| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This reverts commit f84f5b6f72e68bbaeb850b58ac167e4a3a47532a, which is
causing regressions on some platforms, preventing them to boot or do a
clean reboot. This is because the above commit is sending also all the
zero bandwidth requests to turn off any resources that might be enabled
unnecessarily, but currently this may turn off interconnects that are
enabled by default, but with no consumer to keep them on.
Let's revert this for now as some platforms are not ready for such
change yet. In the future we can introduce some _ignore_unused option
that could keep also the unused resources on platforms that have only
partial interconnect support and also add .shutdown callbacks to deal
with disabling the resources in the right order.
Reported-by: Stephen Boyd <swboyd@chromium.org>
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/CAE-0n52iVgX0JjjnYi=NDg49xP961p=+W5R2bmO+2xwRceFhfA@mail.gmail.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
We're only adding BCMs to the commit list in aggregate(), but there are
cases where pre_aggregate() is called without subsequently calling
aggregate(). In particular, in icc_sync_state() when a node with initial
BW has zero requests. Since BCMs aren't added to the commit list in
these cases, we don't actually send the zero BW request to HW. So the
resources remain on unnecessarily.
Add BCMs to the commit list in pre_aggregate() instead, which is always
called even when there are no requests.
Fixes: 976daac4a1c5 ("interconnect: qcom: Consolidate interconnect RPMh support")
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20210721175432.2119-5-mdtipton@codeaurora.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
We currently only enforce BW floors for a subset of nodes in a path.
All BCMs that need updating are queued in the pre_aggregate/aggregate
phase. The first set() commits all queued BCMs and subsequent set()
calls short-circuit without committing anything. Since the floor BW
isn't set in sum_avg/max_peak until set(), then some BCMs are committed
before their associated nodes reflect the floor.
Set the floor as each node is being aggregated. This ensures that all
all relevant floors are set before the BCMs are committed.
Fixes: 266cd33b5913 ("interconnect: qcom: Ensure that the floor bandwidth value is enforced")
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20210721175432.2119-4-mdtipton@codeaurora.org
[georgi: Removed unused variable]
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
Georgi writes:
interconnect changes for 5.14
Here are changes for the 5.14-rc1 merge window consisting of interconnect
driver updates.
Driver changes:
- New driver for SC7280 platforms.
Signed-off-by: Georgi Djakov <djakov@kernel.org>
* tag 'icc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
interconnect: qcom: Add SC7280 interconnect provider driver
dt-bindings: interconnect: Add Qualcomm SC7280 DT bindings
|
|
Add driver for the Qualcomm interconnect buses found in SC7280 based
platforms. The topology consists of several NoCs that are controlled by
a remote processor that collects the aggregated bandwidth for each
master-slave pairs.
Signed-off-by: Odelu Kukatla <okukatla@codeaurora.org>
Link: https://lore.kernel.org/r/1619517059-12109-3-git-send-email-okukatla@codeaurora.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1620704673-104205-1-git-send-email-zou_wei@huawei.com
Fixes: 976daac4a1c5 ("interconnect: qcom: Consolidate interconnect RPMh support")
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
Add a missing of_node_put() in of_bcm_voter_get() to avoid the
reference leak.
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1619116570-13308-1-git-send-email-subbaram@codeaurora.org
Fixes: 976daac4a1c5 ("interconnect: qcom: Consolidate interconnect RPMh support")
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
Pull CFI on arm64 support from Kees Cook:
"This builds on last cycle's LTO work, and allows the arm64 kernels to
be built with Clang's Control Flow Integrity feature. This feature has
happily lived in Android kernels for almost 3 years[1], so I'm excited
to have it ready for upstream.
The wide diffstat is mainly due to the treewide fixing of mismatched
list_sort prototypes. Other things in core kernel are to address
various CFI corner cases. The largest code portion is the CFI runtime
implementation itself (which will be shared by all architectures
implementing support for CFI). The arm64 pieces are Acked by arm64
maintainers rather than coming through the arm64 tree since carrying
this tree over there was going to be awkward.
CFI support for x86 is still under development, but is pretty close.
There are a handful of corner cases on x86 that need some improvements
to Clang and objtool, but otherwise works well.
