i2c: tegra: Clean up whitespaces, newlines and indentation
i2c: tegra: Clean up and improve comments
i2c: tegra: Clean up printk messages
i2c: tegra: Clean up variable names
i2c: tegra: Improve formatting of variables
i2c: tegra: Check errors for both positive and negative values
i2c: tegra: Factor out hardware initialization into separate function
i2c: tegra: Factor out register polling into separate function
i2c: tegra: Factor out packet header setup from tegra_i2c_xfer_msg()
i2c: tegra: Factor out error recovery from tegra_i2c_xfer_msg()
i2c: tegra: Rename wait/poll functions
i2c: tegra: Remove "dma" variable from tegra_i2c_xfer_msg()
i2c: tegra: Remove redundant check in tegra_i2c_issue_bus_clear()
i2c: tegra: Remove likely/unlikely from the code
i2c: tegra: Remove outdated barrier()
i2c: tegra: Clean up variable types
i2c: tegra: Reorder location of functions in the code
i2c: tegra: Clean up probe function
...
|
|
When the NACK and BUS error bits are set by the hardware, the driver is
responsible for clearing them by writing "1" into the corresponding
status registers.
Hence perform the necessary operations in owl_i2c_interrupt().
Fixes: d211e62af466 ("i2c: Add Actions Semiconductor Owl family S900 I2C driver")
Reported-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
This reverts commit fa4d30556883f2eaab425b88ba9904865a4d00f3. An updated
version was sent. So, revert this version and give the new version more
time for testing.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Apparently, 15 cycles of the peripheral clock are used by the controller
for sampling and filtering. Because this was not known before, the rate
calculation is slightly off.
Clean up and fix the calculation taking this filtering delay into account.
Fixes: 30021e3707a7 ("i2c: add support for Amlogic Meson I2C controller")
Signed-off-by: Nicolas Belin <nbelin@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
SCL rate appears to be different than what is expected. For example,
We get 164kHz on i2c3 of the vim3 when 400kHz is expected. This is
partially due to the peripheral clock being disabled when the clock is
set.
Let's keep the peripheral clock on after probe to fix the problem. This
does not affect the SCL output which is still gated when i2c is idle.
Fixes: 09af1c2fa490 ("i2c: meson: set clock divider in probe instead of setting it for each transfer")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
When the slave address is written in do_start(), SLAVE_ADDR is written
completely. This may overwrite some setting related to the clock rate
or signal filtering.
Fix this by writing only the bits related to slave address. To avoid
causing unexpected changed, explicitly disable filtering or high/low
clock mode which may have been left over by the bootloader.
Fixes: 30021e3707a7 ("i2c: add support for Amlogic Meson I2C controller")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
According to the "VFxxx Controller Reference Manual" (and the comment
block starting at line 97), Vybrid requires writing a one for clearing
an interrupt flag. Syncing the method for clearing I2SR_IIF in
i2c_imx_isr().
Signed-off-by: Christian Eggers <ceggers@arri.de>
Fixes: 4b775022f6fd ("i2c: imx: add struct to hold more configurable quirks")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Use proper spelling of "NVIDIA" and don't designate driver as Tegra2-only
since newer SoC generations are supported as well.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Some places in the code are missing newlines or have unnecessary
whitespaces and newlines. This creates inconsistency of the code and
hurts readability. This patch removes the unnecessary and adds necessary
whitespaces / newlines, clears indentation of the code.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Make all comments to be consistent in regards to capitalization and
punctuation, correct spelling and grammar errors, improve wording.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
This patch unifies style of all messages in the driver by starting them
with a lowercase letter and using consistent capitalization and wording
for all messages.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Rename "ret" variables to "err" in order to make code a bit more
expressive, emphasizing that the returned value is an error code.
Same vice versa, where appropriate.
Rename variable "reg" to "val" in order to better reflect the actual
usage of the variable in the code and to make naming consistent with
the rest of the code.
Use briefer names for a few members of the tegra_i2c_dev structure in
order to improve readability of the code.
All dev/&pdev->dev are replaced with i2c_dev->dev in order to have uniform
code style across the driver.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Reorder definition of variables in the code to have them sorted by length
and grouped logically, also replace "unsigned long" with "u32". Do this in
order to make code easier to read.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The driver's code is inconsistent in regards to the error values checking.
The correct way should be to check both positive and negative values.
This patch cleans up the error-checks in the code. Note that the
pm_runtime_get_sync() could return positive value on success, hence only
relevant parts of the code are changed by this patch.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Factor out hardware initialization into a separate function from the probe
function. The only place where runtime PM needs to be resumed during probe
is the place of hardware initialization, hence it makes sense to factor
out it in order to have a bit cleaner error handling in tegra_i2c_probe().
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Factor out register polling into a separate function in order to remove
boilerplate code and make code cleaner.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The code related to packet header setting up is a bit messy and makes
tegra_i2c_xfer_msg() more difficult to read than it could be. Let's
factor the packet header setup from tegra_i2c_xfer_msg() into separate
function in order to make code easier to read and follow.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Factor out error recovery code from tegra_i2c_xfer_msg() in order to
make this function easier to read and follow.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Drop '_timeout' postfix from the wait/poll completion function names in
order to make the names shorter, making code cleaner a tad.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The "dma" variable of tegra_i2c_xfer_msg() function doesn't bring much in
regards to readability and generation of the code.
