aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/i2c (follow)
AgeCommit message (Collapse)AuthorFilesLines
2017-05-10Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fsLinus Torvalds8-12/+12
Pull hw lockdown support from David Howells: "Annotation of module parameters that configure hardware resources including ioports, iomem addresses, irq lines and dma channels. This allows a future patch to prohibit the use of such module parameters to prevent that hardware from being abused to gain access to the running kernel image as part of locking the kernel down under UEFI secure boot conditions. Annotations are made by changing: module_param(n, t, p) module_param_named(n, v, t, p) module_param_array(n, t, m, p) to: module_param_hw(n, t, hwtype, p) module_param_hw_named(n, v, t, hwtype, p) module_param_hw_array(n, t, hwtype, m, p) where the module parameter refers to a hardware setting hwtype specifies the type of the resource being configured. This can be one of: ioport Module parameter configures an I/O port iomem Module parameter configures an I/O mem address ioport_or_iomem Module parameter could be either (runtime set) irq Module parameter configures an I/O port dma Module parameter configures a DMA channel dma_addr Module parameter configures a DMA buffer address other Module parameter configures some other value Note that the hwtype is compile checked, but not currently stored (the lockdown code probably won't require it). It is, however, there for future use. A bonus is that the hwtype can also be used for grepping. The intention is for the kernel to ignore or reject attempts to set annotated module parameters if lockdown is enabled. This applies to options passed on the boot command line, passed to insmod/modprobe or direct twiddling in /sys/module/ parameter files. The module initialisation then needs to handle the parameter not being set, by (1) giving an error, (2) probing for a value or (3) using a reasonable default. What I can't do is just reject a module out of hand because it may take a hardware setting in the module parameters. Some important modules, some ipmi stuff for instance, both probe for hardware and allow hardware to be manually specified; if the driver is aborts with any error, you don't get any ipmi hardware. Further, trying to do this entirely in the module initialisation code doesn't protect against sysfs twiddling. [!] Note that in and of itself, this series of patches should have no effect on the the size of the kernel or code execution - that is left to a patch in the next series to effect. It does mark annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in an already existing field" * tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits) Annotate hardware config module parameters in sound/pci/ Annotate hardware config module parameters in sound/oss/ Annotate hardware config module parameters in sound/isa/ Annotate hardware config module parameters in sound/drivers/ Annotate hardware config module parameters in fs/pstore/ Annotate hardware config module parameters in drivers/watchdog/ Annotate hardware config module parameters in drivers/video/ Annotate hardware config module parameters in drivers/tty/ Annotate hardware config module parameters in drivers/staging/vme/ Annotate hardware config module parameters in drivers/staging/speakup/ Annotate hardware config module parameters in drivers/staging/media/ Annotate hardware config module parameters in drivers/scsi/ Annotate hardware config module parameters in drivers/pcmcia/ Annotate hardware config module parameters in drivers/pci/hotplug/ Annotate hardware config module parameters in drivers/parport/ Annotate hardware config module parameters in drivers/net/wireless/ Annotate hardware config module parameters in drivers/net/wan/ Annotate hardware config module parameters in drivers/net/irda/ Annotate hardware config module parameters in drivers/net/hamradio/ Annotate hardware config module parameters in drivers/net/ethernet/ ...