Summary:
- Clean up list_sort prototypes (Sami Tolvanen)
- Introduce CONFIG_CFI_CLANG for arm64 (Sami Tolvanen)"
* tag 'cfi-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
arm64: allow CONFIG_CFI_CLANG to be selected
KVM: arm64: Disable CFI for nVHE
arm64: ftrace: use function_nocfi for ftrace_call
arm64: add __nocfi to __apply_alternatives
arm64: add __nocfi to functions that jump to a physical address
arm64: use function_nocfi with __pa_symbol
arm64: implement function_nocfi
psci: use function_nocfi for cpu_resume
lkdtm: use function_nocfi
treewide: Change list_sort to use const pointers
bpf: disable CFI in dispatcher functions
kallsyms: strip ThinLTO hashes from static functions
kthread: use WARN_ON_FUNCTION_MISMATCH
workqueue: use WARN_ON_FUNCTION_MISMATCH
module: ensure __cfi_check alignment
mm: add generic function_nocfi macro
cfi: add __cficanonical
add support for Clang CFI
|
|
Georgi writes:
interconnect changes for 5.13
These are the interconnect changes for the 5.13-rc1 merge window
with the highlights being drivers for two new platforms.
Driver changes:
- New driver for SM8350 platforms.
- New driver for SDM660 platforms.
Signed-off-by: Georgi Djakov <djakov@kernel.org>
* tag 'icc-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
interconnect: qcom: sm8350: Add missing link between nodes
interconnect: qcom: sm8350: Use the correct ids
interconnect: qcom: sdm660: Fix kerneldoc warning
MAINTAINERS: icc: add interconnect tree
interconnect: qcom: Add SM8350 interconnect provider driver
dt-bindings: interconnect: Add Qualcomm SM8350 DT bindings
interconnect: qcom: icc-rpm: record slave RPM id in error log
interconnect: qcom: Add SDM660 interconnect provider driver
dt-bindings: interconnect: Add bindings for Qualcomm SDM660 NoC
|
|
list_sort() internally casts the comparison function passed to it
to a different type with constant struct list_head pointers, and
uses this pointer to call the functions, which trips indirect call
Control-Flow Integrity (CFI) checking.
Instead of removing the consts, this change defines the
list_cmp_func_t type and changes the comparison function types of
all list_sort() callers to use const pointers, thus avoiding type
mismatches.
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210408182843.1754385-10-samitolvanen@google.com
|
|
This adds interconnect support for SM8350 SoC.
* icc-sm8350
dt-bindings: interconnect: Add Qualcomm SM8350 DT bindings
interconnect: qcom: Add SM8350 interconnect provider driver
interconnect: qcom: sm8350: Use the correct ids
interconnect: qcom: sm8350: Add missing link between nodes
Link: https://lore.kernel.org/r/20210318094617.951212-1-vkoul@kernel.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
This patch series adds the SDM660 interconnect provider driver in
order to stop some timeouts and achieve some decent performance by
avoiding to be NoC limited.
It's also providing some power consumption improvement, but I have
only measured that as less heat, which is quite important when
working on thermally constrained devices like smartphones.
Please note that this driver's yaml binding is referring to a MMCC
clock, so this series does depend on the SDM660 MMCC driver that I
have sent separately.
The multimedia clock is required only for the Multimedia NoC (mnoc).
This patch series has been tested against the following devices:
- Sony Xperia XA2 Ultra (SDM630 Nile Discovery)
- Sony Xperia 10 (SDM630 Ganges Kirin)
- Sony Xperia 10 Plus (SDM636 Ganges Mermaid)
* icc-sdm660
dt-bindings: interconnect: Add bindings for Qualcomm SDM660 NoC
interconnect: qcom: Add SDM660 interconnect provider driver
interconnect: qcom: sdm660: Fix kerneldoc warning
Link: https://lore.kernel.org/r/20201017133718.31327-1-kholk11@gmail.com
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
There is a link between the GEM NoC and C NoC nodes, which is currently
missing from the topology. Let's add it to allow consumers request paths
that use this link.
Reported-by: Alex Elder <elder@linaro.org>
Tested-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20210401094435.28937-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
For creating an array with the members for each NoC, we should be using
a local indexes, as otherwise unnecessary large arrays would be created.