Besides readability, it's also not very nice that the is_curr_dma_xfer
is initialized in tegra_i2c_xfer_msg() and then could be overridden by
tegra_i2c_config_fifo_trig(). In a result, the "dma" variable creates
slight confusion since it's not instantly obvious why it's set after
tegra_i2c_config_fifo_trig().
Hence should be better to have the variable removed. This makes code
more consistent.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The tegra_i2c_wait_for_config_load() checks for 'has_config_load_reg' by
itself, hence there is no need to duplicate the check.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The likely/unlikely annotations should be used only in a hot paths of
performance-critical code. The I2C driver doesn't have such paths, and
thus, there is no justification for usage of likely/unlikely annotations
in the code. Hence remove them.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The barrier() was intended to reduce possibility of racing with the
interrupt handler, but driver's code evolved significantly and today's
driver enables interrupt only when it waits for completion notification.
Hence barrier() has no good use anymore, let's remove it.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Don't use signed types for unsigned values and use consistent types
for sibling variables.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Reorder location of functions in the code in order to have definition
of functions closer to the place of the invocation. This change makes
easier to navigate around the code and removes the need to have a
prototype for tegra_i2c_init().
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The driver's probe function code is a bit difficult to read. This patch
reorders code of the probe function, forming groups of code that are easy
to work with. The probe tear-down order now matches the driver-removal
order.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Move out code related to device-tree parsing from the probe function into
tegra_i2c_parse_dt() in order to make code more consistent.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Use clk-bulk helpers and factor out clocks initialization into separate
function in order to make code cleaner.
The clocks initialization now performed after reset-control initialization
in order to avoid a noisy -PROBE_DEFER errors on T186+ from the clk-bulk
helper which doesn't silence this error code. Hence reset_control_get()
now may return -EPROBE_DEFER on newer Tegra SoCs because they use BPMP
driver that provides reset controls and BPMP doesn't come up early during
boot. Previously rst was protected by the clocks retrieval and now this
patch makes dev_err_probe() to be used for the rst error handling.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Use common helper for retrieval of the interrupt number in order to make
code cleaner. Note that platform_get_irq() prints error message by itself.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Driver now uses devm_platform_get_and_ioremap_resource() which replaces
the typical boilerplate code and makes code cleaner.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Use a single reset_control_reset() instead of assert/deasset couple in
order to make code cleaner a tad. Note that the reset_control_reset()
uses 1 microsecond delay instead of 2 that was used previously, but this
shouldn't matter because one microsecond is a default reset time for most
of Tegra peripherals and TRM doesn't mention anything special in regards
to I2C controller's reset propagation time.
In addition don't ignore potential error of the reset control by emitting
a noisy warning if it fails, which will indicate an existence of a severe
problem, while still allow machine to boot up.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The error message prints number of vIRQ, which isn't a useful information.
In practice devm_request_irq() never fails, hence let's remove the bogus
message in order to make code cleaner.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The runtime PM is guaranteed to be always available on Tegra after commit
40b2bb1b132a ("ARM: tegra: enforce PM requirement"). Hence let's remove
all the RPM-availability checking and handling from the code.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The "non_hs_mode" divisor value is fixed, thus there is no need to have
the variable i2c_dev.clk_divisor_non_hs_mode struct member. Let's remove
it and move the mode selection into tegra_i2c_init() where it can be
united with the timing selection.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
It doesn't make sense to conditionalize the div-clk rate changes because
rate is fixed and it won't ever change once it's set at the driver's probe
time. All further changes are NO-OPs because CCF caches rate and skips
rate-change if rate is unchanged.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The tegra_i2c_issue_bus_clear() may fail and in this case BUS_CLR_DONE
stays unmasked. Hence let's mask it for consistency. This patch doesn't
fix any known problems.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Technically the tegra_i2c_flush_fifos() may fail and transfer should be
aborted in this case, but this shouldn't ever happen in practice unless
there is a bug somewhere in the driver. Let's add the error check just
for completeness.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The pm_runtime_get_sync() always bumps refcount regardless of whether it
succeeds or fails. Hence driver is responsible for restoring of the RPM
refcounting. This patch adds missing RPM puts which restore refcounting
in a case of pm_runtime_get_sync() error.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The tegra_i2c_flush_fifos() shouldn't sleep in atomic transfer and jiffies
are not updating if interrupts are disabled. Let's switch to use iopoll
API helpers for register-polling. The iopoll API provides helpers for both
atomic and non-atomic cases.
Note that this patch doesn't fix any known problem because normally FIFO
is flushed at the time of starting a new transfer.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
Michael Wu
Geert Uytterhoeven
Khalil Blaiech
Ulrich Hecht
Qii Wang
Hans de Goede
Linus Torvalds
Cristian Ciocaltea
Wolfram Sang
Nicolas Belin
Jerome Brunet
Christian Eggers
Dmitry Osipenko