aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/infiniband/hw (follow)
AgeCommit message (Collapse)AuthorFilesLines
2007-10-09IB/ipath: Remove duplicate copy of LMCRalph Campbell4-26/+29
The LMC value was being saved by the SMA in two places. This patch cleans it up so only one copy is kept. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Add ability to set the LMC via the sysfs debugging interfaceRalph Campbell1-1/+39
This patch adds the ability to set the LMC via a sysfs file as if the SM sent a SubnSet(PortInfo) MAD. It is useful for debugging when no SM is running. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Optimize completion queue entry insertion and pollingRalph Campbell2-47/+53
The code to add an entry to the completion queue stored the QPN which is needed for the user level verbs view of the completion queue entry but the kernel struct ib_wc contains a pointer to the QP instead of a QPN. When the kernel polled for a completion queue entry, the QPN was lookup up and the QP pointer recovered. This patch stores the CQE differently based on whether the CQ is a kernel CQ or a user CQ thus avoiding the QPN to QP lookup overhead. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Implement IB_EVENT_QP_LAST_WQE_REACHEDRalph Campbell3-5/+29
This patch implements the IB_EVENT_QP_LAST_WQE_REACHED event which is needed by ib_ipoib to destroy the QP when used in connected mode. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Generate flush CQE when QP is in error stateRalph Campbell1-2/+20
Follow the IB spec. (C10-96) for post send which states that a flushed completion event should be generated for work requests posted when a QP is in the error state. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Remove redundant codeRalph Campbell1-5/+0
This patch removes some redundant initialization code. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Future proof eeprom checksum code (contents reading)Dave Olson1-2/+8
In an earlier change, the amount of data read from the flash was mistakenly limited to the size known to the current driver. This causes problems when the length is increased, and written with the new longer version; the checksum would fail because not enough data was read. Always read the full 128 byte length to prevent this. Signed-off-by: Dave Olson <dave.olson@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: UC RDMA WRITE with IMMEDIATE doesn't send the immediateRalph Campbell1-10/+11
This patch fixes a bug in the receive processing for UC RDMA WRITE with immediate which caused the last packet to be dropped. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Correctly describe workaround for TID write chip bugDave Olson1-5/+8
This is a comment change, only, correcting the comment to match the implemented workaround, rather than the original workaround, and clarifying why it's needed. Signed-off-by: Dave Olson <dave.olson@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Remove unneeded code for ipathfsRalph Campbell1-187/+0
The ipathfs file system is used to export binary data verses ASCII data such as through /sys. This patch removes some unneeded files since the data is available through other /sys files. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Verify host bus bandwidth to chip will not limit performanceDave Olson1-0/+86
There have been a number of issues where host bandwidth via HT or PCIe to the InfiniPath chip has been limited in some fashion (BIOS, configuration, etc.), resulting in user confusion. This check gives a clear warning that something is wrong and needs to be resolved. Signed-off-by: Dave Olson <dave.olson@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Change UD to queue work requests like RC & UCRalph Campbell7-611/+494
The code to post UD sends tried to process work requests at the time ib_post_send() is called without using a WQE queue. This was fine as long as HW resources were available for sending a packet. This patch changes UD to be handled more like RC and UC and shares more code. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: Performance optimization for CPU differencesRalph Campbell4-35/+53
Different processors have different ordering restrictions for write combining. By taking advantage of this, we can eliminate some write barriers when writing to the send buffers. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ipath: iba6110 rev4 GPIO counters supportArthur Jones2-2/+10