Using an incorrect indexes will also result error for the consumers when
they try to find a valid path between the endpoints. Let's fix this and
use the correct ids.
Reported-by: Alex Elder <elder@linaro.org>
Acked-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20210401094334.28871-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Fix the following warning:
sdm660.c:191:warning: Function parameter or member 'regmap'
not described in 'qcom_icc_provider'
Link: https://lore.kernel.org/r/20210401094714.29075-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Add driver for the Qualcomm interconnect buses found in SM8350 based
platforms. The topology consists of several NoCs that are controlled by
a remote processor that collects the aggregated bandwidth for each
master-slave pairs.
Generated from downstream interconnect driver written by David Dai
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210318094617.951212-3-vkoul@kernel.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Add slave RPM ID to assist with identifying incorrect RPM config.
Signed-off-by: Benjamin Li <benl@squareup.com>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Link: https://lore.kernel.org/r/20210205015205.22947-2-benl@squareup.com
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Introduce a driver for the Qualcomm interconnect busses found in
the SDM630/SDM636/SDM660 SoCs.
The topology consists of several NoCs that are controlled by a
remote processor that collects the aggregated bandwidth for each
master-slave pairs.
On a note, these chips are managing the "bus QoS" in a "hybrid"
fashion: some of the paths in the topology are managed through
(and by, of course) the RPM uC, while some others are "AP Owned",
meaning that the AP shall do direct writes to the appropriate
QoS registers for the specific paths and ports, instead of sending
an indication to the RPM and leaving the job to that one.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20201017133718.31327-3-kholk11@gmail.com
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Some nodes are incorrectly marked as RPM-controlled (they have RPM
master and slave ids assigned), but are actually controlled by the
application CPU instead. The RPM complains when we send requests for
resources that it can't control. Let's fix this by replacing the IDs,
with the default "-1" in which case no requests are sent.
See commit c497f9322af9 ("interconnect: qcom: msm8916: Remove rpm-ids
from non-RPM nodes") where this was done for msm8916.
Signed-off-by: Benjamin Li <benl@squareup.com>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Link: https://lore.kernel.org/r/20210205015205.22947-3-benl@squareup.com
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Add interconnect driver support for SDX55 platform for scaling the
bandwidth requirements over RPMh.
* icc-sdx55
dt-bindings: interconnect: Add Qualcomm SDX55 DT bindings
interconnect: qcom: Add SDX55 interconnect provider driver
Link: https://lore.kernel.org/r/20210121053254.8355-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Add driver for the Qualcomm interconnect buses found in SDX55 based
platforms. The topology consists of several NoCs that are controlled by
a remote processor that collects the aggregated bandwidth for each
master-slave pairs.
Based on SM8250 driver and generated from downstream dts.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210121053254.8355-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Split shared RPM based interconnect operation code and add support for
MSM8939 interconnect.
* icc-msm8939
interconnect: qcom: Consolidate interconnect RPM support
interconnect: qcom: qcs404: use shared code
dt-bindings: interconnect: single yaml file for RPM interconnect drivers
dt-bindings: interconnect: Add Qualcomm MSM8939 DT bindings
interconnect: qcom: Add MSM8939 interconnect provider driver
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Add driver for the Qualcomm interconnect buses found in MSM8939 based
platforms. The topology consists of four NoCs that are controlled by
a remote processor that collects the aggregated bandwidth for each
master-slave pairs.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Link: https://lore.kernel.org/r/20201204075345.5161-6-jun.nie@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Use shared code for aggregate functionalities and probe function
to remove duplicated code.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Link: https://lore.kernel.org/r/20201204075345.5161-3-jun.nie@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Add RPM based interconnect driver implements the set and aggregate
functionalities that translates bandwidth requests into RPM messages.
