| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Fixes enable/disable irq handling at various points. The driver needs to
only enable/disable irqs if there is an actual irq handler installed.
Signed-off-by: Daniel Campello <campello@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Follows spec sheet for macro declarations.
Signed-off-by: Daniel Campello <campello@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Support for AMS AS73211 JENCOLOR(R) Digital XYZ Sensor.
This driver has no built-in trigger. In order for making triggered
measurements, an external (software) trigger driver like
iio-trig-hrtimer or iio-trig-sysfs is required.
The sensor supports single and continuous measurement modes. The latter
is not used by design as this would require tight timing synchronization
between hardware and driver without much benefit.
Datasheet: https://ams.com/documents/20143/36005/AS73211_DS000556_3-01.pdf
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Reading from the chip should be unlocked on error path else the lock
could never being released.
Fixes: 07914c84ba30 ("iio: adc: Add driver for Microchip MCP3422/3/4 high resolution ADC")
Fixes: 3f1093d83d71 ("iio: adc: mcp3422: fix locking scope")
Acked-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Link: https://lore.kernel.org/r/20200901093218.1500845-1-angelo.compagnucci@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Locking should be held for the entire reading sequence involving setting
the channel, waiting for the channel switch and reading from the
channel.
If not, reading from a channel can result mixing with the reading from
another channel.
Fixes: 07914c84ba30 ("iio: adc: Add driver for Microchip MCP3422/3/4 high resolution ADC")
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Link: https://lore.kernel.org/r/20200819075525.1395248-1-angelo.compagnucci@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
On the older-gen 32-bit SoCs the meson-saradc driver is used to read the
SoC temperature. This requires reading calibration data from the eFuse.
Looking up the calibration data nvmem-cell requires the OF device_node
pointer to be available in the struct device which is passed to
devm_nvmem_cell_get(). This however got lost with commit 8cb631ccbb1952
("iio: Remove superfluous of_node assignments") from indio_dev->dev. As
devm_nvmem_cell_get() is called in the initialization phase the
device_node is not yet available because the NVMEM cell is looked up
before iio_device_register() is called (which would then set the
device_node automatically).
Use the parent device to look up the NVMEM cell instead to fix this
issue.
Fixes: 8cb631ccbb1952 ("iio: Remove superfluous of_node assignments")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data.
This data is allocated with kzalloc so no data can leak apart
from previous readings.
The explicit alignment of ts is necessary to ensure correct padding
on architectures where s64 is only 4 bytes aligned such as x86_32.
Fixes: a9e9c7153e96 ("iio: adc: add max1117/max1118/max1119 ADC driver")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
|
|
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 32 byte array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data with alignment
explicitly requested. This data is allocated with kzalloc so no
data can leak apart from previous readings. The explicit alignment
isn't technically needed here, but it reduced fragility and avoids
cut and paste into drivers where it will be needed.
If we want this in older stables will need manual backport due to
driver reworks.
Fixes: c43a102e67db ("iio: ina2xx: add support for TI INA2xx Power Monitors")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Cc: Marc Titinger <mtitinger@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
|
|
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv().
This data is allocated with kzalloc so no data can leak apart from
previous readings.
The force alignment of ts is not strictly necessary in this case
but reduces the fragility of the code.
Fixes: 3691e5a69449 ("iio: adc: add driver for the ti-adc084s021 chip")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mårten Lindahl <martenli@axis.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
|
|
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv().
This data is allocated with kzalloc so no data can leak apart
from previous readings.
The eplicit alignment of ts is necessary to ensure correct padding
on x86_32 where s64 is only aligned to 4 bytes.
Fixes: 08e05d1fce5c ("ti-adc081c: Initial triggered buffer support")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
|
|
After the replacement of the /* fall through */ comment with the
fallthrough pseudo-keyword macro, the natural reading of a code
comment was broken.
Fix the natural reading of such a comment and make it intelligible.
Reported-by: Peter Rosin <peda@axentia.se>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
A follow-up patch will extend the number of errors reported by
cros_ec_cmd_xfer_status(). Specifically, the function will return
-EOPNOTSUPP if a command is not supported by the EC. Prepare for it.