On iba6110 rev4, support for three more IB counters were added. The LocalLinkIntegrityError counter, the ExcessiveBufferOverrunErrors counter and support for error counting of flow control packets on an invalid VL. These counters trigger GPIO interrupts and the sw keeps track of the counts. Since we also use GPIO interrupts to signal packet reception, we need to turn off the fast interrupts, or we risk losing a GPIO interrupt. Signed-off-by: Arthur Jones <arthur.jones@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ehca: Fix clipping of device limits to INT_MAXRoland Dreier1-16/+16
Doing min_t(int, foo, INT_MAX) doesn't work correctly, because if foo is bigger than INT_MAX, then when treated as a signed integer, it will become negative and hence such an expression is just an elaborate NOP. Fix such cases in ehca to do min_t(unsigned, foo, INT_MAX) instead. This fixes negative reported values for max_cqe, max_pd and max_ah: Before: max_cqe: -64 max_pd: -1 max_ah: -1 After: max_cqe: 2147483647 max_pd: 2147483647 max_ah: 2147483647 Based on a bug report and fix from Anton Blanchard <anton@samba.org>. Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/mthca: Use mmiowb() to avoid firmware commands getting jumbled upRoland Dreier1-0/+6
Firmware commands are sent to the HCA by writing multiple words to a command register block. Access to this block of registers is serialized with a mutex. However, on large SGI systems, problems were seen with multiple CPUs issuing FW commands at the same time, because the writes to the register block may be reordered within the system interconnect and reach the HCA in a different order than they were issued (even with the mutex). Fix this by adding an mmiowb() before dropping the mutex. Tested-by: Arthur Kepner <akepner@sgi.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/mthca: Increase max number of QPs per multicast group to 56Roland Dreier1-1/+1
Increase the number of QPs allowed per multicast group from 8 to 56. This allows for one QP per core on 16-core systems, which are now quite common, and allows some space for future growth. This is basically the same patch that Jack Morgenstein <jackm@dev.mellanox.co.il> just supplied for mlx4. Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/mlx4: Implement FMRsJack Morgenstein3-0/+114
Implement FMRs for mlx4. This is an adaptation of code from mthca. Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09mlx4_core: Write MTTs from CPU instead with of WRITE_MTT FW commandJack Morgenstein1-4/+3
Write MTT entries directly to ICM from the driver (eliminating use of WRITE_MTT command). This reduces the number of FW commands needed to register an MR by at least a factor of 2 and speeds up memory registration significantly. This code will also be used to implement FMRs. Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ehca: Return srq_attr->max_sge in ehca_query_srq()Joachim Fenkes1-0/+1
Totally forgot this. Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ehca: Adjust 64-bit alignment of create QP response for userspaceHoang-Nam Nguyen1-0/+1
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ehca: Fix mem leak of firmware ctrlblock in ehca_create_srq()Hoang-Nam Nguyen1-0/+2
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/mlx4: Display misc device information under /sys/class/infiniband/Jack Morgenstein1-0/+45
display the following device information under /sys/class/infiniband/mlx4_X: board_id, fw_ver, hw_rev, hca_type. This patch makes this information available to userspace utilities such as ibstat and ibv_devinfo. Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ehca: Misc cpuinit section annotations and #ifdef cleanupsSatyam Sharma1-18/+11
* Replace {un}register_cpu_notifier with {un}register_hotcpu_notifier thereby losing a couple of #ifdef HOTPLUG_CPU pairs. * Move comp_pool_callback_nb declaration to below that of callback function so that initialization of .notifier_call and .priority can occur at build time itself and not runtime. * Mark the notifier_block (and callback function, and another static function used by it) as __cpuinit{data} for the sake of consistency and remove enclosing #ifdef. (This may increase size for modular build of this module, however, because these are no longer dropped unconditionally now.) Signed-off-by: Satyam Sharma <satyam@infradead.org> Acked-by: Joachim Fenkes <fenkes@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ehca: Only use MR large pages for hugetlb regionsJoachim Fenkes1-10/+15