These modules provide a common set of functionalities for all
Qualcomm RPM based interconnect providers and should help reduce code
duplication when adding new providers.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Link: https://lore.kernel.org/r/20201204075345.5161-2-jun.nie@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
When CONFIG_COMPILE_TEST is set, it is possible to build some
of the interconnect drivers into the kernel while their dependencies
are loadable modules, which is bad:
arm-linux-gnueabi-ld: drivers/interconnect/qcom/bcm-voter.o: in function `qcom_icc_bcm_voter_commit':
(.text+0x1f8): undefined reference to `rpmh_invalidate'
arm-linux-gnueabi-ld: (.text+0x20c): undefined reference to `rpmh_write_batch'
arm-linux-gnueabi-ld: (.text+0x2b0): undefined reference to `rpmh_write_batch'
arm-linux-gnueabi-ld: (.text+0x2e8): undefined reference to `rpmh_write_batch'
arm-linux-gnueabi-ld: drivers/interconnect/qcom/icc-rpmh.o: in function `qcom_icc_bcm_init':
(.text+0x2ac): undefined reference to `cmd_db_read_addr'
arm-linux-gnueabi-ld: (.text+0x2c8): undefined reference to `cmd_db_read_aux_data'
The exact dependencies are a bit complicated, so split them out into a
hidden Kconfig symbol that all drivers can in turn depend on to get it
right.
Fixes: 976daac4a1c5 ("interconnect: qcom: Consolidate interconnect RPMh support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201204165030.3747484-1-arnd@kernel.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Pull ARM device tree updates from Arnd Bergmann:
"Across all platforms, there is a continued move towards DT schema for
validating the dts files. As a result there are bug fixes for mistakes
that are found using these schema, in addition to warnings from the
dtc compiler.
As usual, many changes are for adding support for additional on-chip
and on-board components in the machines we already support.
The newly supported SoCs for this release are:
- MStar Infinity2M, a low-end IP camera chip based on a dual-core
Cortex-A7, otherwise similar to the Infinity chip we already
support. This is also known as the SigmaStar SSD202D, and we add
support for the Honestar ssd201htv2 development kit.
- Nuvoton NPCM730, a Cortex-A9 based Baseboard Management Controller
(BMC), in the same family as the NPCM750. This gets used in the
Ampere Altra based "Fii Kudo" server and the Quanta GSJ, both of
which are added as well.
- Broadcom BCM4908, a 64-bit home router chip based on Broadcom's own
Brahma-B53 CPU. Support is also added for the Asus ROG Rapture
GT-AC5300 high-end WiFi router based on this chip.
- Mediatek MT8192 is a new SoC based on eight Cortex-A76/A55 cores,
meant for faster Chromebooks and tablets. It gets added along with
its reference design.
- Mediatek MT6779 (Helio P90) is a high-end phone chip from last
year's generation, also added along with its reference board. This
one is still based on Cortex-A75/A55.
- Mediatek MT8167 is a version of the already supported MT8516 chip,
both based on Cortex-A35. It gets added along with the "Pumpkin"
single board computer, but is likely to also make its way into
low-end tablets in the future.
For the already supported chips, there are a number of new boards.
Interestingly there are more 32-bit machines added this time than
64-bit. Here is a brief list of the new boards:
- Three new Mikrotik router variants based on Marvell Prestera
98DX3236, a close relative of the more common Armada XP
- A reference board for the Marvell Armada 382
- Three new servers using ASpeed baseboard management controllers,
the actual machines being from Bytedance, Facebook and IBM, and one
machine using the Nuvoton NPCM750 BMC.
- The Galaxy Note 10.1 (P4) tablet, using an Exynos 4412.