2017-05-10Merge tag 'acpi-extra-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pmLinus Torvalds1-0/+2
Pull more ACPI updates from Rafael Wysocki: "These update the ACPICA code in the kernel to upstream revision 20170303 which adds a few minor fixes and improvements, update ACPI SoC drivers with new device IDs, platform-related information and similar, fix the register information in the xpower PMIC driver, introduce a concept of "always present" devices to the ACPI device enumeration code and use it to fix a problem with one platform, and fix a system resume issue related to power resources. Specifics: - Update the ACPICA code in the kernel to upstream revision 20170303 which includes: * Minor fixes and improvements in the core code (Bob Moore, Seunghun Han). * Debugger fixes (Colin Ian King, Lv Zheng). * Compiler/disassembler improvements (Bob Moore, David Box, Lv Zheng). * Build-related update (Lv Zheng). - Add new device IDs and platform-related information to the ACPI drivers for Intel (LPSS) and AMD (APD) SoCs (Hanjun Guo, Hans de Goede). - Make it possible to quirk ACPI-enumerated devices as "always present" on platforms where they are incorrectly reported as not present by the AML and add the INT0002 device ID to the list of "always present" devices (Hans de Goede). - Fix the register information in the xpower PMIC driver and add comments to map the registers to symbols used by AML to it (Hans de Goede). - Move the code turning off unused ACPI power resources during system resume to a point after all devices have been resumed to avoid issues with power resources that do not behave as expected (Hans de Goede)" * tag 'acpi-extra-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (22 commits) ACPI / power: Delay turning off unused power resources after suspend ACPI / PMIC: xpower: Fix power_table addresses ACPI / LPSS: Call pwm_add_table() for Bay Trail PWM device ACPICA: Update version to 20170303 ACPICA: iasl: add ASL conversion tool ACPICA: Local cache support: Allow small cache objects ACPICA: Disassembler: Do not unconditionally remove temporary names ACPICA: iasl: Fix IORT SMMU GSI disassembling ACPICA: Cleanup AML opcode definitions, no functional change ACPICA: Debugger: Add interpreter blocking mark for single-step mode ACPICA: debugger: fix memory leak on Pathname ACPICA: Update for automatic repair code for objects returned by evaluate_object ACPICA: Namespace: fix operand cache leak ACPICA: Fix several incorrect invocations of ACPICA return macro ACPICA: Fix a module for excessive debug output ACPICA: Update some function headers, no funtional change ACPICA: Disassembler: Enhance resource descriptor detection i2c: designware: Add ACPI HID for Hisilicon Hip07/08 I2C controller ACPI / APD: Add clock frequency for Hisilicon Hip07/08 I2C controller ACPI / bus: Add INT0002 to list of always-present devices ...
2017-05-03Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/inputLinus Torvalds2-2/+56
Pull input subsystem updates from Dmitry Torokhov: - a big update from Mauro converting input documentation to ReST format - Synaptics PS/2 is now aware of SMBus companion devices, which means that we can now use native RMI4 protocol to handle touchpads, instead of relying on legacy PS/2 mode. - we removed support from BMA180 accelerometer from input devices as it is now handled properly by IIO - update to TSC2007 to corretcly report pressure - other miscellaneous driver fixes. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (152 commits) Input: ar1021_i2c - use BIT to check for a bit Input: twl4030-pwrbutton - use input_set_capability() helper Input: twl4030-pwrbutton - use correct device for irq request Input: ar1021_i2c - enable touch mode during open Input: add uinput documentation dt-bindings: input: add bindings document for ar1021_i2c driver dt-bindings: input: rotary-encoder: fix typo Input: xen-kbdfront - add module parameter for setting resolution ARM: pxa/raumfeld: fix compile error in rotary controller resources Input: xpad - do not suggest writing to Dominic Input: xpad - don't use literal blocks inside footnotes Input: xpad - note that usb/devices is now at /sys/kernel/debug/ Input: docs - freshen up introduction Input: docs - split input docs into kernel- and user-facing Input: docs - note that MT-A protocol is obsolete Input: docs - update joystick documentation a bit Input: docs - remove disclaimer/GPL notice Input: fix "Game console" heading level in joystick documentation Input: rotary-encoder - remove references to platform data from docs Input: move documentation for Amiga CD32 ...
2017-05-03Merge branch 'i2c/for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linuxLinus Torvalds25-248/+588
Pull i2c updates from Wilfram Sang: "I2C has the following updates for you: - an immutable cross-subsystem branch fixing PMIC access on Intel Baytrail - bigger driver updates to the designware, meson, exynos5 drivers - new i2c_acpi_new_device() function to create devices from ACPI - struct i2c_driver has now a flag 'disable_i2c_core_irq_mapping' to allow custom IRQ mapping in case the default does not fit - mux subsystem centralized error messages in its core - new driver for ltc4306 i2c mux - usual set of small updates" * 'i2c/for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (44 commits) i2c: thunderx: Enable HWMON class probing i2c: rcar: clarify PM handling with more comments i2c: rcar: fix resume by always initializing registers before transfer i2c: tegra: fix spelling mistake: "contoller" -> "controller" i2c: exynos5: use core helper to get driver data i2c: exynos5: de-duplicate error logs on clock setup i2c: exynos5: simplify clock frequency handling i2c: exynos5: simplify timings calculation i2c: designware-baytrail: fix potential null pointer dereference on dev i2c: designware: Get selected speed mode sda-hold-time via ACPI [media] cx231xx: stop double error reporting i2c: core: Allow drivers to disable i2c-core irq mapping i2c: core: Add new i2c_acpi_new_device helper function i2c: core: Allow getting ACPI info by index i2c: img-scb: use setup_timer i2c: i2c-scmi: add a MS HID i2c: mux: ltc4306: LTC4306 and LTC4305 I2C multiplexer/switch dt-bindings: i2c: mux: ltc4306: Add dt-bindings for I2C multiplexer/switch i2c: mux: reg: stop double error reporting i2c: mux: pinctrl: stop double error reporting ...