...because, on virtualized hardware like System p, we can't be sure that the physical pages behind them are contiguous otherwise. Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ehca: Fix large page HW cap definesHoang-Nam Nguyen1-4/+4
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ehca: Bump version number and change its formatJoachim Fenkes1-2/+4
Nobody needed the SVNEHCA_ prefix anyway. Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ehca: Replace get_paca()->paca_index by the more portable raw_smp_processor_id()Joachim Fenkes1-7/+7
We can use raw_smp_processor_id() here because the processor ID is only used for debug output and therefore our use is preemption-unsafe. Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ehca: Serialize MR alloc and MR free hvCallsJoachim Fenkes1-7/+21
Some firmware levels exhibit a race condition between H_ALLOC_RESOURCE(MR) and H_FREE_RESOURCE(MR). Work around this problem by locking these hvCalls against each other. Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ehca: Path migration supportJoachim Fenkes2-26/+68
Fix some modify_qp() issues related to path migration. Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ehca: Add check for max #SGE to create_qp()Joachim Fenkes1-1/+13
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ehca: ehca_gen_warn() should always printJoachim Fenkes1-6/+3
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ehca: Print return codes as signed decimal integersJoachim Fenkes10-101/+100
...because -12 is easier to read than FFFFFFF4. Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ehca: Refactor hvcall tracingJoachim Fenkes1-33/+24
Change hvcall trace output towards better readability: reg numbers instead of argument numbers, return code as signed decimal instead of unsigned hex. Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ehca: Use remap_4k_pfn() to map firmware contexts to user spaceHoang-Nam Nguyen4-4/+10
Use Paul's new remap_4k_pfn() function to map our 4K firmware contexts into user space on 64K-page machines without exposing neighboring firmware contexts. Return the context's offset within a 64K page to user space so it can determine the proper virtual address. For details about remap_4k_pfn(), see commit 721151d0 or http://patchwork.ozlabs.org/linuxppc/patch?id=10281 Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ehca: Support more than 4k QPs for userspace and kernelspaceStefan Roscher4-15/+25
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ehca: Small QP userspace supportStefan Roscher2-4/+4
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/mthca: Use PCI-X/PCI-Express read control interfacesPeter Oruba1-25/+8
These driver changes incorporate the proposed PCI-X / PCI-Express read byte count interface. Reading and setting those values doesn't take place "manually", instead wrapping functions are called to allow quirks for some PCI bridges. Signed-off by: Peter Oruba <peter.oruba@amd.com> Based on work by Stephen Hemminger <shemminger@linux-foundation.org> Cc: Roland Dreier <rolandd@cisco.com> Cc: Michael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ehca: Export module parameters in sysfsAnton Blanchard1-10/+10
At the moment the ehca module parameters are not exported in sysfs. Export them with 0444 permissions. Signed-off-by: Anton Blanchard <anton@samba.org> Acked-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ehca: Make output clearer by removing some debug messagesAnton Blanchard2-6/+0
ehca spits out a lot of debugging information. I had to look closely to see the "Port 1 is not active" message within all the debug: eHCA Infiniband Device Driver (Rel.: SVNEHCA_0022) eHCA scaling code enabled ehca D.001.DQDXYCB-P1-C9: PU0006 EHCA_ERR:ehca_define_sqp Port 1 is not active. ehca D.001.DQDXYCB-P1-C9: PU0006 EHCA_ERR:ehca_create_qp ehca_define_sqp() failed rc=ffffffffffffffff ib_mad: Couldn't create ib_mad QP1 ib_mad: Couldn't open ehca0 port 1 ehca D.001.DQDXYCB-P1-C9: PU0006 EHCA_ERR:ehca_alloc_fmr unsupported fmr_attr->page_shift=9 ehca D.001.DQDXYCB-P1-C9: PU0006 EHCA_ERR:ehca_alloc_fmr rc=ffffffffffffffea pd=c000000b4b5b2420 mr_access_flags=7 fmr_attr=c0000005afd37394 fmr_create failed for FMR 0 Remove a few debug statements so that things are clearer: eHCA Infiniband Device Driver (Rel.: SVNEHCA_0022) eHCA scaling code enabled ehca D.001.DQDXYCB-P1-C9: PU0006 EHCA_ERR:ehca_define_sqp Port 1 is not active. ib_mad: Couldn't create ib_mad QP1 ib_mad: Couldn't open ehca0 port 1 ehca D.001.DQDXYCB-P1-C9: PU0006 EHCA_ERR:ehca_alloc_fmr unsupported fmr_attr->page_shift=9 fmr_create failed for FMR 0 Signed-off-by: Anton Blanchard <anton@samba.org> Acked-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/mlx4: Fix up SRQ limit_watermark endiannessRoland Dreier1-1/+1
