| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Step config setting for 5 wire touchscreen is incorrect for Y coordinates.
It was broken while we moved to DT. If you look close at the offending
commit bb76dc09ddfc ("input: ti_am33x_tsc: Order of TSC wires, made
configurable"), the change was:
- STEPCONFIG_XNP | STEPCONFIG_YPN;
+ ts_dev->bit_xn | ts_dev->bit_yp;
while bit_xn = STEPCONFIG_XNN and bit_yp = STEPCONFIG_YNN. Not quite the
same.
Fixes: bb76dc09ddfc ("input: ti_am33x_tsc: Order of TSC wires, made configurable")
Signed-off-by: Jeff Lance <j-lance1@ti.com>
[vigneshr@ti.com: Rebase to v4.14-rc1]
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Instead of stopping the touchscreen we were starting it in suspend, and
disabling it in resume.
Fixes: c899afedf168 ("Input: ucb1400_ts - convert to threaded IRQ")
Reported-by: Anton Volkov <avolkov@ispras.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
reg_addr->reg_report_rate is supposed to exist in M06, not M09.
The driver is written to skip avoids access to non-existing registers
when the register address is NO_REGISTER (0xff). But
reg_addr->reg_report_rate is initialized to 0x00 by devm_kzalloc() (in
edt_ft5x06_ts_probe()) and not changed thereafter. So the checks do
not work and an access to register 0x00 is done.
Fix by setting reg_addr->reg_report_rate to NO_REGISTER.
Also fix the only place where reg_report_rate is checked against zero
instead of NO_REGISTER.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Don't populate the const array header on the stack, instead make it
static. Makes the object code smaller by over 180 bytes:
Before:
text data bss dec hex filename
6003 1536 0 7539 1d73 surface3_spi.o
After:
text data bss dec hex filename
5726 1632 0 7358 1cbe surface3_spi.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
On some x86 tablets with a Goodix touchscreen, the Windows logo on the
front is a capacitive home button. Touching this button results in a touch
with bit 4 of the first byte set, while only the lower 4 bits (0-3) are
used to indicate the number of touches.
Report a KEY_LEFTMETA press when this happens.
Note that the hardware might support more than one button, in which
case the "id" byte of coor_data would identify the button in question.
This is not implemented as we don't have access to hardware with
multiple buttons.
Signed-off-by: Sergei A. Trusov <sergei.a.trusov@ya.ru>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Provide support for controlling reset pin. If this is not driven
correctly the device will be held in reset and will not respond.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Switch mxt_data and interrupt to resource managed allocation methods,
which cleans up the driver slightly and prepares for adding
reset GPIO support.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The thermal_zone_of_device_ops structure is only passed as the fourth
argument to devm_thermal_zone_of_sensor_register, which is declared
as const. Thus the thermal_zone_of_device_ops structure itself can
be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Fixes the following sparse warning:
drivers/input/touchscreen/mxs-lradc-ts.c:33:12: warning:
symbol 'mxs_lradc_ts_irq_names' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
[dtor: changed to static const char * const]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Function devm_ioremap() will return a NULL pointer on failure. However,
in function mxs_lradc_ts_probe(), its return value is checked with
IS_ERR(), which cannot detect the exceptional case.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
platform_get_resource() may fail, so we should better do a NULL check
and return error on failure.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This brings in devm_device_add_group() and friends so that we can create
driver-specific device attributes as managed resources.
|
|
The SUR40 labels all reported blobs as touch, token, or generic blob.
Previously, all blobs were reported as touch regardless of type, causing
lots of false positives. Present patch fixes this.
Signed-off-by: Martin Kaltenbrunner <modin@yuri.at>
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This information is unneccessary, even as debug output.
Leave commented out as documentation of the packet ID quirk.
Signed-off-by: Martin Kaltenbrunner <modin@yuri.at>
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Due to recent reverse engineering efforts, a lot more information is now
available about the internals of the SUR40. We document this in the kernel
driver for future use.