2017-04-27i2c: designware: Add ACPI HID for Hisilicon Hip07/08 I2C controllerHanjun Guo1-0/+2
Add ACPI HID HISI02A1 and HISI02A2 for Hisilicon Hip07/08, which have different clock frequency. Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-04-21i2c: thunderx: Enable HWMON class probingJan Glauber1-0/+1
Set I2C_CLASS_HWMON to enable automatic probing of BMC devices by the ipmi-ssif driver. Signed-off-by: Jan Glauber <jglauber@cavium.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-04-21i2c: rcar: clarify PM handling with more commentsWolfram Sang1-1/+3
PM handling is correct but might be a bit subtle. Add some comments for clarification. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-04-21i2c: rcar: fix resume by always initializing registers before transferWolfram Sang1-2/+2
Resume failed because of uninitialized registers. Instead of adding a resume callback, we simply initialize registers before every transfer. This lightweight change is more robust and will keep us safe if we ever need support for power domains or dynamic frequency changes. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-04-21i2c: tegra: fix spelling mistake: "contoller" -> "controller"Colin Ian King1-1/+1
trivial fix to spelling mistake in MODULE_DESCRIPTION text Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-04-21i2c: exynos5: use core helper to get driver dataAndrzej Hajda1-12/+3
Driver core provides of_device_get_match_data which can be used to get driver data instead of custom helper. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Tested-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-04-21i2c: exynos5: de-duplicate error logs on clock setupAndrzej Hajda1-17/+7
In case of clock setup error it is enough to log it once. Moreover patch simplifies clock setup routines. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Tested-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-04-21i2c: exynos5: simplify clock frequency handlingAndrzej Hajda1-33/+12
There is no need to keep separate settings for high and fast speed clock. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Tested-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-04-21i2c: exynos5: simplify timings calculationAndrzej Hajda1-26/+14
Instead of using cryptic loop direct calculation of timings can be used. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Tested-by: Javier Martinez Canillas <javier@osg.samsung.com> Reviewed-by: Andi Shyti <andi.shyti@samsung.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-04-20Annotate hardware config module parameters in drivers/i2c/David Howells8-12/+12
When the kernel is running in secure boot mode, we lock down the kernel to prevent userspace from modifying the running kernel image. Whilst this includes prohibiting access to things like /dev/mem, it must also prevent access by means of configuring driver modules in such a way as to cause a device to access or modify the kernel image. To this end, annotate module_param* statements that refer to hardware configuration and indicate for future reference what type of parameter they specify. The parameter parser in the core sees this information and can skip such parameters with an error message if the kernel is locked down. The module initialisation then runs as normal, but just sees whatever the default values for those parameters is. Note that we do still need to do the module initialisation because some drivers have viable defaults set in case parameters aren't specified and some drivers support automatic configuration (e.g. PNP or PCI) in addition to manually coded parameters. This patch annotates drivers in drivers/i2c/. Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk> Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Jean Delvare <jdelvare@suse.de> cc: linux-i2c@vger.kernel.org
2017-04-19i2c: designware-baytrail: fix potential null pointer dereference on devColin Ian King1-1/+3
The assignment to addr requires a call to get_sem_addr that dereferences dev, however, this dereference occurs before a null pointer check on dev. Move this assignment after the null check on dev to avoid a potential null pointer dereference. Detected by CoverityScan, CID#1419700 ("Dereference before null check") Fixes: fd476fa22a1f432 ("i2c: designware-baytrail: Add support for cherrytrail") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-04-19i2c: designware: Get selected speed mode sda-hold-time via ACPIchin.yew.tan@intel.com1-9/+22
Sda-hold-time is an important parameter for tuning i2c to meet the electrical specification especially for high speed. I2C with incorrect sda-hold-time may cause lost arbitration error. Instead of loading all speed mode settings, only selected speed mode settings are loaded. Signed-off-by: Tan Chin Yew <chin.yew.tan@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-04-16Merge branch 'i2c/for-INT33FE' into i2c/for-4.12Wolfram Sang1-3/+59
Pull in the immutable branch with I2C ACPI core extensions to support the INT33FE driver.