- The usual set of 32-bit i.MX industrial/embedded hardware:
* Protonic WD3 (tractor e-cockpit)
* Kamstrup OMNIA Flex Concentrator (smart grid platform)
* Van der Laan LANMCU (food storage)
* Altesco I6P (vehicle inspection stations)
* PHYTEC phyBOARD-Segin/phyCORE-i.MX6UL baseboard
- DH electronics STM32MP157C DHCOM, a PicoITX carrier board for the
aleady supported DHCOM module
- Three new Allwinner SoC based single-board computers:
* NanoPi R1 (H3 based)
* FriendlyArm ZeroPi (H3 based)
* Elimo Initium SBC (S3 based)
- Ouya Game Console based on Nvidia Tegra 3
- Version 5 of the already supported Zynq Z-Turn MYIR Board
- LX2162AQDS, a reference platform for NXP Layerscape LX2162A, which
is a repackaged 16-core LX2160A
- A series of Kontron i.MX8M Mini baseboard/SoM versions
- Espressobin Ultra, a new variant of the popular Armada 3700 based
board,
- IEI Puzzle-M801, a rackmount network appliance based on Marvell
Armada 8040
- Microsoft Lumia 950 XL, a phone
- HDK855 and HDK865 Hardware development kits for Qualcomm sm8250 and
sm8150, respectively
- Three new board variants of the "Trogdor" Chromebook (sc7180)
- New board variants of the Renesas based "Kingfisher" and "HiHope"
reference boards
- Kobol Helios64, an open source NAS appliance based on Rockchips
RK3399
- Engicam PX30.Core, a SoM based on Rockchip PX30, along with a few
carrier boards"
* tag 'arm-soc-dt-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (679 commits)
arm64: dts: sparx5: Add SGPIO devices
arm64: dts: sparx5: Add reset support
dt-bindings: gpio: Add a binding header for the MSC313 GPIO driver
ARM: mstar: SMP support
ARM: mstar: Wire up smpctrl for SSD201/SSD202D
ARM: mstar: Add smp ctrl registers to infinity2m dtsi
ARM: mstar: Add dts for Honestar ssd201htv2
ARM: mstar: Add chip level dtsi for SSD202D
ARM: mstar: Add common dtsi for SSD201/SSD202D
ARM: mstar: Add infinity2m support
dt-bindings: mstar: Add Honestar SSD201_HT_V2 to mstar boards
dt-bindings: vendor-prefixes: Add honestar vendor prefix
dt-bindings: mstar: Add binding details for mstar,smpctrl
ARM: mstar: Fill in GPIO controller properties for infinity
ARM: mstar: Add gpio controller to MStar base dtsi
ARM: zynq: Fix incorrect reference to XM013 instead of XM011
ARM: zynq: Convert at25 binding to new description on zc770-xm013
ARM: zynq: Fix OCM mapping to be aligned with binding on zc702
ARM: zynq: Fix leds subnode name for zc702/zybo-z7
ARM: zynq: Rename bus to be align with simple-bus yaml
...
|
|
Qualcomm ARM64 DT updates for 5.11
For SM8250 the recently introduced support for handling boot-loader
stream mappings in the ARM SMMU allow us to enable this, and thereby USB
controller and PHY, SDHCI controller and FastRPC, as well as support for
the SM8250 HDK board has been added. Additionally PRNG and RTC is
enabled.
Similarly for SM8150, the ARM SMMU could be added which allows the
secondary USB controller and PHYs, as well as WiFi to be added and
support for the SM8150 HDK board to be introduced. Additionally
Coresight and support for the last-level cache controller was added.
MSM8916 finally has VDDCX and VDDMX removed as regulators and are now
handled by the rpmpd driver for the devices controlling them. The
Longsheer L8150 gains touchscreen, sensors, vibrator and LED support.
MSM8992 gains USB and SDHCI support as well as an I2C controller and the
associated RMI4 based touchscreen for the Lumia 950.
MSM8994 also gains USB and SDHCI support, as well as VADC and temp-alarm
support. Then support for the Lumia 950 XL is added.
SDM845 gains interconnect properties for a number of devices and the
GENI wrappers gains iommu stream configuration, which means DMA
operations on e.g. I2C now works. The Lenovo Yoga C630 finally has the
SMMU enabled, a few fixes and the description of the eDP bridge and
panel means that the laptop can now boot mainline with working display,
GPU, WiFi and audio.
SC7180 gains a slew of smaller improvements and fixes.
* tag 'qcom-arm64-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (93 commits)
arm64: dts: qcom: c630: Define eDP bridge and panel
arm64: dts: qcom: c630: Fix pinctrl pins properties
arm64: dts: qcom: c630: Polish i2c-hid devices
arm64: dts: qcom: sc7180: Add lpass cpu node for I2S driver
arm64: dts: sdm845: Add interconnect properties for QUP
interconnect: qcom: sdm845: Add the missing nodes for QUP
dt-bindings: interconnect: sdm845: Add IDs for the QUP ports
arm64: dts: qcom: c630: Expose LID events
arm64: dts: qcom: c630: Re-enable apps_smmu
dts: qcom: sdm845: Add dt entries to support crypto engine.