Signed-off-by: Martin Kaltenbrunner <modin@yuri.at>
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
9086 624 0 9710 25ee drivers/input/touchscreen/ads7846.o
File size After adding 'const':
text data bss dec hex filename
9198 496 0 9694 25de drivers/input/touchscreen/ads7846.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
9448 1008 0 10456 28d8 drivers/input/touchscreen/elants_i2c.o
File size After adding 'const':
text data bss dec hex filename
9496 944 0 10440 28c8 drivers/input/touchscreen/elants_i2c.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
7801 560 0 8361 20a9 drivers/input/touchscreen/raydium_i2c_ts.o
File size After adding 'const':
text data bss dec hex filename
7849 496 0 8345 2099 drivers/input/touchscreen/raydium_i2c_ts.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
We get a harmless warning when CONFIG_RUNTIME_PM is disabled:
drivers/input/touchscreen/stmfts.c:760:12: error: 'stmfts_runtime_resume' defined but not used [-Werror=unused-function]
static int stmfts_runtime_resume(struct device *dev)
drivers/input/touchscreen/stmfts.c:748:12: error: 'stmfts_runtime_suspend' defined but not used [-Werror=unused-function]
static int stmfts_runtime_suspend(struct device *dev)
The regular PM functions are already marked as __maybe_unused, so let's
do the same for the runtime-PM as well.
Fixes: 78bcac7b2ae1 ("Input: add support for the STMicroelectronics FingerTip touchscreen")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The stmfts (ST-Microelectronics FingerTip S) touchscreen device is a
capacitive multi-touch controller mainly for mobile use. It's connected
through i2c bus at the address 0x49 and it interfaces with userspace
through input event interface.
At the current state it provides a touchscreen multitouch functionality up
to 10 fingers. Each finger is enumerated with a distinctive id (from 0 to
9).
If enabled the device can support single "touch" hovering, by providing
three coordinates, x, y and distance.
It is possible to select the touchkey functionality which provides a basic
two keys interface for "home" and "back" menu, typical in mobile phones.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Merge with mainline to get acpi_dev_present() needed by patches to
axp20x-pek driver.
|
|
When we put the touchscreen controller in low-power mode the irq
pin may trigger (float) and if we then try to read a data packet we
get the following error in dmesg:
[ 478.801017] silead_ts i2c-MSSL1680:00: Data read error -121
This commit disables the irq during suspend/resume fixing this error.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Sync with mainline to bring in changes in platform drovers dropping
calls to sparse_keymap_free() so that we can remove it for good.
|
|
Pull input layer fixes from Dmitry Torokhov:
"Just a few fixups to a couple of drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - ignore signals when finishing updating firmware
Input: elan_i2c - clear INT before resetting controller
Input: atmel_mxt_ts - add T100 as a readable object
Input: edt-ft5x06 - increase allowed data range for threshold parameter
|
|
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
When using the 'object' sysfs attribute, T100 is not displayed in
the output.
Signed-off-by: Maxime Roussin-Bélanger <maxime.roussinbelanger@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The datasheet and application note does not mention an allowed range for
the M09_REGISTER_THRESHOLD parameter. One of our customers needs to set
lower values than 20 and they seem to work just fine on EDT EP0xx0M09 with
T5x06 touch.
So, lacking a known lower limit, we increase the range for thresholds,
and set the lower limit to 0. The documentation is updated accordingly.
Signed-off-by: Schoefegger Stefan <stefan.schoefegger@ginzinger.com>
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@ginzinger.com>
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
|
|
Pull input subsystem updates from Dmitry Torokhov:
- a big update from Mauro converting input documentation to ReST format
- Synaptics PS/2 is now aware of SMBus companion devices, which means
that we can now use native RMI4 protocol to handle touchpads, instead
of relying on legacy PS/2 mode.
- we removed support from BMA180 accelerometer from input devices as it
is now handled properly by IIO
- update to TSC2007 to corretcly report pressure
- other miscellaneous driver fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (152 commits)
Input: ar1021_i2c - use BIT to check for a bit
Input: twl4030-pwrbutton - use input_set_capability() helper
Input: twl4030-pwrbutton - use correct device for irq request
Input: ar1021_i2c - enable touch mode during open
Input: add uinput documentation
dt-bindings: input: add bindings document for ar1021_i2c driver
dt-bindings: input: rotary-encoder: fix typo
Input: xen-kbdfront - add module parameter for setting resolution
ARM: pxa/raumfeld: fix compile error in rotary controller resources
Input: xpad - do not suggest writing to Dominic
Input: xpad - don't use literal blocks inside footnotes
Input: xpad - note that usb/devices is now at /sys/kernel/debug/
Input: docs - freshen up introduction
Input: docs - split input docs into kernel- and user-facing
Input: docs - note that MT-A protocol is obsolete
Input: docs - update joystick documentation a bit
Input: docs - remove disclaimer/GPL notice
Input: fix "Game console" heading level in joystick documentation
Input: rotary-encoder - remove references to platform data from docs
Input: move documentation for Amiga CD32
...