Cc: Gwendal Grignou <gwendal@chromium.org>
Cc: Yu-Hsuan Hsu <yuhsuan@chromium.org>
Cc: Prashant Malani <pmalani@chromium.org>
Cc: Brian Norris <briannorris@chromium.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data.
This data is allocated with kzalloc so no data can leak apart from
previous readings.
The explicit alignment of ts is not necessary in this case as by
coincidence the padding will end up the same, however I consider
it to make the code less fragile and have included it.
Fixes: bc11ca4a0b84 ("iio:magnetometer:ak8975: triggered buffer support")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Gregor Boirie <gregor.boirie@parrot.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
|
|
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
Here we use a structure on the stack. The driver already did an
explicit memset so no data leak was possible.
Forced alignment of ts is not strictly necessary but probably makes
the code slightly less fragile.
Note there has been some rework in this driver of the years, so no
way this will apply cleanly all the way back.
Fixes: 2690be905123 ("iio: Add Lite-On ltr501 ambient light / proximity sensor driver")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
|
|
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 16 byte array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv().
This data is allocated with kzalloc so no data can leak appart
from previous readings.
It is necessary to force the alignment of ts to avoid the padding
on x86_32 being different from 64 bit platorms (it alows for
4 bytes aligned 8 byte types.
Fixes: 06ad7ea10e2b ("max44000: Initial triggered buffer support")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
|
|
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data with alignment
explicitly requested. This data is allocated with kzalloc so no
data can leak appart from previous readings.
The explicit alignment of ts is necessary to ensure consistent
padding for x86_32 in which the ts would otherwise be 4 byte aligned.
Fixes: 283d26917ad6 ("iio: chemical: ccs811: Add triggered buffer support")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Narcisa Ana Maria Vasile <narcisaanamaria12@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
|
|
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 16 byte s16 array on the stack As Lars also noted
this anti pattern can involve a leak of data to userspace and that
indeed can happen here. We close both issues by moving to
a suitable structure in the iio_priv() data with alignment
ensured by use of an explicit c structure. This data is allocated
with kzalloc so no data can leak appart from previous readings.
In this case the forced alignment of the ts is necessary to ensure
correct padding on x86_32 where the s64 would only be 4 byte aligned.
Fixes: 16b05261537e ("mb1232.c: add distance iio sensor with i2c")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: <Stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
|
|
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 16 byte u8 array on the stack As Lars also noted
this anti pattern can involve a leak of data to userspace and that
indeed can happen here. We close both issues by moving to
a suitable structure in the iio_priv() data with alignment
ensured by use of an explicit c structure. This data is allocated
with kzalloc so no data can leak appart from previous readings.
The force alignment of ts is not strictly necessary in this particularly
case but does make the code less fragile.
Fixes: a84ef0d181d9 ("iio: accel: add Freescale MMA7455L/MMA7456L 3-axis accelerometer driver")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: <Stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
|
|
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 16 byte array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by moving
to a suitable structure in the iio_priv() data with alignment
ensured by use of an explicit c structure. This data is allocated
with kzalloc so no data can leak appart from previous readings.
Fixes tag is beyond some major refactoring so likely manual backporting
would be needed to get that far back.
Whilst the force alignment of the ts is not strictly necessary, it
does make the code less fragile.
Fixes: 3bbec9773389 ("iio: bmc150_accel: add support for hardware fifo")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
|
|
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 16 byte u8 array on the stack. As Lars also noted
this anti pattern can involve a leak of data to userspace and that
indeed can happen here. We close both issues by moving to
a suitable structure in the iio_priv() data with alignment
ensured by use of an explicit c structure. This data is allocated
with kzalloc so no data can leak appart from previous readings.
The additional forcing of the 8 byte alignment of the timestamp
is not strictly necessary but makes the code less fragile by
making this explicit.