arm64: dts: qcom: qrb5165-rb5: Add support for MCP2518FD
arm64: dts: qcom: sdm845: use GIC_SPI for IPA interrupts
arm64: dts: qcom: sc7180: use GIC_SPI for IPA interrupts
arm64: dts: qcom: sc7180: limit IPA iommu streams
arm64: dts: qcom: sm8150: Add Coresight support
arm64: dts: qcom: sc7180-trogdor: Make pp3300_a the default supply for pp3300_hub
arm64: dts: qcom: sc7180: Add DDR/L3 votes for the pro variant
arm64: dts: qcom: sc7180-lite: Tweak DDR/L3 scaling on SC7180-lite
arm64: dts: qcom: sc7180-trogdor: add "pen-insert" label for trogdor
arm64: qcom: sc7180: trogdor: Add ADC nodes and thermal zone for charger thermistor
...
Link: https://lore.kernel.org/r/20201130190131.345187-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Georgi writes:
interconnect changes for 5.11
Here are the interconnect changes for the 5.10-rc1 merge window
consisting of new driver and a cleanup.
Driver changes:
- New driver for Samsung Exynos SoCs
- Misc cleanups
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
* tag 'icc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
MAINTAINERS: Add entry for Samsung interconnect drivers
interconnect: Add generic interconnect driver for Exynos SoCs
interconnect: qcom: Simplify the vcd compare function
|
|
The QUP nodes are currently defined just as entries in the topology,
but they are not referenced by any of the NoCs. Let's fix this and
"attach" them to their NoCs, so that the QUP drivers are able to use
them as path endpoints and scale their bandwidth.
This is based on the information from the downstream msm-4.9 kernel.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Link: https://lore.kernel.org/r/20201105135211.7160-2-georgi.djakov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Let's simplify the cmp_vcd() function and replace the conditionals
with just a single statement, which also improves readability.
Reviewed-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20201013171923.7351-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
The following errors are noticed during boot on a QCS404 board:
[ 2.926647] qcom_icc_rpm_smd_send mas 6 error -6
[ 2.934573] qcom_icc_rpm_smd_send mas 8 error -6
These errors show when we try to configure the GPU and display nodes.
Since these particular nodes aren't supported on RPM and are purely
local, we should just change their mas_rpm_id to -1 to avoid any
requests being sent for these master IDs.
Reviewed-by: Mike Tipton <mdtipton@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201118111044.26056-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Some nodes are incorrectly marked as RPM-controlled (they have RPM
master and slave ids assigned), but are actually controlled by the
application CPU instead. The RPM complains when we send requests for
resources that it can't control. Let's fix this by replacing the IDs,
with the default "-1" in which case no requests are sent.
Reviewed-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20201112105140.10092-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
It has been reported that on Fairphone 2 (msm8974-based), increasing
the clock rate for some of the NoCs during boot may lead to hangs.
Let's restore the original behavior and not touch the clock rate of
any of the NoCs to fix the regression.
Reported-by: Luca Weiss <luca@z3ntu.xyz>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Fixes: b1d681d8d324 ("interconnect: Add sync state support")
Link: https://lore.kernel.org/r/20201109124512.10776-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
When sync_state support got introduced recently, by default we try to
set the NoCs to run initially at maximum rate. But as these values are
aggregated, we may end with a really big clock rate value, which is
then converted from "u64" to "long" during the clock rate rounding.
But on 32bit platforms this may result an overflow. Fix it by making
sure that the rate is within range.
Reported-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Brian Masney <masneyb@onstation.org>
Link: https://lore.kernel.org/r/20201106144847.7726-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
In addition to the rest of Qcom interconnect drivers use icc_sync_state
for SM8150/SM8250 interconnect drivers to notify the interconnect
framework when all consumers are probed and there is no need to keep the
bandwidth set to maximum anymore.
Also move the BCM initialization before creating the nodes to set the
max bandwidth in hardware for the initialization/probing stage.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 7d3b0b0d8184 ("interconnect: qcom: Use icc_sync_state")
Link: https://lore.kernel.org/r/20201027133418.976687-1-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Take into account the initial bandwidth from the framework and update
the internal sum and max values before committing if needed. This will
ensure that the floor bandwidth values are enforced until the providers
get into sync state.