2017-04-16i2c: core: Allow drivers to disable i2c-core irq mappingHans de Goede1-3/+3
By default the i2c-core will try to get an irq with index 0 on ACPI / of instantiated devices. This is troublesome on some ACPI systems where the irq info at index 0 in the CRS table may contain nonsense and/or point to an irqchip for which there is no Linux driver. If this happens then before this commit the driver's probe method would never get called because i2c_device_probe will try to get an irq by calling acpi_dev_gpio_irq_get which will always return -EPROBE in this case, as it waits for a matching irqchip driver to load. Thus causing the driver to not get a chance to bind. This commit adds a new disable_i2c_core_irq_mapping flag to struct i2c_driver which a driver can set to tell the core to skip irq mapping. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-04-16i2c: core: Add new i2c_acpi_new_device helper functionHans de Goede1-0/+49
By default the i2c subsys creates an i2c-client for the first I2cSerialBus resource of an acpi_device, but some acpi_devices have multiple I2cSerialBus resources and we may want to instantiate i2c-clients for the others. This commit adds a new i2c_acpi_new_device function which can be used to create an i2c-client for any I2cSerialBus resource of an acpi_device. Note that the other resources may even be on a different i2c bus, so just retrieving the client address is not enough. Here is an example DSDT excerpt from such a device: Device (WIDR) { Name (_HID, "INT33FE" /* XPOWER Battery Device */) Name (_CID, "INT33FE" /* XPOWER Battery Device */) Name (_DDN, "WC PMIC Battery Device") <snip> Name (RBUF, ResourceTemplate () { I2cSerialBusV2 (0x005E, ControllerInitiated, 0x000186A0, AddressingMode7Bit, "\\_SB.PCI0.I2C7", 0x00, ResourceConsumer, , Exclusive, ) I2cSerialBusV2 (0x0036, ControllerInitiated, 0x000186A0, AddressingMode7Bit, "\\_SB.PCI0.I2C1", 0x00, ResourceConsumer, , Exclusive, ) I2cSerialBusV2 (0x0022, ControllerInitiated, 0x00061A80, AddressingMode7Bit, "\\_SB.PCI0.I2C1", 0x00, ResourceConsumer, , Exclusive, ) I2cSerialBusV2 (0x0054, ControllerInitiated, 0x00061A80, AddressingMode7Bit, "\\_SB.PCI0.I2C1", 0x00, ResourceConsumer, , Exclusive, ) GpioInt (Level, ActiveLow, Exclusive, PullNone, 0x0000, "\\_SB.PCI0.I2C7.PMI5", 0x00, ResourceConsumer, , ) { // Pin list 0x0012 } GpioInt (Edge, ActiveLow, ExclusiveAndWake, PullNone, 0x0000, "\\_SB.GPO1", 0x00, ResourceConsumer, , ) { // Pin list 0x0005 } GpioInt (Level, ActiveLow, Exclusive, PullNone, 0x0000, "\\_SB.PCI0.I2C7.PMI5", 0x00, ResourceConsumer, , ) { // Pin list 0x0013 } }) Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings { Return (RBUF) /* \_SB_.PCI0.I2C7.WIDR.RBUF */ } <snip> } Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-04-16i2c: core: Allow getting ACPI info by indexHans de Goede1-0/+7
Modify struct i2c_acpi_lookup and i2c_acpi_fill_info() to allow using them to get the info from a certain index in the ACPI-resource list rather then taking the first I2cSerialBus resource. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-04-16i2c: img-scb: use setup_timerGeliang Tang1-3/+2
Use setup_timer() instead of init_timer() to simplify the code. Signed-off-by: Geliang Tang <geliangtang@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-04-16i2c: i2c-scmi: add a MS HIDEdgar Cherkasov1-0/+4
Description of the problem: - i2c-scmi driver contains only two identifiers "SMBUS01" and "SMBUSIBM"; - the fist HID (SMBUS01) is clearly defined in "SMBus Control Method Interface Specification, version 1.0": "Each device must specify 'SMBUS01' as its _HID and use a unique _UID value"; - unfortunately, BIOS vendors (like AMI) seem to ignore this requirement and implement "SMB0001" HID instead of "SMBUS01"; - I speculate that they do this because only "SMB0001" is hard coded in Windows SMBus driver produced by Microsoft. This leads to following situation: - SMBus works out of box in Windows but not in Linux; - board vendors are forced to add correct "SMBUS01" HID to BIOS to make SMBus work in Linux. Moreover the same board vendors complain that tools (3-rd party ASL compiler) do not like the "SMBUS01" identifier and produce errors. So they need to constantly patch the compiler for each new version of BIOS. As it is very unlikely that BIOS vendors implement a correct HID in future, I would propose to consider whether it is possible to work around the problem by adding MS HID to the Linux i2c-scmi driver. v2: move the definition of the new HID to the driver itself. Signed-off-by: Edgar Cherkasov <echerkasov@dev.rtsoft.ru> Signed-off-by: Michael Brunner <Michael.Brunner@kontron.com> Acked-by: Viktor Krasnov <vkrasnov@dev.rtsoft.ru> Reviewed-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-04-16Merge branch 'i2c-mux/for-next' of https://github.com/peda-r/i2c-mux into i2c/for-4.12Wolfram Sang10-30/+352
Pull in changes from the i2c-mux subsubsystem: "Here are a new LTC4306/5 driver, a fix needed by the RT kernel and some error message cleanup."