Fixes: c7eeea93ac60 ("iio: Add Freescale MMA8452Q 3-axis accelerometer driver")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
|
|
iio_push_to_buffers_with_timestamp assumes 8 byte alignment which
is not guaranteed by an array of smaller elements.
Note that whilst in this particular case the alignment forcing
of the ts element is not strictly necessary it acts as good
documentation. Doing this where not necessary should cut
down on the number of cut and paste introduced errors elsewhere.
Fixes: 0427a106a98a ("iio: accel: kxsd9: Add triggered buffer handling")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
|
|
The kernel fails to compile due to undefined reference to
devm_iio_triggered_buffer_setup() if IIO_TRIGGERED_BUFFER is not
enabled. The original patch [1] had this dependency. But somehow it
didn't make it into the kernel tree. Re-add it.
[1] https://lore.kernel.org/lkml/20200623233011.2319035-3-heiko@sntech.de/
Fixes: 4e130dc7b413 ("iio: adc: rockchip_saradc: Add support iio buffers")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
To stop conversion ads1015_set_power_state() function call unimplemented
function __pm_runtime_suspend() from pm_runtime_put_autosuspend()
if CONFIG_PM is not set.
In case of CONFIG_PM is not set: __pm_runtime_suspend() returns -ENOSYS,
so ads1015_read_raw() failed because ads1015_set_power_state() returns an
error.
If CONFIG_PM is disabled, there is no need to start/stop conversion.
Fix it by adding return 0 function variant if CONFIG_PM is not set.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Fixes: ecc24e72f437 ("iio: adc: Add TI ADS1015 ADC driver support")
Tested-by: Maxim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
BMI160 Minimium gyroscope frequency in normal mode is 25Hz.
When older EC firmware do not report their sensors frequencies,
use 25Hz as the minimum for gyroscope to be sure it works on BMI160.
Fixes: ae7b02ad2f32d ("iio: common: cros_ec_sensors: Expose cros_ec_sensors frequency range via iio sysfs")
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
ADXRS290 is a high performance MEMS pitch and roll (dual-axis in-plane)
angular rate sensor (gyroscope) designed for use in stabilization
applications. It also features an internal temperature sensor and
programmable high-pass and low-pass filters.
Add support for ADXRS290 in direct-access mode for now.
Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/ADXRS290.pdf
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Nishant Malpani <nish.malpani25@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Make sure that the trigger function stubs are all static inline.
Otherwise we might see compiler warnings about declared but unused
functions.
Fixes 77712e5fbe2e4: ("Staging: iio: Staticise non-exported functions")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The change is mostly cosmetic. When looking into the menuconfig help of the
ad8366 driver, the HMC1119 chip should also show up (since the driver
supports it).
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The driver does not have a struct of_device_id table, but supported
devices are registered via Device Trees. This patch adds OF device ID
table.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The change is mostly stylistic. The table should be indented with tabs
instead of spaces.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The driver pretty much uses device managed functions. The only left-over is
the iio_device_register() function, which also requires an action-or-reset
hook to disable the regulator on the remove and error path.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add support for the Atlas EZO O2 chemical sensor which required
some refactoring of the driver and parsing of i2c transfer.
Sensor data is converted by the scaling value from percent to
IIO_CONCENTRATION.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add modifier IIO_MOD_O2 for O2 concentration reporting
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Reset hw time samples generator after system resume in order to avoid
disalignment between system and device time reference since FIFO
batching and time samples generator are disabled during suspend.
Fixes: 213451076bd3 ("iio: imu: st_lsm6dsx: add hw timestamp support")
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
There are 2 exit paths where the lock isn't held, but try to unlock the
mutex when exiting. In these places we should just return from the
function.
A neater approach would be to cleanup the ad5592r_read_raw(), but that
would make this patch more difficult to backport to stable versions.
Fixes 56ca9db862bf3: ("iio: dac: Add support for the AD5592R/AD5593R ADCs/DACs")
Reported-by: Charles Stanhope <charles.stanhope@gmail.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Immutable branch may be needed in input for a joystick set that is
dependent on it.
|
|
This was introduced initially via commit 78289b4a58b58 ("iio: core: pass
parent device as parameter during allocation"), but was accidentally
removed via commit 6d4ebd565d15f ("iio: core: wrap IIO device into an
iio_dev_opaque object").