Fixes: 7d3b0b0d8184 ("interconnect: qcom: Use icc_sync_state")
Tested-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/20201021155938.9223-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Currently if we use sync_state, by default the bandwidth is maxed out,
but in order to set this in hardware, the BCMs (Bus Clock Managers) need
to be initialized first. Move the BCM initialization before creating the
nodes to fix this.
Fixes: 7d3b0b0d8184 ("interconnect: qcom: Use icc_sync_state")
Acked-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20201013135913.29059-3-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Currently if we use sync_state, by default the bandwidth is maxed out,
but in order to set this in hardware, the BCMs (Bus Clock Managers) need
to be initialized first. Move the BCM initialization before creating the
nodes to fix this.
Fixes: 7d3b0b0d8184 ("interconnect: qcom: Use icc_sync_state")
Acked-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20201013135913.29059-2-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
After enabling interconnect scaling for display on the db845c board,
in certain configurations the board hangs, while the following errors
are observed on the console:
Error sending AMC RPMH requests (-110)
qcom_rpmh TCS Busy, retrying RPMH message send: addr=0x50000
qcom_rpmh TCS Busy, retrying RPMH message send: addr=0x50000
qcom_rpmh TCS Busy, retrying RPMH message send: addr=0x50000
...
In this specific case, the above is related to one of the sequencers
being stuck, while client drivers are returning from probe and trying
to disable the currently unused clock and interconnect resources.
Generally we want to keep the multimedia NoC enabled like the rest of
the NoCs, so let's set the keepalive flag on it too.
Fixes: aae57773fbe0 ("interconnect: qcom: sdm845: Split qnodes into their respective NoCs")
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Reviewed-by: Mike Tipton <mdtipton@codeaurora.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20201012194034.26944-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
* icc-syncstate:
interconnect: Add get_bw() callback
interconnect: Add sync state support
interconnect: qcom: Use icc_sync_state
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Lowering the bandwidth on the bus might have negative consequences if
it's done before all consumers had a chance to cast their vote. Now by
default the framework sets the bandwidth to maximum during boot. We need
to use the icc_sync_state callback to notify the framework when all
consumers are probed and there is no need to keep the bandwidth set to
maximum anymore.
Link: https://lore.kernel.org/r/20200825170152.6434-4-georgi.djakov@linaro.org
Reviewed-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
These structures aren't modified at runtime. Mark them const so they get
moved to read-only memory. We have to cast away const in one place when
we store into the data member of struct icc_node. This is paired with a
re-const of the data member when it is extracted in qcom_icc_set().
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Link: https://lore.kernel.org/r/20200914182112.513981-1-swboyd@chromium.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Add Epoch Subsystem (EPSS) L3 interconnect provider support on
SM8250 SoCs.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200801123049.32398-6-sibis@codeaurora.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Lay the groundwork for adding Epoch Subsystem (EPSS) L3 support on
SM8250.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200801123049.32398-4-sibis@codeaurora.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Add Operation State Manager (OSM) L3 interconnect provider support on
SM8150 SoCs.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200801123049.32398-3-sibis@codeaurora.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Use the qcom_icc_xlate_extended() in order to parse tags, that are
specified as an additional arguments to the path endpoints in DT.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20200903133134.17201-7-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Use the qcom_icc_xlate_extended() in order to parse tags, that are
specified as an additional arguments to the path endpoints in DT.
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20200903133134.17201-5-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Implement a function to parse the arguments of the "interconnects" DT
property and populate the interconnect path tags if this information
is available.
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200903133134.17201-4-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Currently, bcm-voter always assumes requests are made in KBps and that
BCM HW always wants them in Bps, so it always scales the requests by
1000. However, certain use cases and BCMs may use different units.
Thus, add support for BCM-specific scaling factors.
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20200903192149.30385-7-mdtipton@codeaurora.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
Georgi Djakov
Mike Tipton
Greg Kroah-Hartman
Odelu Kukatla
Zou Wei
Subbaraman Narayanamurthy
Linus Torvalds
Sami Tolvanen
Georgi Djakov
Vinod Koul
Benjamin Li
AngeloGioacchino Del Regno
Manivannan Sadhasivam
Jun Nie
Arnd Bergmann
Dmitry Baryshkov
Stephen Boyd
Sibi Sankar