2017-04-12i2c: mux: ltc4306: LTC4306 and LTC4305 I2C multiplexer/switchMichael Hennerich3-0/+334
This patch adds support for the Analog Devices / Linear Technology LTC4306 and LTC4305 4/2 Channel I2C Bus Multiplexer/Switches. The LTC4306 optionally provides two general purpose input/output pins (GPIOs) that can be configured as logic inputs, opendrain outputs or push-pull outputs via the generic GPIOLIB framework. Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Peter Rosin <peda@axentia.se>
2017-04-11Backmerge tag 'v4.11-rc6' into drm-nextDave Airlie1-28/+6
Linux 4.11-rc6 drm-misc needs 4.11-rc5, may as well fix conflicts with rc6.
2017-04-03Merge branch 'ib/4.11-rc3-i2c-irq-resources' into nextDmitry Torokhov2-2/+56
Bring in changes to i2c to better manage device properties and to allow specifying client interrupt through a resource structure.
2017-04-03i2c: mux: reg: stop double error reportingPeter Rosin1-3/+1
i2c_mux_add_adapter already logs a message on failure. Reviewed-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Peter Rosin <peda@axentia.se>
2017-04-03i2c: mux: pinctrl: stop double error reportingPeter Rosin1-3/+1
i2c_mux_add_adapter already logs a message on failure. Reviewed-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Peter Rosin <peda@axentia.se>
2017-04-03i2c: mux: pca954x: stop double error reportingPeter Rosin1-6/+1
i2c_mux_add_adapter already logs a message on failure. Reviewed-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Peter Rosin <peda@axentia.se>
2017-04-03i2c: mux: pca9541: stop double error reportingPeter Rosin1-3/+1
i2c_mux_add_adapter already logs a message on failure. Reviewed-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Peter Rosin <peda@axentia.se>
2017-04-03i2c: mux: gpio: stop double error reportingPeter Rosin1-3/+1
i2c_mux_add_adapter already logs a message on failure. Reviewed-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Peter Rosin <peda@axentia.se>
2017-04-03i2c: arb: gpio-challenge: stop double error reportingPeter Rosin1-3/+1
i2c_mux_add_adapter already logs a message on failure. Reviewed-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Peter Rosin <peda@axentia.se>
2017-04-03i2c: mux: provide more info on failure in i2c_mux_add_adapterPeter Rosin1-3/+6
No callers then need to report any further info, thus reducing both the amount of code and the log noise. Reviewed-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Peter Rosin <peda@axentia.se>
2017-04-01i2c: allow attaching IRQ resources to i2c_board_infoDmitry Torokhov2-0/+42
Simple integer for interrupt number is not expressive enough, as it does not convey interrupt trigger type that should be used. Let's allow attaching array of resources to the board info and have i2c core parse first IRQ resource and set up interrupt trigger as needed. Reviewed-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2017-04-01i2c: copy device properties when using i2c_register_board_info()Dmitry Torokhov1-0/+12
This will allow marking device property lists as __initdata, the same as board info structures themselves. Reviewed-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2017-04-01i2c: export i2c_client_type structureDmitry Torokhov1-2/+2
i2c bus has 2 different types of device belonging to the same bus and bus notifiers use device type to distinguish between adapters and clients. Previously we only had i2c_adapter_type exported, which made code wanting to work with i2c_client devices test for type not equal to adapter type. This unfortunately is not safe if we ever add another type to the bus, so let's export i2c_client_type as well. Reviewed-by: Jean Delvare <jdelvare@suse.de> Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Reviewed-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2017-03-30i2c: meson: improve and simplify interrupt handlerHeiner Kallweit1-30/+10
The preceding changes in this patch series now allow to simplify the interrupt handler significantly. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-03-30i2c: meson: remove meson_i2c_write_tokensHeiner Kallweit1-10/+4
meson_i2c_write_tokens is always called directly after meson_i2c_prepare_xfer (and only then). So we can simplify the code by removing meson_i2c_write_tokens and moving the two statements of meson_i2c_write_tokens to the end of meson_i2c_prepare_xfer. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-03-30i2c: meson: don't create separate token chain just for the stop commandHeiner Kallweit1-18/+5