mlx4_srq_query() returns a big-endian 16-bit value through an int *, which screws up sparse checking. Fix this so that a CPU-endian value is returned. Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/mthca: Enable MSI-X by defaultMichael S. Tsirkin1-31/+46
Recover from MSI-X errors by automatically falling back on regular interrupt, instead of asking the user to do this manually. This makes it possible to enable MSI-X by default, and will make it possible to get rid of the msi_x module option in the future. Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/ehca: Include <linux/mutex.h> from ehca_classes.hRoland Dreier1-0/+1
ehca_classes.h uses struct mutex, so while <linux/mutex.h> seems to be pulled in indirectly by one of the headers it includes, the right thing is to include <linux/mutex.h> directly. Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il> Acked-by: Stefan Roscher <stefan.roscher@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/mlx4: Use __set_data_seg() in mlx4_ib_post_recv()Roland Dreier1-5/+9
Use a __set_data_seg() helper in mlx4_ib_post_recv() too; in addition to making the code easier to read, this also allows gcc to generate better code -- on x86_64: add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-8 (-8) function old new delta mlx4_ib_post_recv 359 351 -8 Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09RDMA/cxgb3: Make the iw_cxgb3 module parameters writableSteve Wise1-8/+8
Allow changing parameter values without having to reload the module. This is safe because these parameters are only looked at when a new connection is established. Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-09-23IB/mlx4: Fix data corruption triggered by wrong headroom marking orderJack Morgenstein1-13/+49
This is an addendum to commit 0e6e7416 ("IB/mlx4: Handle new FW requirement for send request prefetching"). We also need to handle prefetch marking properly for S/G segments, or else the HCA may end up processing S/G segments that are not fully written and end up sending the wrong data. This can actually cause data corruption in practice, especially on systems with relatively slow CPUs (where the HCA is more likely to prefetch while the CPU is in the middle of writing a work request into memory). We write S/G segments in reverse order into the WQE, in order to guarantee that the first dword of all cachelines containing S/G segments is written last (overwriting the headroom invalidation pattern). The entire cacheline will thus contain valid data when the invalidation pattern is overwritten. Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-08-31Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infinibandLinus Torvalds4-25/+45
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: IB/ehca: SRQ fixes to enable IPoIB CM IB/ehca: Fix Small QP regressions
2007-08-31IB/ehca: SRQ fixes to enable IPoIB CMJoachim Fenkes2-20/+38
Fix ehca SRQ support so that IPoIB connected mode works: - Report max_srq > 0 if SRQ is supported - Report "last wqe reached" asynchronous event when base QP dies; this is required by the IB spec and IPoIB CM relies on receiving it when cleaning up. Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-08-31IB/ehca: Fix Small QP regressionsStefan Roscher2-5/+7
The new Small QP code had a few bugs that would also make it trigger for non-Small QPs. Fix them. Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-08-31cxgb3 - Fix dev->priv usageDivy Le Ray1-1/+1
cxgb3 used netdev_priv() and dev->priv for different purposes. In 2.6.23, netdev_priv() == dev->priv, cxgb3 needs a fix. This patch is a partial backport of Dave Miller's changes in the net-2.6.24 git branch. Without this fix, cxgb3 crashes on 2.6.23. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.