|
|
Pull MFD updates from Lee Jones:
"New Drivers:
- Freescale MXS Low Resolution ADC
- Freescale i.MX23/i.MX28 LRADC touchscreen
- Motorola CPCAP Power Button
- TI LMU (Lighting Management Unit)
- Atmel SMC (Static Memory Controller)
New Device Support:
- Add support for X-Powers AXP803 to axp20x
- Add support for Dialog Semi DA9061 to da9062-core
- Add support for Intel Cougar Mountain to lpc_ich
- Add support for Intel Gemini Lake to lpc_ich
New Functionality:
- Add Device Tree support; wm831x-*, axp20x, ti-lmu, da9062, sun4i-gpadc
- Add IRQ sense support; motorola-cpcap
- Add ACPI support; cros_ec
- Add Reset support; altera-a10sr
- Add ADC support; axp20x
- Add AC Power support; axp20x
- Add Runtime PM support; atmel-ebi, exynos-lpass
- Add Battery Power Supply support; axp20x
- Add Clock support; exynos-lpass, hi655x-pmic
Fix-ups:
- Implicitly specify required headers; motorola-cpcap, intel_soc_pmic_bxtwc
- Add .remove() method; stm32-timers, exynos-lpass
- Remove unused code; intel_soc_pmic_core, intel-lpss-acpi, ipaq-micro, atmel-smc, menelaus
- Rename variables for clarity; axp20x
- Convert pr_warning() to pr_warn(); db8500-prcmu, sta2x11-mfd, twl4030-power
- Improve formatting; arizona-core, axp20x
- Use raw_spinlock_*() variants; asic3, t7l66xb, tc6393xb
- Simplify/refactor code; arizona-core, atmel-ebi
- Improve error checking; intel_soc_pmic_core
Bug Fixes:
- Ensure OMAP3630/3730 boards can successfully reboot; twl4030-power
- Correct max-register value; stm32-timers
- Extend timeout to account for clock stretching; cros_ec_spi
- Use correct IRQ trigger type; motorola-cpcap
- Fix bad use of IRQ sense register; motorola-cpcap
- Logic error "||" should be "&&"; mxs-lradc-ts"
* tag 'mfd-next-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (79 commits)
input: touchscreen: mxs-lradc: || vs && typos
dt-bindings: Add AXP803's regulator info
mfd: axp20x: Support AXP803 variant
dt-bindings: Add device tree binding for X-Powers AXP803 PMIC
dt-bindings: Make AXP20X compatible strings one per line
mfd: intel_soc_pmic_core: Fix unchecked return value
mfd: menelaus: Remove obsolete local_irq_disable() and local_irq_enable()
mfd: omap-usb-tll: Configure ULPIAUTOIDLE
mfd: omap-usb-tll: Fix inverted bit use for USB TLL mode
mfd: palmas: Fixed spelling mistake in error message
mfd: lpc_ich: Add support for Intel Gemini Lake SoC
mfd: hi655x: Add the clock cell to provide WiFi and Bluetooth
mfd: intel_soc_pmic: Fix a mess with compilation units
mfd: exynos-lpass: Add runtime PM support
mfd: exynos-lpass: Add missing remove() function
mfd: exynos-lpass: Add support for clocks
mfd: exynos-lpass: Remove pad retention control
iio: adc: add support for X-Powers AXP20X and AXP22X PMICs ADCs
mfd: cpcap: Fix bad use of IRQ sense register
mfd: cpcap: Use ack_invert interrupts
...
|
|
The MSB for the first byte of touch data transmission is always 1. Make
it a little more obvious we're testing this bit by using BIT(7).
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The device could as well be in command mode, in which this driver cannot
handle the device. When opening the device, let's make sure the device
will be in the mode we expect it to be for this driver.
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
These tests are meaningless as is because "adapt" can't possibly be both
less than 1 and greater than 32.
Fixes: d81ca730e3e4 ("input: touchscreen: mxs-lradc: Add support for touchscreen")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in drivers/input/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
cc: linux-input@vger.kernel.org
|
Jeff Lance
Dmitry Torokhov
Luca Ceresoli
Colin Ian King
Sergei A. Trusov
Sebastian Reichel
Arvind Yadav
Julia Lawall
Wei Yongjun
Pan Bian
Fabio Estevam
Florian Echtler
Arnd Bergmann
Andi Shyti
Hans de Goede
Linus Torvalds
Wolfram Sang
Maxime Roussin-Bélanger
Martin Kepplinger
Martin Kepplinger
Dan Carpenter
David Howells