We can directly add the stop token to the token chain including the last transfer chunk. This is more efficient than creating a separate token chain just for the stop command. And it allows us to get rid of state STATE_STOP completely. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-03-30i2c: meson: improve interrupt handler and detect spurious interruptsHeiner Kallweit1-4/+7
If state is STATE_IDLE no interrupt should occur. Return IRQ_NONE if such a spurious interrupt is detected. Not having to take care of STATE_IDLE later in the interrupt handler allows to further simplify the interrupt handler in subsequent patches of this series. In addition move resetting REG_CTRL_START bit to the start of the interrupt handler to ensure that the start bit is always reset. Currently the start bit is not reset for STATE_STOP because i2c->state is set to STATE_IDLE. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-03-30i2c: meson: remove variable count from meson_i2c_xferHeiner Kallweit1-3/+2
Variable count has always the same value as i, so we don't need it. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-03-30i2c: meson: use full 12 bits for clock dividerHeiner Kallweit1-2/+14
The clock divider has 12 bits, splitted into a 10 bit field and a 2 bit field. The extra 2 bits aren't used currently. Change this to use the full 12 bits and warn if the requested frequency is too low. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Acked-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-03-30i2c: meson: use i2c core for DT clock-frequency parsingHeiner Kallweit1-5/+3
We don't have to parse the DT manually to retrieve the bus frequency and we don't have to maintain an own default for the bus frequency. Let the i2c core do this for us. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-03-30i2c: meson: set clock divider in probe instead of setting it for each transferHeiner Kallweit1-9/+8
The bus frequency is fixed to what is set DT, therefore we can set the clock divider in probe already and we don't have to set it for each transfer. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-03-30i2c: meson: remove member irq from struct meson_i2cHeiner Kallweit1-7/+5
Member irq can be replaced with a local variable in probe because it's nowhere else accessed. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-03-30i2c: meson: use min instead of min_t where min_t isn't neededHeiner Kallweit1-5/+5
Use min instead of min_t where min_t isn't needed. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-03-24i2c: mux: pca954x: Add missing pca9546 definition to chip_descMike Looijmans1-1/+5
The spec for the pca9546 was missing. This chip is the same as the pca9545 except that it lacks interrupt lines. While the i2c_device_id table mapped the pca9546 to the pca9545 definition the compatible table did not. Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Peter Rosin <peda@axentia.se>
2017-03-23Revert "i2c: mux: pca954x: Add ACPI support for pca954x"Andy Shevchenko1-27/+1
In ACPI world any ID should be carefully chosen and registered officially. The commit bbf9d262a147 seems did a wrong assumption because PCA is the registered PNP ID for "PHILIPS BU ADD ON CARD". I'm pretty sure this prefix has nothing to do with the driver in question. Moreover, newer ACPI specification has a support of _DSD method and special device IDs to allow drivers be enumerated via compatible string. The slight change to support this kind of enumeration will be added in sequential patch against pca954x.c. Revert the commit bbf9d262a147 for good. Cc: Tin Huynh <tnhuynh@apm.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Peter Rosin <peda@axentia.se>
2017-03-23i2c: thunderx: ACPI support for clock settingsJan Glauber1-9/+15
Add support for reading the system clock and the TWSI clock frequency from ACPI DSDT. TWSI clock was already covered by using device_property_read(). Signed-off-by: Jan Glauber <jglauber@cavium.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-03-23i2c: xlp9xx: update for ARCH_THUNDER2Jayachandran C2-1/+2
ARCH_VULCAN arm64 platform (for Broadcom Vulcan ARM64 processors) has been discontinued. Cavium's ThunderX2 CN99XX (ARCH_THUNDER2) will be the next revision of the platform. Update compile dependencies and ACPI ID to reflect this change. There is not need to retain ARCH_VULCAN since the Vulcan processor was never in production and the config option will be removed soon. Signed-off-by: Jayachandran C <jnair@caviumnetworks.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>