This looks like a rebase gone wrong, and ends up breaking devicetree
bindings of IIO clients.
This change adds back the parent assignment.
Fixes 6d4ebd565d15f: ("iio: core: wrap IIO device into an iio_dev_opaque object")
Reported-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Tested-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This change does the following:
* removes the SPI device table in favor of the OF device table
* adds 'name' && 'chip_id' fields to chip_info
* implements chip ID & silicon revision checking; the device ID for
AD7124-4 is 0x0, so just checking that value can be useless;
but at least the silicon revision isn't 0, so a non-zero value can be
used to check that "a" device is on the SPI bus; it's probably the best
way to narrow it down to one of the 2 AD7124 chip IDs
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The SADC component in JZ47xx SoCs provides support for touchscreen
operations (pen position and pen down pressure) in single-ended and
differential modes.
The touchscreen component of SADC takes a significant time to stabilize
after first receiving the clock and a delay of 50ms has been empirically
proven to be a safe value before data sampling can begin.
Of the known hardware to use this controller, GCW Zero and Anbernic RG-350
utilize the touchscreen mode by having their joystick(s) attached to the
X/Y positive/negative input pins.
JZ4770 and later SoCs introduce a low-level command feature. With it, up
to 32 commands can be programmed, each one corresponding to a sampling
job. It allows to change the low-voltage reference, the high-voltage
reference, have them connected to VCC, GND, or one of the X-/X+ or Y-/Y+
pins.
This patch introduces support for 6 stream-capable channels:
- channel #0 samples X+/GND
- channel #1 samples Y+/GND
- channel #2 samples X-/GND
- channel #3 samples Y-/GND
- channel #4 samples X+/X-
- channel #5 samples Y+/Y-
Being able to sample X-/GND and Y-/GND is useful on some devices, where
one joystick is connected to the X+/Y+ pins, and a second joystick is
connected to the X-/Y- pins.
All the boards which probe this driver have the interrupt provided from
Device Tree, with no need to handle a case where the IRQ was not provided.
Co-developed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Instead of having one array of struct iio_chan_spec for all SoCs, and
have some SoCs remove the last item of the array as they can't use it,
have each SoC define its array of supported channels.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Provide an of_xlate callback in order to retrieve the correct channel
specifier index from the IIO channels array.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Tested-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Introduce error checks for the clk_enable calls used in this driver.
As part of the changes, move clk_enable/clk_disable calls out of
ingenic_adc_set_config and into respective logic of its callers.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Tested-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The STK3311 chip has a variant called STK3311-X, which has a different
chip id of 0x12.
Add the chip id to the driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The change is more cosmetic. There is no need to reference this table in
the probe function since 'of_device_get_match_data' is used, which obtains
this information from the driver object.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This is the only use of kerneldoc in the source file and no
descriptions are provided.
Fixes the following W=1 kernel build warning(s):
drivers/iio/adc/rockchip_saradc.c:190: warning: Function parameter or member 'reset' not described in 'rockchip_saradc_reset_controller'
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
It doesn't make sense to move it into '*core*' as it's co-located with
other, similar definitions which are used in multiple locations.
Fixes the following W=1 kernel build warning(s):
In file included from drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_i2c.c:17:
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h:497:44: warning: ‘st_lsm6dsx_accel_ext_info’ defined but not used [-Wunused-const-variable=]
497 | static const struct iio_chan_spec_ext_info st_lsm6dsx_accel_ext_info[] = {
| ^~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_spi.c:17:
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h:497:44: warning: ‘st_lsm6dsx_accel_ext_info’ defined but not used [-Wunused-const-variable=]
497 | static const struct iio_chan_spec_ext_info st_lsm6dsx_accel_ext_info[] = {
| ^~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_i3c.c:16:
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h:497:44: warning: ‘st_lsm6dsx_accel_ext_info’ defined but not used [-Wunused-const-variable=]
497 | static const struct iio_chan_spec_ext_info st_lsm6dsx_accel_ext_info[] = {
| ^~~~~~~~~~~~~~~~~~~~~~~~~
Cc: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
No attempt has been made to document any of the demoted functions here.
Fixes the following W=1 kernel build warning(s):
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:174: warning: Function parameter or member 'hw' not described in 'st_lsm6dsx_shub_read_output'
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:174: warning: Function parameter or member 'data' not described in 'st_lsm6dsx_shub_read_output'
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:174: warning: Function parameter or member 'len' not described in 'st_lsm6dsx_shub_read_output'
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:205: warning: Function parameter or member 'hw' not described in 'st_lsm6dsx_shub_write_reg'
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:205: warning: Function parameter or member 'addr' not described in 'st_lsm6dsx_shub_write_reg'
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:205: warning: Function parameter or member 'data' not described in 'st_lsm6dsx_shub_write_reg'
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:205: warning: Function parameter or member 'len' not described in 'st_lsm6dsx_shub_write_reg'
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:285: warning: Function parameter or member 'sensor' not described in 'st_lsm6dsx_shub_read'
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:285: warning: Function parameter or member 'addr' not described in 'st_lsm6dsx_shub_read'
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:285: warning: Function parameter or member 'data' not described in 'st_lsm6dsx_shub_read'
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:285: warning: Function parameter or member 'len' not described in 'st_lsm6dsx_shub_read'
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:335: warning: Function parameter or member 'sensor' not described in 'st_lsm6dsx_shub_write'
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:335: warning: Function parameter or member 'addr' not described in 'st_lsm6dsx_shub_write'
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:335: warning: Function parameter or member 'data' not described in 'st_lsm6dsx_shub_write'
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:335: warning: Function parameter or member 'len' not described in 'st_lsm6dsx_shub_write'
Cc: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/iio/magnetometer/ak8974.c:200: warning: Function parameter or member 'scan' not described in 'ak8974'
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Kerneldoc is only suitable for documenting functions and struct/enums.
Fixes the following W=1 kernel build warning(s):
drivers/iio/adc/qcom-pm8xxx-xoadc.c:133: warning: Excess function parameter 'PM8XXX_CHANNEL_INTERNAL' description in 'PM8XXX_CHANNEL_INTERNAL'
drivers/iio/adc/qcom-pm8xxx-xoadc.c:133: warning: Excess function parameter 'PM8XXX_CHANNEL_125V' description in 'PM8XXX_CHANNEL_INTERNAL'
drivers/iio/adc/qcom-pm8xxx-xoadc.c:133: warning: Excess function parameter 'PM8XXX_CHANNEL_INTERNAL_2' description in 'PM8XXX_CHANNEL_INTERNAL'
drivers/iio/adc/qcom-pm8xxx-xoadc.c:133: warning: Excess function parameter 'PM8XXX_CHANNEL_MUXOFF' description in 'PM8XXX_CHANNEL_INTERNAL'
drivers/iio/adc/qcom-pm8xxx-xoadc.c:412: warning: Function parameter or member 'variant' not described in 'pm8xxx_xoadc'
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This is the only use of kerneldoc in the source file and no
descriptions are provided.
Fixes the following W=1 kernel build warning(s):
drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c:118: warning: Function parameter or member 'irq' not described in 'inv_mpu6050_read_fifo'
drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c:118: warning: Function parameter or member 'p' not described in 'inv_mpu6050_read_fifo'
Cc: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
Daniel Campello
Christian Eggers
Angelo Compagnucci
Martin Blumenstingl
Jonathan Cameron
Gustavo A. R. Silva
Guenter Roeck
Michael Walle
Maxim Kochetkov
Gwendal Grignou
Nishant Malpani
Lars-Peter Clausen
Alexandru Ardelean
Stefan Popa
Matt Ranostay
Lorenzo Bianconi
Artur Rojek
Paul Cercueil
Icenowy Zheng
Lee Jones